Misplaced Pages

#243756

27-414: British Standard Fine ( BSF ) is a screw thread form, as a fine-pitch alternative to British Standard Whitworth (BSW) thread. It was used for steel bolts and nuts on and in much of Britain's machinery, including cars, prior to adoption of Unified , and later Metric , standards. For highly stressed conditions, especially in motorcycles, a finer thread, British Standard Cycle (BSC), was used as well. BSF

54-478: A 47.5° thread angle and has its own set of head sizes. BA threads have diameters of 6 mm ( 0BA ) and smaller, and were and still are particularly used in precision machinery. The Whitworth 55° angle remains commonly used today worldwide in form of the 15 British standard pipe threads defined in ISO 7, which are commonly used in water supply, cooling, pneumatics, and hydraulic systems. These threads are designated by

81-812: A German company specializing in microscopes and thus equipped with tooling capable of handling threads in inches and in Whitworth. The 5 ⁄ 32  in Whitworth threads have been the standard Meccano thread for many years and it is still the thread in use by the French Meccano Company. Fixings for garden gates traditionally used Whitworth carriage bolts , and these are still the standard supplied in UK and Australia. British Morris and MG engines from 1923 to 1955 were built using metric threads with bolt heads and nuts dimensioned for Whitworth spanners and sockets. In 1919, Morris Motors took over

108-418: A number between 1/16 and 6 that originates from the nominal internal diameter (i/d) in inches of a steel pipe for which these threads were designed. These pipe thread designations do not refer to any thread diameter. Other threads that used the Whitworth 55° angle include Brass Threads , British Standard Conduit (BSCon), Model Engineers' (ME), and British Standard Copper (BSCopper). The widely used (except in

135-446: A straight flank depth of h − 2 e = 0.49249224 p ) and a radius of r = e /(1 − sin Θ ) = 0.13732908 p . Below is the historical thread size table, not to be confused with G threads, which are actually in use as British Standard Pipe . For example a G½ (half inch) is 20.955mm in diameter. To simplify matters, the term hexagon is used in this section to denote either bolt head or nut. Whitworth and BSF spanner markings refer to

162-454: Is H = p /(2tan Θ ) = 0.96049106 p . However, the top and bottom 1 ⁄ 6 of each of these triangles is cut off, so the actual depth of thread (the difference between major and minor diameters) is 2 ⁄ 3 of that value, or h = p /(3tan Θ ) = 0.64032738 p . The peaks are further reduced by rounding them with a 2×(90° − Θ ) = 180° − 55° = 125° circular arc. This arc has a height of e = H sin Θ /6 = 0.073917569 p (leaving

189-530: Is a set of technical standards for screw threads that has been adopted internationally for interconnecting and sealing pipes and fittings by mating an external ( male ) thread with an internal (female) thread. It has been adopted as standard in plumbing and pipe fitting , except in North America, where NPT and related threads are used. Two types of threads are distinguished: These can be combined into two types of joints: The thread form follows

216-552: Is that he uses Whitworth bolts. Although Axlerod does not precisely resemble any real car (whereas numerous other characters are closely modelled on real cars), he seems most closely to match the original Range Rover Classic . In reality, early model Range Rovers used parts with imperial dimensions, although the photograph of the villain's engine is virtually identical to the later 3.5-litre, single plenum Rover V8 (A design purchased from GM's Buick). Other thread standards: British Standard Pipe British Standard Pipe ( BSP )

243-460: Is the pitch. The thread pitch increases with diameter in steps specified on a chart. The Whitworth thread system was later to be adopted as a British Standard to become British Standard Whitworth (BSW). An example of the use of the Whitworth thread are the Royal Navy 's Crimean War gunboats. These are the first instance of mass-production techniques being applied to marine engineering , as

270-515: Is the same in both systems except that the thread pitch for the 1 ⁄ 2  in bolt is 12 threads per inch (tpi) in BSW versus 13 tpi in the UNC. The form of a Whitworth thread is based on a fundamental triangle with an angle of 55° at each peak and valley. The sides are at a flank angle of Θ = 27.5° perpendicular to the axis. Thus, if the thread pitch is p , the height of the fundamental triangle

297-535: The British Standard Whitworth standard: At least 41 thread sizes have been defined, ranging from ⁄ 16 to 18, although of these only 15 are included in ISO 7 and 24 in ISO 228. The size number was originally based on the inner diameter (measured in inches) of a steel tube for which the thread was intended, but contemporary pipes tend to use thinner walls to save material, and thus have an inner diameter larger than this nominal size. In

SECTION 10

#1732781070244

324-494: The Cycle Engineers' Institute (CEI) standard was used on British bicycles and motorcycles. It uses a thread angle of 60° compared to the Whitworth 55° and very fine thread pitches. The British Association screw thread (BA) standard is sometimes classed with the Whitworth standard fasteners because it is often found in the same machinery as the Whitworth standard. However it is actually a metric based standard that uses

351-586: The French Hotchkiss engine works which had moved to Coventry during the First World War. The Hotchkiss machine tools were of metric thread but metric spanners were not readily available in Britain at the time, so fasteners were made with metric thread but Whitworth heads. In the 2011 movie Cars 2 by Disney / Pixar , the vital clue to the discovery of the villain, Sir Miles Axlerod,

378-656: The US) British Standard Pipe thread, as defined by the ISO ;228 standard (formerly BS-2779), uses Whitworth standard thread form. Even in the United States, personal computer liquid cooling components use the G 1 ⁄ 4 thread from this series. The Leica Thread-Mount used on rangefinder cameras and on many enlarging lenses is 1 + 17 ⁄ 32  in by 26 turns-per-inch Whitworth, an artifact of this having been developed by

405-549: The US, BSW was replaced when steel bolts replaced iron, but was still being used for some aluminium parts as late as the 1960s and 1970s when metric -based standards International Inch replaced the U.S. inch and U.K. inch in 1951-1964. American Unified Coarse (UNC) was originally based on almost the same Imperial fractions. The Unified thread angle is 60° and has flattened crests (Whitworth crests are rounded). From 1 ⁄ 4  in up to 1 + 1 ⁄ 2  in, thread pitch

432-432: The bolt diameter, rather than the distance across the flats of the hexagon (A/F) as in other standards. Confusion can arise because each Whitworth hexagon was originally one size larger than that of the corresponding BSF fastener. This leads to instances where for example, a spanner marked 7 ⁄ 16  BSF is the same size as one marked 3 ⁄ 8  W . In both cases the spanner jaw width of 0.710 in,

459-454: The country, telling each to make ninety sets exactly in all respects to the sample. The orders were executed with unfailing regularity, and he actually completed ninety sets of engines of 60 horsepower in ninety days – a feat which made the great Continental Powers stare with wonder, and which was possible only because the Whitworth standards of measurement and of accuracy and finish were by that time thoroughly recognised and established throughout

486-649: The country. An original example of the gunboat type engine was raised from the wreck of the SS Xantho by the Western Australian Museum . On disassembly, all its threads were shown to be of the Whitworth type. With the adoption of BSW by British railway companies, many of which had previously used their own standards both for threads and for bolt head and nut profiles, and the growing need generally for standardisation in manufacturing specifications, it came to dominate British manufacturing. In

513-512: The following quotation from the obituary from The Times of 24 January 1887 for Sir Joseph Whitworth (1803–1887) shows: The Crimean War began, and Sir Charles Napier demanded of the Admiralty 120 gunboats, each with engines of 60 horsepower , for the campaign of 1855 in the Baltic . There were just ninety days in which to meet this requisition, and, short as the time was, the building of

540-428: The following sequence of blocks: Threads are normally right-hand. For left-hand threads, the letters, LH , are appended. Example: Pipe thread EN 10226 Rp 2 + 1 ⁄ 2 The terminology for the use of G and R originated from Germany ( G for gas , as it was originally designed for use on gas pipes; R for rohr , meaning pipe .) The standard ISO 7 - Pipe threads where pressure-tight joints are made on

567-401: The gunboats presented no difficulty. It was otherwise however with the engines, and the Admiralty were in despair. Suddenly, by a flash of the mechanical genius which was inherent in him, the late Mr John Penn solved the difficulty, and solved it quite easily. He had a pair of engines on hand of the exact size. He took them to pieces and he distributed the parts among the best machine shops in

SECTION 20

#1732781070244

594-430: The larger hexagons to BS 190 are now often colloquially referred to as 'pre-war' size, even though that is not strictly correct. The British Standard Fine (BSF) standard has the same thread angle as the BSW, but has a finer thread pitch and smaller thread depth. This is more like the modern "mechanical" screw and was used for fine machinery and for steel bolts. The British Standard Cycle (BSC) standard which replaced

621-478: The modern standard metric version, it is simply a size number, where listed diameter size is the major outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement. These standard pipe threads are formally referred to by

648-501: The smaller size hexagon was adopted more widely to save metal and this usage persisted thereafter. Thus it is today common to encounter a Whitworth hexagon which does not fit the nominally correct spanner and following the previous example, a more modern spanner may be marked 7 ⁄ 16  BS to indicate that they have a jaw size of 0.710 in and designed to take either the (later) 7 ⁄ 16  BSW or 7 ⁄ 16  BSF hexagon. Whitworth fasteners with

675-570: The width across the hexagon flat, is the same. Certain branches of industry used Whitworth fasteners with a smaller hexagon (identical to BSF of the same bolt diameter) under the designation "AutoWhit" or Auto-Whit and this series was formalised by the British Engineering Standards Association in 1929 as standard No. 193, with the 'original' series being No. 190 and the BSF series No. 191. During World War II

702-477: Was developed by R. E. B. Crompton , and his assistant George Field. BSF threads use the 55 degree Whitworth thread form. It was introduced by the British Engineering Standards Association in 1908. The table provides BSF sizes, the threads per inch and spanner jaw sizes. The BSC column indicates where BSF and BSC threads match. The table shows suitable tapping drill sizes. Uncommon sizes are shown in italics. British Standard Whitworth The Whitworth thread

729-419: Was the world's first national screw thread standard, devised and specified by Joseph Whitworth in 1841. Until then, the only standardization was what little had been done by individual people and companies, with some companies' in-house standards spreading a bit within their industries. Whitworth's new standard specified a 55° thread angle and a thread depth of 0.640327 p and a radius of 0.137329 p , where p

#243756