In aviation , an instrument approach or instrument approach procedure ( IAP ) is a series of predetermined maneuvers for the orderly transfer of an aircraft operating under instrument flight rules from the beginning of the initial approach to a landing , or to a point from which a landing may be made visually . These approaches are approved in the European Union by EASA and the respective country authorities and in the United States by the FAA or the United States Department of Defense for the military. The ICAO defines an instrument approach as "a series of predetermined maneuvers by reference to flight instruments with specific protection from obstacles from the initial approach fix , or where applicable, from the beginning of a defined arrival route to a point from which a landing can be completed and thereafter, if landing is not completed, to a position at which holding or en route obstacle clearance criteria apply."
45-451: The Initial Approach Fix (IAF) is the point where the initial approach segment of an instrument approach begins. An instrument approach procedure may have more than one Initial approach fix and initial approach segment. The initial approach fix is usually a designated intersection , VHF omnidirectional range (VOR), non-directional beacon (NDB), or distance measuring equipment (DME) fix. The initial approach fix may be collocated with
90-679: A back course may be available in conjunction with the localizer. Reverse sensing occurs on the back course using standard VOR equipment. With a horizontal situation indicator (HSI) system, reverse sensing is eliminated if it is set appropriately to the front course. This type of approach is similar to the ILS localizer approach, but with less precise guidance. Non-precision systems provide lateral guidance (that is, heading information), but do not provide vertical guidance (i.e., altitude or glide path guidance). Precision approach systems provide both lateral (heading) and vertical (glidepath) guidance. In
135-424: A certain level, it becomes impossible to keep aircraft following set routes separated, particularly in airspace where aircraft are climbing and descending (and therefore level separation regularly cannot be maintained). In this case controllers use "radar vectors", the issuing of headings to the pilots of aircraft on which the controller expects the pilots to fly their aircraft, to tactically keep aircraft separated in
180-587: A contact or visual approach. A visual approach is an ATC authorization for an aircraft on an IFR flight plan to proceed visually to the airport of intended landing; it is not an instrument approach procedure. A visual approach may be requested by the pilot or offered by ATC. Visual approaches are possible when weather conditions permit continuous visual contact with the destination airport. They are issued in such weather conditions in order to expedite handling of IFR traffic. The ceiling must be reported or expected to be at least 1000 feet AGL ( above ground level ) and
225-416: A decision altitude is measured above MSL (mean sea level).) The specific values for DH and/or DA at a given airport are established with intention to allow a pilot sufficient time to safely re-configure an aircraft to climb and execute the missed approach procedures while avoiding terrain and obstacles. While a DH/DA denotes the altitude at which a missed approach procedure must be started, it does not preclude
270-406: A lower amount of traffic, controllers will require pilots to navigate their aircraft on published routes which have been designed to be separated from each other. Controllers may require pilots to fly their aircraft at certain speeds or with certain minimum or maximum speeds to maintain separation between aircraft on these routes. When the amount of traffic in a particular volume of airspace reaches
315-540: A minimum vertical distance (usually 1,000-2,000 feet) or by a minimum horizontal distance. One of the means of determining horizontal separation is by a controller observing the radar returns of the aircraft to be at least a minimum horizontal distance apart. This is the essence of radar control, and is known as radar separation . Standard radar separation varies from airspace to airspace and country to country, however 3 nms in terminal airspace and 5 nms in en route airspace are common minima. In airspace with
360-524: A navigation system for course deviation but does not provide glidepath information. These approaches include VOR , NDB , LP (Localizer Performance), and LNAV. PAs and APVs are flown to a decision height/altitude (DH/DA), while non-precision approaches are flown to a minimum descent altitude (MDA). IAP charts are aeronautical charts that portray the aeronautical data that is required to execute an instrument approach to an airport. Besides depicting topographic features, hazards and obstructions, they depict
405-464: A navigation system that provides course and glidepath guidance. Examples include precision approach radar (PAR), instrument landing system (ILS), and GBAS landing system (GLS). An approach with vertical guidance also uses a navigation system for course and glidepath deviation, just not to the same standards as a PA. Examples include baro-VNAV , localizer type directional aid (LDA) with glidepath, LNAV /VNAV and LPV . A non-precision approach uses
450-402: A precision approach, the decision height (DH) or decision altitude (DA) is a specified lowest height or altitude in the approach descent at which, if the required visual reference to continue the approach (such as the runway markings or runway environment) is not visible to the pilot, the pilot must initiate a missed approach . (A decision height is measured AGL (above ground level) while
495-435: A safe landing interval behind the preceding aircraft, as well as responsibility for wake-turbulence avoidance, and to remain clear of clouds. A contact approach that may be asked for by the pilot (but not offered by ATC) in which the pilot has 1 SM flight visibility and is clear of clouds and is expected to be able to maintain those conditions all the way to the airport. Obstruction clearances and VFR traffic avoidance become
SECTION 10
#1732790919571540-457: A short distance from the airport in order to be assured of obstacle clearance (often within a couple of miles, even for faster aircraft). The pilot must maintain visual contact with the airport at all times; loss of visual contact requires execution of a missed approach procedure. Pilots should be aware that there are significant differences in obstacle clearance criteria between procedures designed in accordance with ICAO PANS-OPS and US TERPS. This
585-1121: Is 3 to 6 NM from the IF/IAF. The basic-T is aligned with the runway centerline, with the IF 5 NM from the FAF, and the FAF is 5 NM from the threshold. The RNP approach chart should have four lines of approach minimums corresponding to LPV, LNAV/VNAV, LNAV, and circling. This allows GPS or WAAS equipped aircraft to use the LNAV MDA using GPS only, if WAAS becomes unavailable. These are the most precise and accurate approaches. A runway with an ILS can accommodate 29 arrivals per hour. ILS systems on two or three runways increase capacity with parallel (dependent) ILS, simultaneous parallel (independent) ILS, precision runway monitor (PRM), and converging ILS approaches. ILS approaches have three classifications, CAT I, CAT II, and CAT III. CAT I SA, CAT II and CAT III require additional certification for operators, pilots, aircraft and equipment, with CAT III used mainly by air carriers and
630-451: Is a transition from the en route structure to the terminal environment which provides minimum altitudes for obstacle clearance. The TAA is a "T" or "basic T" design with left and right base leg IAFs on initial approach segments perpendicular to the intermediate approach segment where there is a dual purpose IF/IAF for a straight-in procedure (no procedure turn [NoPT]), or hold-in-lieu-of procedure-turn (HILPT) course reversal. The base leg IAFs
675-448: Is especially true in respect of circling approaches where the assumed radius of turn and minimum obstacle clearance are markedly different. A visual maneuver by a pilot performed at the completion of an instrument approach to permit a straight-in landing on a parallel runway not more than 1,200 feet to either side of the runway to which the instrument approach was conducted. A useful formula pilots use to calculate descent rates (for
720-509: Is permitted while doing so because of the vertical momentum involved in following a precision approach glide-path. If a runway has both non-precision and precision approaches defined, the MDA of the non-precision approach is almost always greater than the DH/DA of the precision approach, because of the lack of vertical guidance on the non-precision approach. The extra height depends on the accuracy of
765-406: Is published in tabular form. The PAR provides vertical and lateral guidance plus range. The ASR only provides heading and range information. This is a rare type of approach, where a radar installed on the approaching aircraft is used as the primary means of navigation for the approach. It is mainly used at offshore oil platforms and select military bases. This type of approach takes advantage of
810-410: Is under radar control , air traffic control (ATC) may replace some or all of these phases of the approach with radar vectors (ICAO radar vectoring is the provision of navigational guidance to aircraft in the form of specific headings, based on the use of radar). ATC will use an imaginary "approach gate" when vectoring aircraft to the final approach course. This gate will be 1 nautical mile (NM) from
855-642: The intermediate fix (IF) of the instrument approach and in such case they designate the beginning of the intermediate segment of the approach. When the initial approach fix and the intermediate fix are combined, there is no initial approach segment. Jeppesen Sanderson (2006). Guided Flight Discovery Instrument Commercial . Jeppesen Sanderson, Inc. pp. 7–3–7-4. ISBN 0-88487-387-0 . Instrument approach There are three categories of instrument approach procedures: precision approach (PA), approach with vertical guidance (APV), and non-precision approach (NPA). A precision approach uses
900-520: The FAF and at least 5 NM from the landing threshold. Outside radar environments, the instrument approach starts at the IAF. Though ground-based NAVAID approaches still exist, the FAA is transitioning to approaches which are satellite-based (RNAV). Additionally, in lieu of the published approach procedure, a flight may continue as an IFR flight to landing while increasing the efficiency of the arrival with either
945-462: The MDA, and may maintain it, but must not descend below it until visual reference is obtained, and must initiate a missed approach if visual reference has not been obtained upon reaching the missed approach point (MAP). DH/DA, the corresponding parameter for precision approach, differs from MDA in that the missed approach procedure must be initiated immediately on reaching DH/DA, if visual reference has not yet been obtained: but some overshoot below it
SECTION 20
#1732790919571990-509: The PT fix, to establish the aircraft inbound on the intermediate or final approach segment. When conducting any type of approach, if the aircraft is not lined up for a straight-in approach, then a course reversal might be necessary. The idea of a course reversal is to allow sufficiently large changes in the course flown (in order to line the aircraft up with the final approach course), without taking too much space horizontally and while remaining within
1035-413: The aircraft from descending below the prescribed DH/DA. In a non-precision approach (that is when no electronic glideslope is provided), the minimum descent altitude (MDA) is the lowest altitude, expressed in feet above mean sea level, to which descent is authorized on final approach or during circle-to-land maneuvering in execution of a standard instrument approach procedure. The pilot may descend to
1080-400: The airport, as the other runways might lack instrument procedures or their approaches cannot be used for other reasons (traffic considerations, navigation aids being out of service, etc.). Circling to land is considered more difficult and less safe than a straight-in landing, especially under instrument meteorological conditions because the aircraft is at a low altitude and must remain within
1125-401: The airport. A circle-to-land maneuver is an alternative to a straight-in landing. It is a maneuver used when a runway is not aligned within 30 degrees of the final approach course of the instrument approach procedure or the final approach requires 400 feet (or more) of descent per nautical mile, and therefore requires some visual maneuvering of the aircraft in the vicinity of the airport after
1170-469: The approach area, runways, and taxiways, and the location of emergency equipment. There must be redundant electrical systems so that in the event of a power failure, the back-up takes over operation of the required airport instrumentation (e.g., the ILS and lighting). ILS critical areas must be free from other aircraft and vehicles to avoid multipathing . In the United States, the requirements and
1215-417: The arrival direction and the final approach course are not too different from each other. The direct approach can be finished with a straight-in landing or circle-to-land procedure. Some approach procedures do not permit straight-in approaches unless the pilots are being radar vectored. In these situations, pilots are required to complete a procedure turn (PT) or other course reversal, generally within 10 NM of
1260-464: The confines of protected airspace. This is accomplished in one of three ways: a procedure turn, a holding pattern, or a teardrop course reversal. Circle-to-land is a maneuver initiated by the pilot to align the aircraft with a runway for landing when a straight-in landing from an instrument approach is not possible or is not desirable, and only after ATC authorization has been obtained and the pilot has established and maintains required visual reference to
1305-484: The information about the weather but it's the pilot who makes a decision if the weather is suitable for landing. Once the pilot has accepted the clearance, he/she assumes responsibility for separation and wake turbulence avoidance and may navigate as necessary to complete the approach visually. According to ICAO Doc. 4444, ATC continues to provide separation between the aircraft making a visual approach and other arriving and departing aircraft. The pilot may get responsible for
1350-443: The instrument portion of the approach is completed to align the aircraft with the runway for landing. It is very common for a circle-to-land maneuver to be executed during a straight-in approach to a different runway, e.g., an ILS approach to one runway, followed by a low-altitude transition, ending in a landing on another (not necessarily parallel) runway. This way, approach procedures to one runway can be used to land on any runway at
1395-449: The landing to be made. Radar control Radar control is a method of providing air traffic control services with the use of radar and Automatic Dependent Surveillance (ADS–B). The provision of air traffic control services without the use of radar is called procedural control . In air traffic control, the risk of aircraft colliding is managed by applying separation rules. These rules require aircraft to be separated by either
Initial approach fix - Misplaced Pages Continue
1440-481: The military. Simultaneous parallel approaches require runway centerlines to be between 4,300 and 9,000 feet apart, plus a "dedicated final monitor controller" to monitor aircraft separation. Simultaneous close parallel (independent) PRM approaches must have runways separation to be between 3,400 and 4,300 feet. Simultaneous offset instrument approaches (SOIAs) apply to runways separated by 750–3,000 feet. A SOIA uses an ILS/PRM on one runway and an LDA/PRM with glideslope for
1485-417: The minimum safe altitude (MSA) for emergencies. A cross depicts the final approach fix (FAF) altitude on NPAs while a lightning bolt does the same for PAs. NPAs depict the MDA while a PA shows both the decision altitude (DA) and decision height (DH). Finally, the chart depicts the missed approach procedures in plan and profile view, besides listing the steps in sequence. Before satellite navigation (GNSS)
1530-463: The navaid the approach is based on, with ADF approaches and SRAs tending to have the highest MDAs. An instrument approach wherein final approach is begun without first having executed a procedure turn, not necessarily completed with a straight-in landing or made to straight-in landing minimums. A direct instrument approach requires no procedure turn or any other course reversal procedures for alignment (usually indicated by "NoPT" on approach plates), as
1575-463: The other. These approaches use VOR facilities on and off the airport and may be supplemented with DME and TACAN. These approaches use NDB facilities on and off the airport and may be supplemented with a DME. These approaches are gradually being phased out in Western countries. This will be either a precision approach radar (PAR) or an airport surveillance radar (ASR) approach. Information
1620-543: The pilot's responsibility. A visual approach that has a specified route the aircraft is to follow to the airport. Pilots must have a charted visual landmark or a preceding aircraft in sight, and weather must be at or above the published minimums. Pilots are responsible for maintaining a safe approach interval and wake turbulence separation. These approaches include both ground-based and satellite-based systems and include criteria for terminal arrival areas (TAAs), basic approach criteria, and final approach criteria. The TAA
1665-470: The procedures and airport diagram. Each procedure chart uses a specific type of electronic navigation system such as an NDB, TACAN , VOR, ILS/ MLS and RNAV . The chart name reflects the primary navigational aid (NAVAID), if there is more than one straight-in procedure or if it is just a circling-only procedure. A communication strip on the chart lists frequencies in the order they are used. Minimum, maximum and mandatory altitudes are depicted in addition to
1710-401: The runway or more commonly, the oil platform, standing out from its surrounding environment when viewed on a radar. For additional visibility on a radar, radar reflectors may be installed alongside the runway. These approaches include a localizer approach, localizer/DME approach, localizer back course approach, and a localizer-type directional aid (LDA). In cases where an ILS is installed,
1755-459: The same runway, but from opposite directions. Aircraft approaching from the north must make visual contact with the airport at a higher altitude than a flight approaching from the south, because of rapidly rising terrain south of the airport. This higher altitude allows a flight crew to clear the obstacle if a landing is not feasible. In general, each specific instrument approach specifies the minimum weather conditions that must be present in order for
1800-406: The separation with preceding aircraft in case he/she has the preceding aircraft in sight and is instructed so by ATC. In the United States, it is required that an aircraft have the airport, the runway, or the preceding aircraft in sight. It is not enough to have the terrain in sight (see #Contact approach ). When a pilot accepts a visual approach, the pilot accepts responsibility for establishing
1845-437: The standard 3° glide slope): or For other glideslope angles: where rate of descent is in feet per minute, and ground speed is in knots . The latter replaces tan α (see below) with α/60 , which has an error of about 5% up to 10°. Example: The simplified formulas above are based on a trigonometric calculation: where: Example: Special considerations for low visibility operations include improved lighting for
Initial approach fix - Misplaced Pages Continue
1890-628: The standards for establishing instrument approaches at an airport are contained in the FAA Order 8260.3 "United States Standard for Terminal Instrument Procedures (TERPS)". ICAO publishes requirements in the ICAO Doc 8168 "Procedures for Air Navigation Services – Aircraft Operations (PANS-OPS), Volume II: Construction of Visual and Instrument Flight Procedures". Mountain airports such as Reno–Tahoe International Airport (KRNO) offer significantly different instrument approaches for aircraft landing on
1935-449: The surface in sight. ATC must ensure that weather conditions at the airport are above certain minima (in the U.S., a ceiling of 1000 feet AGL or greater and visibility of at least 3 statute miles) before issuing the clearance. According to ICAO Doc. 4444, it is enough if the pilot reports that in his/her opinion the weather conditions allow a visual approach to be made. In general, the ATC gives
1980-405: The visibility is at least 3 SM (statute miles). A pilot may accept a visual approach clearance as soon as the pilot has the destination airport in sight. According to ICAO Doc. 4444, it is enough for a pilot to see the terrain to accept a visual approach. The point is that if a pilot is familiar with the terrain in the vicinity of the airfield he/she may easily find the way to the airport having
2025-831: Was available for civilian aviation, the requirement for large land-based navigation aid (NAVAID) facilities generally limited the use of instrument approaches to land-based (i.e. asphalt, gravel, turf, ice) runways (and those on aircraft carriers ). GNSS technology allows, at least theoretically, to create instrument approaches to any point on the Earth's surface (whether on land or water); consequently, there are nowadays examples of water aerodromes (such as Rangeley Lake Seaplane Base in Maine , United States) that have GNSS-based approaches. An instrument approach procedure may contain up to five separate segments, which depict course, distance, and minimum altitude. These segments are When an aircraft
#570429