Misplaced Pages

#6993

130-449: The connectors used for registered jack installations are primarily the modular connector and the 50-pin miniature ribbon connector . For example, RJ11 and RJ14 use female six-position modular connectors, and RJ21 uses a 25-pair (50-pin) miniature ribbon connector. RJ11 uses two conductors in a six-position female modular connector, so can be made with any female six-position modular connector, while RJ14 uses four, so can be made with either

260-447: A loopback so that a signal received on one pair is returned on the other. Sometimes this is referred to as a self-looping jack . RJ48S is typically used for local-area data channels and subrate digital services and carries one line. It accepts a keyed variety of the 8P modular connector. RJ48 connectors are fastened to shielded twisted pair (STP) cables, not the unshielded twisted-pair (UTP) commonly used in other installations. RJ61

390-406: A micro ribbon connector with contacts for up to fifty conductors . It is used to implement connections for up to 25 lines , or circuits that require many wire pairs, such as used in the 1A2 key telephone system . The miniature ribbon connector of this interface is also known as a 50-pin telco connector, CHAMP(AMP), or Amphenol connector, the last being a genericized trademark , as Amphenol

520-591: A natural monopoly . The FCC controlled telephone rates and imposed other restrictions under Title II to limit the profits of AT&T and ensure nondiscriminatory pricing. In the 1960s, the FCC began allowing other long-distance companies, namely MCI, to offer specialized services. In the 1970s, the FCC allowed other companies to expand offerings to the public. A lawsuit in 1982 led by the Justice Department after AT&T underpriced other companies, resulted in

650-482: A 4P4C connector. The two center pins are commonly used for the receiver, and the outer pins connect the transmitter so that a reversal of conductors between the ends of a cord does not affect the signal routing. This may differ for other equipment, including hands-free headsets. The Macintosh 128K , Macintosh 512K and Macintosh Plus from Apple as well as the Amiga 1000 from Commodore use 4P4C connectors to connect

780-665: A 6P4C or a 6P6C connector. The registered jack designations originated in the standardization process of telephone connections in the Bell System in the United States, and describe application circuits and not just the physical geometry of the connectors. The same modular connector type may be used for different registered jack applications. Modular connectors were developed to replace older telephone installation methods that used hardwired cords or bulkier varieties of telephone plugs . Strictly, Registered Jack refers to both

910-427: A central junction box . Two of its six possible contact positions connect tip and ring , and the other two contact positions may be unused or provide low-voltage power for night light or other features on the telephone set. In some installations, an extra contact was also required for the ground connection for selective ringers . The pins of the 6P6C connector are numbered 1 to 6, counting left to right when holding

1040-431: A computer serial port to control the set-top box. Modular plugs are described by the maximum number of physical contact positions and the actual number of contacts installed in these positions. The 6P2C , 6P4C , and 6P6C modular connectors are probably best known for their use as RJ11 , RJ14 , and RJ25 non-powered registered jacks, respectively (and 6P4C and 6P6C for powered RJ11 and RJ14, power being delivered on

1170-594: A cost of $ 17.3 million per year in 1996 dollars. Prior to the Portals, the FCC had space in six buildings at and around 19th Street NW and M Street NW. The FCC first solicited bids for a new headquarters complex in 1989. In 1991 the GSA selected the Portals site. The FCC had wanted to move into a more expensive area along Pennsylvania Avenue . In 1934, Congress passed the Communications Act , which abolished

1300-450: A given plug is designed for only one type. The sharp prongs are different in the connectors made for each type of wire, and a mismatch between plug type and wire type results in unreliable connections. A modular plug for solid (single-strand) wire often has three slightly splayed prongs on each contact to securely surround and grip the conductor while scraping along the outside, and a plug for stranded wire has prongs that are designed to pierce

1430-452: A key that excludes insertion in an un-keyed 8P8C socket. The original RJ45S was intended for high-speed modems and is obsolete. The RJ45S jack mates with a keyed 8P2C modular plug, and has pins 4 and 5 (the middle positions) wired for the ring and tip conductors of a single telephone line and pins 7 and 8 shorting a programming resistor. This is a different mechanical interface and wiring scheme than ANSI/TIA-568 T568A and T568B schemes with

SECTION 10

#1732797171007

1560-458: A large number of manufacturers, whereas Tyco/AMP plugs are produced exclusively by Tyco Electronics . Both types of modular plugs can be mated with a standard 8P8C modular jack. Both types of 8P8C plugs are available in shielded and unshielded varieties for different attenuation tolerances as needed. Shielded plugs are more expensive and require shielded cable, but have a lower attenuation, and may reduce electromagnetic interference . Although

1690-424: A modular plug on one end and a jack on the other are rare. Instead, cables are usually connected using a female-to-female coupler, having two jacks wired back-to-back. Most modular connectors are designed with a latching mechanism that secures the physical connection. As a plug is inserted into a jack, a plastic tab on the plug locks against a ridge in the socket so that the plug cannot be removed without disengaging

1820-608: A narrower 4-pin and 6-pin plug fits into the wider 8-pin jack and makes a connection with the available contacts on the plug, because the body of the smaller connector may stress the remaining contacts, the smaller connector can potentially damage the springs of the larger jack. 8P8C connectors are commonly used in computer networking applications, where interconnecting cables are terminated at each end with an 8P8C modular plug wired according to TIA/EIA standards. Most wired Ethernet communications are carried over Category 5e or Category 6 cable terminated with 8P8C modular plugs. The connector

1950-410: A nominally incompatible wider jack. Termination of cables with modular connectors is similar across the various number of positions and contacts in the plug. The crimping tool contains a die that is often exchangeable and is closely matched to the shape and pin count of the modular plug. A crimping die-set looks similar to an 8P8C jack, except for the eight teeth lining the top portion of the die. When

2080-411: A one-, two-, or three-line jack . The contact positions are numbered sequentially starting from 1. When viewed head-on with the retention mechanism on the bottom, jacks will have contact position number 1 on the left and plugs will have it on the right. Contacts are numbered by the contact position. For example, on a six-position, two-contact plug, where the outermost four positions do not have contacts,

2210-460: A polarized straight-through pinout. Using a telephone handset cable instead of the supplied cable could short out the +5 volt DC supply and damage the Apple computer or the keyboard. Modular connectors are often used for data links, such as serial line connections, because of their compact dimensions. For example, some DirecTV set-top boxes include a 4P4C data port with an adapter cord to connect to

2340-504: A shorter 36-pin version known as a Centronics connector . The 8P8C modular jack was chosen as a candidate for ISDN systems. In order to be considered, the connector system had to be defined by an international standard, leading to the creation of the ISO 8877 standard. Under the rules of the IEEE 802 standards project, international standards are to be preferred over national standards, so when

2470-430: A single wiring standard in a facility can be used for both voice and data. The following RJ -style names do not refer to official ACTA types. The labels RJ9 , RJ10 , RJ22 are variously used for 4P4C and 4P2C modular connectors, most typically installed on telephone handsets and their cordage. Telephone handsets do not connect directly to the public network, and therefore have no registered jack designation. RJ45

2600-410: A situation he found "perplexing". These efforts later were documented in a 2015 Harvard Case Study. In 2017, Christine Calvosa replaced Bray as the acting CIO of FCC. On January 4, 2023, the FCC voted unanimously to create a newly formed Space Bureau and Office of International Affairs within the agency, replacing the existing International Bureau. FCC chairwoman Jessica Rosenworcel explained that

2730-447: A slot on one side to allow mating with a special variation of the 8P plug: a mechanically-keyed plug with an extra tab on one side that prevents it from mating with regular (non-keyed) 8P jacks. The visual difference from the more-common 8P female is subtle. The RJ45S keyed 8P modular connector has only pins 5 and 4 wired for tip and ring (respectively) of a single telephone line, and a "programming" resistor connected to pins 7 and 8. RJ48

SECTION 20

#1732797171007

2860-444: A switch or hub, however, most network interface cards (NIC) in use today implement auto MDI-X to automatically configure themselves based on the type of cable plugged into them. A cable wired the same at both ends is called a patch or straight-through cable , because no pin/pair assignments are swapped. If a patch or straight cable is used to connect two computers with auto MDI-X capable NICs, one NIC will configure itself to swap

2990-470: A switch with 50-pin ports to a Cat-5 rated patch panel , or between two patch panels. A cable with a 50-pin connector on one end can support six fully wired 8P8C connectors or Ethernet ports on a patch panel with one spare pair. Alternatively, only the necessary pairs for 10/100 Ethernet can be wired allowing twelve Ethernet ports with a single spare pair. This connector is also used with spring bail locks for SCSI-1 connections. Some computer printers use

3120-536: Is a physical interface that was often used for terminating twisted pair cables. It uses an eight-position, eight-conductor (8P8C) modular connector . This wiring pattern is for multi-line analog telephone use only; RJ61 is unsuitable for use with high-speed data because the pins for pairs 3 and 4 are too widely spaced for high signaling frequencies. T1 lines use another wiring for the same connector, designated RJ48 . Ethernet over twisted pair ( 10BASE-T , 100BASE-TX and 1000BASE-T ) also uses different wiring for

3250-441: Is a jack from which a wall telephone can be hung, while RJ11C is a jack designed to have a cord plugged into it. A cord can be plugged into an RJ11W as well. All of these registered jacks are described as containing a number of potential contact positions and the actual number of contacts installed within these positions. RJ11, RJ14, and RJ25 all use the same six-position modular connector , thus are physically identical except for

3380-450: Is a plug and jack allowing higher transmission rates, and the jack can, optionally, be backward-compatible with the common 8P8C plugs of Gigabit Ethernet and earlier standards. RJ50 is often a 10P10C interface, often used for data applications. The micro ribbon connector, first made by Amphenol, that is used in the RJ21 interface, has also been used to connect Ethernet ports in bulk from

3510-469: Is a utility box, usually containing surge protective circuitry, which connects the wiring on the customer's property to the communication provider's network. Customers are responsible for all jacks, wiring, and equipment on their side of the MPOE. The intent was to establish a universal standard for wiring and interfaces, and to separate ownership of in-home (or in-office) telephone wiring from the wiring owned by

3640-412: Is also used for single-line telephones in many countries other than the United States. It may also use a 6P4C connector, to use an additional wire pair for powering lamps on the telephone set. RJ14 is similar to RJ11, but is wired for two lines and RJ25 has three lines. RJ61 is a similar registered jack for four lines, but uses an 8P8C connector. The RJ45S jack is rarely used in telephone applications, and

3770-416: Is also used in other telecommunications connections, including ISDN and T1 . Where building network and telephone wiring is pre-installed, the center (blue) pair is often used to carry telephony signals. While this allows an RJ11 plug to connect, it may damage the modular jack; an approved converter prevents damage. In landline telephony, an 8P8C jack is used at the point a line enters the building to allow

3900-424: Is based on the number of contact positions and the number of contacts present. 6P indicates a six-position modular plug or jack. A six-position modular plug with conductors in only the middle two positions is designated 6P2C ; 6P4C has four conductors in the middle positions, and 6P6C has all six. An RJ11 without power, if made with a 6P6C connector, has four unused contacts. Registration interfaces were created by

4030-416: Is commonly used to connect DSL modems to the customer line. The conductors other than the two central tip and ring conductors are in practice variously used for a second or third telephone line, a ground for selective ringers , low-voltage power for a dial light, or for anti-tinkle circuitry to prevent pulse dialing phones from sounding the bell on other extensions. Observing the male connector from

Registered jack - Misplaced Pages Continue

4160-469: Is identically dimensioned and inter-connectable, whether it is wired for one, two, or three lines. These are the RJ11, RJ14, and RJ25 interfaces. The RJ standards designations only pertain to the wiring of the (female) jacks, hence the name Registered Jack . It is commonplace, but not strictly correct, to refer to the unwired connectors or the (male) plugs by these names. The nomenclature for modular connectors

4290-516: Is not compatible with RJ61, because RJ61 pairs 3 and 4 would each be split across two different twisted pairs in the patch cable, causing excessive cross-talk between voice lines 3 and 4, with conversations on each line literally being audible on the other. With the advent of structured wiring systems and TIA/EIA-568 (now ANSI/TIA-568) conventions, the RJ61 wiring pattern is falling into disuse. The T568A and T568B standards are used in place of RJ61 so that

4420-486: Is often incorrectly used when referring to an 8P8C connector used for ANSI/TIA-568 T568A and T568B and Ethernet , however, the plug used for RJ45 is both mechanically and electrically incompatible with any Ethernet port: it cannot fit into an Ethernet port, and it is wired in a way that is incompatible with Ethernet. The connector commonly used for twisted-pair Ethernet is a non-keyed 8P8C connector, quite distinct from that used for RJ45S. The new ARJ45 interface, however,

4550-401: Is organized into seven bureaus, each headed by a "chief" that is appointed by the chair of the commission. Bureaus process applications for licenses and other filings, analyze complaints, conduct investigations, develop and implement regulations, and participate in hearings . The FCC has twelve staff offices. The FCC's offices provide support services to the bureaus. The FCC leases space in

4680-715: Is specified by the ANSI/TIA-568 standard. For other applications, standardization may be lacking; for example, multiple conventions exist for the use of 8P8C connectors in RS-232 applications. For this reason, D-sub -to-modular adapters are typically shipped with the D-sub contacts (pins or sockets) terminated but not inserted into the connector body so that the D-sub-to-modular contact pairing can be assigned as needed. The four-position four-conductor ( 4P4C ) connector

4810-450: Is that the orange and green pairs (colors) are swapped. A cable wired as T568A at one end and wired as T568B at the other end (Tx and Rx pairs reversed) is an Ethernet crossover cable . Before the widespread acceptance of auto MDI-X capabilities, a crossover cable was needed to interconnect similar network equipment (such as Ethernet hubs to Ethernet hubs). Crossover cables are sometimes still used to connect two computers together without

4940-403: Is the standard modular connector used on both ends of telephone handset cords and is therefore often called a handset connector . This handset connector is not a registered jack, because it was not intended to connect directly to telephone lines. However, it is often referred to as RJ9 , RJ10 , or RJ22 . [REDACTED] Handsets and often headsets for use with telephones commonly use

5070-443: Is used for T1 and ISDN termination, local-area data channels, and subrate digital services. It uses the eight-position modular connector (8P8C). RJ48C is commonly used for T1 circuits and uses pin numbers 1, 2, 4 and 5. RJ48X is a variation that contains shorting blocks in the jack for troubleshooting: With no plug inserted, pins 2 and 5 (the two tip wires) are connected to each other, and likewise 1 and 4 ( ring ), creating

5200-497: The keyed 8P8C modular plug used for RJ45S mechanically cannot be inserted into an Ethernet port , but a similar plug, the non-keyed 8P8C modular plug – never used for RJ45S  – is used in Ethernet networks, and the connector is often, however improperly, referred to as RJ45 in this context. Many of the basic names have suffixes that indicate subtypes: For example, RJ11 comes in two forms: RJ11W

5330-399: The ANSI/TIA-568 (formerly TIA/EIA-568) and Yost standards, and other applications involving unshielded twisted pair , shielded twisted pair , and multi-conductor flat cable. An 8P8C modular connection consists of a male plug and a female jack, each with eight equally spaced contacts. On the plug, the contacts are flat metal bars positioned parallel to the connector body. Inside the jack,

Registered jack - Misplaced Pages Continue

5460-711: The Broadcast Decency Enforcement Act of 2005 sponsored by then-Senator Sam Brownback , a former broadcaster himself, and endorsed by Congressman Fred Upton of Michigan who authored a similar bill in the United States House of Representatives . The new law stiffens the penalties for each violation of the Act. The Federal Communications Commission will be able to impose fines in the amount of $ 325,000 for each violation by each station that violates decency standards. The legislation raised

5590-532: The Columbia Broadcasting System (CBS). The report limited the amount of time during the day and at what times the networks may broadcast. Previously a network could demand any time it wanted from a Network affiliate . The second concerned artist bureaus. The networks served as both agents and employers of artists, which was a conflict of interest the report rectified. In assigning television stations to various cities after World War II ,

5720-526: The Communications Act of 1934 and amended by the Telecommunications Act of 1996 (amendment to 47 U.S.C. §151), is to "make available so far as possible, to all the people of the United States, without discrimination on the basis of race, color, religion, national origin, or sex, rapid, efficient, nationwide, and world-wide wire and radio communication services with adequate facilities at reasonable charges." The act furthermore provides that

5850-705: The FCC and codified in the Code of Federal Regulations (CFR), Title 47 CFR Part 68 , Subpart F, superseded by T1.TR5-1999. In January 2001, the FCC delegated responsibility for standardizing connections to the telephone network to a new private industry organization, the Administrative Council for Terminal Attachments (ACTA). For this delegation, the FCC removed Subpart F from the CFR and added Subpart G. The ACTA derives its recommendations for terminal attachments from

5980-644: The Federal Radio Commission and transferred jurisdiction over radio licensing to a new Federal Communications Commission, including in it also the telecommunications jurisdiction previously handled by the Interstate Commerce Commission. Title II of the Communications Act focused on telecommunications using many concepts borrowed from railroad legislation and Title III contained provisions very similar to

6110-566: The Radio Act of 1927 . The initial organization of the FCC was effected July 17, 1934, in three divisions, Broadcasting, Telegraph, and Telephone. Each division was led by two of the seven commissioners, with the FCC chairman being a member of each division. The organizing meeting directed the divisions to meet on July 18, July 19, and July 20, respectively. In 1940, the Federal Communications Commission issued

6240-512: The Western Electric Company in the 1960s. This includes the 6P2C used for telephone line connections and 4P4C used for handset connectors. Registered jack designations describe the signals and wiring used for voice and data communication at customer-facing interfaces of the public switched telephone network (PSTN). It is common to use a registered jack number to refer to the physical connector itself; for instance,

6370-434: The breakup of the Bell System from AT&T. Beginning in 1984, the FCC implemented a new goal that all long-distance companies had equal access to the local phone companies' customers. Effective January 1, 1984, the Bell System's many member-companies were variously merged into seven independent "Regional Holding Companies", also known as Regional Bell Operating Companies (RBOCs), or "Baby Bells". This divestiture reduced

6500-631: The "Report on Chain Broadcasting " which was led by new FCC chairman James Lawrence Fly (and Telford Taylor as general counsel). The major point in the report was the breakup of the National Broadcasting Company (NBC), which ultimately led to the creation of the American Broadcasting Company (ABC), but there were two other important points. One was network option time, the culprit here being

6630-457: The 1960s All-Channel Receiver Act ), to make UHF viable against entrenched VHF stations. In markets where there were no VHF stations and UHF was the only TV service available, UHF survived. In other markets, which were too small to financially support a television station, too close to VHF outlets in nearby cities, or where UHF was forced to compete with more than one well-established VHF station, UHF had little chance for success. Denver had been

SECTION 50

#1732797171007

6760-559: The 1960s, and similar types found use for simple interconnection of customer-provided telephone subscriber premises equipment to the telephone network. The Federal Communications Commission (FCC) mandated in 1976 an interface registration system, in which they became known as registered jacks . The convenience of prior existence for designers and ease of use led to a proliferation of modular connectors for many other applications. Many applications that originally used bulkier, more expensive connectors have converted to modular connectors. Probably

6890-621: The 50 states, the District of Columbia , and the territories of the United States . The FCC also provides varied degrees of cooperation, oversight, and leadership for similar communications bodies in other countries in North America. The FCC is funded entirely by regulatory fees. It has an estimated fiscal-2022 budget of US $ 388 million. It has 1,482 federal employees as of July 2020. The FCC's mission, specified in Section One of

7020-527: The 8P8C connector in Ethernet and telephone applications. Generic 8P8C modular connectors are similar to those used for the RJ45S variant, although the RJ45S plug is keyed and not compatible with non-keyed 8P8C modular jacks. Telephone installers who wired RJ45S modem jacks or RJ61X telephone jacks were familiar with the pin assignments of the standard. However, the standard un-keyed modular connectors became ubiquitous for computer networking and informally inherited

7150-447: The Bell System to allow some interconnection, culminating in the development of registered interfaces using new types of miniature connectors. Registered jacks replaced the use of protective couplers provided exclusively by the telephone company. The new modular connectors were much smaller and cheaper to produce than the earlier, bulkier connectors that were used in the Bell System since the 1930s. The Bell System issued specifications for

7280-433: The Bell System under a Federal Communications Commission order for the standard interconnection between telephone company equipment and customer premises equipment . These interfaces used newly standardized jacks and plugs, primarily based on miniature modular connectors . The wired communications provider (telephone company) is responsible for delivery of services to a minimum (or main) point of entry ( MPOE ). The MPOE

7410-762: The Cable Communications Policy Act of 1984, and made substantial modifications to Title VI in the Cable Television and Consumer Protection and Competition Act of 1992. Further modifications to promote cross-modal competition (telephone, video, etc.) were made in the Telecommunications Act of 1996, leading to the current regulatory structure. Broadcast television and radio stations are subject to FCC regulations including restrictions against indecency or obscenity. The Supreme Court has repeatedly held, beginning soon after

7540-522: The FCC a legal basis for imposing net neutrality rules (see below), after earlier attempts to impose such rules on an "information service" had been overturned in court. In 2005, the FCC formally established the following principles: To encourage broadband deployment and preserve and promote the open and interconnected nature of the public Internet, Consumers are entitled to access the lawful Internet content of their choice; Consumers are entitled to run applications and use services of their choice, subject to

7670-484: The FCC found that it placed many stations too close to each other, resulting in interference. At the same time, it became clear that the designated VHF channels, 2 through 13, were inadequate for nationwide television service. As a result, the FCC stopped giving out construction permits for new licenses in October 1948, under the direction of Chairman Rosel H. Hyde . Most expected this "Freeze" to last six months, but as

7800-587: The FCC in the newly created post of associate general counsel/chief diversity officer. Numerous controversies have surrounded the city of license concept as the internet has made it possible to broadcast a single signal to every owned station in the nation at once, particularly when Clear Channel, now IHeartMedia , became the largest FM broadcasting corporation in the US after the Telecommunications Act of 1996 became law - owning over 1,200 stations at its peak. As part of its license to buy more radio stations, Clear Channel

7930-437: The FCC indicated that the public largely believed that the severe consolidation of media ownership had resulted in harm to diversity, localism, and competition in media, and was harmful to the public interest. David A. Bray joined the commission in 2013 as chief information officer and quickly announced goals of modernizing the FCC's legacy information technology (IT) systems, citing 200 different systems for only 1750 people

SECTION 60

#1732797171007

8060-403: The FCC said that nearly 55 million Americans did not have access to broadband capable of delivering high-quality voice, data, graphics and video offerings. On February 26, 2015, the FCC reclassified broadband Internet access as a telecommunications service, thus subjecting it to Title II regulation, although several exemptions were also created. The reclassification was done in order to give

8190-534: The FCC was created "for the purpose of the national defense" and "for the purpose of promoting safety of life and property through the use of wire and radio communications." Consistent with the objectives of the act as well as the 1999 Government Performance and Results Act (GPRA), the FCC has identified four goals in its 2018–22 Strategic Plan. They are: Closing the Digital Divide, Promoting Innovation, Protecting Consumers & Public Safety, and Reforming

8320-563: The FCC's Processes. The FCC is directed by five commissioners appointed by the president of the United States and confirmed by the United States Senate for five-year terms, except when filling an unexpired term. The U.S. president designates one of the commissioners to serve as chairman. No more than three commissioners may be members of the same political party . None of them may have a financial interest in any FCC-related business. Commissioners may continue serving until

8450-514: The FCC, which regulated AT&T's long-line charges, but the commission took no action. The result was that financially marginal DuMont was spending as much in long-line charge as CBS or NBC while using only about 10 to 15 percent of the time and mileage of either larger network. The FCC's "Sixth Report & Order" ended the Freeze. It took five years for the US to grow from 108 stations to more than 550. New stations came on line slowly, only five by

8580-460: The Internet, cable services and wireless services has raised questions whether new legislative initiatives are needed as to competition in what has come to be called 'broadband' services. Congress has monitored developments but as of 2009 has not undertaken a major revision of applicable regulation. The Local Community Radio Act in the 111th Congress has gotten out of committee and will go before

8710-641: The Sentinel Square III building in northeast Washington, D.C. Prior to moving to its new headquarters in October 2020, the FCC leased space in the Portals building in southwest Washington, D.C. Construction of the Portals building was scheduled to begin on March 1, 1996. In January 1996, the General Services Administration signed a lease with the building's owners, agreeing to let the FCC lease 450,000 sq ft (42,000 m ) of space in Portals for 20 years, at

8840-464: The T568A and T568B conventions have largely displaced RJ25 and RJ61 for telephones with more than two lines. The 8 position 8 contact ( 8P8C ) connector is a modular connector commonly used to terminate twisted pair and multi-conductor flat cable . These connectors are commonly used for Ethernet over twisted pair , registered jacks and other telephone applications, RS-232 serial communication using

8970-492: The United States accelerated an already ongoing shift in the FCC towards a decidedly more market-oriented stance. A number of regulations felt to be outdated were removed, most controversially the Fairness Doctrine in 1987. In terms of indecency fines, there was no action taken by the FCC on the case FCC v. Pacifica until 1987, about ten years after the landmark United States Supreme Court decision that defined

9100-553: The United States. The FCC maintains jurisdiction over the areas of broadband access , fair competition , radio frequency use, media responsibility, public safety, and homeland security . The FCC was formed by the Communications Act of 1934 to replace the radio regulation functions of the previous Federal Radio Commission . The FCC took over wire communication regulation from the Interstate Commerce Commission . The FCC's mandated jurisdiction covers

9230-409: The additional connectors of TAE (E, W, a2, b2) and may feature non-RJ standard sockets that can be connected directly to TAE plugs. Further, flat DIN 47100 cables typically place the wires in ascending order. When used directly with 6P4C plugs, the color coding may be undetermined. In the powered version of the RJ11 interface, pins 2 and 5 (black and yellow) may carry low-voltage AC or DC power. While

9360-591: The allocation of channels to the emerging UHF technology and the eagerly awaited possibilities of color television were debated, the FCC's re-allocation map of stations did not come until April 1952, with July 1, 1952, as the official beginning of licensing new stations. Other FCC actions hurt the fledgling DuMont and ABC networks. American Telephone and Telegraph (AT&T) forced television coaxial cable users to rent additional radio long lines , discriminating against DuMont, which had no radio network operation. DuMont and ABC protested AT&T's television policies to

9490-438: The appointment of their replacements. However, they may not serve beyond the end of the next session of Congress following term expiration. In practice, this means that commissioners may serve up to 1 + 1 ⁄ 2 years beyond the official term expiration listed above if no replacement is appointed. This would end on the date that Congress adjourns its annual session, generally no later than noon on January 3. The FCC

9620-933: The basis for the modular molded-plastic connectors that became commonplace for telephone cords by the 1980s. In 1976, these connectors were standardized nationally in the United States by the Registration Interface program of the Federal Communications Commission (FCC), which designated a series of Registered Jack (RJ) specifications for interconnection of customer-premises equipment to the PSTN. Modular connectors have gender : plugs are considered to be male , while jacks or sockets are considered to be female . Plugs are used to terminate cables and cords, while jacks are used for fixed locations on surfaces of walls, panels, and equipment. Other than telephone extension cables, cables with

9750-518: The best-known applications of modular connectors are for telephone and Ethernet . Accordingly, various electronic interface specifications exist for applications using modular connectors, which prescribe physical characteristics and assign electrical signals to their contacts. Modular connectors are often referred to as modular phone jack and plug , RJ connector , and Western jack and plug . The term modular connector arose from its original use in modular wiring components of telephone equipment by

9880-572: The book value of AT&T by approximately 70%. The FCC initially exempted "information services" such as broadband Internet access from regulation under Title II. The FCC held that information services were distinct from telecommunications services that are subject to common carrier regulation. However, Section 706 of the Telecommunications Act of 1996 required the FCC to help accelerate deployment of "advanced telecommunications capability" which included high-quality voice, data, graphics, and video, and to regularly assess its availability. In August 2015,

10010-509: The cable opening, with prong facing downward, the pins are numbered 1–6, left to right: Some telephones such as the Western Electric Princess and Trimline telephone models require additional power (~6 V AC) for operation of the incandescent dial light. This power is delivered to the telephone set from a transformer by the second wire pair (pins 2 and 5) of the 6P4C connector. RJ21 is a registered jack standard using

10140-444: The commission in 1934 comprised the following seven members: The complete list of commissioners is available on the FCC website. Frieda B. Hennock (D-NY) was the first female commissioner of the FCC in 1948. The FCC regulates broadcast stations, repeater stations as well as commercial broadcasting operators who operate and repair certain radiotelephone , radio and television stations. Broadcast licenses are to be renewed if

10270-426: The connector tab side down with the opening for the cable facing the viewer. However, with German domestic telephone equipment, and that in some neighboring countries, 6P4C plugs and sockets are typically only used to connect the telephone cord to the phone base unit, whereas the mechanically different TAE connector is used at the other end to connect to a service provider interface. Older base units may accommodate

10400-468: The contacts are metal spring wires angled away from the insertion interface. When the plug is mated with the jack, the contacts meet and create an electrical connection. The spring force of the jack contacts ensures a good interface. Although commonly referred to as RJ45 in the context of Ethernet and category 5 cables , RJ45 originally referred to a specific wiring configuration of an 8P8C connector. The original telephone-system-standard RJ45 plug has

10530-414: The conversion, Congress established a federally sponsored DTV Converter Box Coupon Program for two free converters per household. The FCC regulates telecommunications services under Title II of the Communications Act of 1934. Title II imposes common carrier regulation under which carriers offering their services to the general public must provide services to all customers and may not discriminate based on

10660-422: The different number of contacts (two, four and six respectively) allowing connections for one, two, or three telephone lines respectively. Cords connecting to an RJ11 interface require a 6P2C connector. Nevertheless, cords sold as RJ11 often use 6P4C connectors (six position, four conductor) with four wires. Two of the six possible contact positions connect tip and ring, and the other two conductors are unused. RJ11

10790-421: The end of November 1952. The Sixth Report and Order required some existing television stations to change channels, but only a few existing VHF stations were required to move to UHF, and a handful of VHF channels were deleted altogether in smaller media markets like Peoria , Fresno , Bakersfield and Fort Wayne, Indiana to create markets which were UHF "islands." The report also set aside a number of channels for

10920-489: The end of the digital television transition. After delaying the original deadlines of 2006, 2008, and eventually February 17, 2009, on concerns about elderly and rural folk, on June 12, 2009, all full-power analog terrestrial TV licenses in the U.S. were terminated as part of the DTV transition , leaving terrestrial television available only from digital channels and a few low-power LPTV stations. To help U.S. consumers through

11050-413: The female physical connector ( modular connector ) and specific wiring patterns, but the term is often used loosely to refer to modular connectors regardless of wiring, gender, or use, commonly for telephone line connections, but also for Ethernet over twisted pair , resulting in confusion over the various connection standards and applications. For example, the six-position physical connector, plug and jack,

11180-423: The fine ten times over the previous maximum of $ 32,500 per violation. The FCC has established rules limiting the national share of media ownership of broadcast radio or television stations. It has also established cross-ownership rules limiting ownership of a newspaper and broadcast station in the same market, in order to ensure a diversity of viewpoints in each market and serve the needs of each local market. In

11310-598: The first post-Freeze construction permits. KFEL (now KWGN-TV )'s first regular telecast was on July 21, 1952. In 1996, Congress enacted the Telecommunications Act of 1996 , in the wake of the breakup of AT&T resulting from the U.S. Department of Justice's antitrust suit against AT&T. The legislation attempted to create more competition in local telephone service by requiring Incumbent Local Exchange Carriers to provide access to their facilities for Competitive Local Exchange Carriers . This policy has thus far had limited success and much criticism. The development of

11440-419: The functions of its Tx and Rx wire pairs. Pin numbering on plug face. Connected pins on plug and jack have the same number. Two types of 8P8C plugs and crimping tools for installing the plug onto a cable are commonly available: Western Electric/Stewart Stamping (WE/SS) and Tyco/AMP. While the two types are similar, the tooling and plug types cannot be interchanged. WE/SS compatible plugs are available from

11570-435: The house floor with bi-partisan support, and unanimous support of the FCC. By passing the Telecommunications Act of 1996, Congress also eliminated the cap on the number of radio stations any one entity could own nationwide and also substantially loosened local radio station ownership restrictions. Substantial radio consolidation followed. Restrictions on ownership of television stations were also loosened. Public comments to

11700-446: The identity of the customer or the content of the communication. This is similar to and adapted from the regulation of transportation providers (railroad, airline, shipping, etc.) and some public utilities. Wireless carriers providing telecommunications services are also generally subject to Title II regulation except as exempted by the FCC. The FCC regulates interstate telephone services under Title II. The Telecommunications Act of 1996

11830-430: The insulation and go straight through to contact multiple wire strands. Some modular connectors are indexed , meaning their dimensions are intentionally non-standard, preventing connections with connectors of standard dimensions. The means of indexing may be non-standard cross-sectional dimensions or shapes, retention mechanism dimensions or configuration. For example, a Modified Modular Jack using an offset latching tab

11960-505: The jacks in the house. Structured cabling networks adhering to ANSI/TIA-568 , ISO/IEC 11801 (or ISO/IEC 15018 for home networks) are widely used for both computer networking and analog telephony. These standards specify the T568A or T568B wiring arrangements compatible with Ethernet . The 8P8C jack used by structured cabling physically accepts the 6-position connector used by RJ11, RJ14 and RJ25. Only RJ11 and RJ14 have full electrical compatibility because Ethernet-compatible pin-outs split

12090-489: The keyboard to the main computer housing. The connector provides power to the keyboard on the outer two contacts and receives data signals on the inner pair. The cable between the computer and the keyboard is a coiled cord with an appearance very similar to a telephone handset cable. The connector on the Amiga 1000 uses crossover wiring, similar to a telephone handset. The connector wiring on the Apple computers, however, requires

12220-527: The largest U.S. city without a TV station by 1952. Senator Edwin Johnson (D-Colorado), chair of the Senate's Interstate and Foreign Commerce Committee , had made it his personal mission to make Denver the first post-Freeze station. The senator had pressured the FCC, and proved ultimately successful as the first new station (a VHF station) came on-line a remarkable ten days after the commission formally announced

12350-465: The line to be broken to insert automatic dialing equipment, including intrusion alarm panels. The EIA /TIA-561 standard describes the use of 8P8C connectors for RS-232 serial interfaces. This application is common as a console interface for network equipment , such as switches , routers , and headless computers . 8P8C modular connectors are also commonly used as a microphone connectors for PMR , LMR , and amateur radio transceivers. Frequently

12480-659: The mid-1960s for the plug-in handset and line cords of the Trimline telephone. Driven by demand for multiple sets in residences with various lengths of cords, the Bell System introduced customer-connectable part kits and telephones, sold through PhoneCenter stores in the early 1970s. For this purpose, Illinois Bell started installing modular telephone sets on a limited scale in June 1972. The patents by Edwin C. Hardesty and coworkers, US 3699498   (1972) and US 3860316   (1975), followed by other improvements, were

12610-508: The modular connectors and their wiring as Universal Service Order Codes (USOC), which were the only standards at the time. Large customers of telephone services commonly use the USOC to specify the interconnection type and, when necessary, pin assignments, when placing service orders with a network provider. When the U.S. telephone industry was reformed to foster competition in the 1980s, the connection specifications became federal law, ordered by

12740-492: The move was done to improve the FCC's "coordination across the federal government" and to "support the 21st-century satellite industry." The decision to establish the Space Bureau was reportedly done to improve the agency's capacity to regulate Satellite Internet access . The new bureau officially launched on April 11, 2023. The commissioners of the FCC are: The initial group of FCC commissioners after establishment of

12870-709: The name RJ45 . The shape and dimensions of an 8P8C modular connector are specified for US telephone applications by the Administrative Council for Terminal Attachment (ACTA) in national standard ANSI /TIA-1096-A and international standard ISO-8877. This standard does not use the short term 8P8C and covers more than just 8P8C modular connectors, but the 8P8C modular connector type is the eight-position connector type described therein, with eight contacts installed. For data communication applications ( LAN , structured cabling ), International Standard IEC 60603 specifies in parts 7-1, 7-2, 7-4, 7-5, and 7-7 not only

13000-503: The negative effects of media concentration and consolidation on racial-ethnic diversity in staffing and programming. At these Latino town hall meetings, the issue of the FCC's lax monitoring of obscene and pornographic material in Spanish-language radio and the lack of racial and national-origin diversity among Latino staff in Spanish-language television were other major themes. President Barack Obama appointed Mark Lloyd to

13130-482: The newly emerging field of educational television , which hindered struggling ABC and DuMont 's quest for affiliates in the more desirable markets where VHF channels were reserved for non-commercial use. The Sixth Report and Order also provided for the "intermixture" of VHF and UHF channels in most markets; UHF transmitters in the 1950s were not yet powerful enough, nor receivers sensitive enough (if they included UHF tuners at all - they were not formally required until

13260-479: The original 10BASE-T twisted-pair wiring version of Ethernet was developed, this modular connector was chosen as the basis for IEEE 802.3i-1990. Modular connector A modular connector is a type of electrical connector for cords and cables of electronic devices and appliances, such as in computer networking , telecommunication equipment, and audio headsets. Modular connectors were originally developed for use on specific Bell System telephone sets in

13390-499: The outer pairs). These interfaces use the same six-position modular connector body but have different numbers of pins installed. RJ11 is a physical interface often used for terminating single telephone lines. RJ14 is similar, but for two lines, and RJ25 is for three lines. RJ61 is a similar registered jack for four lines, but uses an 8P8C connector. Cables sold as RJ11 often actually use 6P4C connectors (six positions, four contacts) and RJ14 wiring – four wires running to

13520-477: The outermost contacts in the jack are forcibly deformed. Special modular plugs have been manufactured (for example, the Siemon UP-2468 ) which have extra slots beyond their standard contacts, to accommodate the wider jack's outermost contacts without damage. These special plug connectors can be visually identified by carefully looking for the extra slots molded into the plug. The molded plastic bodies of

13650-584: The passage of the Communications Act of 1934, that the inherent scarcity of radio spectrum allows the government to impose some types of content restrictions on broadcast license holders notwithstanding the First Amendment. Cable and satellite providers are also subject to some content regulations under Title VI of the Communications Act such as the prohibition on obscenity, although the limitations are not as restrictive compared to broadcast stations. The 1981 inauguration of Ronald Reagan as President of

13780-463: The pinout is different, usually mirrored (i.e. what would be pins 1 to 8 in the ANSI/TIA-568 standard might be pins 8 to 1 in the radio and its manual). Federal Communications Commission The Federal Communications Commission ( FCC ) is an independent agency of the United States government that regulates communications by radio , television , wire, satellite , and cable across

13910-536: The position and contact quantities with either an x ( 6x2 ) or a slash ( 6/2 ). When not installed, contacts are usually omitted from the outer positions inward, such that the number of contacts is almost always even. The connector body positions with omitted or unconnected contacts are unused for the electrical connection but ensure that the plug fits correctly. For instance, inexpensive telephone cords often have connectors with six positions and four contacts, to which are attached just two wires, carrying only line 1 from

14040-473: The power of the FCC over indecent material as applied to broadcasting. After the 1990s had passed, the FCC began to increase its censorship and enforcement of indecency regulations in the early 2000s to include a response to the Janet Jackson " wardrobe malfunction " that occurred during the halftime show of Super Bowl XXXVIII . Then on June 15, 2006, President George W. Bush signed into law

14170-399: The protective boot before the modular plug is crimped. Modular connectors are designated using two numbers that represent the maximum number of contact positions and the number of installed contacts, with each number followed by P and C , respectively. For example, 6P2C is a connector having six positions and two installed contacts. Alternate designations omit the letters while separating

14300-433: The publication of TIA-968-B, the connector descriptions have been moved to TIA-1096-A. A registered jack name, such as RJ11, still identifies both the physical connectors and the wiring (pinout) for each application. The most widely implemented registered jack in telecommunications is the RJ11. This is a modular connector wired for one telephone line, using the center two contacts of six available positions. This configuration

14430-454: The regular 8P8C modular connector type is often labeled RJ45 because the registered jack standard of the similar name RJ45S specified a similar, but modified, 8P8C modular connector. Similarly, various six-position modular connectors may be called RJ11 . Likewise, the 4P4C connector is sometimes called RJ9 or RJ22 though no such official designations exist. The first types of small modular telephone connectors were created by AT&T in

14560-445: The same colors as the matching ring but switches the thickness of the primary and secondary colored stripes. Since the sets are ordered, an orange (color 2 in its set) with a yellow (color 4) is the color scheme for the 4·5 + 2 − 5 = 17th pair of wires. If the yellow is the more prominent, thicker stripe, then the wire is a tip conductor connecting to the pin numbered 25 + the pair #, which is pin 42 in this case. Ring conductors connect to

14690-447: The same connector, either T568A or T568B . RJ48, T568A, and T568B are all designed to keep both wires of each pair close together. The flat eight-conductor silver-satin cable conventionally used with four-line analog telephones and RJ61 jacks is also unsuitable for use with high-speed data. Twisted pair cabling is required for data applications. Twisted-pair patch cable typically used with common Ethernet and other data network standards

14820-412: The same physical dimensions but also high-frequency performance requirements for shielded and unshielded versions of this connector for carrying frequencies up to 100, 250 and 600  MHz . 8P8C connectors are frequently terminated using the T568A or T568B assignments that are defined in ANSI/TIA-568. The drawings to the right show that the copper connections and pairing are the same, the only difference

14950-551: The same pin number as the pair number. A conventional enumeration of wire color pairs then begins blue (and white), orange (and white), green (and white) and brown (and white), which subsumes a color-coding convention used in cables of 4 or fewer pairs (8 wires or less) with 8P and 6P connectors. Dual 50-pin ribbon connectors are often used on punch blocks to create a breakout box for private branch exchange (PBX) and other key telephone systems . The RJ45S, an obsolete standard jack once specified for modem or data interfaces, has

15080-960: The second half of 2006, groups such as the National Hispanic Media Coalition, the National Latino Media Council, the National Association of Hispanic Journalists, the National Institute for Latino Policy , the League of United Latin American Citizens (LULAC) and others held town hall meetings in California, New York and Texas on media diversity as its effects Latinos and minority communities. They documented widespread and deeply felt community concerns about

15210-578: The service provider. In the Bell System , following the Communications Act of 1934 , the telephone companies owned all telecommunications equipment and they did not allow interconnection of third-party equipment. Telephones were generally hardwired, but may have been installed with Bell System connectors to permit portability. The legal case Hush-A-Phone v. United States (1956) and the Federal Communications Commission 's (FCC) Carterfone (1968) decision brought changes to this policy, and required

15340-405: The special plugs may also be colored with a light blueish tinge, to aid in quick recognition. The special plugs are preferred for test equipment and adapters, which may be rapidly connected to a large number of corresponding connectors in quick succession for testing purposes. The use of the special plugs avoids inadvertent damage to the equipment under test, even when a narrower plug is inserted into

15470-582: The standards published by the engineering committees of the Telecommunications Industry Association (TIA). ACTA and TIA jointly published the standard TIA/EIA-IS-968, replacing the CFR information. TIA-968-A, the current version of that standard, details the physical aspects of modular connectors, but not the wiring. Instead, TIA-968-A incorporates the standard T1.TR5-1999, "Network and Customer Installation Interface Connector Wiring Configuration Catalog", by reference. With

15600-435: The station meets the "public interest, convenience, or necessity". The FCC's enforcement powers include fines and broadcast license revocation (see FCC MB Docket 04-232). Burden of proof would be on the complainant in a petition to deny. The FCC first promulgated rules for cable television in 1965, with cable and satellite television now regulated by the FCC under Title VI of the Communications Act. Congress added Title VI in

15730-421: The tab by pressing it against the plug body. The standard orientation for installing a jack in a vertical surface is with the tab down. The modular plug is often installed with a boot , a plastic covering over the tab and body, to prevent the latching tab from hooking into other cords or edges, which may cause excessive bending or breaking of the tab. Such snagless cords are usually constructed by installing

15860-418: The telephone line on pins 3 and 4 (red and green) supplies enough power for most telephone terminals, old telephone terminals with incandescent lights, such as the Western Electric Princess and Trimline telephones , need more power than the phone line can supply. Typically, the power on pins 2 and 5 is supplied by an AC adapter plugged into a nearby power outlet which potentially even supplies power to all of

15990-454: The third pair of RJ25 across two separate cable pairs, rendering that pair unusable by an analog phone. Both the third and fourth pairs of RJ61 are similarly split. The incompatible T568A and T568B layouts were necessary to preserve the electrical properties of the third and fourth pairs for Ethernet, which operates at much higher frequencies than analog telephony. Because of these incompatibilities, and because RJ25 and RJ61 were never very common,

16120-591: The tool is operated, the die compresses around the 8P8C plug. As the die compresses, these teeth force the plug contacts into the conductors of the cable being terminated. The crimper may also permanently deform part of the plastic plug body in such a way that it grips the outer sheath of the cable for secure fastening and strain relief . These actions permanently attach the plug to the cable. The contact assignments ( pinout ) of modular connectors vary by application. Telephone network connections are standardized by registered jack designations, and Ethernet over twisted pair

16250-537: The two contacts are numbered 3 and 4. Modular connectors are manufactured in four sizes, with four, six, eight, and ten positions. The insulating plastic bodies of 4P and 6P connectors have different widths, whereas 8P or 10P connectors share an even larger body width. Internally, the contacts in the plugs have sharp prongs that, when crimped , displace the wire insulation and connect with the conductors inside—a mechanism known as insulation displacement . Cables have either solid or stranded ( tinsel wire ) conductors, and

16380-482: The width is dependent on the number of pin positions. However, not all plugs from all manufacturers have this capability, and some jack manufacturers warn that their jacks are not designed to accept smaller plugs without damage. If an inserted plug lacks slots to accommodate the jack's contacts at the outermost extremes, it may permanently deform those outermost contacts of an incompatible jack. Excessive resistance may be encountered when inserting an incompatible plug, as

16510-442: Was a prominent manufacturer of these at one time. A cable color scheme, known as even-count color code , is determined for 25 pairs of conductors as follows: For each ring, the primary, more prominent color is chosen from the set blue, orange, green, brown, and slate, in that order, and the secondary, thinner stripe color from the set of white, red, black, yellow, and violet colors, in that order. The tip conductor color scheme uses

16640-461: Was developed by Digital Equipment Corporation to prevent accidental interchange of data and telephone cables. The dimensions of modular connectors are such that a narrower plug can be inserted into a wider jack that has more positions than the plug, leaving the jack's outermost contacts unconnected. The height of the plug's insertion area is 0.260 inches (6.60 mm) and the contacts are 0.040 inches (1.02 mm) apart (contact pitch), so

16770-441: Was forced to divest all TV stations. To facilitate the adoption of digital television, the FCC issued a second digital TV (DTV) channel to each holder of an analog TV station license. All stations were required to buy and install all new equipment ( transmitters , TV antennas, and even entirely new broadcast towers ), and operate for years on both channels. Each licensee was required to return one of their two channels following

16900-471: Was the first major legislative reform since the 1934 act and took several steps to de-regulate the telephone market and promote competition in both the local and long-distance marketplace. The important relationship of the FCC and the American Telephone and Telegraph (AT&T) Company evolved over the decades. For many years, the FCC and state officials agreed to regulate the telephone system as

#6993