A warhead is the section of a device that contains the explosive agent or toxic (biological, chemical, or nuclear) material that is delivered by a missile , rocket , torpedo , or bomb .
71-889: Types of warheads include: Often, a biological or chemical warhead will use an explosive charge for rapid dispersal. Explosive warheads contain detonators to trigger the explosion. Types of detonators include: Detonator A detonator is a device used to make an explosive or explosive device explode. Detonators come in a variety of types, depending on how they are initiated (chemically, mechanically, or electrically) and details of their inner working, which often involve several stages. Types of detonators include non-electric and electric. Non-electric detonators are typically stab or pyrotechnic while electric are typically "hot wire" (low voltage), exploding bridge wire (high voltage) or explosive foil (very high voltage). The original electric detonators invented in 1875 independently by Julius Smith and Perry Gardiner used mercury fulminate as
142-420: A chemically pure compound, such as nitroglycerin , or a mixture of a fuel and an oxidizer , such as black powder or grain dust and air. Some chemical compounds are unstable in that, when shocked, they react, possibly to the point of detonation. Each molecule of the compound dissociates into two or more new molecules (generally gases) with the release of energy. The above compositions may describe most of
213-414: A commercial blasting cap consisting of a paper tube full of black powder , with wires leading in both sides and wadding sealing up the ends. The two wires came close but did not touch, so a large electric spark discharge between the two wires would fire the cap. In 1832, a hot wire detonator was produced by American chemist Robert Hare , although attempts along similar lines had earlier been attempted by
284-439: A dedicated programming device. Wireless electronic detonators are beginning to be available in the civil mining market. Encrypted radio signals are used to communicate the blast signal to each detonator at the correct time. While currently expensive, wireless detonators can enable new mining techniques as multiple blasts can be loaded at once and fired in sequence without putting humans in harm's way. A number 8 test blasting cap
355-634: A degree of water resistance. Explosives based on ammonium nitrate have little or no water resistance as ammonium nitrate is highly soluble in water and is hygroscopic. Many explosives are toxic to some extent. Manufacturing inputs can also be organic compounds or hazardous materials that require special handling due to risks (such as carcinogens ). The decomposition products, residual solids, or gases of some explosives can be toxic, whereas others are harmless, such as carbon dioxide and water. Examples of harmful by-products are: "Green explosives" seek to reduce environment and health impacts. An example of such
426-448: A few milliseconds to fire, as the bridgewire heats up and heats the explosive to the point of detonation. Exploding bridgewire or EBW detonators use a higher voltage electric charge and a very thin bridgewire, .04 inch long, .0016 diameter, (1 mm long, 0.04 mm diameter). Instead of heating up the explosive, the EBW detonator wire is heated so quickly by the high firing current that
497-567: A fuse, to detonate nitroglycerin. In 1868, Henry Julius Smith of Boston introduced a cap that combined a spark gap ignitor and mercury fulminate, the first electric cap able to detonate dynamite. In 1875, Smith—and then in 1887, Perry G. Gardner of North Adams, Massachusetts—developed electric detonators that combined a hot wire detonator with mercury fulminate explosive. These were the first generally modern type blasting caps. Modern caps use different explosives and separate primary and secondary explosive charges, but are generally very similar to
568-433: A number of more exotic explosive materials, and exotic methods of causing explosions. Examples include nuclear explosives , and abruptly heating a substance to a plasma state with a high-intensity laser or electric arc . Laser- and arc-heating are used in laser detonators, exploding-bridgewire detonators , and exploding foil initiators , where a shock wave and then detonation in conventional chemical explosive material
639-685: A practical measure, primary explosives are sufficiently sensitive that they can be reliably initiated with a blow from a hammer; however, PETN can also usually be initiated in this manner, so this is only a very broad guideline. Additionally, several compounds, such as nitrogen triiodide , are so sensitive that they cannot even be handled without detonating. Nitrogen triiodide is so sensitive that it can be reliably detonated by exposure to alpha radiation . Primary explosives are often used in detonators or to trigger larger charges of less sensitive secondary explosives . Primary explosives are commonly used in blasting caps and percussion caps to translate
710-399: A reaction to be classified as a detonation as opposed to just a deflagration, the propagation of the reaction shockwave through the material being tested must be faster than the speed of sound through that material. The speed of sound through a liquid or solid material is usually orders of magnitude faster than the speed of sound through air or other gases. Traditional explosives mechanics
781-540: A small amount of TNT or tetryl in military detonators and PETN in commercial detonators. The first blasting cap or detonator was demonstrated in 1745 when British physician and apothecary William Watson showed that the electric spark of a friction machine could ignite black powder, by way of igniting a flammable substance mixed in with the black powder. In 1750, Benjamin Franklin in Philadelphia made
SECTION 10
#1732790760540852-435: A small pyrotechnic delay element, up to a few hundred milliseconds, before the cap fires. Match type blasting caps use an electric match (insulating sheet with electrodes on both sides, a thin bridgewire soldered across the sides, all dipped in ignition and output mixes) to initiate the primary explosive, rather than direct contact between the bridgewire and the primary explosive. The match can be manufactured separately from
923-735: A smaller number are manufactured specifically for the purpose of being used as explosives. The remainder are too dangerous, sensitive, toxic, expensive, unstable, or prone to decomposition or degradation over short time spans. In contrast, some materials are merely combustible or flammable if they burn without exploding. The distinction, however, is not very clear. Certain materials—dusts, powders, gases, or volatile organic liquids—may be simply combustible or flammable under ordinary conditions, but become explosive in specific situations or forms, such as dispersed airborne clouds , or confinement or sudden release . Early thermal weapons , such as Greek fire , have existed since ancient times. At its roots,
994-618: A thermodynamically favorable process in addition to one that propagates very rapidly. Thus, explosives are substances that contain a large amount of energy stored in chemical bonds . The energetic stability of the gaseous products and hence their generation comes from the formation of strongly bonded species like carbon monoxide, carbon dioxide, and nitrogen gas, which contain strong double and triple bonds having bond strengths of nearly 1 MJ/mole. Consequently, most commercial explosives are organic compounds containing –NO 2 , –ONO 2 and –NHNO 2 groups that, when detonated, release gases like
1065-709: Is mining . Whether the mine is on the surface or is buried underground, the detonation or deflagration of either a high or low explosive in a confined space can be used to liberate a fairly specific sub-volume of a brittle material (rock) in a much larger volume of the same or similar material. The mining industry tends to use nitrate-based explosives such as emulsions of fuel oil and ammonium nitrate solutions, mixtures of ammonium nitrate prills (fertilizer pellets) and fuel oil ( ANFO ) and gelatinous suspensions or slurries of ammonium nitrate and combustible fuels. In materials science and engineering, explosives are used in cladding ( explosion welding ). A thin plate of some material
1136-427: Is a pure substance ( molecule ) that in a chemical reaction can contribute some atoms of one or more oxidizing elements, in which the fuel component of the explosive burns. On the simplest level, the oxidizer may itself be an oxidizing element , such as gaseous or liquid oxygen . The availability and cost of explosives are determined by the availability of the raw materials and the cost, complexity, and safety of
1207-402: Is an important consideration in selecting an explosive for a particular purpose. The explosive in an armor-piercing projectile must be relatively insensitive, or the shock of impact would cause it to detonate before it penetrated to the point desired. The explosive lenses around nuclear charges are also designed to be highly insensitive, to minimize the risk of accidental detonation. The index of
1278-440: Is an important element influencing the yield of the energy transmitted for both atmospheric over-pressure and ground acceleration. By definition, a "low explosive", such as black powder, or smokeless gunpowder has a burn rate of 171–631 m/s. In contrast, a "high explosive", whether a primary, such as detonating cord , or a secondary, such as TNT or C-4, has a significantly higher burn rate about 6900–8092 m/s. Stability
1349-520: Is based on the shock-sensitive rapid oxidation of carbon and hydrogen to carbon dioxide, carbon monoxide and water in the form of steam. Nitrates typically provide the required oxygen to burn the carbon and hydrogen fuel. High explosives tend to have the oxygen, carbon and hydrogen contained in one organic molecule, and less sensitive explosives like ANFO are combinations of fuel (carbon and hydrogen fuel oil) and ammonium nitrate . A sensitizer such as powdered aluminum may be added to an explosive to increase
1420-443: Is created by laser- or electric-arc heating. Laser and electric energy are not currently used in practice to generate most of the required energy, but only to initiate reactions. To determine the suitability of an explosive substance for a particular use, its physical properties must first be known. The usefulness of an explosive can only be appreciated when the properties and the factors affecting them are fully understood. Some of
1491-452: Is evaluated by a tailored series of tests to assess the material for its intended use. Of the tests listed below, cylinder expansion and air-blast tests are common to most testing programs, and the others support specific applications. In addition to strength, explosives display a second characteristic, which is their shattering effect or brisance (from the French meaning to "break"). Brisance
SECTION 20
#17327907605401562-472: Is important in determining the effectiveness of an explosion in fragmenting shells, bomb casings, and grenades . The rapidity with which an explosive reaches its peak pressure ( power ) is a measure of its brisance. Brisance values are primarily employed in France and Russia. The sand crush test is commonly employed to determine the relative brisance in comparison to TNT. No test is capable of directly comparing
1633-410: Is one containing 2 grams of a mixture of 80 percent mercury fulminate and 20 percent potassium chlorate, or a blasting cap of equivalent strength. An equivalent strength cap comprises 0.40-0.45 grams of PETN base charge pressed in an aluminum shell with bottom thickness not to exceed to 0.03 of an inch, to a specific gravity of not less than 1.4 g/cc, and primed with standard weights of primer depending on
1704-400: Is placed atop a thick layer of a different material, both layers typically of metal. Atop the thin layer is placed an explosive. At one end of the layer of explosive, the explosion is initiated. The two metallic layers are forced together at high speed and with great force. The explosion spreads from the initiation site throughout the explosive. Ideally, this produces a metallurgical bond between
1775-441: Is required, specifically in the implosion charges in nuclear weapons , exploding-bridgewire detonators are employed. The initial shock wave is created by vaporizing a length of a thin wire by an electric discharge . A new development is a slapper detonator , which uses thin plates accelerated by an electrically exploded wire or foil to deliver the initial shock. It is in use in some modern weapons systems. A variant of this concept
1846-817: Is still used sometimes, but very rarely due to its high price. It is possible to construct a Non Primary Explosive Detonator (NPED) in which the primary explosive is replaced by a flammable but non-explosive mixture that propagates a shock wave along a tube into the secondary explosive. NPEDs are harder to accidentally trigger by shock and can avoid the use of lead. As secondary "base" or "output" explosive, TNT or tetryl are typically found in military detonators and PETN in commercial detonators. While detonators make explosive handling safer, they are hazardous to handle since, despite their small size, they contain enough explosive to injure people; untrained personnel might not recognize them as explosives or wrongly deem them not dangerous due to their appearance and handle them without
1917-473: Is the ability of an explosive to be stored without deterioration . The following factors affect the stability of an explosive: The term power or performance as applied to an explosive refers to its ability to do work. In practice it is defined as the explosive's ability to accomplish what is intended in the way of energy delivery (i.e., fragment projection, air blast, high-velocity jet, underwater shock and bubble energy, etc.). Explosive power or performance
1988-411: Is the lead-free primary explosive copper(I) 5-nitrotetrazolate, an alternative to lead azide . Explosive material may be incorporated in the explosive train of a device or system. An example is a pyrotechnic lead igniting a booster, which causes the main charge to detonate. The most widely used explosives are condensed liquids or solids converted to gaseous products by explosive chemical reactions and
2059-437: Is used in mining operations, when the foil is exploded by a laser pulse delivered to the foil by optical fiber . A non-electric detonator is a shock tube detonator designed to initiate explosions, generally for the purpose of demolition of buildings and for use in the blasting of rock in mines and quarries. Instead of electric wires, a hollow plastic tube delivers the firing impulse to the detonator, making it immune to most of
2130-407: Is used to describe an explosive phenomenon whereby the decomposition is propagated by a shock wave traversing the explosive material at speeds greater than the speed of sound within the substance. The shock front is capable of passing through the high explosive material at supersonic speeds — typically thousands of metres per second. In addition to chemical explosives, there are
2201-488: The primary explosive . Around the turn of the century performance was enhanced in the Smith-Gardiner blasting cap by the addition of 10-20% potassium chlorate . This compound was superseded by others: lead azide , lead styphnate , some aluminium , or other materials such as DDNP ( diazo dinitro phenol ) to reduce the amount of lead emitted into the atmosphere by mining and quarrying operations. They also often use
Warhead - Misplaced Pages Continue
2272-597: The Gardner and Smith caps. Smith also invented the first satisfactory portable power supply for igniting blasting caps : a high-voltage magneto that was driven by a rack and pinion , which in turn was driven by a T-handle that was pushed downwards. Electric match caps were developed in the early 1900s in Germany, and spread to the US in the 1950s when ICI International purchased Atlas Powder Co. These match caps have become
2343-483: The HE or Direct Optical Initiation (DOI); (2) rapid heating of a thin film in contact with a HE; and (3) ablating a thin metal foil to produce a high velocity flyer plate that impacts the HE (laser flyer). Secondary explosive An explosive (or explosive material ) is a reactive substance that contains a great amount of potential energy that can produce an explosion if released suddenly, usually accompanied by
2414-493: The Italians Volta and Cavallo. Hare constructed his blasting cap by passing a multistrand wire through a charge of gunpowder inside a tin tube; he had cut all but one fine strand of the multistrand wire so that the fine strand would serve as the hot bridgewire. When a strong current from a large battery (which he called a "deflagrator" or "calorimotor") was passed through the fine strand, it became incandescent and ignited
2485-547: The Swedish company Nitro Nobel in the 1960s and 1970s, and launched to the demolitions market in 1973. In civil mining, electronic detonators have a better precision for delays. Electronic detonators are designed to provide the precise control necessary to produce accurate and consistent blasting results in a variety of blasting applications in the mining, quarrying, and construction industries. Electronic detonators may be programmed in millisecond or sub-millisecond increments using
2556-413: The aforementioned (e.g., nitroglycerin , TNT , HMX , PETN , nitrocellulose ). An explosive is classified as a low or high explosive according to its rate of combustion : low explosives burn rapidly (or deflagrate ), while high explosives detonate . While these definitions are distinct, the problem of precisely measuring rapid decomposition makes practical classification of explosives difficult. For
2627-479: The bridgewire, but it cannot detonate the initiator explosive without the full high-voltage high-current charge passing through the bridgewire. EBW detonators are used in many civilian applications where radio signals, static electricity, or other electrical hazards might cause accidents with conventional electric detonators. Exploding foil initiators (EFI), also known as Slapper detonators are an improvement on EBW detonators. Slappers, instead of directly using
2698-479: The capacity of an explosive to be initiated into detonation in a sustained manner. It is defined by the power of the detonator which is certain to prime the explosive to a sustained and continuous detonation. Reference is made to the Sellier-Bellot scale that consists of a series of 10 detonators, from n. 1 to n. 10 , each of which corresponds to an increasing charge weight. In practice, most of
2769-407: The charge of gunpowder. In 1863, Alfred Nobel realized that although nitroglycerin could not be detonated by a fuse, it could be detonated by the explosion of a small charge of gunpowder, which in turn was ignited by a fuse. Within a year, he was adding mercury fulminate to the gunpowder charges of his detonators, and by 1867 he was using small copper capsules of mercury fulminate, triggered by
2840-486: The chemical reaction moves faster through the material than the speed of sound ) are said to be "high explosives" and materials that deflagrate are said to be "low explosives". Explosives may also be categorized by their sensitivity . Sensitive materials that can be initiated by a relatively small amount of heat or pressure are primary explosives and materials that are relatively insensitive are secondary or tertiary explosives . A wide variety of chemicals can explode;
2911-425: The choice being determined by the characteristics of the explosive. Dependent upon the method employed, an average density of the loaded charge can be obtained that is within 80–99% of the theoretical maximum density of the explosive. High load density can reduce sensitivity by making the mass more resistant to internal friction . However, if density is increased to the extent that individual crystals are crushed,
Warhead - Misplaced Pages Continue
2982-421: The development of pressure within rounds of ammunition and separation of mixtures into their constituents. Volatility affects the chemical composition of the explosive such that a marked reduction in stability may occur, which results in an increase in the danger of handling. The introduction of water into an explosive is highly undesirable since it reduces the sensitivity, strength, and velocity of detonation of
3053-498: The energy of the detonation. Once detonated, the nitrogen portion of the explosive formulation emerges as nitrogen gas and toxic nitric oxides . The chemical decomposition of an explosive may take years, days, hours, or a fraction of a second. The slower processes of decomposition take place in storage and are of interest only from a stability standpoint. Of more interest are the other two rapid forms besides decomposition: deflagration and detonation. In deflagration, decomposition of
3124-604: The energy released by those reactions. The gaseous products of complete reaction are typically carbon dioxide , steam , and nitrogen . Gaseous volumes computed by the ideal gas law tend to be too large at high pressures characteristic of explosions. Ultimate volume expansion may be estimated at three orders of magnitude, or one liter per gram of explosive. Explosives with an oxygen deficit will generate soot or gases like carbon monoxide and hydrogen , which may react with surrounding materials such as atmospheric oxygen . Attempts to obtain more precise volume estimates must consider
3195-648: The exploding foil to detonate the initiator explosive, use the electrical vaporization of the foil to drive a small circle of insulating material such as PET film or kapton down a circular hole in an additional disc of insulating material. At the far end of that hole is a pellet of high-density secondary explosive. Slapper detonators omit the low-density initiating explosive used in EBW designs and they require much greater energy density than EBW detonators to function, making them inherently safer. Laser initiation of explosives, propellants or pyrotechnics has been attempted in three different ways, (1) direct interaction with
3266-445: The explosive material is propagated by a flame front which moves relatively slowly through the explosive material, i.e. at speeds less than the speed of sound within the substance (which is usually still higher than 340 m/s or 1,220 km/h in most liquid or solid materials) in contrast to detonation, which occurs at speeds greater than the speed of sound. Deflagration is a characteristic of low explosive material. This term
3337-651: The explosive material, but a practical explosive will often include small percentages of other substances. For example, dynamite is a mixture of highly sensitive nitroglycerin with sawdust , powdered silica , or most commonly diatomaceous earth , which act as stabilizers. Plastics and polymers may be added to bind powders of explosive compounds; waxes may be incorporated to make them safer to handle; aluminium powder may be introduced to increase total energy and blast effects. Explosive compounds are also often "alloyed": HMX or RDX powders may be mixed (typically by melt-casting) with TNT to form Octol or Cyclotol . An oxidizer
3408-442: The explosive may become more sensitive. Increased load density also permits the use of more explosive, thereby increasing the power of the warhead . It is possible to compress an explosive beyond a point of sensitivity, known also as dead-pressing , in which the material is no longer capable of being reliably initiated, if at all. Volatility is the readiness with which a substance vaporizes . Excessive volatility often results in
3479-414: The explosive properties of two or more compounds; it is important to examine the data from several such tests (sand crush, trauzl , and so forth) in order to gauge relative brisance. True values for comparison require field experiments. Density of loading refers to the mass of an explosive per unit volume. Several methods of loading are available, including pellet loading, cast loading, and press loading,
3550-409: The explosive. Hygroscopicity is a measure of a material's moisture-absorbing tendencies. Moisture affects explosives adversely by acting as an inert material that absorbs heat when vaporized, and by acting as a solvent medium that can cause undesired chemical reactions. Sensitivity, strength, and velocity of detonation are reduced by inert materials that reduce the continuity of the explosive mass. When
3621-429: The explosives on the market today are sensitive to an n. 8 detonator, where the charge corresponds to 2 grams of mercury fulminate . The velocity with which the reaction process propagates in the mass of the explosive. Most commercial mining explosives have detonation velocities ranging from 1,800 m/s to 8,000 m/s. Today, velocity of detonation can be measured with accuracy. Together with density it
SECTION 50
#17327907605403692-413: The first time in warfare. The Chinese would incorporate explosives fired from bamboo or bronze tubes known as bamboo firecrackers. The Chinese also inserted live rats inside the bamboo firecrackers; when fired toward the enemy, the flaming rats created great psychological ramifications—scaring enemy soldiers away and causing cavalry units to go wild. The first useful explosive stronger than black powder
3763-428: The fuse must be inserted and then crimped into place by crushing the base of the cap around the fuse. If the tool used to crimp the cap is used too close to the explosives, the primary explosive compound can detonate during crimping. A common hazardous practice is crimping caps with one's teeth; an accidental detonation can cause serious injury to the mouth. Fuse type blasting caps are still in active use today. They are
3834-445: The hazards associated with stray electric current. It consists of a small diameter, three-layer plastic tube coated on the innermost wall with a reactive explosive compound, which, when ignited, propagates a low energy signal, similar to a dust explosion. The reaction travels at approximately 6,500 ft/s (2,000 m/s) along the length of the tubing with minimal disturbance outside of the tube. Non-electric detonators were invented by
3905-532: The history of chemical explosives lies in the history of gunpowder . During the Tang dynasty in the 9th century, Taoist Chinese alchemists were eagerly trying to find the elixir of immortality. In the process, they stumbled upon the explosive invention of black powder made from coal, saltpeter, and sulfur in 1044. Gunpowder was the first form of chemical explosives and by 1161, the Chinese were using explosives for
3976-404: The manufacturer. [1] The oldest and simplest type of cap, fuse caps are a metal cylinder, closed at one end. From the open end inwards, there is first an empty space into which a pyrotechnic fuse is inserted and crimped, then a pyrotechnic ignition mix, a primary explosive , and then the main detonating explosive charge. The primary hazard of pyrotechnic blasting caps is that for proper usage,
4047-450: The manufacturing operations. A primary explosive is an explosive that is extremely sensitive to stimuli such as impact , friction , heat , static electricity , or electromagnetic radiation . Some primary explosives are also known as contact explosives . A relatively small amount of energy is required for initiation . As a very general rule, primary explosives are considered to be those compounds that are more sensitive than PETN . As
4118-436: The moisture content evaporates during detonation, cooling occurs, which reduces the temperature of reaction. Stability is also affected by the presence of moisture since moisture promotes decomposition of the explosive and, in addition, causes corrosion of the explosive's metal container. Explosives considerably differ from one another as to their behavior in the presence of water. Gelatin dynamites containing nitroglycerine have
4189-443: The molecule is said to have a zero oxygen balance. The molecule is said to have a positive oxygen balance if it contains more oxygen than is needed and a negative oxygen balance if it contains less oxygen than is needed. The sensitivity, strength , and brisance of an explosive are all somewhat dependent upon oxygen balance and tend to approach their maxima as oxygen balance approaches zero. A chemical explosive may consist of either
4260-457: The more important characteristics are listed below: Sensitivity refers to the ease with which an explosive can be ignited or detonated, i.e., the amount and intensity of shock , friction , or heat that is required. When the term sensitivity is used, care must be taken to clarify what kind of sensitivity is under discussion. The relative sensitivity of a given explosive to impact may vary greatly from its sensitivity to friction or heat. Some of
4331-410: The possibility of such side reactions, condensation of steam, and aqueous solubility of gases like carbon dioxide. Oxygen balance is an expression that is used to indicate the degree to which an explosive can be oxidized. If an explosive molecule contains just enough oxygen to convert all of its carbon to carbon dioxide, all of its hydrogen to water, and all of its metal to metal oxide with no excess,
SECTION 60
#17327907605404402-680: The predominant world standard cap type. The need for detonators such as blasting caps came from the development of safer secondary and tertiary explosives . Secondary and tertiary explosives are typically initiated by an explosives train starting with the detonator. For safety, detonators and the main explosive device are typically only joined just before use. A detonator is usually a multi stage device, with three parts: Explosives commonly used as primary in detonators include lead azide , lead styphnate , tetryl , and DDNP . Early blasting caps also used silver fulminate, but it has been replaced with cheaper and safer primary explosives. Silver azide
4473-426: The production of light , heat , sound , and pressure . An explosive charge is a measured quantity of explosive material, which may either be composed solely of one ingredient or be a mixture containing at least two substances. The potential energy stored in an explosive material may, for example, be: Explosive materials may be categorized by the speed at which they expand. Materials that detonate (the front of
4544-766: The required care. Ordinary detonators usually take the form of ignition-based explosives. While they are mainly used in commercial operations, ordinary detonators are still used in military operations. This form of detonator is most commonly initiated using a safety fuse , and used in non time-critical detonations e.g. conventional munitions disposal . Well known detonators are lead azide [Pb(N 3 ) 2 ], silver azide [AgN 3 ] and mercury fulminate [Hg(ONC) 2 ]. There are three categories of electrical detonators: instantaneous electrical detonators (IED), short period delay detonators (SPD) and long period delay detonators (LPD). SPDs are measured in milliseconds and LPDs are measured in seconds. In situations where nanosecond accuracy
4615-466: The rest of the cap and only assembled at the end of the process. Match type caps are now the most common type found worldwide. The exploding-bridgewire detonator was invented in the 1940s as part of the Manhattan Project to develop nuclear weapons. The design goal was to produce a detonator which functioned very rapidly and predictably). Both Match and Solid Pack type electric caps take
4686-460: The safest type to use around certain types of electromagnetic interference, and they have a built in time delay as the fuse burns down. Solid pack electric blasting caps use a thin bridgewire in direct contact (hence solid pack) with a primary explosive, which is heated by electric current and causes the detonation of the primary explosive. That primary explosive then detonates a larger charge of secondary explosive. Some solid pack fuses incorporate
4757-492: The sum of the masses of the two initial layers. There are applications where a shock wave, and electrostatics, can result in high velocity projectiles such as in an electrostatic particle accelerator . An explosion is a type of spontaneous chemical reaction that, once initiated, is driven by both a large exothermic change (great release of heat) and a large positive entropy change (great quantities of gases are released) in going from reactants to products, thereby constituting
4828-499: The test methods used to determine sensitivity relate to: Specific explosives (usually but not always highly sensitive on one or more of the three above axes) may be idiosyncratically sensitive to such factors as pressure drop, acceleration, the presence of sharp edges or rough surfaces, incompatible materials, or even — in rare cases — nuclear or electromagnetic radiation. These factors present special hazards that may rule out any practical utility. Sensitivity
4899-425: The two layers. As the length of time the shock wave spends at any point is small, we can see mixing of the two metals and their surface chemistries, through some fraction of the depth, and they tend to be mixed in some way. It is possible that some fraction of the surface material from either layer eventually gets ejected when the end of material is reached. Hence, the mass of the now "welded" bilayer, may be less than
4970-486: The wire actually vaporizes and explodes due to electric resistance heating. That electrically-driven explosion causes the low-density initiating explosive (usually PETN ) to detonate, which in turn detonates a higher density secondary explosive (typically RDX or HMX) in many EBW designs. In addition to firing very quickly when properly initiated, EBW detonators are much safer than blasting caps from stray static electricity and other electric current. Enough current will melt
5041-799: Was nitroglycerin , developed in 1847. Since nitroglycerin is a liquid and highly unstable, it was replaced by nitrocellulose , trinitrotoluene ( TNT ) in 1863, smokeless powder , dynamite in 1867 and gelignite (the latter two being sophisticated stabilized preparations of nitroglycerin rather than chemical alternatives, both invented by Alfred Nobel ). World War I saw the adoption of TNT in artillery shells. World War II saw extensive use of new explosives (see: List of explosives used during World War II ) . In turn, these have largely been replaced by more powerful explosives such as C-4 and PETN . However, C-4 and PETN react with metal and catch fire easily, yet unlike TNT, C-4 and PETN are waterproof and malleable. The largest commercial application of explosives
#539460