Misplaced Pages

#555444

46-445: Multi-modal container units, designed as reusable carriers to facilitate unit load handling of the goods contained, are also referred to as cargo, especially by shipping lines and logistics operators. When empty containers are shipped each unit is documented as a cargo and when goods are stored within, the contents are termed containerized cargo. Similarly, aircraft ULD boxes are also documented as cargo, with an associated packing list of

92-515: A cargo net also forms a ULD, but its load must be gauged for size in addition to being weighed to ensure aircraft door and hold clearances. The IATA publishes ULD regulations and notes there are 900,000 in service worth more than US$ 1 billion, averaging $ 1100 each. ULDs come in two forms: pallets and containers. ULD pallets are rugged sheets of aluminium with rims designed to lock onto cargo net lugs. ULD containers, also known as cans and pods, are closed containers often made of aluminium or

138-441: A combination of aluminium (frame) and Lexan (walls) but there are examples of containers made of GRP with an insulating foam core. Depending on the nature of the goods to be transported, ULDs may have built-in refrigeration units. Examples of common ULDs and their specifics are listed below. LD3s, LD6s, and LD11s will fit 787s , 777s , 747s , MD-11s , Il-86s , Il-96s , L-1011s and all Airbus wide-bodies. The 767 uses

184-436: A country. Therefore, many governments have enacted rules and regulations, administered by a customs agency, for the handling of cargo to minimize risks of terrorism and other crime. Governments are mainly concerned with cargo entering through a country's borders. The United States has been one of the leaders in securing cargo. They see cargo as a concern to national security . After the terrorist attacks of September 11th ,

230-469: A different shipper. Transshipment is normally fully legal and an everyday part of world trade. However, it can also be a method used to disguise intent, as is the case with illegal logging , smuggling , or grey-market goods. The transshipment of containers at a container port or terminal can be defined as the number (or proportion) of containers, possibly expressed in TEU , of the total container flow that

276-483: A freight broker, online marketplace or another intermediary, instead of contracting directly with a trucking company. Brokers can shop the marketplace and obtain lower rates than most smaller shippers can obtain directly. In the LTL marketplace, intermediaries typically receive 50% to 80% discounts from published rates, whereas a small shipper may only be offered a 5% to 30% discount by the carrier. Intermediaries are licensed by

322-446: A large number of containers that come from shipping ports. Trains are also used to transport water, cement, grain, steel, wood and coal. They are used because they can carry a large amount and generally have a direct route to the destination. Under the right circumstances, freight transport by rail is more economical and energy efficient than by road, mainly when carried in bulk or over long distances. The main disadvantage of rail freight

368-409: A large opening front for loading. Air freight shipments are very similar to LTL shipments in terms of size and packaging requirements. However, air freight or air cargo shipments typically need to move at much faster speeds than 800 km or 497 mi per hour. While shipments move faster than standard LTL, air shipments do not always actually move by air. Air shipments may be booked directly with

414-551: A single piece of equipment and are typically reloaded across multiple pieces of equipment during their transport, TL shipments usually travel as the only shipment on a trailer. In fact, TL shipments usually deliver on exactly the same trailer as they are picked up on. Freight is usually organized into various shipment categories before it is transported. An item's category is determined by: Shipments are typically categorized as household goods, express, parcel, and freight shipments: An LTL shipper often realizes savings by utilizing

460-446: A vessel's holds, but otherwise onto and off its deck, by cranes or derricks present on the dock or on the ship itself. If hoisted on deck instead of straight into the hold, liftable or rolling unit loads, like bags, barrels/vats, boxes, cartons and crates, then have to be man-handled and stowed competently by stevedores . Securing break bulk and general freight inside a vessel, includes the use of dunnage . When no hoisting equipment

506-609: A wide range in the pricing offered. If a shipper in the United States uses a broker, freight forwarder or another transportation intermediary, it is common for the shipper to receive a copy of the carrier's Federal Operating Authority. Freight brokers and intermediaries are also required by Federal Law to be licensed by the Federal Highway Administration . Experienced shippers avoid unlicensed brokers and forwarders because if brokers are working outside

SECTION 10

#1732764785556

552-455: Is available, break bulk would previously be man-carried on and off the ship, over a plank, or by passing via human chain . Since the 1960s, the volume of break bulk cargo has enormously declined worldwide in favour of mass adoption of containers . Bulk cargo , such as salt , oil , tallow , but also scrap metal , is usually defined as commodities that are neither on pallets nor in containers. Bulk cargoes are not handled as individual pieces,

598-557: Is counted twice in the port performance, since it is handled twice by the waterside container cranes (separate unloading from arriving ship A, waiting in the stack, and loading onto departing ship B). Transshipment at sea is done by transferring goods from one ship to another. In global fisheries transshipment is used to transfer catch to refrigerated cargo vessels that also supply fishing vessels with fuel, food, equipment and personnel allowing them to stay at sea for months or even years. This guarantees that fish quickly find their way to

644-600: Is cut in half, down the center line of the plane, (lower deck LD3 and upper deck AAX). Main deck ULDs and pallets are not only taller than lower deck ULDs, they are frequently two or four times longer. They are usually organized like an LD6, using the width of the plane and missing two profile corners, or two very long LD3s, stored in parallel to use the plane's width and each missing one profile corner, but often twice or four times as long from plane's nose to tail. Many air cargo companies use main deck ULDs that have both features called dual-profile, so that on smaller planes such as

690-408: Is food, as supermarkets require deliveries daily to replenish their shelves with goods. Retailers and manufacturers of all kinds rely upon delivery trucks , be they full size semi trucks or smaller delivery vans . These smaller road haulage companies constantly strive for the best routes and prices to ship out their products. Indeed, the level of commercial freight transported by smaller businesses

736-737: Is given in the International Guidelines on Safe Load Securing for Road Transport. Unit load device A unit load device ( ULD ) is a container used to load luggage, freight, and mail on wide-body aircraft and specific narrow-body aircraft . It allows preloading of cargo , provided the containerised load fits in the aircraft, enabling efficient planning of aircraft weight and balance and reduced labour and time in loading aircraft holds compared with 'bulk-loading' single items of cargo or luggage by hand. Each ULD has its own packing list or manifest so that its contents can be tracked. A loaded aircraft cargo pallet secured with

782-408: Is half the volume of a 125-inch (3,175 mm) × 88 inch pallet. The 20 foot pallet is 238 inches (6,045 mm) long and 96 inches (2,438 mm) wide. What the actual dimensions of contoured upper deck ULDs are is very hard to know, because most manufacturers only profile width, length and height data. There are several common types of contoured main deck ULDs, that are contoured (curved to fit in

828-414: Is handled at the port or terminal and, after temporary storage in the stack, transferred to another ship to reach their destinations. The exact definition of transshipment may differ between ports, mostly depending on the inclusion of inland water transport (barges operating on canals and rivers to the hinterland ). The definition of transshipment may: In both cases, a single, unique, transshipped container

874-415: Is its lack of flexibility. For this reason, rail has lost much of the freight business to road transport. Rail freight is often subject to transshipment costs, since it must be transferred from one mode of transportation to another. Practices such as containerization aim at minimizing these costs. When transporting point-to-point bulk loads such as cement or grain, with specialised bulk handling facilities at

920-516: Is often a good barometer of healthy economic development as these types of vehicles move and transport anything literally, including couriers transporting parcels and mail. You can see the different types and weights of vehicles that are used to move cargo around . Less than truckload (LTL) cargo is the first category of freight shipment, representing the majority of freight shipments and the majority of business-to-business (B2B) shipments. LTL shipments are also often referred to as motor freight and

966-612: Is possible when cargo needs to be quickly transferred to a connecting flight. Both LD2s and LD8s can be loaded in LD3/6/11 aircraft, but at the cost of using internal volume inefficiently (33 ft wasted per LD2). Only the LD3 of the LD3/6/11 family of ULDs can be loaded in a 767; it will occupy an entire row where two LD2s or one LD8 would otherwise have fit (90 ft wasted per LD3). Policies vary from airline to airline as to whether such transfers are allowed. The 787, intended to replace

SECTION 20

#1732764785556

1012-597: Is the shipment of goods or containers to an intermediate destination, then to another destination. One possible reason for transshipment is to change the means of transport during the journey (e.g., from ship transport to road transport ), known as transloading . Another reason is to combine small shipments into a large shipment (consolidation), or the opposite: dividing a large shipment into smaller shipments (deconsolidation). Transshipment usually takes place in transport hubs . Much international transshipment also takes place in designated customs areas , thus avoiding

1058-461: Is usually 48 ft (14.63 m). In tight and residential environments the 28 ft (8.53 m) trailer is used the most. The shipments are usually palletized, stretch [shrink]-wrapped and packaged for a mixed-freight environment. Unlike express or parcel, LTL shippers must provide their own packaging, as carriers do not provide any packaging supplies or assistance. However, circumstances may require crating or another substantial packaging. In

1104-488: The Boeing 747 and the more prominent An‑124 , which was purposely built for easy conversion into a cargo aircraft . Such large aircraft employ standardized quick-loading containers known as unit load devices (ULDs), comparable to ISO containers on cargo ships. ULDs can be stowed in the lower decks (front and rear) of several wide-body aircraft , and on the main deck of some narrow-bodies . Some dedicated cargo planes have

1150-408: The 767, was designed to use the LD3/6/11 family of ULDs to solve the wasted volume issue. Aircraft loads can consist of containers, pallets, or a mix of ULD types, depending on requirements. In some aircraft the two types must be mixed as some compartments take only specific ULDs. Container capacity of an aircraft is measured in positions . Each half-width container (LD1/LD2/LD3) in the aircraft it

1196-455: The Boeing 727, they are stored widthwise and have two corners contoured, and on the bigger Boeing 767, they can be rotated 90 degrees and shipped in parallel like LD3s, so that only one corner is contoured when being used like an LD3. This greatly simplifies transportation of cargo containers at slight cost of cargo volume. Transshipment Transshipment , trans-shipment or transhipment

1242-491: The DOT and have the requirements to provide proof of insurance. Truckload (TL) carriers usually charge a rate per kilometre or mile. The rate varies depending on the distance, geographic location of the delivery, items being shipped, equipment type required, and service times required. TL shipments usually receive a variety of surcharges very similar to those described for LTL shipments above. There are thousands more small carriers in

1288-781: The TL market than in the LTL market. Therefore, the use of transportation intermediaries or brokers is widespread. Another cost-saving method is facilitating pickups or deliveries at the carrier's terminals. Carriers or intermediaries can provide shippers with the address and phone number for the closest shipping terminal to the origin and/or destination. By doing this, shippers avoid any accessorial fees that might normally be charged for liftgate, residential pickup/ delivery , inside pickup/delivery, or notifications/appointments. Shipping experts optimize their service and costs by sampling rates from several carriers, brokers and online marketplaces. When obtaining rates from different providers, shippers may find

1334-554: The United States, shipments larger than about 7,000 kg (15,432 lb) are typically classified as truckload (TL) freight . This is because it is more efficient and economical for a large shipment to have exclusive use of one larger trailer rather than share space on a smaller LTL trailer. By the Federal Bridge Gross Weight Formula the total weight of a loaded truck (tractor and trailer, 5-axle rig) cannot exceed 80,000 lb (36,287 kg) in

1380-554: The United States. In ordinary circumstances, long-haul equipment will weigh about 15,000 kg (33,069 lb), leaving about 20,000 kg (44,092 lb) of freight capacity. Similarly a load is limited to the space available in the trailer, normally 48 ft (14.63 m) or 53 ft (16.15 m) long, 2.6 m ( 102 + 3 ⁄ 8  in) wide, 9 ft 0 in (2.74 m) high and 13 ft 6 in or 4.11 m high overall. While express, parcel and LTL shipments are always intermingled with other shipments on

1426-551: The carriers involved are referred to as motor carriers . LTL shipments range from 50 to 7,000 kg (110 to 15,430 lb), being less than 2.5 to 8.5 m (8 ft 2.4 in to 27 ft 10.6 in) the majority of times. The average single piece of LTL freight is 600 kg (1,323 lb) and the size of a standard pallet. Long freight and/or large freight are subject to extreme length and cubic capacity surcharges. Trailers used in LTL can range from 28 to 53 ft (8.53 to 16.15 m). The standard for city deliveries

Cargo - Misplaced Pages Continue

1472-566: The carriers, through brokers or with online marketplace services. In the US, there are certain restrictions on cargo moving via air freight on passenger aircraft, most notably the transport of rechargeable lithium-ion battery shipments. Shippers in the US must be approved and be "known" in the Known Shipper Management System before their shipments can be tendered on passenger aircraft. Trains are capable of transporting

1518-531: The export of bulk minerals including bauxite , iron ore and potash from mines in Queensland , Western Australia and the Northern Territory . At a break-of-gauge , cargo is transloaded from boxcars or covered goods wagons on one track to wagons on another track of a different rail gauge , or else containers are transloaded from flatcars on one track to flatcars on another track of

1564-435: The items contained within. Seaport terminals handle a wide range of maritime cargoes . Break bulk / general cargo are goods that are handled and stowed piecemeal to some degree, as opposed to cargo in bulk or modern shipping containers . Typically bundled in batches for hoisting, either with cargo nets , slings, crates , or stacked on trays, pallets or skids; at best (and today mostly) lifted directly into and out of

1610-521: The law by not having a Federal Operating License, the shipper has no protection in case of a problem. Also, shippers typically ask for a copy of the broker's insurance certificate and any specific insurance that applies to the shipment. Overall, shipping costs have fallen over the past decades. A further drop in shipping costs in the future might be realized through the application of improved 3D printing technologies.  Governments are very concerned with cargo shipment, as it may bring security risks to

1656-413: The market without a decrease in quality. Since transshipment at sea encounters often happen on the high seas, in regions with poor regulation and oversight, they are also used to disguise criminal activities such as illegal, unreported and unregulated fishing , forced labor , human trafficking and drug smuggling . Several states and regional fishery management organizations have therefore prohibited

1702-402: The need for customs checks or duties, otherwise a major hindrance for efficient transport. An item handled (from the shipper's point of view) as a single movement is not generally considered transshipped, even if it changes from one mode of transport to another at several points. Previously, it was often not distinguished from transloading , since each leg of such a trip was typically handled by

1748-503: The plane's body) to provide as much cargo volume as possible. Initially ULD contouring was simply a triangle removed from one or two corners of the profile of the ULD, such as the common LD3 and LD6. Main deck ULDs use curves for the contoured shape to truly maximize cargo volume. Upper deck ULDs are just like lower deck ULDs that are either the full width of the plane with two corners of the profile removed (lower deck LD6 lower), or that container

1794-429: The practice for certain vessel types or issued a complete ban within their zone of jurisdiction. Transshipment at sea also occurs in the export of bulk products. Choosing to transship reduces capital costs for port developers and can overcome problems arising from limited access to deep water. Loading barges typically specify 4 to 7 meters of draft. Since at least 2011, transshipment has been used in northern Australia in

1840-498: The rail sidings, the rail mode of transport remains the most convenient and preferred option. Many governments are encouraging shippers to increase their use of rail rather than transport because of trains' lower environmental disbenefits. Many firms, like Parcelforce , FedEx and R+L Carriers transport all types of cargo by road. Delivering everything from letters to houses to cargo containers , these firms offer fast, sometimes same-day, delivery . A good example of road cargo

1886-623: The same type, and ending with a two character (alpha-numerical) suffix identifying the ULD's owner (if an airline, often the same as IATA designator codes). For example, AKN 12345 DL means that the ULD is a forkliftable LD3 with the unique number 12345 and its owner is Delta Air Lines . On the main deck of cargo planes are 79 to 108 inches (2,007 to 2,743 mm) tall ULDs with footprints similar to those of 88 inches (2,235 mm) or 96 inches (2,438 mm) wide pallets and 62 inches (1,575 mm) or 125 inches (3,175 mm) long. A 62-inch (1,575 mm) wide × 88-inch (2,235 mm) tall ULD

Cargo - Misplaced Pages Continue

1932-1093: The security of this magnitude of cargo has become highlighted on the over 6 million cargo containers that enter the United States ports each year. The latest US Government response to this threat is the CSI: Container Security Initiative . CSI is a program intended to help increase security for containerized cargo shipped to the United States from around the world. Europe is also focusing on this issue, with several EU-funded projects underway. Many ways and materials are available to stabilize and secure cargo in various modes of transport. Conventional load securing methods and materials such as steel strapping and plastic/wood blocking and bracing have been used for decades and are still widely used. Present load-securing methods offer several other options, including polyester strapping and lashing, synthetic webbings and dunnage bags, also known as airbags or inflatable bags. Practical advice on stabilization

1978-694: The smaller LD2s and LD8s because of its narrower fuselage. The less common LD1 is designed specifically for the 747, but LD3s are more commonly used in its place because of ubiquity (they have the same floor dimensions such that one LD3 takes the place of one LD1). LD3s with reduced height (1.14 metres (45 in) instead of 1.63 metres (64 in)) can also be loaded on the Airbus A320 family . LD7 pallets will fit 787s, 777s, 747s, late model 767s (with larger doors), and Airbus wide-bodies. Interchangeability of certain ULDs between LD3/6/11 aircraft and LD2/8 aircraft

2024-462: The two positions of the following row) or four LD2 positions. PMCs can only be loaded in cargo compartments with large doors designed to accept them (small door compartments are container-only). All ULDs are identified by their ULD number. A three-letter prefix identifies its type and key characteristics, followed by a 4 or 5 digit serial number (4 if prior to October 1, 1993; either 4 or 5 if after October 1, 1993) to uniquely identify it from others of

2070-547: The way heavy-lift and project cargo are. Alumina , grain , gypsum , logs, and wood chips, for instance, are bulk cargoes. Bulk cargo is classified as liquid or dry . Air cargo refers to any goods shipped by air, whereas air freight refers specifically to goods transported in the cargo hold of a dedicated cargo plane. Aircraft were first used to carry mail as cargo in 1911. Eventually manufacturers started designing aircraft for other types of freight as well. There are many commercial aircraft suitable for carrying cargo such as

2116-483: Was designed for occupies one position. Typically, each row in a cargo compartment consists of two positions. Therefore, a full-width container (LD6/LD8/LD11) will take two positions. An LD6 or an LD11 can occupy the space of two LD3s. An LD8 takes the space of two LD2s. Aircraft pallet capacity is measured by how many PMC-type LD7s 96 by 125 in (240 by 320 cm) can be stored. These pallets occupy approximately three LD3 positions (two positions of one row and half of

#555444