CrossDOS is a file system handler for accessing FAT formatted media on Amiga computers. It was bundled with AmigaOS 2.1 and later. Its function was to allow working with disks formatted for PCs and Atari STs (and others). In the 1990s it became a commonly used method of file exchange between Amiga systems and other platforms.
76-473: CrossDOS supported both double density (720 KB) and high density (1.44 MB) floppy disks on compatible disk drives. As with AmigaDOS disk handling, it allowed automatic disk-change detection for FAT formatted floppy disks. The file system was also used with hard disks and other media for which CrossDOS provided hard disk configuration software. However, the versions of CrossDOS bundled with AmigaOS did not support long filenames, an extension to FAT that
152-439: A floppy , a diskette , or a disk ) is a type of disk storage composed of a thin and flexible disk of a magnetic storage medium in a square or nearly square plastic enclosure lined with a fabric that removes dust particles from the spinning disk. The three most popular (and commercially available) floppy disks are the 8-inch, 5¼-inch, and 3½-inch floppy disks. Floppy disks store digital data which can be read and written when
228-443: A button that, when pressed, ejects the disk with varying degrees of force, the discrepancy due to the ejection force provided by the spring of the shutter. In IBM PC compatibles , Commodores, Apple II/IIIs, and other non-Apple-Macintosh machines with standard floppy disk drives, a disk may be ejected manually at any time. The drive has a disk-change switch that detects when a disk is ejected or inserted. Failure of this mechanical switch
304-650: A customized operating system is used that has no drivers for USB devices. Hardware floppy disk emulators can be made to interface floppy-disk controllers to a USB port that can be used for flash drives. In May 2016, the United States Government Accountability Office released a report that covered the need to upgrade or replace legacy computer systems within federal agencies. According to this document, old IBM Series/1 minicomputers running on 8-inch floppy disks are still used to coordinate "the operational functions of
380-428: A disk can be accessed, the drive needs to synchronize its head position with the disk tracks. In some drives, this is accomplished with a Track Zero Sensor, while for others it involves the drive head striking an immobile reference surface. In either case, the head is moved so that it is approaching track zero position of the disk. When a drive with the sensor has reached track zero, the head stops moving immediately and
456-474: A disk, some 3½-inch drives (notably the Macintosh External 400K and 800K drives ) instead use Constant Linear Velocity (CLV), which uses a variable speed drive motor that spins more slowly as the head moves away from the center of the disk, maintaining the same speed of the head(s) relative to the surface(s) of the disk. This allows more sectors to be written to the longer middle and outer tracks as
532-452: A format of (usually 5 + 1 ⁄ 4 -inch) floppy disks which could typically hold 35-40 tracks of nine 512- byte (or 18 256-byte) sectors each. Only one side of the disc was used, although some users did discover that punching additional holes into the disc jacket would allow the creation of a "flippy" disc which could be manually turned over to store additional data on the reverse side. Single-sided disks began to become obsolete after
608-506: A gap must be left between sectors to allow a rewritten sector to be larger without over-writing the following sector. Commodore's Amiga used an unusual format which got closer to the disk's raw (unformatted) capacity by eliminating the gaps between sectors and simplifying the identification data. This meant that individual sectors could not be rewritten; the Amiga would simply rewrite the entire track. Formatted capacity numbers are based on
684-413: A hard-sectored disk, there are many holes, one for each sector row, plus an additional hole in a half-sector position, that is used to indicate sector zero. The Apple II computer system is notable in that it did not have an index hole sensor and ignored the presence of hard or soft sectoring. Instead, it used special repeating data synchronization patterns written to the disk between each sector, to assist
760-448: A hole). If the motor is spinning any slower than the highest acceptable speed, which is usually the case, the data will fit in fewer than 360 degrees, resulting in a gap at the end of the track. Additionally, if a sector were to be rewritten on a drive running faster than the drive was running when the track was formatted, the new data would be larger (occupy more degrees of rotation) than the original sector. Therefore, during formatting
836-420: A loaded disk can be removed manually by inserting a straightened paper clip into a small hole at the drive's front panel, just as one would do with a CD-ROM drive in a similar situation. The X68000 has soft-eject 5¼-inch drives. Some late-generation IBM PS/2 machines had soft-eject 3½-inch disk drives as well for which some issues of DOS (i.e. PC DOS 5.02 and higher) offered an EJECT command. Before
SECTION 10
#1732783621191912-557: A recovery. The music and theatre industries still use equipment requiring standard floppy disks (e.g. synthesizers, samplers, drum machines, sequencers, and lighting consoles ). Industrial automation equipment such as programmable machinery and industrial robots may not have a USB interface; data and programs are then loaded from disks, damageable in industrial environments. This equipment may not be replaced due to cost or requirement for continuous availability; existing software emulation and virtualization do not solve this problem because
988-582: A secondary floppy disk drive only (this tool was not a complete file system but a user program to read files from a FAT formatted disk). Development of CrossDOS continued after being bundled with the OS. CrossDOS 7 was the last version released and included support for long filenames and other features not available in the bundled version. This computer-storage -related article is a stub . You can help Misplaced Pages by expanding it . Floppy disk A floppy disk or floppy diskette (casually referred to as
1064-468: A selectable option and purchasable as an aftermarket OEM add-on. By January 2007, only 2% of computers sold in stores contained built-in floppy disk drives. Floppy disks are used for emergency boots in aging systems lacking support for other bootable media and for BIOS updates, since most BIOS and firmware programs can still be executed from bootable floppy disks . If BIOS updates fail or become corrupt, floppy drives can sometimes be used to perform
1140-505: A single hole in the rotating floppy disk medium line up. This mechanism is used to detect the angular start of each track, and whether or not the disk is rotating at the correct speed. Early 8‑inch and 5¼‑inch disks also had holes for each sector in the enclosed magnetic medium, in addition to the index hole, with the same radial distance from the center, for alignment with the same envelope hole. These were termed hard sectored disks. Later soft- sectored disks have only one index hole in
1216-447: A small circle of floppy magnetic material encased in hard plastic. Earlier types of floppy disks did not have this plastic case, which protects the magnetic material from abuse and damage. A sliding metal cover protects the delicate magnetic surface when the diskette is not in use and automatically opens when the diskette is inserted into the computer. The diskette has a square shape: there are apparently eight possible ways to insert it into
1292-411: A small oblong opening in both sides to allow the drive's heads to read and write data and a large hole in the center to allow the magnetic medium to spin by rotating it from its middle hole. Inside the cover are two layers of fabric with the magnetic medium sandwiched in the middle. The fabric is designed to reduce friction between the medium and the outer cover, and catch particles of debris abraded off
1368-475: Is a common source of disk corruption if a disk is changed and the drive (and hence the operating system) fails to notice. One of the chief usability problems of the floppy disk is its vulnerability; even inside a closed plastic housing, the disk medium is highly sensitive to dust, condensation and temperature extremes. As with all magnetic storage , it is vulnerable to magnetic fields. Blank disks have been distributed with an extensive set of warnings, cautioning
1444-456: Is correctly aligned. For a drive without the sensor, the mechanism attempts to move the head the maximum possible number of positions needed to reach track zero, knowing that once this motion is complete, the head will be positioned over track zero. Some drive mechanisms such as the Apple II 5¼-inch drive without a track zero sensor, produce characteristic mechanical noises when trying to move
1520-533: Is file-system and configuration specific and always lower than the formatted capacity, since the file system occupies a number of the available sectors for control structures as well. Most floppy disks used by PCs use the FAT12 file system format, which imposes certain practical defaults on the logical geometry in order to be recognizable by all operating systems. Sometimes disks may use a more exotic file system. SSDD originally referred to Single Sided, Double Density,
1596-428: Is still used by software on user-interface elements related to saving files even though physical floppy disks are largely obsolete. Examples of such software include LibreOffice , Microsoft Paint , and WordPad . The 8-inch and 5¼-inch floppy disks contain a magnetically coated round plastic medium with a large circular hole in the center for a drive's spindle. The medium is contained in a square plastic cover that has
SECTION 20
#17327836211911672-409: Is used for magnetic recording). An additional hole is punched near one of the sector holes to identify the start of the track. A sensor in the drive detects the holes in the magnetic media as they align with a hole in the disk jacket. Data is generally written at a fixed number of bits per second, with only a very small percentage of variation due to component tolerances, so given the nominal speed that
1748-405: Is used for sector identification and for gaps (empty spaces) between sectors and at the end of the track. In hard-sectored 8-inch and 5 + 1 ⁄ 4 -inch formats, each track is divided into a particular number of sectors determined when the disk is manufactured. Holes are punched in the magnetic media to indicate where each sector should start (in an area closer to the center of the disk than
1824-551: The Type 1 Diskette in 1973, the industry continued to use the terms "floppy disk" or "floppy". In 1976, Shugart Associates introduced the 5¼-inch floppy disk drive. By 1978, there were more than ten manufacturers producing such drives. There were competing floppy disk formats , with hard- and soft-sector versions and encoding schemes such as differential Manchester encoding (DM), modified frequency modulation (MFM), M FM and group coded recording (GCR). The 5¼-inch format displaced
1900-398: The 1990s were non-networked, and floppy disks were the primary means to transfer data between computers, a method known informally as sneakernet . Unlike hard disks, floppy disks were handled and seen; even a novice user could identify a floppy disk. Because of these factors, a picture of a 3½-inch floppy disk became an interface metaphor for saving data. As of 2024 , the floppy disk symbol
1976-469: The 21st century, as a form of skeuomorphic design . While floppy disk drives still have some limited uses, especially with legacy industrial computer equipment , they have been superseded by data storage methods with much greater data storage capacity and data transfer speed , such as USB flash drives , memory cards , optical discs , and storage available through local computer networks and cloud storage . The first commercial floppy disks, developed in
2052-527: The 720 KB double density 3½-inch microfloppy disk on its Convertible laptop computer in 1986 and the 1.44 MB (1,474,560 bytes) high-density version with the IBM Personal System/2 (PS/2) line in 1987. These disk drives could be added to older PC models. In 1988, Y-E Data introduced a drive for 2.88 MB Double-Sided Extended-Density (DSED) diskettes which was used by IBM in its top-of-the-line PS/2 and some RS/6000 models and in
2128-548: The 8-inch one for most uses, and the hard-sectored disk format disappeared. The most common capacity of the 5¼-inch format in DOS-based PCs was 360 KB (368,640 bytes) for the Double-Sided Double-Density (DSDD) format using MFM encoding. In 1984, IBM introduced with its PC/AT the 1.2 MB (1,228,800 bytes) dual-sided 5¼-inch floppy disk, but it never became very popular. IBM started using
2204-473: The Sony design, introduced in 1983 by many manufacturers, was then rapidly adopted. By 1988, the 3½-inch was outselling the 5¼-inch. Generally, the term floppy disk persisted, even though later style floppy disks have a rigid case around an internal floppy disk. By the end of the 1980s, 5¼-inch disks had been superseded by 3½-inch disks. During this time, PCs frequently came equipped with drives of both sizes. By
2280-647: The United States' nuclear forces". The government planned to update some of the technology by the end of the 2017 fiscal year. Use in Japan's government ended in 2024. Windows 10 and Windows 11 no longer come with drivers for floppy disk drives (both internal and external). However, they will still support them with a separate device driver provided by Microsoft. The British Airways Boeing 747-400 fleet, up to its retirement in 2020, used 3½-inch floppy disks to load avionics software. Sony, who had been in
2356-409: The computer in finding and synchronizing with the data in each track. The later 3½-inch drives of the mid-1980s did not use sector index holes, but instead also used synchronization patterns. Most 3½-inch drives used a constant speed drive motor and contain the same number of sectors across all tracks. This is sometimes referred to as Constant Angular Velocity (CAV). In order to fit more data onto
CrossDOS - Misplaced Pages Continue
2432-406: The corresponding sensor; this was mainly a hardware cost-saving measure. The core of the 3½-inch disk is the same as the other two disks, but the front has only a label and a small opening for reading and writing data, protected by the shutter—a spring-loaded metal or plastic cover, pushed to the side on entry into the drive. Rather than having a hole in the center, it has a metal hub which mates to
2508-399: The current is reversed the magnetization aligns in the opposite direction, encoding one bit of data. To read data, the magnetization of the particles in the media induce a tiny voltage in the head coil as they pass under it. This small signal is amplified and sent to the floppy disk controller , which converts the streams of pulses from the media into data, checks it for errors, and sends it to
2584-835: The disk is inserted into a floppy disk drive ( FDD ) connected to or inside a computer or other device. The first floppy disks, invented and made by IBM in 1971, had a disk diameter of 8 inches (203.2 mm). Subsequently, the 5¼-inch (133.35 mm) and then the 3½-inch (88.9 mm) became a ubiquitous form of data storage and transfer into the first years of the 21st century. 3½-inch floppy disks can still be used with an external USB floppy disk drive. USB drives for 5¼-inch, 8-inch, and other-size floppy disks are rare to non-existent. Some individuals and organizations continue to use older equipment to read or transfer data from floppy disks. Floppy disks were so common in late 20th-century culture that many electronic and software programs continue to use save icons that look like floppy disks well into
2660-399: The disk media, an action originally accomplished by a disk-load solenoid. Later drives held the heads out of contact until a front-panel lever was rotated (5¼-inch) or disk insertion was complete (3½-inch). To write data, current is sent through a coil in the head as the media rotates. The head's magnetic field aligns the magnetization of the particles directly below the head on the media. When
2736-449: The disk rotates it is possible to calculate the number of degrees a given number of bytes will occupy when written. In practice the motor speed varies, especially from one drive to another, resulting in those bytes occupying more degrees of the track at high motor speeds or fewer degrees at low motor speeds. When a soft-sectored disk is low-level "formatted", each track is written with a number of bytes calculated to fit within 360 degrees at
2812-442: The disk shell are not quite square: its width is slightly less than its depth, so that it is impossible to insert the disk into a drive slot sideways (i.e. rotated 90 degrees from the correct shutter-first orientation). A diagonal notch at top right ensures that the disk is inserted into the drive in the correct orientation—not upside down or label-end first—and an arrow at top left indicates direction of insertion. The drive usually has
2888-425: The disk sleeve to make them usable as flippy disks . A combination floppy disk and optical disc , known as a Floptical disk exists. The size of a 3 + 1 ⁄ 2 -inch (90 mm) disk, they are capable of holding close to 20.8 MB, but need a special drive. The formatted disk capacity is always less than the "raw" unformatted capacity specified by the disk's manufacturer, because some portion of each track
2964-466: The disk to keep them from accumulating on the heads. The cover is usually a one-part sheet, double-folded with flaps glued or spot-welded together. A small notch on the side of the disk identifies whether it is writable, as detected by a mechanical switch or photoelectric sensor . In the 8-inch disk, the notch being covered or not present enables writing, while in the 5¼-inch disk, the notch being present and uncovered enables writing. Tape may be used over
3040-435: The early 2000s, most floppy disk types and formats became obsolete, leaving the 3 + 1 ⁄ 2 -inch disk, using an IBM PC compatible format of 1440 KB, as the only remaining popular format. Different floppy disk types had different recording characteristics, with varying magnetic coercivity (measured in oersteds , or in modern SI units in amperes per meter), ferrite grain size, and tracks per inch (TPI). TPI
3116-406: The eight ways one might try to insert the diskette, only one is correct, and only that one will fit. An excellent design. A spindle motor in the drive rotates the magnetic medium at a certain speed, while a stepper motor-operated mechanism moves the magnetic read/write heads radially along the surface of the disk. Both read and write operations require the media to be rotating and the head to contact
CrossDOS - Misplaced Pages Continue
3192-692: The existing 3½-inch designs was the SuperDisk in the late 1990s, using very narrow data tracks and a high precision head guidance mechanism with a capacity of 120 MB and backward-compatibility with standard 3½-inch floppies; a format war briefly occurred between SuperDisk and other high-density floppy-disk products, although ultimately recordable CDs/DVDs, solid-state flash storage, and eventually cloud-based online storage would render all these removable disk formats obsolete. External USB -based floppy disk drives are still available, and many modern systems provide firmware support for booting from such drives. In
3268-555: The flexibility of floppy disks combined with greater capacity, but remained niche due to costs. High-capacity backward compatible floppy technologies became popular for a while and were sold as an option or even included in standard PCs, but in the long run, their use was limited to professionals and enthusiasts. Flash-based USB thumb drives finally were a practical and popular replacement, that supported traditional file systems and all common usage scenarios of floppy disks. As opposed to other solutions, no new drive type or special software
3344-457: The floppy disk business since 1983, ended domestic sales of all six 3½-inch floppy disk models as of March 2011. This has been viewed by some as the end of the floppy disk. While production of new floppy disk media has ceased, sales and uses of this media from inventories is expected to continue until at least 2026. For more than two decades, the floppy disk was the primary external writable storage device used. Most computing environments before
3420-512: The general population, floppy disks were often used to store a computer's operating system (OS). Most home computers from that time have an elementary OS and BASIC stored in read-only memory (ROM), with the option of loading a more advanced OS from a floppy disk. By the early 1990s, the increasing software size meant large packages like Windows or Adobe Photoshop required a dozen disks or more. In 1996, there were an estimated five billion standard floppy disks in use. An attempt to enhance
3496-431: The greater capacity, compatibility with existing CD-ROM drives, and—with the advent of re-writeable CDs and packet writing—a similar reusability as floppy disks. However, CD-R/RWs remained mostly an archival medium, not a medium for exchanging data or editing files on the medium itself, because there was no common standard for packet writing which allowed for small updates. Other formats, such as magneto-optical discs , had
3572-425: The hardware platform. Variables included the size of media (nominal 8-inch, 5 + 1 ⁄ 4 -inch, 3 + 1 ⁄ 2 -inch and others), encoding of data on the media (FM, MFM, M²FM, GCR), the number of disk tracks, one or two sides, the number of sectors in each track, and hard- or soft-sectoring. Even media that was physically interchangeable between two systems might not have been usable owing to particulars of
3648-407: The heads past the reference surface. This physical striking is responsible for the 5¼-inch drive clicking during the boot of an Apple II, and the loud rattles of its DOS and ProDOS when disk errors occurred and track zero synchronization was attempted. All 8-inch and some 5¼-inch drives used a mechanical method to locate sectors, known as either hard sectors or soft sectors , and is the purpose of
3724-404: The highest expected motor speed. Special bit patterns are written right before the location where a sector should start, and serve as identifiers, similar to the punched holes used by hard-sectored disks. Thus, the full constellation of punched holes is not needed, and only a single hole is retained, to indicate the start of the track ( 3 + 1 ⁄ 2 -inch disks use an alignment pin rather than
3800-450: The host computer system. A blank unformatted diskette has a coating of magnetic oxide with no magnetic order to the particles. During formatting, the magnetizations of the particles are aligned forming tracks, each broken up into sectors , enabling the controller to properly read and write data. The tracks are concentric rings around the center, with spaces between tracks where no data is written; gaps with padding bytes are provided between
3876-465: The introduction of IBM PC DOS 1.1 in 1982, which added support for double-side diskette drives with capacity of 320 KB to the IBM 5150 PC . In 1983 PC DOS 2.0 pushed the formatting capacity to 180 KB single-sided or 360 KB double-sided by utilizing 9 instead of only 8 sectors per track. Throughout the 1970s and 1980s, many different disk formats were used, depending on
SECTION 50
#17327836211913952-499: The late 1960s, were 8 inches (203.2 mm) in diameter; they became commercially available in 1971 as a component of IBM products and both drives and disks were then sold separately starting in 1972 by Memorex and others. These disks and associated drives were produced and improved upon by IBM and other companies such as Memorex, Shugart Associates , and Burroughs Corporation . The term "floppy disk" appeared in print as early as 1970, and although IBM announced its first media as
4028-424: The machine, only one of which is correct. What happens if I do it wrong? I try inserting the disk sideways. Ah, the designer thought of that. A little study shows that the case really isn't square: it's rectangular, so you can't insert a longer side. I try backward. The diskette goes in only part of the way. Small protrusions, indentations, and cutouts prevent the diskette from being inserted backward or upside down: of
4104-476: The media, with MFM assumed to be the logical format used. GCR was also used on some platforms, but typically in a "double" density form. 8- and 5 + 1 ⁄ 4 -inch floppy disks were available with both soft sectoring and hard sectoring . Because of the similarity in magnetic characteristics between some disk types, it was possible to use an incorrectly certified disk in a soft sectored drive. Quad density 5 + 1 ⁄ 4 -inch disks were rare, so it
4180-399: The media. In some 5¼-inch drives, insertion of the disk compresses and locks an ejection spring which partially ejects the disk upon opening the catch or lever. This enables a smaller concave area for the thumb and fingers to grasp the disk during removal. Newer 5¼-inch drives and all 3½-inch drives automatically engage the spindle and heads when a disk is inserted, doing the opposite with
4256-400: The medium, and sector position is determined by the disk controller or low-level software from patterns marking the start of a sector. Generally, the same drives are used to read and write both types of disks, with only the disks and controllers differing. Some operating systems using soft sectors, such as Apple DOS , do not use the index hole, and the drives designed for such systems often lack
4332-493: The mid-1990s, 5¼-inch drives had virtually disappeared, as the 3½-inch disk became the predominant floppy disk. The advantages of the 3½-inch disk were its higher capacity, its smaller physical size, and its rigid case which provided better protection from dirt and other environmental risks. Floppy disks became commonplace during the 1980s and 1990s in their use with personal computers to distribute software, transfer data, and create backups . Before hard disks became affordable to
4408-485: The mid-1990s, mechanically incompatible higher-density floppy disks were introduced, like the Iomega Zip disk . Adoption was limited by the competition between proprietary formats and the need to buy expensive drives for computers where the disks would be used. In some cases, failure in market penetration was exacerbated by the release of higher-capacity versions of the drive and media being not backward-compatible with
4484-526: The notch to change the mode of the disk. Punch devices were sold to convert read-only 5¼" disks to writable ones, and also to enable writing on the unused side of single-sided disks for computers with single-sided drives. The latter worked because single- and double-sided disks typically contained essentially identical actual magnetic media, for manufacturing efficiency. Disks whose obverse and reverse sides were thus used separately in single-sided drives were known as flippy disks . Disk notching 5¼" floppies for PCs
4560-485: The old format, including a rigid case with a sliding metal (or later, sometimes plastic) shutter over the head slot, which helped protect the delicate magnetic medium from dust and damage, and a sliding write protection tab, which was far more convenient than the adhesive tabs used with earlier disks. The large market share of the well-established 5¼-inch format made it difficult for these diverse mutually-incompatible new formats to gain significant market share. A variant on
4636-492: The original drives, dividing the users between new and old adopters. Consumers were wary of making costly investments into unproven and rapidly changing technologies, so none of the technologies became the established standard. Apple introduced the iMac G3 in 1998 with a CD-ROM drive but no floppy drive; this made USB-connected floppy drives popular accessories, as the iMac came without any writable removable media device. Recordable CDs were touted as an alternative, because of
SECTION 60
#17327836211914712-409: The press of the eject button. On Apple Macintosh computers with built-in 3½-inch disk drives, the ejection button is replaced by software controlling an ejection motor which only does so when the operating system no longer needs to access the drive. The user could drag the image of the floppy drive to the trash can on the desktop to eject the disk. In the case of a power failure or drive malfunction,
4788-403: The read operation; other errors are permanent and the disk controller will signal a failure to the operating system if multiple attempts to read the data still fail. After a disk is inserted, a catch or lever at the front of the drive is manually lowered to prevent the disk from accidentally emerging, engage the spindle clamping hub, and in two-sided drives, engage the second read/write head with
4864-580: The resulting number of logical sectors and the byte payload they can carry, that is, they depend on the physical parameters and modulation, but are independent of a particular file system. Sometimes floppies are superformatted to use more tracks or sectors per track to accommodate slightly more data. Some floppy-based Linux distributions utilize such techniques. For comparison purposes, formatted capacities given in this section assume standard disk geometries as they are supported by common operating systems in their default configuration. The maximum usable capacity
4940-651: The second-generation NeXTcube and NeXTstation ; however, this format had limited market success due to lack of standards and movement to 1.44 MB drives. Throughout the early 1980s, limits of the 5¼-inch format became clear. Originally designed to be more practical than the 8-inch format, it was becoming considered too large; as the quality of recording media grew, data could be stored in a smaller area. Several solutions were developed, with drives at 2-, 2½-, 3-, 3¼-, 3½- and 4-inches (and Sony 's 90 mm × 94 mm (3.54 in × 3.70 in) disk) offered by various companies. They all had several advantages over
5016-502: The sectors and at the end of the track to allow for slight speed variations in the disk drive, and to permit better interoperability with disk drives connected to other similar systems. Each sector of data has a header that identifies the sector location on the disk. A cyclic redundancy check (CRC) is written into the sector headers and at the end of the user data so that the disk controller can detect potential errors. Some errors are soft and can be resolved by automatically re-trying
5092-413: The small hole in the jacket, off to the side of the spindle hole. A light beam sensor detects when a punched hole in the disk is visible through the hole in the jacket. For a soft-sectored disk, there is only a single hole, which is used to locate the first sector of each track. Clock timing is then used to find the other sectors behind it, which requires precise speed regulation of the drive motor. For
5168-408: The spindle of the drive. Typical 3½-inch disk magnetic coating materials are: Two holes at the bottom left and right indicate whether the disk is write-protected and whether it is high-density; these holes are spaced as far apart as the holes in punched A4 paper, allowing write-protected high-density floppy disks to be clipped into international standard ( ISO 838 ) ring binders . The dimensions of
5244-514: The track length increases. While the original IBM 8-inch disk was actually so defined, the other sizes are defined in the metric system, their usual names being but rough approximations. Floppy disk format Floppy disk format and density refer to the logical and physical layout of data stored on a floppy disk . Since their introduction, there have been many popular and rare floppy disk types, densities, and formats used in computing, leading to much confusion over their differences. In
5320-442: The user not to expose it to dangerous conditions. Rough treatment or removing the disk from the drive while the magnetic media is still spinning is likely to cause damage to the disk, drive head, or stored data. On the other hand, the 3½‑inch floppy disk has been lauded for its mechanical usability by human–computer interaction expert Donald Norman : A simple example of a good design is the 3½-inch magnetic diskette for computers,
5396-409: Was generally only required where users wanted to overwrite original 5¼" disks of store-bought software, which somewhat commonly shipped with no notch present. Another LED/photo-transistor pair located near the center of the disk detects the index hole once per rotation in the magnetic disk. Detection occurs whenever the drive's sensor, the holes in the correctly inserted floppy's plastic envelope and
5472-513: Was introduced with Microsoft 's Windows 95 . CrossDOS was originally developed as a stand-alone commercial product by Consultron, which was available for AmigaOS 1.2 and 1.3. In 1992 Commodore included a version of CrossDOS with AmigaOS 2.1 (and with later versions), so that users could work with PC formatted disks. In fact, the bundled version will also work with version 2.0 of AmigaOS. The bundled CrossDOS replaced an obscure tool in earlier versions of AmigaOS that could access FAT formatted disks on
5548-468: Was little financial incentive to omit the device from a system. Subsequently, enabled by the widespread support for USB flash drives and BIOS boot, manufacturers and retailers progressively reduced the availability of floppy disk drives as standard equipment. In February 2003, Dell , one of the leading personal computer vendors, announced that floppy drives would no longer be pre-installed on Dell Dimension home computers, although they were still available as
5624-453: Was not a part of the physical manufacturing process; it was a certification of how closely tracks of data could be spaced on the medium safely. The term density has a double meaning for floppy disks. Originally, single density and double density indicated a difference in logical encoding on the same type of physical media: FM for single, and MFM for double. Subsequent use of the term "density" referred to physical characteristics of
5700-614: Was not uncommon to use higher quality double density disks, which were usually capable of sustaining the 96 TPI formatting of quad density, in drives such as the Commodore 8050 . Disks were available in both single and double sided forms, with double sided formats providing twice the storage capacity. Like TPI, "double sided" was mostly a certification indicator, as the magnetic media was usually recordable on both sides. Many (but not all) certified "double sided" 8- and 5 + 1 ⁄ 4 -inch floppies had an index hole on both sides of
5776-443: Was required that impeded adoption, since all that was necessary was an already common USB port . By 2002, most manufacturers still provided floppy disk drives as standard equipment to meet user demand for file-transfer and an emergency boot device, as well as for the general secure feeling of having the familiar device. By this time, the retail cost of a floppy drive had fallen to around $ 20 (equivalent to $ 34 in 2023), so there
#190809