Misplaced Pages

#911088

69-655: The AN/AAQ-37 Distributed Aperture System (DAS) is the first of a new generation of sensor systems being fielded on the Lockheed Martin F-35 Lightning II . DAS consists of six high-resolution infrared sensors mounted around the F-35's airframe in such a way as to provide unobstructed spherical (4π steradian ) coverage and functions around the aircraft without any pilot input or aiming required. The DAS provides three basic categories of functions in every direction simultaneously: The F-35's DAS

138-491: A capacitor to store the analog voltage at the input, and using an electronic switch or gate to disconnect the capacitor from the input. Many ADC integrated circuits include the sample and hold subsystem internally. An ADC works by sampling the value of the input at discrete intervals in time. Provided that the input is sampled above the Nyquist rate , defined as twice the highest frequency of interest, then all frequencies in

207-437: A digital encoder logic circuit that generates a binary number on the output lines for each voltage range. ADCs of this type have a large die size and high power dissipation. They are often used for video , wideband communications , or other fast signals in optical and magnetic storage . The circuit consists of a resistive divider network, a set of op-amp comparators and a priority encoder. A small amount of hysteresis

276-438: A saw-tooth signal that ramps up or down then quickly returns to zero. When the ramp starts, a timer starts counting. When the ramp voltage matches the input, a comparator fires, and the timer's value is recorded. Timed ramp converters can be implemented economically, however, the ramp time may be sensitive to temperature because the circuit generating the ramp is often a simple analog integrator . A more accurate converter uses

345-798: A semipermeable barrier , such as a dialysis membrane or a hydrogel , or a 3D polymer matrix, which either physically constrains the sensing macromolecule or chemically constrains the macromolecule by bounding it to the scaffold. Neuromorphic sensors are sensors that physically mimic structures and functions of biological neural entities. One example of this is the event camera . The MOSFET invented at Bell Labs between 1955 and 1960, MOSFET sensors (MOS sensors) were later developed, and they have since been widely used to measure physical , chemical , biological and environmental parameters. A number of MOSFET sensors have been developed, for measuring physical , chemical , biological , and environmental parameters. The earliest MOSFET sensors include

414-470: A 500 Hz sine wave. To avoid aliasing, the input to an ADC must be low-pass filtered to remove frequencies above half the sampling rate. This filter is called an anti-aliasing filter , and is essential for a practical ADC system that is applied to analog signals with higher frequency content. In applications where protection against aliasing is essential, oversampling may be used to greatly reduce or even eliminate it. Although aliasing in most systems

483-472: A biological component, such as cells, protein, nucleic acid or biomimetic polymers , are called biosensors . Whereas a non-biological sensor, even organic (carbon chemistry), for biological analytes is referred to as sensor or nanosensor . This terminology applies for both in-vitro and in vivo applications. The encapsulation of the biological component in biosensors, presents a slightly different problem that ordinary sensors; this can either be done by means of

552-447: A certain distance, and where the metal gate is replaced by an ion -sensitive membrane , electrolyte solution and reference electrode . The ISFET is widely used in biomedical applications, such as the detection of DNA hybridization , biomarker detection from blood , antibody detection, glucose measurement, pH sensing, and genetic technology . By the mid-1980s, numerous other MOSFET sensors had been developed, including

621-491: A clocked counter driving a DAC. A special advantage of the ramp-compare system is that converting a second signal just requires another comparator and another register to store the timer value. To reduce sensitivity to input changes during conversion, a sample and hold can charge a capacitor with the instantaneous input voltage and the converter can time the time required to discharge with a constant current . An integrating ADC (also dual-slope or multi-slope ADC) applies

690-525: A constant current source . The time required to discharge the capacitor is proportional to the amplitude of the input voltage. While the capacitor is discharging, pulses from a high-frequency oscillator clock are counted by a register. The number of clock pulses recorded in the register is also proportional to the input voltage. If the analog value to measure is represented by a resistance or capacitance, then by including that element in an RC circuit (with other resistances or capacitances fixed) and measuring

759-432: A faithful reproduction of the original signal is only possible if the sampling rate is higher than twice the highest frequency of the signal. Since a practical ADC cannot make an instantaneous conversion, the input value must necessarily be held constant during the time that the converter performs a conversion (called the conversion time ). An input circuit called a sample and hold performs this task—in most cases by using

SECTION 10

#1732779970912

828-446: A flow of digital values. It is therefore required to define the rate at which new digital values are sampled from the analog signal. The rate of new values is called the sampling rate or sampling frequency of the converter. A continuously varying bandlimited signal can be sampled and then the original signal can be reproduced from the discrete-time values by a reconstruction filter . The Nyquist–Shannon sampling theorem implies that

897-422: A known voltage charging and discharging curve that can be used to solve for an unknown analog value. The Wilkinson ADC was designed by Denys Wilkinson in 1950. The Wilkinson ADC is based on the comparison of an input voltage with that produced by a charging capacitor. The capacitor is allowed to charge until a comparator determines it matches the input voltage. Then, the capacitor is discharged linearly by using

966-436: A longer time to measure than smaller one. And the accuracy is limited by the accuracy of the microcontroller clock and the amount of time available to measure the value, which potentially might even change during measurement or be affected by external parasitics . A direct-conversion or flash ADC has a bank of comparators sampling the input signal in parallel, each firing for a specific voltage range. The comparator bank feeds

1035-409: A pulse of a particular amplitude is always converted to the same digital value. The problem lies in that the ranges of analog values for the digitized values are not all of the same widths, and the differential linearity decreases proportionally with the divergence from the average width. The sliding scale principle uses an averaging effect to overcome this phenomenon. A random, but known analog voltage

1104-454: A sampler. It cannot improve the linearity, and thus accuracy does not necessarily improve. Quantization distortion in an audio signal of very low level with respect to the bit depth of the ADC is correlated with the signal and sounds distorted and unpleasant. With dithering, the distortion is transformed into noise. The undistorted signal may be recovered accurately by averaging over time. Dithering

1173-519: A sampling rate greater than twice the bandwidth of the signal, then per the Nyquist–Shannon sampling theorem , near-perfect reconstruction is possible. The presence of quantization error limits the SNDR of even an ideal ADC. However, if the SNDR of the ADC exceeds that of the input signal, then the effects of quantization error may be neglected, resulting in an essentially perfect digital representation of

1242-405: Is a random error that can be reduced by signal processing , such as filtering, usually at the expense of the dynamic behavior of the sensor. The sensor resolution or measurement resolution is the smallest change that can be detected in the quantity that is being measured. The resolution of a sensor with a digital output is usually the numerical resolution of the digital output. The resolution

1311-430: Is a system that converts an analog signal , such as a sound picked up by a microphone or light entering a digital camera , into a digital signal . An ADC may also provide an isolated measurement such as an electronic device that converts an analog input voltage or current to a digital number representing the magnitude of the voltage or current. Typically the digital output is a two's complement binary number that

1380-454: Is a very small amount of random noise (e.g. white noise ), which is added to the input before conversion. Its effect is to randomize the state of the LSB based on the signal. Rather than the signal simply getting cut off altogether at low levels, it extends the effective range of signals that the ADC can convert, at the expense of a slight increase in noise. Dither can only increase the resolution of

1449-535: Is added to the sampled input voltage. It is then converted to digital form, and the equivalent digital amount is subtracted, thus restoring it to its original value. The advantage is that the conversion has taken place at a random point. The statistical distribution of the final levels is decided by a weighted average over a region of the range of the ADC. This in turn desensitizes it to the width of any specific level. These are several common ways of implementing an electronic ADC. Resistor-capacitor (RC) circuits have

SECTION 20

#1732779970912

1518-471: Is also used in integrating systems such as electricity meters . Since the values are added together, the dithering produces results that are more exact than the LSB of the analog-to-digital converter. Dither is often applied when quantizing photographic images to a fewer number of bits per pixel—the image becomes noisier but to the eye looks far more realistic than the quantized image, which otherwise becomes banded . This analogous process may help to visualize

1587-428: Is built into the comparator to resolve any problems at voltage boundaries. At each node of the resistive divider, a comparison voltage is available. The purpose of the circuit is to compare the analog input voltage with each of the node voltages. The circuit has the advantage of high speed as the conversion takes place simultaneously rather than sequentially. Typical conversion time is 100 ns or less. Conversion time

1656-443: Is correlated with the concentration of a certain chemical species (termed as analyte ). Two main steps are involved in the functioning of a chemical sensor, namely, recognition and transduction . In the recognition step, analyte molecules interact selectively with receptor molecules or sites included in the structure of the recognition element of the sensor. Consequently, a characteristic physical parameter varies and this variation

1725-427: Is limited only by the speed of the comparator and of the priority encoder. This type of ADC has the disadvantage that the number of comparators required almost doubles for each added bit. Also, the larger the value of n, the more complex is the priority encoder. A successive-approximation ADC uses a comparator and a binary search to successively narrow a range that contains the input voltage. At each successive step,

1794-467: Is proportional to the input, but there are other possibilities. There are several ADC architectures . Due to the complexity and the need for precisely matched components , all but the most specialized ADCs are implemented as integrated circuits (ICs). These typically take the form of metal–oxide–semiconductor (MOS) mixed-signal integrated circuit chips that integrate both analog and digital circuits . A digital-to-analog converter (DAC) performs

1863-420: Is related to the precision with which the measurement is made, but they are not the same thing. A sensor's accuracy may be considerably worse than its resolution. A chemical sensor is a self-contained analytical device that can provide information about the chemical composition of its environment, that is, a liquid or a gas phase . The information is provided in the form of a measurable physical signal that

1932-560: Is reported by means of an integrated transducer that generates the output signal. A chemical sensor based on recognition material of biological nature is a biosensor . However, as synthetic biomimetic materials are going to substitute to some extent recognition biomaterials, a sharp distinction between a biosensor and a standard chemical sensor is superfluous. Typical biomimetic materials used in sensor development are molecularly imprinted polymers and aptamers . In biomedicine and biotechnology , sensors which detect analytes thanks to

2001-459: Is the ADC's resolution in bits and E FSR is the full-scale voltage range (also called 'span'). E FSR is given by where V RefHi and V RefLow are the upper and lower extremes, respectively, of the voltages that can be coded. Normally, the number of voltage intervals is given by where M is the ADC's resolution in bits. That is, one voltage interval is assigned in between two consecutive code levels. Example: In many cases,

2070-570: Is the basis for modern image sensors , including the charge-coupled device (CCD) and the CMOS active-pixel sensor (CMOS sensor), used in digital imaging and digital cameras . Willard Boyle and George E. Smith developed the CCD in 1969. While researching the MOS process, they realized that an electric charge was the analogy of the magnetic bubble and that it could be stored on a tiny MOS capacitor. As it

2139-414: Is the number of ADC bits. Clock jitter is caused by phase noise . The resolution of ADCs with a digitization bandwidth between 1 MHz and 1 GHz is limited by jitter. For lower bandwidth conversions such as when sampling audio signals at 44.1 kHz, clock jitter has a less significant impact on performance. An analog signal is continuous in time and it is necessary to convert this to

AN/AAQ-37 Distributed Aperture System - Misplaced Pages Continue

2208-407: Is uniformly distributed between − 1 ⁄ 2 LSB and + 1 ⁄ 2 LSB, and the signal has a uniform distribution covering all quantization levels, the signal-to-quantization-noise ratio (SQNR) is given by where Q is the number of quantization bits. For example, for a 16-bit ADC, the quantization error is 96.3 dB below the maximum level. Quantization error is distributed from DC to

2277-404: Is unwanted, it can be exploited to provide simultaneous down-mixing of a band-limited high-frequency signal (see undersampling and frequency mixer ). The alias is effectively the lower heterodyne of the signal frequency and sampling frequency. For economy, signals are often sampled at the minimum rate required with the result that the quantization error introduced is white noise spread over

2346-479: The Nyquist frequency . Consequently, if part of the ADC's bandwidth is not used, as is the case with oversampling , some of the quantization error will occur out-of-band , effectively improving the SQNR for the bandwidth in use. In an oversampled system, noise shaping can be used to further increase SQNR by forcing more quantization error out of band. In ADCs, performance can usually be improved using dither . This

2415-470: The bandlimited analog input signal. The resolution of the converter indicates the number of different, i.e. discrete, values it can produce over the allowed range of analog input values. Thus a particular resolution determines the magnitude of the quantization error and therefore determines the maximum possible signal-to-noise ratio for an ideal ADC without the use of oversampling . The input samples are usually stored electronically in binary form within

2484-463: The effective number of bits (ENOB) below that predicted by quantization error alone. The error is zero for DC, small at low frequencies, but significant with signals of high amplitude and high frequency. The effect of jitter on performance can be compared to quantization error: Δ t < 1 2 q π f 0 {\displaystyle \Delta t<{\frac {1}{2^{q}\pi f_{0}}}} , where q

2553-534: The gas sensor FET (GASFET), surface accessible FET (SAFET), charge flow transistor (CFT), pressure sensor FET (PRESSFET), chemical field-effect transistor (ChemFET), reference ISFET (REFET), biosensor FET (BioFET), enzyme-modified FET (ENFET) and immunologically modified FET (IMFET). By the early 2000s, BioFET types such as the DNA field-effect transistor (DNAFET), gene-modified FET (GenFET) and cell-potential BioFET (CPFET) had been developed. MOS technology

2622-408: The signal-to-noise ratio performance of the ADC and thus reduce its effective resolution. When digitizing a sine wave x ( t ) = A sin ⁡ ( 2 π f 0 t ) {\displaystyle x(t)=A\sin {(2\pi f_{0}t)}} , the use of a non-ideal sampling clock will result in some uncertainty in when samples are recorded. Provided that

2691-421: The ADC, so the resolution is usually expressed as the audio bit depth . In consequence, the number of discrete values available is usually a power of two. For example, an ADC with a resolution of 8 bits can encode an analog input to one in 256 different levels (2  = 256). The values can represent the ranges from 0 to 255 (i.e. as unsigned integers) or from −128 to 127 (i.e. as signed integer), depending on

2760-519: The actual sampling time uncertainty due to clock jitter is Δ t {\displaystyle \Delta t} , the error caused by this phenomenon can be estimated as E a p ≤ | x ′ ( t ) Δ t | ≤ 2 A π f 0 Δ t {\displaystyle E_{ap}\leq |x'(t)\Delta t|\leq 2A\pi f_{0}\Delta t} . This will result in additional recorded noise that will reduce

2829-409: The application. Resolution can also be defined electrically, and expressed in volts . The change in voltage required to guarantee a change in the output code level is called the least significant bit (LSB) voltage. The resolution Q of the ADC is equal to the LSB voltage. The voltage resolution of an ADC is equal to its overall voltage measurement range divided by the number of intervals: where M

AN/AAQ-37 Distributed Aperture System - Misplaced Pages Continue

2898-419: The conversion periodically, sampling the input, and limiting the allowable bandwidth of the input signal. The performance of an ADC is primarily characterized by its bandwidth and signal-to-noise and distortion ratio (SNDR). The bandwidth of an ADC is characterized primarily by its sampling rate . The SNDR of an ADC is influenced by many factors, including the resolution , linearity and accuracy (how well

2967-415: The converter compares the input voltage to the output of an internal digital-to-analog converter (DAC) which initially represents the midpoint of the allowed input voltage range. At each step in this process, the approximation is stored in a successive approximation register (SAR) and the output of the digital-to-analog converter is updated for a comparison over a narrower range. A ramp-compare ADC produces

3036-417: The effect of dither on an analog audio signal that is converted to digital. An ADC has several sources of errors. Quantization error and (assuming the ADC is intended to be linear) non- linearity are intrinsic to any analog-to-digital conversion. These errors are measured in a unit called the least significant bit (LSB). In the above example of an eight-bit ADC, an error of one LSB is 1 ⁄ 256 of

3105-410: The following rules: Most sensors have a linear transfer function . The sensitivity is then defined as the ratio between the output signal and measured property. For example, if a sensor measures temperature and has a voltage output, the sensitivity is constant with the units [V/K]. The sensitivity is the slope of the transfer function. Converting the sensor's electrical output (for example V) to

3174-499: The full signal range, or about 0.4%. All ADCs suffer from nonlinearity errors caused by their physical imperfections, causing their output to deviate from a linear function (or some other function, in the case of a deliberately nonlinear ADC) of their input. These errors can sometimes be mitigated by calibration , or prevented by testing. Important parameters for linearity are integral nonlinearity and differential nonlinearity . These nonlinearities introduce distortion that can reduce

3243-403: The helmet. A DAS test system has also been used to track tank gun firing, but this is "not an F-35 requirement". The DAS has been produced by Raytheon since 2018 after Northrop Grumman decided not to participate in a follow on competition. Sensor In the broadest definition, a sensor is a device, module, machine, or subsystem that detects events or changes in its environment and sends

3312-439: The increasing demand for rapid, affordable and reliable information in today's world, disposable sensors—low-cost and easy‐to‐use devices for short‐term monitoring or single‐shot measurements—have recently gained growing importance. Using this class of sensors, critical analytical information can be obtained by anyone, anywhere and at any time, without the need for recalibration and worrying about contamination. A good sensor obeys

3381-414: The information to other electronics, frequently a computer processor. Sensors are used in everyday objects such as touch-sensitive elevator buttons ( tactile sensor ) and lamps which dim or brighten by touching the base, and in innumerable applications of which most people are never aware. With advances in micromachinery and easy-to-use microcontroller platforms, the uses of sensors have expanded beyond

3450-414: The input quantity it measures changes. For instance, if the mercury in a thermometer moves 1  cm when the temperature changes by 1 °C, its sensitivity is 1 cm/°C (it is basically the slope dy/dx assuming a linear characteristic). Some sensors can also affect what they measure; for instance, a room temperature thermometer inserted into a hot cup of liquid cools the liquid while the liquid heats

3519-494: The logarithm of the resolution, i.e. the number of bits. Flash ADCs are certainly the fastest type of the three; The conversion is basically performed in a single parallel step. There is a potential tradeoff between speed and precision. Flash ADCs have drifts and uncertainties associated with the comparator levels results in poor linearity. To a lesser extent, poor linearity can also be an issue for successive-approximation ADCs. Here, nonlinearity arises from accumulating errors from

SECTION 50

#1732779970912

3588-754: The measured units (for example K) requires dividing the electrical output by the slope (or multiplying by its reciprocal). In addition, an offset is frequently added or subtracted. For example, −40 must be added to the output if 0 V output corresponds to −40 C input. For an analog sensor signal to be processed or used in digital equipment, it needs to be converted to a digital signal, using an analog-to-digital converter . Since sensors cannot replicate an ideal transfer function , several types of deviations can occur which limit sensor accuracy : All these deviations can be classified as systematic errors or random errors . Systematic errors can sometimes be compensated for by means of some kind of calibration strategy. Noise

3657-406: The open-gate field-effect transistor (OGFET) introduced by Johannessen in 1970, the ion-sensitive field-effect transistor (ISFET) invented by Piet Bergveld in 1970, the adsorption FET (ADFET) patented by P.F. Cox in 1974, and a hydrogen -sensitive MOSFET demonstrated by I. Lundstrom, M.S. Shivaraman, C.S. Svenson and L. Lundkvist in 1975. The ISFET is a special type of MOSFET with a gate at

3726-410: The performance of the ADC can be greatly increased at little or no cost. Furthermore, as any aliased signals are also typically out of band, aliasing can often be eliminated using very low cost filters. The speed of an ADC varies by type. The Wilkinson ADC is limited by the clock rate which is processable by current digital circuits. For a successive-approximation ADC , the conversion time scales with

3795-411: The quantization levels match the true analog signal), aliasing and jitter . The SNDR of an ADC is often summarized in terms of its effective number of bits (ENOB), the number of bits of each measure it returns that are on average not noise . An ideal ADC has an ENOB equal to its resolution. ADCs are chosen to match the bandwidth and required SNDR of the signal to be digitized. If an ADC operates at

3864-410: The reverse function; it converts a digital signal into an analog signal. An ADC converts a continuous-time and continuous-amplitude analog signal to a discrete-time and discrete-amplitude digital signal . The conversion involves quantization of the input, so it necessarily introduces a small amount of quantization error . Furthermore, instead of continuously performing the conversion, an ADC does

3933-504: The signal can be reconstructed. If frequencies above half the Nyquist rate are sampled, they are incorrectly detected as lower frequencies, a process referred to as aliasing. Aliasing occurs because instantaneously sampling a function at two or fewer times per cycle results in missed cycles, and therefore the appearance of an incorrectly lower frequency. For example, a 2 kHz sine wave being sampled at 1.5 kHz would be reconstructed as

4002-406: The subtraction processes. Wilkinson ADCs have the best linearity of the three. The sliding scale or randomizing method can be employed to greatly improve the linearity of any type of ADC, but especially flash and successive approximation types. For any ADC the mapping from input voltage to digital output value is not exactly a floor or ceiling function as it should be. Under normal conditions,

4071-461: The thermometer. Sensors are usually designed to have a small effect on what is measured; making the sensor smaller often improves this and may introduce other advantages. Technological progress allows more and more sensors to be manufactured on a microscopic scale as microsensors using MEMS technology. In most cases, a microsensor reaches a significantly faster measurement time and higher sensitivity compared with macroscopic approaches. Due to

4140-415: The time it takes to charge (and/or discharge) its capacitor from 1 ⁄ 3   V supply to 2 ⁄ 3   V supply . By sending this pulse into a microcontroller with an accurate clock, the duration of the pulse can be measured and converted using the capacitor charging equation to produce the value of the unknown resistance or capacitance. Larger resistances and capacitances will take

4209-550: The time to charge the capacitance from a known starting voltage to another known ending voltage through the resistance from a known voltage supply, the value of the unknown resistance or capacitance can be determined using the capacitor charging equation: V capacitor ( t ) = V supply ( 1 − e − t R C ) {\displaystyle V_{\text{capacitor}}(t)=V_{\text{supply}}\left(1-e^{-{\frac {t}{RC}}}\right)} and solving for

SECTION 60

#1732779970912

4278-689: The traditional fields of temperature, pressure and flow measurement, for example into MARG sensors . Analog sensors such as potentiometers and force-sensing resistors are still widely used. Their applications include manufacturing and machinery, airplanes and aerospace, cars, medicine, robotics and many other aspects of our day-to-day life. There is a wide range of other sensors that measure chemical and physical properties of materials, including optical sensors for refractive index measurement, vibrational sensors for fluid viscosity measurement, and electro-chemical sensors for monitoring pH of fluids. A sensor's sensitivity indicates how much its output changes when

4347-411: The unknown input voltage to the input of an integrator and allows the voltage to ramp for a fixed time period (the run-up period). Then a known reference voltage of opposite polarity is applied to the integrator and is allowed to ramp until the integrator output returns to zero (the run-down period). The input voltage is computed as a function of the reference voltage, the constant run-up time period, and

4416-471: The unknown resistance or capacitance using those starting and ending datapoints. This is similar but contrasts to the Wilkinson ADC which measures an unknown voltage with a known resistance and capacitance, by instead measuring an unknown resistance or capacitance with a known voltage. For example, the positive (and/or negative) pulse width from a 555 Timer IC in monostable or astable mode represents

4485-418: The useful resolution of a converter is limited by the signal-to-noise ratio (SNR) and other errors in the overall system expressed as an ENOB. Quantization error is introduced by the quantization inherent in an ideal ADC. It is a rounding error between the analog input voltage to the ADC and the output digitized value. The error is nonlinear and signal-dependent. In an ideal ADC, where the quantization error

4554-433: The whole passband of the converter. If a signal is sampled at a rate much higher than the Nyquist rate and then digitally filtered to limit it to the signal bandwidth produces the following advantages: Oversampling is typically used in audio frequency ADCs where the required sampling rate (typically 44.1 or 48 kHz) is very low compared to the clock speed of typical transistor circuits (>1 MHz). In this case,

4623-431: Was fairly straightforward to fabricate a series of MOS capacitors in a row, they connected a suitable voltage to them so that the charge could be stepped along from one to the next. The CCD is a semiconductor circuit that was later used in the first digital video cameras for television broadcasting . The MOS active-pixel sensor (APS) was developed by Tsutomu Nakamura at Olympus in 1985. The CMOS active-pixel sensor

4692-547: Was flown in military operational exercises in 2011, has demonstrated the ability to detect and track ballistic missiles to ranges exceeding 800 miles (1,300 km), and has also demonstrated the ability to detect and track multiple small suborbital rockets simultaneously in flight. The AN/AAQ-37 DAS was designed and produced by Northrop Grumman . The current sensors used in the system may have insufficient night acuity for pilots used to flying with night vision goggles (NVG), and are therefore augmented by an embedded NVG camera in

4761-1190: Was later developed by Eric Fossum and his team in the early 1990s. MOS image sensors are widely used in optical mouse technology. The first optical mouse, invented by Richard F. Lyon at Xerox in 1980, used a 5   μm NMOS sensor chip. Since the first commercial optical mouse, the IntelliMouse introduced in 1999, most optical mouse devices use CMOS sensors. MOS monitoring sensors are used for house monitoring , office and agriculture monitoring, traffic monitoring (including car speed , traffic jams , and traffic accidents ), weather monitoring (such as for rain , wind , lightning and storms ), defense monitoring, and monitoring temperature , humidity , air pollution , fire , health , security and lighting . MOS gas detector sensors are used to detect carbon monoxide , sulfur dioxide , hydrogen sulfide , ammonia , and other gas substances. Other MOS sensors include intelligent sensors and wireless sensor network (WSN) technology. Analog-to-digital converter In electronics , an analog-to-digital converter ( ADC , A/D , or A-to-D )

#911088