Misplaced Pages

Autolite

Article snapshot taken from Wikipedia with creative commons attribution-sharealike license. Give it a read and then ask your questions in the chat. We can research this topic together.

Autolite or Auto–Lite is an American brand of spark plugs and ignition wire sets headquartered in Cleveland, Ohio . Autolite products are sold in the United States , Canada , Mexico , and Australia . Until 2011, the Autolite brand was a part of Honeywell 's automotive Consumer Products Group, along with FRAM and Prestone. Since then, it has been manufactured and marketed by FRAM Group. Autolite has been the official spark plug of NASCAR since April 2000.

#831168

71-596: The origins of Autolite are traced to 1911, when Electric Autolite was founded. The company produced generators to power early day buggy lamps. In 1927, Electric Autolite acquired the Prest–O–Lite Battery Company from The Union Carbide Corporation which produced automotive batteries. In 1934, an Autolite facility in Toledo, Ohio was the site of the Auto-Lite strike . In 1935, Royce G. Martin, President of

142-459: A generator is a device that converts motion-based power ( potential and kinetic energy ) or fuel-based power ( chemical energy ) into electric power for use in an external circuit . Sources of mechanical energy include steam turbines , gas turbines , water turbines , internal combustion engines , wind turbines and even hand cranks . The first electromagnetic generator, the Faraday disk ,

213-653: A steam power plant . The first practical design was the AVCO Mk. 25, developed in 1965. The U.S. government funded substantial development, culminating in a 25 MW demonstration plant in 1987. In the Soviet Union from 1972 until the late 1980s, the MHD plant U 25 was in regular utility operation on the Moscow power system with a rating of 25 MW, the largest MHD plant rating in the world at that time. MHD generators operated as

284-698: A topping cycle are currently (2007) less efficient than combined cycle gas turbines . Induction AC motors may be used as generators, turning mechanical energy into electric current. Induction generators operate by mechanically turning their rotor faster than the simultaneous speed, giving negative slip. A regular AC non-simultaneous motor usually can be used as a generator, without any changes to its parts. Induction generators are useful in applications like minihydro power plants, wind turbines, or in reducing high-pressure gas streams to lower pressure, because they can recover energy with relatively simple controls. They do not require another circuit to start working because

355-485: A 1940 promotional film, Autolite featured stop motion animation of its products marching past Autolite factories to the tune of Franz Schubert 's Military March . An abbreviated version of this sequence was later used in television ads for Autolite. Announcer Harlow Wilcox turned the ad's tagline "You're always right with Autolite!" into a national catchphrase. In 1961, the Ford Motor Company acquired

426-479: A British electrician, J. E. H. Gordon , in 1882. The first public demonstration of an "alternator system" was given by William Stanley Jr. , an employee of Westinghouse Electric in 1886. Sebastian Ziani de Ferranti established Ferranti, Thompson and Ince in 1882, to market his Ferranti-Thompson Alternator , invented with the help of renowned physicist Lord Kelvin . His early alternators produced frequencies between 100 and 300 Hz . Ferranti went on to design

497-406: A body or system is subjected only to conservative forces , the mechanical energy of that body or system remains constant. The difference between a conservative and a non-conservative force is that when a conservative force moves an object from one point to another, the work done by the conservative force is independent of the path. On the contrary, when a non-conservative force acts upon an object,

568-408: A certain amount of work done against friction resulted in a definite quantity of heat which should be conceived as the random motions of the particles that comprise matter. This equivalence between mechanical energy and heat is especially important when considering colliding objects. In an elastic collision , mechanical energy is conserved – the sum of the mechanical energies of the colliding objects

639-436: A foot pump, such generators can be practically used to charge batteries, and in some cases are designed with an integral inverter. An average "healthy human" can produce a steady 75 watts (0.1 horsepower) for a full eight hour period, while a "first class athlete" can produce approximately 298 watts (0.4 horsepower) for a similar period, at the end of which an undetermined period of rest and recovery will be required. At 298 watts,

710-456: A generator and load is shown in the adjacent diagram. The generator is represented by an abstract generator consisting of an ideal voltage source and an internal impedance. The generator's V G {\displaystyle V_{\text{G}}} and R G {\displaystyle R_{\text{G}}} parameters can be determined by measuring the winding resistance (corrected to operating temperature ), and measuring

781-430: A generator consists of a rotating part and a stationary part which together form a magnetic circuit : One of these parts generates a magnetic field, the other has a wire winding in which the changing field induces an electric current: The armature can be on either the rotor or the stator, depending on the design, with the field coil or magnet on the other part. Before the connection between magnetism and electricity

SECTION 10

#1732802302832

852-449: A magnetic field produces a current which changes direction with each 180° rotation, an alternating current (AC). However many early uses of electricity required direct current (DC). In the first practical electric generators, called dynamos , the AC was converted into DC with a commutator , a set of rotating switch contacts on the armature shaft. The commutator reversed the connection of

923-403: A million amperes , because the homopolar generator can be made to have very low internal resistance. A magnetohydrodynamic generator directly extracts electric power from moving hot gases through a magnetic field, without the use of rotating electromagnetic machinery. MHD generators were originally developed because the output of a plasma MHD generator is a flame, well able to heat the boilers of

994-488: A series of discoveries, the dynamo was succeeded by many later inventions, especially the AC alternator , which was capable of generating alternating current . It is commonly known to be the Synchronous Generators (SGs). The synchronous machines are directly connected to the grid and need to be properly synchronized during startup. Moreover, they are excited with special control to enhance the stability of

1065-438: A sliding magnet moves back and forth through a solenoid , a copper wire or a coil. An alternating current is induced in the wire, or loops of wire, by Faraday's law of induction each time the magnet slides through. This type of generator is used in the Faraday flashlight . Larger linear electricity generators are used in wave power schemes. Grid-connected generators deliver power at a constant frequency. For generators of

1136-434: A small DC voltage . This design was inefficient, due to self-cancelling counterflows of current in regions of the disk that were not under the influence of the magnetic field. While current was induced directly underneath the magnet, the current would circulate backwards in regions that were outside the influence of the magnetic field. This counterflow limited the power output to the pickup wires and induced waste heating of

1207-450: A stable power supply. Electric scooters with regenerative braking have become popular all over the world. Engineers use kinetic energy recovery systems on the scooter to reduce energy consumption and increase its range up to 40-60% by simply recovering energy using the magnetic brake, which generates electric energy for further use. Modern vehicles reach speed up to 25–30 km/h and can run up to 35–40 km. An engine-generator

1278-461: A system is the sum of the potential energy (which is measured by the position of the parts of the system) and the kinetic energy (which is also called the energy of motion): E mechanical = U + K {\displaystyle E_{\text{mechanical}}=U+K} The potential energy, U , depends on the position of an object subjected to gravity or some other conservative force . The gravitational potential energy of an object

1349-417: A water- or wind-powered generator to trickle-charge the batteries. A small propeller , wind turbine or turbine is connected to a low-power generator to supply currents at typical wind or cruising speeds. Recreational vehicles need an extra power supply to power their onboard accessories, including air conditioning units, and refrigerators. An RV power plug is connected to the electric generator to obtain

1420-562: Is an industrial facility that generates electricity . Most power stations contain one or more generators, or spinning machines converting mechanical power into three-phase electrical power . The relative motion between a magnetic field and a conductor creates an electric current . The energy source harnessed to turn the generator varies widely. Most power stations in the world burn fossil fuels such as coal , oil , and natural gas to generate electricity. Cleaner sources include nuclear power , and increasingly use renewables such as

1491-406: Is equal to the weight W of the object multiplied by the height h of the object's center of gravity relative to an arbitrary datum: U = W h {\displaystyle U=Wh} The potential energy of an object can be defined as the object's ability to do work and is increased as the object is moved in the opposite direction of the direction of the force. If F represents

SECTION 20

#1732802302832

1562-722: Is in circular orbit, the energy conservation equation can be further simplified into E mechanical = − G M m 2 r {\displaystyle E_{\text{mechanical}}=-G{\frac {Mm}{2r}}} since in circular motion, Newton's 2nd Law of motion can be taken to be G M m r 2   = m v 2 r {\displaystyle G{\frac {Mm}{r^{2}}}\ ={\frac {mv^{2}}{r}}} Today, many technological devices convert mechanical energy into other forms of energy or vice versa. These devices can be placed in these categories: The classification of energy into different types often follows

1633-497: Is provided by one or more electromagnets, which are usually called field coils. Large power generation dynamos are now rarely seen due to the now nearly universal use of alternating current for power distribution. Before the adoption of AC, very large direct-current dynamos were the only means of power generation and distribution. AC has come to dominate due to the ability of AC to be easily transformed to and from very high voltages to permit low losses over large distances. Through

1704-415: Is self- excited , i.e. its field electromagnets are powered by the machine's own output. Other types of DC generators use a separate source of direct current to energise their field magnets. A homopolar generator is a DC electrical generator comprising an electrically conductive disc or cylinder rotating in a plane perpendicular to a uniform static magnetic field. A potential difference is created between

1775-405: Is the ability to independently supply electricity, allowing the units to serve as backup power sources. A generator can also be driven by human muscle power (for instance, in field radio station equipment). Human powered electric generators are commercially available, and have been the project of some DIY enthusiasts. Typically operated by means of pedal power, a converted bicycle trainer, or

1846-485: Is the combination of an electrical generator and an engine ( prime mover ) mounted together to form a single piece of self-contained equipment. The engines used are usually piston engines, but gas turbines can also be used, and there are even hybrid diesel-gas units, called dual-fuel units. Many different versions of engine-generators are available – ranging from very small portable petrol powered sets to large turbine installations. The primary advantage of engine-generators

1917-430: Is the same before and after the collision. After an inelastic collision , however, the mechanical energy of the system will have changed. Usually, the mechanical energy before the collision is greater than the mechanical energy after the collision. In inelastic collisions, some of the mechanical energy of the colliding objects is transformed into kinetic energy of the constituent particles. This increase in kinetic energy of

1988-420: Is the sum of potential energy and kinetic energy . The principle of conservation of mechanical energy states that if an isolated system is subject only to conservative forces , then the mechanical energy is constant. If an object moves in the opposite direction of a conservative net force, the potential energy will increase; and if the speed (not the velocity ) of the object changes, the kinetic energy of

2059-805: The Deptford Power Station for the London Electric Supply Corporation in 1887 using an alternating current system. On its completion in 1891, it was the first truly modern power station, supplying high-voltage AC power that was then "stepped down" for consumer use on each street. This basic system remains in use today around the world. After 1891, polyphase alternators were introduced to supply currents of multiple differing phases. Later alternators were designed for varying alternating-current frequencies between sixteen and about one hundred hertz, for use with arc lighting, incandescent lighting and electric motors. As

2130-671: The Air ), medical and other needs in remote stations and towns. A tachogenerator is an electromechanical device which produces an output voltage proportional to its shaft speed. It may be used for a speed indicator or in a feedback speed control system. Tachogenerators are frequently used to power tachometers to measure the speeds of electric motors, engines, and the equipment they power. Generators generate voltage roughly proportional to shaft speed. With precise construction and design, generators can be built to produce very precise voltages for certain ranges of shaft speeds. An equivalent circuit of

2201-581: The Autolite trade name, an Ohio spark plug factory, a Michigan battery facility, limited distribution rights, and the services of several employees. Autolite products became standard original factory equipment in Ford vehicles. A federal antitrust lawsuit was filed against Ford, which dragged on through the remainder of the 1960s, ultimately being decided in 1972 by the Supreme Court against Ford, and Ford

Autolite - Misplaced Pages Continue

2272-638: The Electric Autolite Company, decided the company should enter the business of manufacturing spark plugs. Robert Twells, a ceramic engineer, led the development team. In 1936, the first spark plug was produced at their Fostoria, Ohio plant. A few months later, the company sold their first spark plug . Electric Autolite's products were expanded further to include starter motors , ignition systems , and wire and cable products. Autolite had secured supply contracts with leading car manufacturers such as Chrysler , Studebaker , and Packard . In

2343-478: The armature winding to the circuit every 180° rotation of the shaft, creating a pulsing DC current. One of the first dynamos was built by Hippolyte Pixii in 1832. The dynamo was the first electrical generator capable of delivering power for industry. The Woolrich Electrical Generator of 1844, now in Thinktank, Birmingham Science Museum , is the earliest electrical generator used in an industrial process. It

2414-436: The armature winding. When the generator first starts to turn, the small amount of remanent magnetism present in the iron core provides a magnetic field to get it started, generating a small current in the armature. This flows through the field coils, creating a larger magnetic field which generates a larger armature current. This "bootstrap" process continues until the magnetic field in the core levels off due to saturation and

2485-402: The assistance of power electronic devices, these can regulate the output frequency to a desired value over a wider range of generator shaft speeds. Alternatively, a standard generator can be used with no attempt to regulate frequency, and the resulting power converted to the desired output frequency with a rectifier and converter combination. Allowing a wider range of prime mover speeds can improve

2556-464: The average "healthy human" becomes exhausted within 10 minutes. The net electrical power that can be produced will be less, due to the efficiency of the generator. Portable radio receivers with a crank are made to reduce battery purchase requirements, see clockwork radio . During the mid 20th century, pedal powered radios were used throughout the Australian outback , to provide schooling ( School of

2627-409: The bicycle's tire on an as-needed basis, and hub dynamos which are directly attached to the bicycle's drive train. The name is conventional as they are small permanent-magnet alternators, not self-excited DC machines as are dynamos . Some electric bicycles are capable of regenerative braking , where the drive motor is used as a generator to recover some energy during braking. Sailing boats may use

2698-597: The center of the disc and the rim (or ends of the cylinder), the electrical polarity depending on the direction of rotation and the orientation of the field. It is also known as a unipolar generator , acyclic generator , disk dynamo , or Faraday disc . The voltage is typically low, on the order of a few volts in the case of small demonstration models, but large research generators can produce hundreds of volts, and some systems have multiple generators in series to produce an even larger voltage. They are unusual in that they can produce tremendous electric current, some more than

2769-505: The centre of Earth possesses both kinetic energy, K {\displaystyle K} , (by virtue of its motion) and gravitational potential energy, U {\displaystyle U} , (by virtue of its position within the Earth's gravitational field; Earth's mass is M {\displaystyle M} ). Hence, mechanical energy E mechanical {\displaystyle E_{\text{mechanical}}} of

2840-490: The conservative force and x the position, the potential energy of the force between the two positions x 1 and x 2 is defined as the negative integral of F from x 1 to x 2 : U = − ∫ x 1 x 2 F → ⋅ d x → {\displaystyle U=-\int _{x_{1}}^{x_{2}}{\vec {F}}\cdot d{\vec {x}}} The kinetic energy, K , depends on

2911-460: The constituent particles is perceived as an increase in temperature. The collision can be described by saying some of the mechanical energy of the colliding objects has been converted into an equal amount of heat. Thus, the total energy of the system remains unchanged though the mechanical energy of the system has reduced. A satellite of mass m {\displaystyle m} at a distance r {\displaystyle r} from

Autolite - Misplaced Pages Continue

2982-436: The copper disc. Later homopolar generators would solve this problem by using an array of magnets arranged around the disc perimeter to maintain a steady field effect in one current-flow direction. Another disadvantage was that the output voltage was very low, due to the single current path through the magnetic flux. Experimenters found that using multiple turns of wire in a coil could produce higher, more useful voltages. Since

3053-407: The difficulty of insulating machines that produced very high voltages, electrostatic generators had low power ratings, and were never used for generation of commercially significant quantities of electric power. Their only practical applications were to power early X-ray tubes , and later in some atomic particle accelerators . The operating principle of electromagnetic generators was discovered in

3124-413: The first major industrial uses of electricity. For example, in the 1870s Siemens used electromagnetic dynamos to power electric arc furnaces for the production of metals and other materials. The dynamo machine that was developed consisted of a stationary structure, which provides the magnetic field, and a set of rotating windings which turn within that field. On larger machines the constant magnetic field

3195-409: The frictional forces into account, the system loses mechanical energy with each swing because of the negative work done on the pendulum by these non-conservative forces. That the loss of mechanical energy in a system always resulted in an increase of the system's temperature has been known for a long time, but it was the amateur physicist James Prescott Joule who first experimentally demonstrated how

3266-476: The generator reaches a steady state power output. Very large power station generators often utilize a separate smaller generator to excite the field coils of the larger. In the event of a severe widespread power outage where islanding of power stations has occurred, the stations may need to perform a black start to excite the fields of their largest generators, in order to restore customer power service. A dynamo uses commutators to produce direct current. It

3337-485: The object also changes. In all real systems, however, nonconservative forces , such as frictional forces , will be present, but if they are of negligible magnitude , the mechanical energy changes little and its conservation is a useful approximation. In elastic collisions , the kinetic energy is conserved, but in inelastic collisions some mechanical energy may be converted into thermal energy . The equivalence between lost mechanical energy and an increase in temperature

3408-421: The open-circuit and loaded voltage for a defined current load. This is the simplest model of a generator, further elements may need to be added for an accurate representation. In particular, inductance can be added to allow for the machine's windings and magnetic leakage flux, but a full representation can become much more complex than this. Mechanical energy In physical sciences , mechanical energy

3479-575: The operations and the transfer of ownership of the acquired trademarks. Autolite Spark Plugs are manufactured by FRAM Group, a company that also offers oil, air, fuel filters, as well as PCV valves and transmission modulators. FRAM Group is a subsidiary of the Rank Group, a New Zealand –based private investment company owned by Graeme Hart , formerly the richest person in New Zealand. The manufacturing location of Autolite Spark Plugs depends on

3550-413: The output voltage is proportional to the number of turns, generators could be easily designed to produce any desired voltage by varying the number of turns. Wire windings became a basic feature of all subsequent generator designs. Independently of Faraday, Ányos Jedlik started experimenting in 1827 with the electromagnetic rotating devices which he called electromagnetic self-rotors . In the prototype of

3621-443: The overall energy production of an installation, at the cost of more complex generators and controls. For example, where a wind turbine operating at fixed frequency might be required to spill energy at high wind speeds, a variable speed system can allow recovery of energy contained during periods of high wind speed. A power station , also known as a power plant or powerhouse and sometimes generating station or generating plant ,

SECTION 50

#1732802302832

3692-472: The power system. Alternating current generating systems were known in simple forms from Michael Faraday 's original discovery of the magnetic induction of electric current . Faraday himself built an early alternator. His machine was a "rotating rectangle", whose operation was heteropolar : each active conductor passed successively through regions where the magnetic field was in opposite directions. Large two-phase alternating current generators were built by

3763-827: The product line they are producing and the market demand they want to meet. But most of the manufacturing of Autolite Spark Plugs takes place in China , where FRAM GROUP OPERATIONS LLC Imports from SHANGHAI SWEET AUTO PARTS COLTD in China through the Port of Oakland . Some of the Autolite Spark Plugs are also made in the United States in FRAM Group’s factories in Greenville, Ohio , and Albion, Illinois . Electric generator In electricity generation ,

3834-399: The requirements for larger scale power generation increased, a new limitation rose: the magnetic fields available from permanent magnets. Diverting a small amount of the power generated by the generator to an electromagnetic field coil allowed the generator to produce substantially more power. This concept was dubbed self-excitation . The field coils are connected in series or parallel with

3905-406: The satellite-Earth system is given by E mechanical = U + K {\displaystyle E_{\text{mechanical}}=U+K} E mechanical = − G M m r   + 1 2 m v 2 {\displaystyle E_{\text{mechanical}}=-G{\frac {Mm}{r}}\ +{\frac {1}{2}}\,mv^{2}} If the satellite

3976-449: The single-pole electric starter (finished between 1852 and 1854) both the stationary and the revolving parts were electromagnetic. It was also the discovery of the principle of dynamo self-excitation , which replaced permanent magnet designs. He also may have formulated the concept of the dynamo in 1861 (before Siemens and Wheatstone ) but did not patent it as he thought he was not the first to realize this. A coil of wire rotating in

4047-503: The speed of an object and is the ability of a moving object to do work on other objects when it collides with them. It is defined as one half the product of the object's mass with the square of its speed, and the total kinetic energy of a system of objects is the sum of the kinetic energies of the respective objects: K = 1 2 m v 2 {\displaystyle K={1 \over 2}mv^{2}} The principle of conservation of mechanical energy states that if

4118-521: The stator field. Wheatstone's design was similar to Siemens', with the difference that in the Siemens design the stator electromagnets were in series with the rotor, but in Wheatstone's design they were in parallel. The use of electromagnets rather than permanent magnets greatly increased the power output of a dynamo and enabled high power generation for the first time. This invention led directly to

4189-611: The sun , wind , waves and running water . Motor vehicles require electrical energy to power their instrumentation, keep the engine itself operating, and recharge their batteries. Until about the 1960s motor vehicles tended to use DC generators (dynamos) with electromechanical regulators. Following the historical trend above and for many of the same reasons, these have now been replaced by alternators with built-in rectifier circuits. Bicycles require energy to power running lights and other equipment. There are two common kinds of generator in use on bicycles: bottle dynamos which engage

4260-476: The synchronous or induction type, the primer mover speed turning the generator shaft must be at a particular speed (or narrow range of speed) to deliver power at the required utility frequency. Mechanical speed-regulating devices may waste a significant fraction of the input energy to maintain a required fixed frequency. Where it is impractical or undesired to tightly regulate the speed of the prime mover, doubly fed electric machines may be used as generators. With

4331-484: The system are so small that the principle of conservation of mechanical energy can be used as a fair approximation . Though energy cannot be created or destroyed, it can be converted to another form of energy. In a mechanical system like a swinging pendulum subjected to the conservative gravitational force where frictional forces like air drag and friction at the pivot are negligible, energy passes back and forth between kinetic and potential energy but never leaves

SECTION 60

#1732802302832

4402-411: The system. The pendulum reaches greatest kinetic energy and least potential energy when in the vertical position, because it will have the greatest speed and be nearest the Earth at this point. On the other hand, it will have its least kinetic energy and greatest potential energy at the extreme positions of its swing, because it has zero speed and is farthest from Earth at these points. However, when taking

4473-421: The turning magnetic field is provided by induction from the one they have. They also do not require speed governor equipment as they inherently operate at the connected grid frequency. An induction generator must be powered with a leading voltage; this is usually done by connection to an electrical grid, or by powering themselves with phase correcting capacitors. In the simplest form of linear electric generator,

4544-412: The work done by the non-conservative force is dependent of the path. According to the principle of conservation of mechanical energy, the mechanical energy of an isolated system remains constant in time, as long as the system is free of friction and other non-conservative forces. In any real situation, frictional forces and other non-conservative forces are present, but in many cases their effects on

4615-409: The years of 1831–1832 by Michael Faraday . The principle, later called Faraday's law , is that an electromotive force is generated in an electrical conductor which encircles a varying magnetic flux . Faraday also built the first electromagnetic generator, called the Faraday disk ; a type of homopolar generator , using a copper disc rotating between the poles of a horseshoe magnet . It produced

4686-401: Was discovered by James Prescott Joule . Many devices are used to convert mechanical energy to or from other forms of energy , e.g. an electric motor converts electrical energy to mechanical energy, an electric generator converts mechanical energy into electrical energy and a heat engine converts heat to mechanical energy. Energy is a scalar quantity and the mechanical energy of

4757-429: Was discovered, electrostatic generators were invented. They operated on electrostatic principles, by using moving electrically charged belts, plates and disks that carried charge to a high potential electrode. The charge was generated using either of two mechanisms: electrostatic induction or the triboelectric effect . Such generators generated very high voltage and low current . Because of their inefficiency and

4828-677: Was forced to sell its Autolite–related assets to the Bendix Corporation by 1973. At that point, Ford replaced the Autolite brand with the Motorcraft name worldwide for its original factory equipment, which is still in use by Ford to this day. In 1963, the portion of the Autolite company which was not acquired by Ford merged with the Mergenthaler Linotype Company , and the Eltra Corporation

4899-688: Was formed. The former Autolite portion became the Prestolite Motor and Ignition Company, later Prestolite Electric . In 1973, the Bendix Corporation had purchased both FRAM and Autolite. In 1980, the Eltra Corporation was acquired by Allied Signal Corporation which was itself acquired by Honeywell in 1999. Bendix was acquired by Allied in 1983, thereby bringing Autolite back to its original parent, Electric Autolite (Eltra) as part of Allied Signal (Honeywell). In 2011, Honeywell sold its automotive Consumer Products Group to Rank Group, which introduced FRAM Group and several other companies to take over

4970-635: Was invented in 1831 by British scientist Michael Faraday . Generators provide nearly all the power for electrical grids . In addition to electricity- and motion-based designs, photovoltaic and fuel cell powered generators use solar power and hydrogen-based fuels, respectively, to generate electrical output. The reverse conversion of electrical energy into mechanical energy is done by an electric motor , and motors and generators are very similar. Many motors can generate electricity from mechanical energy. Electromagnetic generators fall into one of two broad categories, dynamos and alternators. Mechanically,

5041-597: Was used by the firm of Elkingtons for commercial electroplating . The modern dynamo, fit for use in industrial applications, was invented independently by Sir Charles Wheatstone , Werner von Siemens and Samuel Alfred Varley . Varley took out a patent on 24 December 1866, while Siemens and Wheatstone both announced their discoveries on 17 January 1867 by delivering papers at the Royal Society . The "dynamo-electric machine" employed self-powering electromagnetic field coils rather than permanent magnets to create

#831168