Misplaced Pages

#884115

52-708: Most commonly used semiconductor materials are crystalline inorganic solids. These materials are classified according to the periodic table groups of their constituent atoms . Different semiconductor materials differ in their properties. Thus, in comparison with silicon , compound semiconductors have both advantages and disadvantages. For example, gallium arsenide (GaAs) has six times higher electron mobility than silicon, which allows faster operation; wider band gap , which allows operation of power devices at higher temperatures, and gives lower thermal noise to low power devices at room temperature; its direct band gap gives it more favorable optoelectronic properties than

104-930: A grain boundary . Like a grain boundary, a twin boundary has different crystal orientations on its two sides. But unlike a grain boundary, the orientations are not random, but related in a specific, mirror-image way. Mosaicity is a spread of crystal plane orientations. A mosaic crystal consists of smaller crystalline units that are somewhat misaligned with respect to each other. In general, solids can be held together by various types of chemical bonds , such as metallic bonds , ionic bonds , covalent bonds , van der Waals bonds , and others. None of these are necessarily crystalline or non-crystalline. However, there are some general trends as follows: Metals crystallize rapidly and are almost always polycrystalline, though there are exceptions like amorphous metal and single-crystal metals. The latter are grown synthetically, for example, fighter-jet turbines are typically made by first growing

156-515: A molten condition nor entirely in solution, but the high temperature and pressure conditions of metamorphism have acted on them by erasing their original structures and inducing recrystallization in the solid state. Other rock crystals have formed out of precipitation from fluids, commonly water, to form druses or quartz veins. Evaporites such as halite , gypsum and some limestones have been deposited from aqueous solution, mostly owing to evaporation in arid climates. Water-based ice in

208-619: A molten fluid, or by crystallization out of a solution. Some ionic compounds can be very hard, such as oxides like aluminium oxide found in many gemstones such as ruby and synthetic sapphire . Covalently bonded solids (sometimes called covalent network solids ) are typically formed from one or more non-metals, such as carbon or silicon and oxygen, and are often very hard, rigid, and brittle. These are also very common, notable examples being diamond and quartz respectively. Weak van der Waals forces also help hold together certain crystals, such as crystalline molecular solids , as well as

260-416: A "crystal" is based on the microscopic arrangement of atoms inside it, called the crystal structure . A crystal is a solid where the atoms form a periodic arrangement. ( Quasicrystals are an exception, see below ). Not all solids are crystals. For example, when liquid water starts freezing, the phase change begins with small ice crystals that grow until they fuse, forming a polycrystalline structure. In

312-611: A class of chemical compounds that contain metals and organic ligands , but lacking direct metal-carbon bonds. Metal β-diketonates, metal alkoxides , metal dialkylamides, transition metal carboxylate complexes , metal acetylacetonates , and metal phosphine complexes are representative members of this class. Some of metal-organic compounds confer solubility in organic solvents or volatility. Compounds with these properties find applications in materials science for metal organic vapor deposition (MOCVD) or sol-gel processing. Precise definitions of metal-organic compound may vary, however

364-555: A fraction of a millimetre to several centimetres across, although exceptionally large crystals are occasionally found. As of 1999 , the world's largest known naturally occurring crystal is a crystal of beryl from Malakialina, Madagascar , 18 m (59 ft) long and 3.5 m (11 ft) in diameter, and weighing 380,000 kg (840,000 lb). Some crystals have formed by magmatic and metamorphic processes, giving origin to large masses of crystalline rock . The vast majority of igneous rocks are formed from molten magma and

416-608: A perfect, exactly repeating pattern. However, in reality, most crystalline materials have a variety of crystallographic defects : places where the crystal's pattern is interrupted. The types and structures of these defects may have a profound effect on the properties of the materials. A few examples of crystallographic defects include vacancy defects (an empty space where an atom should fit), interstitial defects (an extra atom squeezed in where it does not fit), and dislocations (see figure at right). Dislocations are especially important in materials science , because they help determine

468-434: A single crystal of titanium alloy, increasing its strength and melting point over polycrystalline titanium. A small piece of metal may naturally form into a single crystal, such as Type 2 telluric iron , but larger pieces generally do not unless extremely slow cooling occurs. For example, iron meteorites are often composed of single crystal, or many large crystals that may be several meters in size, due to very slow cooling in

520-530: A single material but a class of materials. Crystalline A crystal or crystalline solid is a solid material whose constituents (such as atoms , molecules , or ions ) are arranged in a highly ordered microscopic structure, forming a crystal lattice that extends in all directions. In addition, macroscopic single crystals are usually identifiable by their geometrical shape , consisting of flat faces with specific, characteristic orientations. The scientific study of crystals and crystal formation

572-721: A single solid. Polycrystals include most metals , rocks, ceramics , and ice . A third category of solids is amorphous solids , where the atoms have no periodic structure whatsoever. Examples of amorphous solids include glass , wax , and many plastics . Despite the name, lead crystal, crystal glass , and related products are not crystals, but rather types of glass, i.e. amorphous solids. Crystals, or crystalline solids, are often used in pseudoscientific practices such as crystal therapy , and, along with gemstones , are sometimes associated with spellwork in Wiccan beliefs and related religious movements. The scientific definition of

SECTION 10

#1732772729885

624-435: A wide range of properties. Polyamorphism is a similar phenomenon where the same atoms can exist in more than one amorphous solid form. Crystallization is the process of forming a crystalline structure from a fluid or from materials dissolved in a fluid. (More rarely, crystals may be deposited directly from gas; see: epitaxy and frost .) Crystallization is a complex and extensively-studied field, because depending on

676-445: Is a noncrystalline form. Polymorphs, despite having the same atoms, may have very different properties. For example, diamond is the hardest substance known, while graphite is so soft that it is used as a lubricant. Chocolate can form six different types of crystals, but only one has the suitable hardness and melting point for candy bars and confections. Polymorphism in steel is responsible for its ability to be heat treated , giving it

728-470: Is a semiconductor compound composed of chemical elements of at least two different species. These semiconductors form for example in periodic table groups 13–15 (old groups III–V), for example of elements from the Boron group (old group III, boron , aluminium , gallium , indium ) and from group 15 (old group V, nitrogen , phosphorus , arsenic , antimony , bismuth ). The range of possible formulae

780-580: Is impossible for an ordinary periodic crystal (see crystallographic restriction theorem ). The International Union of Crystallography has redefined the term "crystal" to include both ordinary periodic crystals and quasicrystals ("any solid having an essentially discrete diffraction diagram" ). Quasicrystals, first discovered in 1982, are quite rare in practice. Only about 100 solids are known to form quasicrystals, compared to about 400,000 periodic crystals known in 2004. The 2011 Nobel Prize in Chemistry

832-483: Is its visible external shape. This is determined by the crystal structure (which restricts the possible facet orientations), the specific crystal chemistry and bonding (which may favor some facet types over others), and the conditions under which the crystal formed. By volume and weight, the largest concentrations of crystals in the Earth are part of its solid bedrock . Crystals found in rocks typically range in size from

884-589: Is known as crystallography . The process of crystal formation via mechanisms of crystal growth is called crystallization or solidification . The word crystal derives from the Ancient Greek word κρύσταλλος ( krustallos ), meaning both " ice " and " rock crystal ", from κρύος ( kruos ), "icy cold, frost". Examples of large crystals include snowflakes , diamonds , and table salt . Most inorganic solids are not crystals but polycrystals , i.e. many microscopic crystals fused together into

936-473: Is mechanically very strong, the sheets are rather loosely bound to each other. Therefore, the mechanical strength of the material is quite different depending on the direction of stress. Not all crystals have all of these properties. Conversely, these properties are not quite exclusive to crystals. They can appear in glasses or polycrystals that have been made anisotropic by working or stress —for example, stress-induced birefringence . Crystallography

988-476: Is quite broad because these elements can form binary (two elements, e.g. gallium(III) arsenide (GaAs)), ternary (three elements, e.g. indium gallium arsenide (InGaAs)) and quaternary alloys (four elements) such as aluminium gallium indium phosphide (AlInGaP)) alloy and Indium arsenide antimonide phosphide (InAsSbP). The properties of III-V compound semiconductors are similar to their group IV counterparts. The higher ionicity in these compounds, and especially in

1040-431: Is robust, cheap, and easy to process, whereas GaAs is brittle and expensive, and insulation layers cannot be created by just growing an oxide layer; GaAs is therefore used only where silicon is not sufficient. By alloying multiple compounds, some semiconductor materials are tunable, e.g., in band gap or lattice constant . The result is ternary, quaternary, or even quinary compositions. Ternary compositions allow adjusting

1092-431: Is the science of measuring the crystal structure (in other words, the atomic arrangement) of a crystal. One widely used crystallography technique is X-ray diffraction . Large numbers of known crystal structures are stored in crystallographic databases . Metalorganics (Redirected from Metalorganics ) Metal-organic compounds (jargon: metalorganics, metallo-organics) are

SECTION 20

#1732772729885

1144-424: Is the type of impurities present in a corundum crystal. In semiconductors , a special type of impurity, called a dopant , drastically changes the crystal's electrical properties. Semiconductor devices , such as transistors , are made possible largely by putting different semiconductor dopants into different places, in specific patterns. Twinning is a phenomenon somewhere between a crystallographic defect and

1196-419: Is used for LEDs. Materials transparent to the generated wavelength of light are advantageous, as this allows more efficient extraction of photons from the bulk of the material. That is, in such transparent materials, light production is not limited to just the surface. Index of refraction is also composition-dependent and influences the extraction efficiency of photons from the material. A compound semiconductor

1248-423: The indirect band gap of silicon; it can be alloyed to ternary and quaternary compositions, with adjustable band gap width, allowing light emission at chosen wavelengths, which makes possible matching to the wavelengths most efficiently transmitted through optical fibers. GaAs can be also grown in a semi-insulating form, which is suitable as a lattice-matching insulating substrate for GaAs devices. Conversely, silicon

1300-447: The mechanical strength of materials . Another common type of crystallographic defect is an impurity , meaning that the "wrong" type of atom is present in a crystal. For example, a perfect crystal of diamond would only contain carbon atoms, but a real crystal might perhaps contain a few boron atoms as well. These boron impurities change the diamond's color to slightly blue. Likewise, the only difference between ruby and sapphire

1352-737: The II-VI compound, tends to increase the fundamental bandgap with respect to the less ionic compounds. Metalorganic vapor-phase epitaxy (MOVPE) is the most popular deposition technology for the formation of compound semiconducting thin films for devices. It uses ultrapure metalorganics and/or hydrides as precursor source materials in an ambient gas such as hydrogen . Other techniques of choice include: High carrier mobilities and high electric breakdown field at room temperature as excellent electronics characteristics. Extremely high nanomechanical resonator quality factor. The following semiconducting systems can be tuned to some extent, and represent not

1404-429: The air ( ice fog ) more often grow from a supersaturated gaseous-solution of water vapor and air, when the temperature of the air drops below its dew point , without passing through a liquid state. Another unusual property of water is that it expands rather than contracts when it crystallizes. Many living organisms are able to produce crystals grown from an aqueous solution , for example calcite and aragonite in

1456-413: The band gap within the range of the involved binary compounds; however, in case of combination of direct and indirect band gap materials there is a ratio where indirect band gap prevails, limiting the range usable for optoelectronics; e.g. AlGaAs LEDs are limited to 660 nm by this. Lattice constants of the compounds also tend to be different, and the lattice mismatch against the substrate, dependent on

1508-510: The case of most molluscs or hydroxylapatite in the case of bones and teeth in vertebrates . The same group of atoms can often solidify in many different ways. Polymorphism is the ability of a solid to exist in more than one crystal form. For example, water ice is ordinarily found in the hexagonal form Ice I h , but can also exist as the cubic Ice I c , the rhombohedral ice II , and many other forms. The different polymorphs are usually called different phases . In addition,

1560-404: The conditions, a single fluid can solidify into many different possible forms. It can form a single crystal , perhaps with various possible phases , stoichiometries , impurities, defects , and habits . Or, it can form a polycrystal , with various possibilities for the size, arrangement, orientation, and phase of its grains. The final form of the solid is determined by the conditions under which

1612-409: The crystal can shrink or stretch it. Another is birefringence , where a double image appears when looking through a crystal. Moreover, various properties of a crystal, including electrical conductivity , electrical permittivity , and Young's modulus , may be different in different directions in a crystal. For example, graphite crystals consist of a stack of sheets, and although each individual sheet

List of semiconductor materials - Misplaced Pages Continue

1664-411: The crystal is one grain in a polycrystalline solid. The flat faces (also called facets ) of a euhedral crystal are oriented in a specific way relative to the underlying atomic arrangement of the crystal : they are planes of relatively low Miller index . This occurs because some surface orientations are more stable than others (lower surface energy ). As a crystal grows, new atoms attach easily to

1716-532: The crystals may form hexagons, such as ordinary water ice ). Crystals are commonly recognized, macroscopically, by their shape, consisting of flat faces with sharp angles. These shape characteristics are not necessary for a crystal—a crystal is scientifically defined by its microscopic atomic arrangement, not its macroscopic shape—but the characteristic macroscopic shape is often present and easy to see. Euhedral crystals are those that have obvious, well-formed flat faces. Anhedral crystals do not, usually because

1768-606: The degree of crystallization depends primarily on the conditions under which they solidified. Such rocks as granite , which have cooled very slowly and under great pressures, have completely crystallized; but many kinds of lava were poured out at the surface and cooled very rapidly, and in this latter group a small amount of amorphous or glassy matter is common. Other crystalline rocks, the metamorphic rocks such as marbles , mica-schists and quartzites , are recrystallized. This means that they were at first fragmental rocks like limestone , shale and sandstone and have never been in

1820-453: The eight faces of the octahedron belong to another crystallographic form reflecting a different symmetry of the isometric system. A crystallographic form is described by placing the Miller indices of one of its faces within brackets. For example, the octahedral form is written as {111}, and the other faces in the form are implied by the symmetry of the crystal. Forms may be closed, meaning that

1872-710: The final block of ice, each of the small crystals (called " crystallites " or "grains") is a true crystal with a periodic arrangement of atoms, but the whole polycrystal does not have a periodic arrangement of atoms, because the periodic pattern is broken at the grain boundaries . Most macroscopic inorganic solids are polycrystalline, including almost all metals , ceramics , ice , rocks , etc. Solids that are neither crystalline nor polycrystalline, such as glass , are called amorphous solids , also called glassy , vitreous, or noncrystalline. These have no periodic order, even microscopically. There are distinct differences between crystalline solids and amorphous solids: most notably,

1924-531: The fluid is being solidified, such as the chemistry of the fluid, the ambient pressure , the temperature , and the speed with which all these parameters are changing. Specific industrial techniques to produce large single crystals (called boules ) include the Czochralski process and the Bridgman technique . Other less exotic methods of crystallization may be used, depending on the physical properties of

1976-415: The form can completely enclose a volume of space, or open, meaning that it cannot. The cubic and octahedral forms are examples of closed forms. All the forms of the isometric system are closed, while all the forms of the monoclinic and triclinic crystal systems are open. A crystal's faces may all belong to the same closed form, or they may be a combination of multiple open or closed forms. A crystal's habit

2028-402: The form of snow , sea ice , and glaciers are common crystalline/polycrystalline structures on Earth and other planets. A single snowflake is a single crystal or a collection of crystals, while an ice cube is a polycrystal . Ice crystals may form from cooling liquid water below its freezing point, such as ice cubes or a frozen lake. Frost , snowflakes, or small ice crystals suspended in

2080-458: The interlayer bonding in graphite . Substances such as fats , lipids and wax form molecular bonds because the large molecules do not pack as tightly as atomic bonds. This leads to crystals that are much softer and more easily pulled apart or broken. Common examples include chocolates, candles, or viruses. Water ice and dry ice are examples of other materials with molecular bonding. Polymer materials generally will form crystalline regions, but

2132-471: The lengths of the molecules usually prevent complete crystallization—and sometimes polymers are completely amorphous. A quasicrystal consists of arrays of atoms that are ordered but not strictly periodic. They have many attributes in common with ordinary crystals, such as displaying a discrete pattern in x-ray diffraction , and the ability to form shapes with smooth, flat faces. Quasicrystals are most famous for their ability to show five-fold symmetry, which

List of semiconductor materials - Misplaced Pages Continue

2184-407: The mixing ratio, causes defects in amounts dependent on the mismatch magnitude; this influences the ratio of achievable radiative/nonradiative recombinations and determines the luminous efficiency of the device. Quaternary and higher compositions allow adjusting simultaneously the band gap and the lattice constant, allowing increasing radiant efficiency at wider range of wavelengths; for example AlGaInP

2236-413: The process of forming a glass does not release the latent heat of fusion , but forming a crystal does. A crystal structure (an arrangement of atoms in a crystal) is characterized by its unit cell , a small imaginary box containing one or more atoms in a specific spatial arrangement. The unit cells are stacked in three-dimensional space to form the crystal. The symmetry of a crystal is constrained by

2288-432: The requirement that the unit cells stack perfectly with no gaps. There are 219 possible crystal symmetries (230 is commonly cited, but this treats chiral equivalents as separate entities), called crystallographic space groups . These are grouped into 7 crystal systems , such as cubic crystal system (where the crystals may form cubes or rectangular boxes, such as halite shown at right) or hexagonal crystal system (where

2340-423: The rougher and less stable parts of the surface, but less easily to the flat, stable surfaces. Therefore, the flat surfaces tend to grow larger and smoother, until the whole crystal surface consists of these plane surfaces. (See diagram on right.) One of the oldest techniques in the science of crystallography consists of measuring the three-dimensional orientations of the faces of a crystal, and using them to infer

2392-444: The same atoms may be able to form noncrystalline phases . For example, water can also form amorphous ice , while SiO 2 can form both fused silica (an amorphous glass) and quartz (a crystal). Likewise, if a substance can form crystals, it can also form polycrystals. For pure chemical elements, polymorphism is known as allotropy . For example, diamond and graphite are two crystalline forms of carbon , while amorphous carbon

2444-469: The same name This set index article lists chemical compounds articles associated with the same name. If an internal link led you here, you may wish to change the link to point directly to the intended article. Retrieved from " https://en.wikipedia.org/w/index.php?title=Metal-organic_compound&oldid=1192261222 " Category : Set index articles on chemistry Hidden categories: Articles with short description Short description

2496-744: The substance, including hydrothermal synthesis , sublimation , or simply solvent-based crystallization . Large single crystals can be created by geological processes. For example, selenite crystals in excess of 10  m are found in the Cave of the Crystals in Naica, Mexico. For more details on geological crystal formation, see above . Crystals can also be formed by biological processes, see above . Conversely, some organisms have special techniques to prevent crystallization from occurring, such as antifreeze proteins . An ideal crystal has every atom in

2548-556: The term may describe: Organometallic chemistry Metal coordination complexes of organic ligands. References [ edit ] ^ Fulton, J. Robin; Holland, Andrew W.; Fox, Daniel J.; Bergman, Robert G. (January 2002). "Formation, Reactivity, and Properties of Nondative Late Transition Metal–Oxygen and–Nitrogen Bonds" . Accounts of Chemical Research . 35 (1): 44–56. doi : 10.1021/ar000132x . ISSN   0001-4842 . PMC   1473979 . PMID   11790088 . [REDACTED] Index of chemical compounds with

2600-429: The underlying crystal symmetry . A crystal's crystallographic forms are sets of possible faces of the crystal that are related by one of the symmetries of the crystal. For example, crystals of galena often take the shape of cubes, and the six faces of the cube belong to a crystallographic form that displays one of the symmetries of the isometric crystal system . Galena also sometimes crystallizes as octahedrons, and

2652-620: The vacuum of space. The slow cooling may allow the precipitation of a separate phase within the crystal lattice, which form at specific angles determined by the lattice, called Widmanstatten patterns . Ionic compounds typically form when a metal reacts with a non-metal, such as sodium with chlorine. These often form substances called salts, such as sodium chloride (table salt) or potassium nitrate ( saltpeter ), with crystals that are often brittle and cleave relatively easily. Ionic materials are usually crystalline or polycrystalline. In practice, large salt crystals can be created by solidification of

SECTION 50

#1732772729885

2704-400: Was awarded to Dan Shechtman for the discovery of quasicrystals. Crystals can have certain special electrical, optical, and mechanical properties that glass and polycrystals normally cannot. These properties are related to the anisotropy of the crystal, i.e. the lack of rotational symmetry in its atomic arrangement. One such property is the piezoelectric effect , where a voltage across

#884115