Misplaced Pages

#56943

134-559: In powered flight , the pilot makes frequent use of the VSI to ascertain that level flight is being maintained, especially during turning maneuvers. In gliding , the instrument is used almost continuously during normal flight, often with an audible output, to inform the pilot of rising or sinking air . It is usual for gliders to be equipped with more than one type of variometer. The simpler type does not need an external source of power and can therefore be relied upon to function regardless of whether

268-443: A gas turbine engine offered. Thus was born the idea to mate a turbine engine to a traditional propeller. Because gas turbines optimally spin at high speed, a turboprop features a gearbox to lower the speed of the shaft so that the propeller tips don't reach supersonic speeds. Often the turbines that drive the propeller are separate from the rest of the rotating components so that they can rotate at their own best speed (referred to as

402-413: A turn and slip indicator are used when there is zero visibility. Increasingly, anti-collision warning systems such as FLARM are also used and are even mandatory in some European countries. An Emergency Position-Indicating Radio Beacon ( ELT ) may also be fitted into the glider to reduce search and rescue time in case of an accident. Much more than in other types of aviation, glider pilots depend on

536-423: A variometer and an airband radio ( transceiver ), each of which may be required in some countries. A transponder may be installed to assist controllers when the glider is crossing busy or controlled airspace. This may be supplemented by ADS-B . Without these devices access to some airspace may become increasingly restricted in some countries. In countries where cloud-flying is allowed, an artificial horizon or

670-458: A battery or power source has been fitted. The electronic type with audio needs a power source to be operative during the flight. The instrument is of little interest during launching and landing, with the exception of aerotow , where the pilot will usually want to avoid releasing in sink. In 1930, according to Ann Welch , " Kronfeld ...was one of the first to use a variometer, a device suggested by Alexander Lippisch ." Welch goes on to state that

804-618: A better efficiency. A hybrid system as emergency back-up and for added power in take-off is offered for sale by Axter Aerospace, Madrid, Spain. Small multicopter UAVs are almost always powered by electric motors. Reaction engines generate the thrust to propel an aircraft by ejecting the exhaust gases at high velocity from the engine, the resultant reaction of forces driving the aircraft forwards. The most common reaction propulsion engines flown are turbojets, turbofans and rockets. Other types such as pulsejets , ramjets , scramjets and pulse detonation engines have also flown. In jet engines

938-419: A combustion section where fuel is added and ignited, one or more turbines that extract power from the expanding exhaust gases to drive the compressor, and an exhaust nozzle that accelerates the exhaust gases out the back of the engine to create thrust. When turbojets were introduced, the top speed of fighter aircraft equipped with them was at least 100 miles per hour faster than competing piston-driven aircraft. In

1072-564: A common crankshaft. The vast majority of V engines are water-cooled. The V design provides a higher power-to-weight ratio than an inline engine, while still providing a small frontal area. Perhaps the most famous example of this design is the legendary Rolls-Royce Merlin engine, a 27-litre (1649 in ) 60° V12 engine used in, among others, the Spitfires that played a major role in the Battle of Britain . A horizontally opposed engine, also called

1206-490: A cooling system into the air duct of a hydrogen jet engine permits greater fuel injection at high speed and obviates the need for the duct to be made of refractory or actively cooled materials. This greatly improves the thrust/weight ratio of the engine at high speed. It is thought that this design of engine could permit sufficient performance for antipodal flight at Mach 5, or even permit a single stage to orbit vehicle to be practical. The hybrid air-breathing SABRE rocket engine

1340-440: A cylinder on the other side. Opposed, air-cooled four- and six-cylinder piston engines are by far the most common engines used in small general aviation aircraft requiring up to 400 horsepower (300 kW) per engine. Aircraft that require more than 400 horsepower (300 kW) per engine tend to be powered by turbine engines . An H configuration engine is essentially a pair of horizontally opposed engines placed together, with

1474-501: A day if the weather is suitable. Early gliders had no cockpit and the pilot sat on a small seat located just ahead of the wing. These were known as " primary gliders " and they were usually launched from the tops of hills, though they are also capable of short hops across the ground while being towed behind a vehicle. To enable gliders to soar more effectively than primary gliders, the designs minimized drag. Gliders now have very smooth, narrow fuselages and very long, narrow wings with

SECTION 10

#1732790367057

1608-462: A diaphragm, a vane (horn), a taut band, or are electric based. The vane variometer consists of a rotating vane, centered by a coil spring, dividing a chamber into two parts, one connected to a static port, and the other to an expansion chamber. Electric variometers use thermistors sensitive to airflow, or circuit boards consisting of variable resistors connected to the membrane of a tiny vacuum cavity. A simple variometer can be constructed by adding

1742-408: A flat or boxer engine, has two banks of cylinders on opposite sides of a centrally located crankcase. The engine is either air-cooled or liquid-cooled, but air-cooled versions predominate. Opposed engines are mounted with the crankshaft horizontal in airplanes , but may be mounted with the crankshaft vertical in helicopters . Due to the cylinder layout, reciprocating forces tend to cancel, resulting in

1876-406: A flight and even, in some cases, for take-off . Some high-performance motor gliders (known as "self-sustaining" gliders) may have an engine-driven retractable propeller which can be used to sustain flight. Other motor gliders have enough thrust to launch themselves before the engine is retracted and are known as "self-launching" gliders. Another type is the self-launching "touring motor glider", where

2010-572: A fraction of the cost of traditional engines. Such conversions first took place in the early 1970s; and as of 10 December 2006 the National Transportation Safety Board has only seven reports of incidents involving aircraft with Mazda engines, and none of these is of a failure due to design or manufacturing flaws. The most common combustion cycle for aero engines is the four-stroke with spark ignition. Two-stroke spark ignition has also been used for small engines, while

2144-407: A free-turbine engine). A turboprop is very efficient when operated within the realm of cruise speeds it was designed for, which is typically 200 to 400 mph (320 to 640 km/h). Turboshaft engines are used primarily for helicopters and auxiliary power units . A turboshaft engine is similar to a turboprop in principle, but in a turboprop the propeller is supported by the engine and the engine

2278-418: A glider's contest ID when flying in close proximity to one another to alert them of potential dangers. For example, during gatherings of multiple gliders within thermals (known as "gaggles"), one pilot might report "Six-Seven-Romeo I am right below you". Fibreglass gliders are invariably painted white to minimise their skin temperature in sunlight. Fibreglass resin loses strength as its temperature rises into

2412-456: A handful of types are still in production. The last airliner that used turbojets was the Concorde , whose Mach 2 airspeed permitted the engine to be highly efficient. A turbofan engine is much the same as a turbojet, but with an enlarged fan at the front that provides thrust in much the same way as a ducted propeller , resulting in improved fuel efficiency . Though the fan creates thrust like

2546-423: A height of 300 metres (1,000 ft). Glide slope control devices are then used to adjust the height to assure landing at the desired point. The ideal landing pattern positions the glider on final approach so that a deployment of 30–60% of the spoilers/dive brakes/flaps brings it to the desired touchdown point. In this way the pilot has the option of opening or closing the spoilers/air-brakes to extend or steepen

2680-433: A high aspect ratio and winglets . The early gliders were made mainly of wood with metal fastenings, stays and control cables. Later fuselages made of fabric-covered steel tube were married to wood and fabric wings for lightness and strength. New materials such as carbon-fiber , fiber glass and Kevlar have since been used with computer-aided design to increase performance. The first glider to use glass-fiber extensively

2814-705: A higher speed at any given glide angle. This is an advantage in strong conditions when the gliders spend only a small amount of time climbing in thermals. The pilot can jettison the water ballast before it becomes a disadvantage in weaker thermal conditions. Another use of water ballast is to dampen air turbulence such as might be encountered during ridge soaring . To avoid undue stress on the airframe, gliders must jettison any water ballast before landing. Most gliders are built in Europe and are designed to EASA Certification Specification CS-22 (previously Joint Aviation Requirements -22). These define minimum standards for safety in

SECTION 20

#1732790367057

2948-460: A hillside, or to the ground. Except when hill-soaring (exploiting the lift close to the up-wind side of a hill), these are generally very unprofitable positions for glider pilots to be in. The most useful forms of lift ( thermal and wave lift) are found at higher altitudes and it is very hard for a pilot to detect or exploit them without the use of a variometer. After the variometer was invented in 1929 by Alexander Lippisch and Robert Kronfeld ,

3082-728: A large degree due to post-World War I regulations forbidding the construction and flight of motorised planes in Germany, so the country's aircraft enthusiasts often turned to gliders and were actively encouraged by the German government, particularly at flying sites suited to gliding flight like the Wasserkuppe . The sporting use of gliders rapidly evolved in the 1930s and is now their main application. As their performance improved, gliders began to be used for cross-country flying and now regularly fly hundreds or even thousands of kilometres in

3216-407: A large reservoir (a vacuum flask ) to augment the storage capacity of a common aircraft rate-of-climb instrument. In its simplest electronic form, the instrument consists of an air bottle connected to the external atmosphere through a sensitive air flow meter. As the aircraft changes altitude, the atmospheric pressure outside the aircraft changes and air flows into or out of the air bottle to equalise

3350-442: A manual switch instead of the g sensor. In 1954, MacCready pointed out the advantages of an Audio Variometer, "There is much to be gained if the variometer indication is presented to the pilot by sound. More than any other instrument except during blind flying, the variometer must be watched continuously. if the pilot can get the reading by ear, he can improve his thermal flying by watching nearby gliders, and he can materially improve

3484-414: A membrane compensator, compensation by venturi , or are electronically compensated. The membrane compensator is an elastic membrane, which flexes according to the total pressure (pitot plus static) from airspeed. Thus, airspeed effects cancel out an increase in sink, due to acceleration, or a decrease in sink, due to deceleration. The venturi compensator supplies a speed-dependent negative pressure, so that

3618-508: A minimum loss of height in between. Sailplanes have rigid wings and either skids or undercarriage . In contrast hang gliders and paragliders use the pilot's feet for the start of the launch and for the landing. These latter types are described in separate articles, though their differences from sailplanes are covered below. Sailplanes are usually launched by winch or aerotow, though other methods, auto tow and bungee, are occasionally used. These days almost all gliders are sailplanes, but in

3752-569: A peak pressure of 30 MPa (300 bar). Although engine weight increases by 30%, aircraft fuel consumption is reduced by 15%. Sponsored by the European Commission under Framework 7 project LEMCOTEC , Bauhaus Luftfahrt, MTU Aero Engines and GKN Aerospace presented the concept in 2015, raising the overall engine pressure ratio to over 100 for a 15.2% fuel burn reduction compared to 2025 engines. On multi-engine aircraft, engine positions are numbered from left to right from

3886-478: A piston-engine with two 10 piston banks without a high-pressure turbine, increasing efficiency with non-stationary isochoric - isobaric combustion for higher peak pressures and temperatures. The 11,200 lb (49.7 kN) engine could power a 50-seat regional jet . Its cruise TSFC would be 11.5 g/kN/s (0.406 lb/lbf/hr) for an overall engine efficiency of 48.2%, for a burner temperature of 1,700 K (1,430 °C), an overall pressure ratio of 38 and

4020-424: A propeller, the surrounding duct frees it from many of the restrictions that limit propeller performance. This operation is a more efficient way to provide thrust than simply using the jet nozzle alone, and turbofans are more efficient than propellers in the transsonic range of aircraft speeds and can operate in the supersonic realm. A turbofan typically has extra turbine stages to turn the fan. Turbofans were among

4154-425: A search for replacement fuels for general aviation aircraft a priority for pilots’ organizations. Turbine engines and aircraft diesel engines burn various grades of jet fuel . Jet fuel is a relatively less volatile petroleum derivative based on kerosene , but certified to strict aviation standards, with additional additives. Model aircraft typically use nitro engines (also known as "glow engines" due to

Variometer - Misplaced Pages Continue

4288-445: A separate control. Although there is only a single main wheel, the glider's wing can be kept level by using the flight controls until it is almost stationary. Pilots usually land back at the airfield from which they took off, but a landing is possible in any flat field about 250 metres long. Ideally, should circumstances permit, a glider would fly a standard pattern , or circuit , in preparation for landing, typically starting at

4422-463: A single row of cylinders, as used in automotive language, but in aviation terms, the phrase "inline engine" also covers V-type and opposed engines (as described below), and is not limited to engines with a single row of cylinders. This is typically to differentiate them from radial engines . A straight engine typically has an even number of cylinders, but there are instances of three- and five-cylinder engines. The greatest advantage of an inline engine

4556-404: A smooth running engine. Opposed-type engines have high power-to-weight ratios because they have a comparatively small, lightweight crankcase. In addition, the compact cylinder arrangement reduces the engine's frontal area and allows a streamlined installation that minimizes aerodynamic drag. These engines always have an even number of cylinders, since a cylinder on one side of the crankcase "opposes"

4690-428: A time in this way, and thus by constant practice so increase their knowledge and skill that they can rise into the higher air and search out the currents which enable the soaring birds to transport themselves to any desired point, by first rising in a circle, and then sailing off at a descending angle." According to Paul MacCready , "A variometer is essentially a pressure altimeter with a leak which tends to make it read

4824-416: A variety of methods. Probably the nicest is to utilize the total energy venturi and the dynamic pressure from the pitot tube." As Reichmann explained, a "Netto variometer shows the climb and sink of airmass (not of the sailplane!)...In order to achieve a 'net' indication, the always present polar sink of the sailplane must be 'compensated out' of the indication. To do this, one makes use of the fact that above

4958-456: A wide range of characteristics such as controllability and strength. For example, gliders must have design features to minimize the possibility of incorrect assembly (gliders are often stowed in disassembled configuration, with at least the wings being detached). Automatic connection of the controls during rigging is the common method of achieving this. The two most common methods of launching sailplanes are by aerotow and by winch. When aerotowed,

5092-533: Is a pre-cooled engine under development. At the April 2018 ILA Berlin Air Show , Munich -based research institute de:Bauhaus Luftfahrt presented a high-efficiency composite cycle engine for 2050, combining a geared turbofan with a piston engine core. The 2.87 m diameter, 16-blade fan gives a 33.7 ultra-high bypass ratio , driven by a geared low-pressure turbine but the high-pressure compressor drive comes from

5226-449: Is a twin-spool engine, allowing only two different speeds for the turbines. Pulsejets are mechanically simple devices that—in a repeating cycle—draw air through a no-return valve at the front of the engine into a combustion chamber and ignite it. The combustion forces the exhaust gases out the back of the engine. It produces power as a series of pulses rather than as a steady output, hence the name. The only application of this type of engine

5360-490: Is above and behind. In the Cessna 337 Skymaster , a push-pull twin-engine airplane, engine No. 1 is the one at the front of the fuselage, while engine No. 2 is aft of the cabin. Aircraft reciprocating (piston) engines are typically designed to run on aviation gasoline . Avgas has a higher octane rating than automotive gasoline to allow higher compression ratios , power output, and efficiency at higher altitudes. Currently

5494-453: Is bolted to the airframe : in a turboshaft, the engine does not provide any direct physical support to the helicopter's rotors. The rotor is connected to a transmission which is bolted to the airframe, and the turboshaft engine drives the transmission. The distinction is seen by some as slim, as in some cases aircraft companies make both turboprop and turboshaft engines based on the same design. A number of electrically powered aircraft, such as

Variometer - Misplaced Pages Continue

5628-406: Is converted to an effective altitude change by dividing by the acceleration of gravity, and the mass of the aircraft, so: Δ E tot m g = Δ h + Δ V 2 2 g {\displaystyle {\Delta E_{\text{tot}} \over mg}=\Delta h+{{\Delta V}^{2} \over 2g}} Total-Energy Variometers use

5762-472: Is how it should be understood. Without further information it remains unclear what changes are being measured. The simple variometers...are rate of climb indicators. Since the actual sailplane climb and sink displayed on these instruments depends not only on airmass movement and sailplane performance, but also in large part on angle-of-attack changes ( elevator movements )...This makes it virtually impossible to extract useful information, such as - for instance -

5896-400: Is installed in a powered aircraft. The term "variometer" is most often used when the instrument is installed in a glider or sailplane. An "Inertial-lead" or "Instantaneous" VSI (IVSI) uses accelerometers to provide a quicker response to changes in vertical speed. Human beings, unlike birds and other flying animals, are not able directly to sense climb and sink rates. Before the invention of

6030-417: Is known as "soaring". By finding lift sufficiently often, experienced pilots fly cross-country , often on pre-declared tasks of hundreds of kilometers, usually back to the original launch site. Cross-country flying and aerobatics are the two forms of competitive gliding . For information about the forces in gliding flight, see lift-to-drag ratio . Pilots need some form of control over the glide slope to land

6164-720: Is more common because it is difficult to get enough air-flow to cool the rear cylinders directly. Inline engines were common in early aircraft; one was used in the Wright Flyer , the aircraft that made the first controlled powered flight. However, the inherent disadvantages of the design soon became apparent, and the inline design was abandoned, becoming a rarity in modern aviation. For other configurations of aviation inline engine, such as X-engines , U-engines , H-engines , etc., see Inline engine (aeronautics) . Cylinders in this engine are arranged in two in-line banks, typically tilted 60–90 degrees apart from each other and driving

6298-421: Is no bottle to be affected by changes in temperature and fewer chances for leaks to occur in the connecting tubes. The designs described above, which measure the rate of change of altitude by automatically detecting the change in static pressure as the aircraft changes altitude are referred to as "uncompensated" variometers. The term "vertical speed indicator" or "VSI" is most often used for the instrument when it

6432-430: Is of lesser concern, rocket engines can be useful because they produce very large amounts of thrust and weigh very little. A rocket turbine engine is a combination of two types of propulsion engines: a liquid-propellant rocket and a turbine jet engine. Its power-to-weight ratio is a little higher than a regular jet engine, and works at higher altitudes. For very high supersonic/low hypersonic flight speeds, inserting

6566-750: Is proportional to height E pot = m g h {\displaystyle E_{\text{pot}}=mgh} where m {\displaystyle m} is the glider mass and g {\displaystyle g} the acceleration of gravity and 4. Kinetic energy is proportional to velocity squared, E kin = 1 2 m V 2 {\displaystyle E_{\text{kin}}={1 \over 2}mV^{2}} then from 2: 5. Δ E tot = m g Δ h + 1 2 m Δ V 2 {\displaystyle \Delta E_{\text{tot}}=mg\Delta h+{1 \over 2}m{\Delta V}^{2}} 6. Typically, this

6700-448: Is showing a climb, the tone is often chopped and the rate of chopping may be increased as the climb rate increases, while during a descent the tone is not chopped. The vario is typically silent in still air or in lift which is weaker than the typical sink rate of the glider at minimum sink . This audio signal allows the pilot to concentrate on the external view instead of having to watch the instruments, thus improving safety and also giving

6834-477: Is simply one that tells you the net vertical air movement with the sailplane movement or sink taken out of the usual variometer reading." The Relative Netto Variometer indicates the vertical speed the glider would achieve IF it flies at thermalling speed - independent of current air speed and attitude. This reading is calculated as the Netto reading minus the glider's minimum sink. When the glider circles to thermal,

SECTION 50

#1732790367057

6968-471: Is sometimes confusion about gliders/sailplanes, hang gliders and paragliders. In particular, paragliders and hang gliders are both foot-launched. The main differences between the types are: Eight competition classes of glider have been defined by the FAI . They are: A large proportion of gliders have been and are still made in Germany, the birthplace of the sport. In Germany there are several manufacturers but

7102-445: Is sufficient wind blowing up the hill. Bungee launching was the predominant method of launching early gliders. Some modern gliders can self-launch by using retractable engines or just retractable propellers. (see motor glider ). These engines can use internal combustion or battery power. Once launched, gliders try to gain height using thermals , ridge lift , lee waves or convergence zones and can remain airborne for hours. This

7236-513: Is that it allows the aircraft to be designed with a low frontal area to minimize drag. If the engine crankshaft is located above the cylinders, it is called an inverted inline engine: this allows the propeller to be mounted high up to increase ground clearance, enabling shorter landing gear. The disadvantages of an inline engine include a poor power-to-weight ratio , because the crankcase and crankshaft are long and thus heavy. An in-line engine may be either air-cooled or liquid-cooled, but liquid-cooling

7370-471: Is the Netto or airmass variometer. In addition to TE compensation, the Netto variometer adjusts for the intrinsic sink rate of the glider at a given speed (the polar curve ) adjusted for the wing loading due to water ballast. The Netto variometer will always read zero in still air. This provides the pilot with the accurate measurement of air mass vertical movement critical for final glides (the last glide to

7504-614: Is the power component of an aircraft propulsion system . Aircraft using power components are referred to as powered flight . Most aircraft engines are either piston engines or gas turbines , although a few have been rocket powered and in recent years many small UAVs have used electric motors . In commercial aviation the major Western manufacturers of turbofan engines are Pratt & Whitney (a subsidiary of Raytheon Technologies ), General Electric , Rolls-Royce , and CFM International (a joint venture of Safran Aircraft Engines and General Electric). Russian manufacturers include

7638-400: Is the total change in energy experienced by the glider, including both altitude and speed. An uncompensated variometer will simply indicate vertical speed of the glider, giving rise to the possibility of a " stick thermal ," i.e., a change in altitude caused by stick input only. If a pilot pulls back on the stick, the glider will rise, but also slow down as well. But if a glider is rising without

7772-447: The variometer article for more information). Variometers are sometimes fitted with mechanical or electronic devices to indicate the optimal speed to fly for given conditions. The MacCready setting can be input electronically or adjusted using a ring surrounding the dial. These devices are based on the mathematical theory attributed to Paul MacCready though it was first described by Wolfgang Späte in 1938. MacCready theory solves

7906-527: The QinetiQ Zephyr , have been designed since the 1960s. Some are used as military drones . In France in late 2007, a conventional light aircraft powered by an 18 kW electric motor using lithium polymer batteries was flown, covering more than 50 kilometers (31 mi), the first electric airplane to receive a certificate of airworthiness . On 18 May 2020, the Pipistrel E-811 was

8040-684: The Rutan Quickie . The single-rotor engine was put into a Chevvron motor glider and into the Schleicher ASH motor-gliders. After the demise of MidWest, all rights were sold to Diamond of Austria, who have since developed a MkII version of the engine. As a cost-effective alternative to certified aircraft engines some Wankel engines, removed from automobiles and converted to aviation use, have been fitted in homebuilt experimental aircraft . Mazda units with outputs ranging from 100 horsepower (75 kW) to 300 horsepower (220 kW) can be

8174-508: The Space Shuttle with a glide ratio of 4.5:1. High aerodynamic efficiency is essential to achieve a good gliding performance, and so gliders often have aerodynamic features seldom found in other aircraft. The wings of a modern racing glider are designed by computers to create a low-drag laminar flow airfoil . After the wings' surfaces have been shaped by a mould to great accuracy, they are then highly polished. Vertical winglets at

SECTION 60

#1732790367057

8308-484: The United Engine Corporation , Aviadvigatel and Klimov . Aeroengine Corporation of China was formed in 2016 with the merger of several smaller companies. The largest manufacturer of turboprop engines for general aviation is Pratt & Whitney. General Electric announced in 2015 entrance into the market. In this section, for clarity, the term "inline engine" refers only to engines with

8442-424: The gyroscopic effects of the heavy rotating engine produced handling problems in aircraft and the engines also consumed large amounts of oil since they used total loss lubrication, the oil being mixed with the fuel and ejected with the exhaust gases. Castor oil was used for lubrication, since it is not soluble in petrol, and the resultant fumes were nauseating to the pilots. Engine designers had always been aware of

8576-424: The oxygen necessary for fuel combustion comes from the air, while rockets carry an oxidizer (usually oxygen in some form) as part of the fuel load, permitting their use in space. A turbojet is a type of gas turbine engine that was originally developed for military fighters during World War II . A turbojet is the simplest of all aircraft gas turbines. It consists of a compressor to draw air in and compress it,

8710-440: The variometer , which is a very sensitive vertical speed indicator , to measure the climb or sink rate of the plane. This enables the pilot to detect minute changes caused when the glider enters rising or sinking air masses. Most often electronic 'varios' are fitted to a glider, though mechanical varios are often installed as back-up. The electronic variometers produce a modulated sound of varying amplitude and frequency depending on

8844-413: The "first real thermal soaring" occurred in 1930 by A. Haller and Wolf Hirth , with Hirth using a variometer in his Musterle . Frank Irving states that Arthur Kantrowitz first mentioned total energy in 1940. However, as early as 1901, Wilbur Wright wrote about thermals, "when gliding operators have attained greater skill, they can, with comparative safety, maintain themselves in the air for hours at

8978-764: The Clerget 14F Diesel radial engine (1939) has the same power to weight ratio as a gasoline radial. Improvements in Diesel technology in automobiles (leading to much better power-weight ratios), the Diesel's much better fuel efficiency and the high relative taxation of AVGAS compared to Jet A1 in Europe have all seen a revival of interest in the use of diesels for aircraft. Thielert Aircraft Engines converted Mercedes Diesel automotive engines, certified them for aircraft use, and became an OEM provider to Diamond Aviation for their light twin. Financial problems have plagued Thielert, so Diamond's affiliate — Austro Engine — developed

9112-513: The English-speaking world, the word 'glider' is more common. Gliders benefit from producing very low drag for any given amount of lift, and this is best achieved with long, thin wings , a slender fuselage and smooth surfaces with an absence of protuberances. Aircraft with these features are able to soar – climb efficiently in rising air produced by thermals or hills. In still air, sailplanes can glide long distances at high speed with

9246-609: The Nicks Venturi, and the Double-Slotted Tube, developed by Bardowicks of Akaflieg Hannover, also known as the Braunschweig Tube. Very few powered aircraft have total energy variometers. Pilots of powered aircraft are more interested in the true rate of change of altitude, as they often want to hold a constant altitude or maintain a steady climb or descent. A second type of compensated variometer

9380-574: The Wankel engine has been used in motor gliders where the compactness, light weight, and smoothness are crucially important. The now-defunct Staverton-based firm MidWest designed and produced single- and twin-rotor aero engines, the MidWest AE series . These engines were developed from the motor in the Norton Classic motorcycle . The twin-rotor version was fitted into ARV Super2s and

9514-669: The aircraft is: 1. E tot = E pot + E kin {\displaystyle E_{\text{tot}}=E_{\text{pot}}+E_{\text{kin}}} where E pot {\displaystyle E_{\text{pot}}} is the potential energy, and E kin {\displaystyle E_{\text{kin}}} is the kinetic energy. So the change in total energy is: 2. Δ E tot = Δ E pot + Δ E kin {\displaystyle \Delta E_{\text{tot}}=\Delta E_{\text{pot}}+\Delta E_{\text{kin}}} Since 3. Potential energy

9648-466: The altitude of a moment earlier. It consists of a container vented to the outside air in such a way that the pressure inside the flask lags slightly behind the outside static pressure. The rate of climb measurement comes from the rate-of-air inflow or outflow from the container." Variometers measure the rate of change of altitude by detecting the change in air pressure (static pressure) as altitude changes. Common types of variometers include those based on

9782-429: The altitude of the aircraft is increasing. Air flowing into the bottle indicates that the aircraft is descending. Newer variometer designs directly measure the static pressure of the atmosphere using a pressure sensor and detect changes in altitude directly from the change in air pressure instead of by measuring air flow. These designs tend to be smaller as they do not need the air bottle. They are more reliable as there

9916-500: The compression-ignition diesel engine is seldom used. Starting in the 1930s attempts were made to produce a practical aircraft diesel engine . In general, Diesel engines are more reliable and much better suited to running for long periods of time at medium power settings. The lightweight alloys of the 1930s were not up to the task of handling the much higher compression ratios of diesel engines, so they generally had poor power-to-weight ratios and were uncommon for that reason, although

10050-425: The control stick, thus creating friction between the skid and the ground. The wing tips also have small skids or wheels to protect the wing tips from ground contact. In most high performance gliders the undercarriage can be raised to reduce drag in flight and lowered for landing. Wheel brakes are provided to allow stopping once on the ground. These may be engaged by fully extending the spoilers/air-brakes or by using

10184-593: The cylinders arranged evenly around the crankshaft, although some early engines, sometimes called semi-radials or fan configuration engines, had an uneven arrangement. The best known engine of this type is the Anzani engine, which was fitted to the Bleriot XI used for the first flight across the English Channel in 1909. This arrangement had the drawback of needing a heavy counterbalance for the crankshaft, but

10318-486: The cylinders in a circle around the crankcase, as in a radial engine, (see above), but the crankshaft is fixed to the airframe and the propeller is fixed to the engine case, so that the crankcase and cylinders rotate. The advantage of this arrangement is that a satisfactory flow of cooling air is maintained even at low airspeeds, retaining the weight advantage and simplicity of a conventional air-cooled engine without one of their major drawbacks. The first practical rotary engine

10452-439: The descent to reach the touchdown point. This gives the pilot wide safety margins should unexpected events occur. If such control devices are not sufficient, the pilot may utilize maneuvers such as a forward slip to further steepen the glider slope. Most gliders require assistance to launch, though some have an engine powerful enough to launch unaided. In addition, a high proportion of new gliders have an engine which will sustain

10586-401: The ends of the wings decrease drag and so improve wing efficiency. Special aerodynamic seals are used at the ailerons , rudder and elevator to prevent the flow of air through control surface gaps. Turbulator devices in the form of a zig-zag tape or multiple blow holes positioned in a span-wise line along the wing are used to trip laminar flow air into turbulent flow at a desired location on

10720-581: The engine core is the bypass ratio. Low-bypass engines are preferred for military applications such as fighters due to high thrust-to-weight ratio, while high-bypass engines are preferred for civil use for good fuel efficiency and low noise. High-bypass turbofans are usually most efficient when the aircraft is traveling at 500 to 550 miles per hour (800 to 890 kilometres per hour), the cruise speed of most large airliners. Low-bypass turbofans can reach supersonic speeds, though normally only when fitted with afterburners . The term advanced technology engine refers to

10854-438: The engine works by having a coiled pipe in the combustion chamber that superheats the fuel (propane) before being injected into the air-fuel inlet. In the combustion chamber, the fuel/air mixture ignites and burns, creating thrust as it leaves through the exhaust pipe. Induction and compression of the fuel/air mixture is done both by the pressure of propane as it is injected, along with the sound waves created by combustion acting on

10988-415: The engine's heat-radiating surfaces to the air and tends to cancel reciprocating forces, radials tend to cool evenly and run smoothly. The lower cylinders, which are under the crankcase, may collect oil when the engine has been stopped for an extended period. If this oil is not cleared from the cylinders prior to starting the engine, serious damage due to hydrostatic lock may occur. Most radial engines have

11122-606: The first electric aircraft engine to be awarded a type certificate by EASA for use in general aviation . The E-811 powers the Pipistrel Velis Electro . Limited experiments with solar electric propulsion have been performed, notably the manned Solar Challenger and Solar Impulse and the unmanned NASA Pathfinder aircraft. Many big companies, such as Siemens, are developing high performance electric engines for aircraft use, also, SAE shows new developments in elements as pure Copper core electric motors with

11256-399: The first engines to use multiple spools —concentric shafts that are free to rotate at their own speed—to let the engine react more quickly to changing power requirements. Turbofans are coarsely split into low-bypass and high-bypass categories. Bypass air flows through the fan, but around the jet core, not mixing with fuel and burning. The ratio of this air to the amount of air flowing through

11390-456: The flight for later analysis. Variometers are also used in radio controlled gliders. Each variometer system consists of a radio transmitter in the glider, and a receiver on the ground for use by the pilot. Depending on the design, the receiver may give the pilot the current altitude of the glider, and a display that indicates if the glider is gaining or losing altitude—often via an audio tone. Other forms of telemetry may also be provided by

11524-558: The glass-fiber Libelle of the 1960s increased that to 36:1, and modern flapped 18 meter gliders such as the ASG29 have a glide ratio of over 50:1. The largest open-class glider, the Eta , has a span of 30.9 meters and has a glide ratio over 70:1. Compare this to the Gimli Glider , a Boeing 767 which ran out of fuel mid-flight and was found to have a glide ratio of 12:1, or to

11658-685: The glider in the air, but is insufficiently powerful to launch the glider. Compared with self-launchers these lower powered engines have advantages in weight, lower costs and pilot licensing. The engines can be electric, jet, or two-stroke gasoline. Gliders in continental Europe use metric units, like km/h for airspeed and m/s for lift and sink rate . In the United States, United Kingdom, Australia and some other countries gliders use knots and ft / min in common with commercial aviation worldwide. In addition to an altimeter , compass , and an airspeed indicator , gliders are often equipped with

11792-409: The glider to Earth in a short distance. Early glider designs used skids for landing, but modern types generally land on wheels. Some of the earliest gliders used a dolly with wheels for taking off and the dolly was jettisoned as the glider left the ground, leaving just the skid for landing. A glider may be designed so the center of gravity (CG) is behind the main wheel so the glider sits nose high on

11926-427: The glider. In powered aircraft, this is done by reducing engine thrust. In gliders, other methods are used to either reduce the lift generated by the wing, increase the drag of the entire glider, or both. Glide slope is the distance traveled for each unit of height lost. In a steady wings-level glide with no wind, glide slope is the same as the lift/drag ratio (L/D) of the glider, called "L-over-D". Reducing lift from

12060-531: The ground. Other designs may have the CG forward of the main wheel so the nose rests on a nose-wheel or skid when stopped. Skids are now mainly used only on training gliders such as the Schweizer SGS 2–33 . Skids are around 100 millimetres (4 in) wide by 900 mm (3 ft) long and run from the nose to the main wheel. Skids help with braking after landing by allowing the pilot to put forward pressure on

12194-462: The improvements in aerodynamics , the performance of gliders has increased. One measure of performance is the glide ratio . A ratio of 30:1 means that in smooth air a glider can travel forward 30 meters while losing only 1 meter of altitude. Comparing some typical gliders that might be found in the fleet of a gliding club – the Grunau Baby from the 1930s had a glide ratio of just 17:1,

12328-497: The intake stacks. It was intended as a power plant for personal helicopters and compact aircraft such as Microlights. A few aircraft have used rocket engines for main thrust or attitude control, notably the Bell X-1 and North American X-15 . Rocket engines are not used for most aircraft as the energy and propellant efficiency is very poor, but have been employed for short bursts of speed and takeoff. Where fuel/propellant efficiency

12462-410: The leisure activity and sport of gliding (also called soaring). This unpowered aircraft can use naturally occurring currents of rising air in the atmosphere to gain altitude. Sailplanes are aerodynamically streamlined and so can fly a significant distance forward for a small decrease in altitude. In North America the term 'sailplane' is also used to describe this type of aircraft. In other parts of

12596-422: The location of thermals . While rate of climb indicators show altitude changes and hence changes in the potential energy of the sailplane, total-energy variometers indicate changes in the total energy of the sailplane, that is, both its potential energy (due to altitude) and its kinetic energy (due to airspeed)." Most modern sailplanes are equipped with Total Energy compensated variometers. The total energy of

12730-430: The many limitations of the rotary engine so when the static style engines became more reliable and gave better specific weights and fuel consumption, the days of the rotary engine were numbered. The Wankel is a type of rotary engine. The Wankel engine is about one half the weight and size of a traditional four-stroke cycle piston engine of equal power output, and much lower in complexity. In an aircraft application,

12864-433: The modern generation of jet engines. The principle is that a turbine engine will function more efficiently if the various sets of turbines can revolve at their individual optimum speeds, instead of at the same speed. The true advanced technology engine has a triple spool, meaning that instead of having a single drive shaft, there are three, in order that the three sets of blades may revolve at different speeds. An interim state

12998-463: The most common Avgas is 100LL. This refers to the octane rating (100 octane) and the lead content (LL = low lead, relative to the historic levels of lead in pre-regulation Avgas). Refineries blend Avgas with tetraethyllead (TEL) to achieve these high octane ratings, a practice that governments no longer permit for gasoline intended for road vehicles. The shrinking supply of TEL and the possibility of environmental legislation banning its use have made

13132-404: The new AE300 turbodiesel , also based on a Mercedes engine. Competing new Diesel engines may bring fuel efficiency and lead-free emissions to small aircraft, representing the biggest change in light aircraft engines in decades. While military fighters require very high speeds, many civil airplanes do not. Yet, civil aircraft designers wanted to benefit from the high power and low maintenance that

13266-408: The overall flight by studying the cloud formations to be used next." In modern gliders, most electronic variometers generate a sound whose pitch and rhythm depends on the instrument reading. Typically the audio tone increases in frequency as the variometer shows a higher rate of climb and decreases in frequency towards a deep groan as the variometer shows a faster rate of descent. When the variometer

13400-534: The past many gliders were not. These types did not soar . They were simply engine-less aircraft towed by another aircraft to a desired destination and then cast off for landing. The prime example of non-soaring gliders were military gliders (such as those used in the Second World War). They were often used just once and then usually abandoned after landing, having served their purpose. Motor gliders are gliders with engines which can be used for extending

13534-568: The pilot can switch the engine on and off in flight without retracting the propeller. Sir George Cayley 's gliders achieved brief wing-borne hops from around 1849. In the 1890s, Otto Lilienthal built gliders using weight shift for control. In the early 1900s, the Wright Brothers built gliders using movable surfaces for control. In 1903, they successfully added an engine. After World War I gliders were first built for sporting purposes in Germany. Germany's strong links to gliding were to

13668-491: The pilot could pull back on the stick, trading the extra speed for altitude again. A compensated variometer uses both speed and altitude to indicate the change in total energy. So the pilot that pushes the stick forward, diving to gain speed, and then pulls back again to regain altitude will notice no change in total energy on a compensated variometer (neglecting energy loss due to drag). According to Helmut Reichmann , "The word 'variometer' means literally 'change meter,' and this

13802-424: The pilot more opportunity to search for promising looking clouds and other signs of lift. A variometer that produces this type of audible tone is known as an "audio variometer". Advanced electronic variometers in gliders can present other information to the pilot from GPS receivers. The display can thus show the bearing, distance and height required to reach an objective. In cruise mode (used in straight flight),

13936-436: The pilot needs to know the glider's vertical speed instead of that of the air mass. The Relative Netto Variometer (or sometimes the super Netto ) includes a g-sensor to detect thermalling. When thermalling, the sensor will detect acceleration (gravity plus centrifugal) above 1 g and tell the relative netto variometer to stop subtracting the sailplane's wing load-adjusted polar sink rate for the duration. Some earlier nettos used

14070-483: The point of view of the pilot looking forward, so for example on a four-engine aircraft such as the Boeing 747 , engine No. 1 is on the left side, farthest from the fuselage, while engine No. 3 is on the right side nearest to the fuselage. In the case of the twin-engine English Electric Lightning , which has two fuselage-mounted jet engines one above the other, engine No. 1 is below and to the front of engine No. 2, which

14204-432: The power-to-weight ratio is very important, making the Wankel engine a good choice. Because the engine is typically constructed with an aluminium housing and a steel rotor, and aluminium expands more than steel when heated, a Wankel engine does not seize when overheated, unlike a piston engine. This is an important safety factor for aeronautical use. Considerable development of these designs started after World War II , but at

14338-423: The pressure inside the bottle and outside the aircraft. The rate and direction of flowing air is measured by the cooling of one of two self-heating thermistors and the difference between the thermistor resistances will cause a voltage difference; this is amplified and displayed to the pilot. The faster the aircraft is ascending (or descending), the faster the air flows. Air flowing out of the bottle indicates that

14472-675: The pressure reduces as speed increases, compensating for the increased static pressure due to sink. According to Helmut Reichmann , "...the least sensitive venturi mounting point would appear to be on the upper quarter of the vertical fin, some 60 cm (2 feet) forward of the leading edge." Venturi compensator types include the Irving Venturi (1948), the Althaus Venturi, the Hüttner Venturi, the Brunswick Tube,

14606-413: The problem of how fast a pilot should cruise between thermals, given both the average lift the pilot expects in the next thermal climb, as well as the amount of lift or sink encountered in cruise mode. Electronic variometers make the same calculations automatically, after allowing for factors such as the glider's theoretical performance , water ballast, headwinds/tailwinds and insects on the leading edges of

14740-485: The range achievable in direct sun on a hot day. Color is not used except for a few small bright patches on wing tips; these patches (typically orange or red) improving a glider's visibility to other airborne aircraft. Such patches are obligatory for mountain flying in France. Non-fibreglass gliders made of aluminum or wood are not so subject to deterioration at higher temperatures and are often quite brightly painted. There

14874-456: The sailplane is towed behind a powered aircraft using a rope about 60 metres (200 ft) long. The sailplane pilot releases the rope after reaching the desired altitude. However, the rope can be released by the towplane also in case of emergency. Winch launching uses a powerful stationary engine located on the ground at the far end of the launch area. The sailplane is attached to one end of 800 to 1,200 metres (2,600 to 3,900 ft) of cable and

15008-408: The speed changing, this is an indication of real lift, not "stick lift." Compensated variometers also include information about the speed of the aircraft, so the total energy ( potential and kinetic ) is used, not just the change in altitude. For example, if a pilot pushes forward on the stick, speeding up as the plane dives, an uncompensated variometer only indicates that altitude is being lost. But

15142-417: The speed for best glide the polar sink speed of the sailplane increases roughly with the square of the airspeed. Since the pitot pressure also increases with the square of the speed, one can use it to 'compensate away' the effect of sailplane polar sink over virtually the entire speed range." Tom Brandes states, "Netto is simply the German way of saying 'net,' and a Netto Variometer System (or polar compensator)

15276-470: The sport of gliding moved into a new realm. Variometers also became important in foot-launch hang gliding, where the open-to-air pilot hears the wind but needs the variometer to help him or her to detect regions of rising or sinking air. In early hang gliding, variometers were not needed for the short flights or flights close to ridge lift. But the variometer became key as pilots began making longer flights. The first portable variometer for use in hang gliders

15410-399: The strength of the lift or sink, so that the pilot can concentrate on centering a thermal, watching for other traffic, on navigation, and weather conditions. Rising air is announced to the pilot as a rising tone, with increasing pitch as the lift increases. Conversely, descending air is announced with a lowering tone, which advises the pilot to escape the sink area as soon as possible. (Refer to

15544-504: The system, displaying parameters such as airspeed and battery voltage. Variometers used in radio controlled gliders may or may not feature total energy compensation. Variometers are not essential in radio controlled gliders; a skilled pilot can usually determine if the glider is going up or down via visual cues alone. The use of variometers is prohibited in some soaring contests for radio controlled gliders. Powered flight An aircraft engine , often referred to as an aero engine ,

15678-439: The time the aircraft industry favored the use of turbine engines. It was believed that turbojet or turboprop engines could power all aircraft, from the largest to smallest designs. The Wankel engine did not find many applications in aircraft, but was used by Mazda in a popular line of sports cars . The French company Citroën had developed Wankel powered RE-2  [ fr ] helicopter in 1970's. In modern times

15812-414: The two crankshafts geared together. This type of engine has one or more rows of cylinders arranged around a centrally located crankcase . Each row generally has an odd number of cylinders to produce smooth operation. A radial engine has only one crank throw per row and a relatively small crankcase, resulting in a favorable power-to-weight ratio . Because the cylinder arrangement exposes a large amount of

15946-401: The ultimate destination location). In 1954, Paul MacCready wrote about a sinking speed correction for a total energy venturi. MacCready stated, "In still air...a glider has a different sinking speed at each airspeed...it would be nicer if the variometer automatically added the sink rate, and thus showed the vertical air motion instead of the vertical glider motion. The correction can be made by

16080-707: The underside of a single wing, and also on the fin and rudder . Registration marks are assigned by gliding associations such as the US Soaring Society of America , and are unrelated to national registrations issued by entities such as the US Federal Aviation Administration . This need for visual ID has somewhat been supplanted by GPS position recording. Insignias are useful in two ways: First, they are used in radio communications between gliders, as pilots use their competition number as their call signs . Secondly, to easily tell

16214-413: The use of a glow plug ) powered by glow fuel , a mixture of methanol , nitromethane , and lubricant. Electrically powered model airplanes and helicopters are also commercially available. Small multicopter UAVs are almost always powered by electricity, but larger gasoline-powered designs are under development. Sailplane A glider or sailplane is a type of glider aircraft used in

16348-542: The vario can also give an audible indication of the correct speed to fly depending on whether the air is rising or sinking. The pilot merely has to input the estimated MacCready setting, which is the expected rate of climb in the next acceptable thermal. There is an increasing trend for advanced variometers in gliders towards flight computers (with variometer indications) which can also present information such as controlled airspace, lists of turnpoints and even collision warnings. Some will also store positional GPS data during

16482-428: The variometer, sailplane pilots found it very hard to soar . Although they could readily detect abrupt changes in vertical speed ("in the seat of the pants"), their senses did not allow them to distinguish lift from sink, or strong lift from weak lift. The actual climb/sink rate could not even be guessed at, unless there was some clear fixed visual reference nearby. Being near a fixed reference means being near to

16616-423: The water ballast is advantageous if the lift is likely to be strong, and may also be used to adjust the glider's center of mass . Moving the center of mass toward the rear by carrying water in the vertical stabilizer reduces the required down-force from the horizontal stabilizer and the resultant drag from that down-force. Although heavier gliders have a slight disadvantage when climbing in rising air, they achieve

16750-448: The winch rapidly winds it in. The sailplane can gain about 270 to 910 metres (900 to 3,000 ft) of height with a winch launch, depending on the headwind. Less often, automobiles are used to pull sailplanes into the air, either by pulling them directly or through the use of a reverse pulley in a similar manner to the winch launch. Elastic ropes (known as bungees ) are occasionally used at some sites to launch gliders from slopes, if there

16884-400: The wing. This flow control prevents the formation of laminar flow bubbles and ensures the absolute minimum drag. Bug-wipers may be installed to wipe the wings while in flight and remove insects that are disturbing the smooth flow of air over the wing. Modern competition gliders carry jettisonable water ballast (in the wings and sometimes in the vertical stabilizer). The extra weight provided by

17018-465: The wings and/or increasing drag will reduce the L/D allowing the glider to descend at a steeper angle with no increase in airspeed. Simply pointing the nose downwards only converts altitude into a higher airspeed with a minimal initial reduction in total energy. Gliders, because of their long low wings, create a high ground effect which can significantly increase the glide angle and make it difficult to bring

17152-643: The wings. Soaring flight computers running specialized soaring software, have been designed for use in gliders. Using GPS technology in conjunction with a barometric device these tools can: After the flight the GPS data may be replayed on computer software for analysis and to follow the trace of one or more gliders against a backdrop of a map, an aerial photograph or the airspace. So that ground-based observers may identify gliders in flight or in gliding competition , registration marks ("insignias" or "competition numbers" or "contest ID") are displayed in large characters on

17286-399: The years after the war, the drawbacks of the turbojet gradually became apparent. Below about Mach 2, turbojets are very fuel inefficient and create tremendous amounts of noise. Early designs also respond very slowly to power changes, a fact that killed many experienced pilots when they attempted the transition to jets. These drawbacks eventually led to the downfall of the pure turbojet, and only

17420-547: Was the Akaflieg Stuttgart FS-24 Phönix which first flew in 1957. This material is still used because of its high strength to weight ratio and its ability to give a smooth exterior finish to reduce drag. Drag has also been minimized by more aerodynamic shapes and retractable undercarriages. Flaps are fitted to the trailing edges of the wings on some gliders to optimise lift and drag at a wide range of speeds. With each generation of materials and with

17554-572: Was the Gnome Omega designed by the Seguin brothers and first flown in 1909. Its relative reliability and good power to weight ratio changed aviation dramatically. Before the first World War most speed records were gained using Gnome-engined aircraft, and in the early years of the war rotary engines were dominant in aircraft types for which speed and agility were paramount. To increase power, engines with two rows of cylinders were built. However,

17688-552: Was the Colver Variometer, introduced in the 1970s by Colver Soaring Instruments, which served to extend the sport into cross-country thermal flying. In the 1980s, Ball Variometers Inc., founded in 1971 by Richard Harding Ball (1921–2011), produced a wrist variometer powered by a 9-volt battery. As the sport of gliding developed, however, it was found that these very simple "uncompensated" instruments had their limitations. The information that glider pilots really need to soar

17822-426: Was the German unmanned V1 flying bomb of World War II . Though the same engines were also used experimentally for ersatz fighter aircraft, the extremely loud noise generated by the engines caused mechanical damage to the airframe that was sufficient to make the idea unworkable. The Gluhareff Pressure Jet (or tip jet) is a type of jet engine that, like a valveless pulsejet, has no moving parts. Having no moving parts,

17956-487: Was used to avoid the spark plugs oiling up. In military aircraft designs, the large frontal area of the engine acted as an extra layer of armor for the pilot. Also air-cooled engines, without vulnerable radiators, are slightly less prone to battle damage, and on occasion would continue running even with one or more cylinders shot away. However, the large frontal area also resulted in an aircraft with an aerodynamically inefficient increased frontal area. Rotary engines have

#56943