Moose River Gold Mines is a Canadian rural community located in Nova Scotia 's Halifax Regional Municipality . It is at the junction of Moose River Road and Mooseland Road. No numbered highways run through Moose River Gold Mines. Gold was discovered in the area in 1866 and mining started in the 1870s. Interest waned around 1900 but rose in the 1930s. The community gained international attention in 1936 when three men were trapped in the mine.
71-525: Gold was first discovered in the area in 1866, but no mining took place until the 1870s when the area became known as the Moose River Gold District. Interest waned in the early 1900s but resumed in the 1930s and the mine was brought back into production in 1935. These historic workings produced some 26,000 troy ounces (810 kg) of gold, which was largely taken from quartz veins, but some also from open slate quarries. On April 12, 1936,
142-458: A geotechnical investigation or environmental site assessment (a so-called Phase II ESA). This includes holes advanced to collect soil samples, water samples or rock cores, to advance in situ sampling equipment, or to install monitoring wells or piezometers . Samples collected from boreholes are often tested in a laboratory to determine their physical properties, or to assess levels of various chemical constituents or contaminants. Typically,
213-444: A geotechnical investigation , environmental site assessment , mineral exploration , temperature measurement, as a pilot hole for installing piers or underground utilities, for geothermal installations, or for underground storage of unwanted substances, e.g. in carbon capture and storage . Engineers and environmental consultants use the term borehole to collectively describe all of the various types of holes drilled as part of
284-442: A borehole used as a water well is completed by installing a vertical pipe (casing) and well screen to keep the borehole from caving. This also helps prevent surface contaminants from entering the borehole and protects any installed pump from drawing in sand and sediment. Oil and natural gas wells are completed in a similar, albeit usually more complex, manner. As detailed in proxy (climate) , borehole temperature measurements at
355-456: A caisson vertically below the top of the aquifer and then advancing lateral collectors out of the caisson and beneath the surface water body. Pumping from within the caisson induces infiltration of water from the surface water body into the aquifer, where it is collected by the collector well laterals and conveyed into the caisson where it can be pumped to the ground surface. Two additional broad classes of well types may be distinguished, based on
426-470: A circulation fluid to displace cuttings and cool bits during the drilling. Another form of rotary-style drilling, termed mud rotary , makes use of a specially made mud, or drilling fluid, which is constantly being altered during the drill so that it can consistently create enough hydraulic pressure to hold the side walls of the bore hole open, regardless of the presence of a casing in the well. Typically, boreholes drilled into solid rock are not cased until after
497-435: A confined space, it displaces oxygen, reducing oxygen concentration to a level low enough to pose a threat to humans and other aerobic organisms but still high enough for a risk of spontaneous or externally caused explosion. This potential for explosion is what poses such a danger in regards to the drilling and placement of water wells. Low levels of methane in drinking water are not considered toxic. When methane seeps into
568-993: A depth of 13 metres (43 ft). Other slightly younger wells are known from this site and from neighbouring Parekklisha-Shillourokambos. A first stone lined well of 5.5 metres (18 ft) depth is documented from a drowned final PPN (c. 7000 BC) site at ‘Atlit-Yam off the coast near modern Haifa in Israel . Wood-lined wells are known from the early Neolithic Linear Pottery culture , for example in Ostrov, Czech Republic, dated 5265 BC, Kückhoven (an outlying centre of Erkelenz ), dated 5300 BC, and Eythra in Schletz (an outlying centre of Asparn an der Zaya ) in Austria , dated 5200 BC. The neolithic Chinese discovered and made extensive use of deep drilled groundwater for drinking. The Chinese text The Book of Changes , originally
639-686: A divination text of the Western Zhou dynasty (1046 -771 BC), contains an entry describing how the ancient Chinese maintained their wells and protected their sources of water. A well excavated at the Hemedu excavation site was believed to have been built during the neolithic era. The well was cased by four rows of logs with a square frame attached to them at the top of the well. 60 additional tile wells southwest of Beijing are also believed to have been built around 600 BC for drinking and irrigation. In Egypt , shadoofs and sakias are used. The sakia
710-550: A drilling action. Unlike rotary drilling, cable tool drilling requires the drilling action to be stopped so that the bore hole can be bailed or emptied of drilled cuttings. Cable tool drilling rigs are rare as they tend to be 10x slower to drill through materials compared to similar diameter rotary air or rotary mud equipped rigs. Drilled wells are usually cased with a factory-made pipe, typically steel (in air rotary or cable tool drilling) or plastic / PVC (in mud rotary wells, also present in wells drilled into solid rock). The casing
781-547: A few to several hundred boreholes, and in practice, depths have ranged from 50 to 300 metres (150 to 1,000 ft). Borehole drilling has a long history. By at least the Han dynasty (202 BC – 220 AD), the Chinese used deep borehole drilling for mining and other projects. The British sinologist and historian Michael Loewe states that borehole sites could reach as deep as 600 metres (2,000 ft). K.S. Tom describes
SECTION 10
#1732773367200852-743: A group of synthetic organofluorine chemical compounds that have multiple fluorine atoms attached to an alkyl chain. PFAS are a group of "forever chemicals" that spread very quickly and very far in ground water polluting it permanently. Water wells near certain airports where any form fire fighting or training activities occurred up to 2010 are likely to be contaminated by PFAS. A study concluded that of ~39 million groundwater wells 6-20% are at high risk of running dry if local groundwater levels decline by less than five meters, or – as with many areas and possibly more than half of major aquifers – continue to decline. Springs and wells have had cultural significance since prehistoric times, leading to
923-450: A hardened drive point and a screen of perforated pipe, after which a pump is installed to collect the water. Deeper wells can be excavated by hand drilling methods or machine drilling, using a bit in a borehole . Drilled wells are usually cased with a factory-made pipe composed of steel or plastic. Drilled wells can access water at much greater depths than dug wells. Two broad classes of well are shallow or unconfined wells completed within
994-430: A pump. The water often comes from an aquifer or groundwater, and can be easily deepened, which may be necessary if the ground water level drops, by telescoping the lining further down into the aquifer. The yield of existing hand dug wells may be improved by deepening or introducing vertical tunnels or perforated pipes. Drawbacks to hand-dug wells are numerous. It can be impractical to hand dig wells in areas where hard rock
1065-433: A screening device, filter pack, slotted casing, or open bore hole is left to allow the flow of water into the well. Constructed screens are typically used in unconsolidated formations (sands, gravels, etc.), allowing water and a percentage of the formation to pass through the screen. Allowing some material to pass through creates a large area filter out of the rest of the formation, as the amount of material present to pass into
1136-406: A segmented steel drilling string, typically made up of 3m (10ft), 6 m (20 ft) to 8m (26ft) sections of steel tubing that are threaded together, with a bit or other drilling device at the bottom end. Some rotary drilling machines are designed to install (by driving or drilling) a steel casing into the well in conjunction with the drilling of the actual bore hole. Air and/or water is used as
1207-484: A series of different depths can be effectively " inverted " (a mathematical formula to solve a matrix equation) to help estimate historic surface temperatures. Clusters of small-diameter boreholes equipped with heat exchangers made of plastic PEX pipe can be used to store heat or cold between opposing seasons in a mass of native rock. The technique is called seasonal thermal energy storage . Media that can be used for this technique ranges from gravel to bedrock. There can be
1278-420: A variety of tools including electro-seismic surveying, any available information from nearby wells, geologic maps, and sometimes geophysical imaging . These professionals provide advice that is almost as accurate a driller who has experience and knowledge of nearby wells/bores and the most suitable drilling technique based on the expected target depth. Shallow pumping wells can often supply drinking water at
1349-571: A very important source of potable water in some rural developing areas, where they are routinely dug and used today. Their indispensability has produced a number of literary references, literal and figurative, including the reference to the incident of Jesus meeting a woman at Jacob 's well ( John 4:6) in the Bible and the " Ding Dong Bell " nursery rhyme about a cat in a well. Hand-dug wells are excavations with diameters large enough to accommodate one or more people with shovels digging down to below
1420-615: A very low cost. However, impurities from the surface easily reach shallow sources, which leads to a greater risk of contamination for these wells compared to deeper wells. Contaminated wells can lead to the spread of various waterborne diseases . Dug and driven wells are relatively easy to contaminate; for instance, most dug wells are unreliable in the majority of the United States. Some research has found that, in cold regions, changes in river flow and flooding caused by extreme rainfall or snowmelt can degrade well water quality. Most of
1491-648: A water supply, it is commonly referred to as "methane migration". This can be caused by old natural gas wells near water well systems becoming abandoned and no longer monitored. Lately, however, the described wells/pumps are no longer very efficient and can be replaced by either handpumps or treadle pumps . Another alternative is the use of self-dug wells, electrical deep-well pumps (for higher depths). Appropriate technology organizations as Practical Action are now supplying information on how to build/set-up ( DIY ) handpumps and treadle pumps in practice. Per- and polyfluoroalkyl substances ( PFAS or PFASs ) are
SECTION 20
#17327733672001562-693: Is a common problem with groundwater. Nitrates from sewage , sewage sludge or fertilizer are a particular problem for babies and young children. Pollutant chemicals include pesticides and volatile organic compounds from gasoline , dry-cleaning , the fuel additive methyl tert-butyl ether (MTBE), and perchlorate from rocket fuel, airbag inflators, and other artificial and natural sources. Several minerals are also contaminants, including lead leached from brass fittings or old lead pipes, chromium VI from electroplating and other sources, naturally occurring arsenic , radon , and uranium —all of which can cause cancer—and naturally occurring fluoride , which
1633-401: Is an excavation or structure created on the earth by digging , driving, or drilling to access liquid resources, usually water . The oldest and most common kind of well is a water well, to access groundwater in underground aquifers . The well water is drawn up by a pump , or using containers, such as buckets that are raised mechanically or by hand. Water can also be injected back into
1704-399: Is caused when the water table of the soil drops over time and salt begins to accumulate. In turn, the increased amount of salt begins to dry the soil out. The increased level of salt in the soil can result in the degradation of soil and can be very harmful to vegetation. Methane , an asphyxiant, is a chemical compound that is the main component of natural gas. When methane is introduced into
1775-437: Is constructed by welding, either chemically or thermally, segments of casing together. If the casing is installed during the drilling, most drills will drive the casing into the ground as the bore hole advances, while some newer machines will actually allow for the casing to be rotated and drilled into the formation in a similar manner as the bit advancing just below. PVC or plastic is typically solvent welded and then lowered into
1846-455: Is desirable in low quantities to prevent tooth decay , but can cause dental fluorosis in higher concentrations. Some chemicals are commonly present in water wells at levels that are not toxic, but can cause other problems. Calcium and magnesium cause what is known as hard water , which can precipitate and clog pipes or burn out water heaters. Iron and manganese can appear as dark flecks that stain clothing and plumbing, and can promote
1917-473: Is drilled to a predetermined depth or to a confining formation (clay or bedrock, for example), and then a smaller hole for the well is completed from that point forward. The well is typically cased from the surface down into the smaller hole with a casing that is the same diameter as that hole. The annular space between the large bore hole and the smaller casing is filled with bentonite clay , concrete, or other sealant material. This creates an impermeable seal from
1988-671: Is much more efficient, as it can bring up water from a depth of 10 metres (versus the 3 metres of the shadoof). The sakia is the Egyptian version of the noria . Some of the world's oldest known wells, located in Cyprus, date to 7000–8,500 BC. Two wells from the Neolithic period, around 6500 BC, have been discovered in Israel. One is in Atlit, on the northern coast of Israel, and the other is in
2059-600: Is present, and they can be time-consuming to dig and line even in favourable areas. Because they exploit shallow aquifers, the well may be susceptible to yield fluctuations and possible contamination from surface water, including sewage. Hand dug well construction generally requires the use of a well trained construction team, and the capital investment for equipment such as concrete ring moulds, heavy lifting equipment, well shaft formwork, motorized de-watering pumps, and fuel can be large for people in developing countries. Construction of hand dug wells can be dangerous due to collapse of
2130-477: Is simply hammered into the ground, usually with a tripod and driver , with pipe sections added as needed. A driver is a weighted pipe that slides over the pipe being driven and is repeatedly dropped on it. When groundwater is encountered, the well is washed of sediment and a pump installed. Drilled wells are constructed using various types of drilling machines, such as top-head rotary, table rotary, or cable tool, which all use drilling stems that rotate to cut into
2201-432: Is still the case in rural areas of the developing world. These wells are inexpensive and low-tech as they use mostly manual labour, and the structure can be lined with brick or stone as the excavation proceeds. A more modern method called caissoning uses pre-cast reinforced concrete well rings that are lowered into the hole. Driven wells can be created in unconsolidated material with a well hole structure, which consists of
Moose River Gold Mines - Misplaced Pages Continue
2272-576: The Cairo Citadel at 280 feet (85 m) deep and the Pozzo di San Patrizio (St. Patrick's Well) built in 1527 in Orvieto, Italy , at 61 metres (200 ft) deep by 13 metres (43 ft) wide are both larger by volume. Driven wells may be very simply created in unconsolidated material with a well hole structure , which consists of a hardened drive point and a screen (perforated pipe). The point
2343-508: The bacteria , viruses , parasites , and fungi that contaminate well water comes from fecal material from humans and other animals. Common bacterial contaminants include E. coli , Salmonella , Shigella , and Campylobacter jejuni . Common viral contaminants include norovirus , sapovirus , rotavirus , enteroviruses , and hepatitis A and E . Parasites include Giardia lamblia , Cryptosporidium , Cyclospora cayetanensis , and microsporidia . Chemical contamination
2414-710: The filtration of the contaminants of concern, and additional protection may be garnered by installing well-casing screens only at depths where contamination is not present. Wellwater for personal use is often filtered with reverse osmosis water processors; this process can remove very small particles. A simple, effective way of killing microorganisms is to bring the water to a full boil for one to three minutes, depending on location. A household well contaminated by microorganisms can initially be treated by shock chlorination using bleach, generating concentrations hundreds of times greater than found in community water systems; however, this will not fix any structural problems that led to
2485-444: The water table . The excavation is braced horizontally to avoid landslide or erosion endangering the people digging. They can be lined with stone or brick; extending this lining upwards above the ground surface to form a wall around the well serves to reduce both contamination and accidental falls into the well. A more modern method called caissoning uses reinforced concrete or plain concrete pre-cast well rings that are lowered into
2556-728: The Jezreel Valley. Wells for other purposes came along much later, historically. The first recorded salt well was dug in the Sichuan province of China around 2,250 years ago. This was the first time that ancient water well technology was applied successfully for the exploitation of salt, and marked the beginning of Sichuan's salt drilling industry. The earliest known oil wells were also drilled in China, in 347 CE. These wells had depths of up to about 240 metres (790 ft) and were drilled using bits attached to bamboo poles. The oil
2627-612: The Russian island Sakhalin . The Chayvo Z-44 extended-reach well took the title of the world's longest borehole on 27 August 2012. Z-44's total measured depth is 12,376 metres (40,604 ft). However, ERD wells are more shallow than the Kola Borehole, owing to a large horizontal displacement. In July 2023, China began drilling deep boreholes, one at the Sichuan Basin expected to reach 10,520 metres (34,510 ft) into
2698-467: The Touquoy zone, after a former mine owned by Damas Touquoy. DDV Gold Ltd. applied to operate an open pit gold mine in 2007. Deposits at the project named Touquoy hold an estimated 635,000 troy ounces (19.8 t) of gold, worth $ 700 million in 2012. The surface operation will involve drilling, blasting, and gold cyanidation to process the ore. The Moose River Gold Mines site will also process ore from
2769-489: The aquifer through the well. Wells were first constructed at least eight thousand years ago and historically vary in construction from a sediment of a dry watercourse to the qanats of Iran, and the stepwells and sakiehs of India. Placing a lining in the well shaft helps create stability, and linings of wood or wickerwork date back at least as far as the Iron Age . Wells have traditionally been sunk by hand digging, as
2840-402: The borehole is lined with materials like bricks, stones, or concrete rings. This reinforcement maintains the integrity of the borehole's structure and helps to prevent contamination. A concrete platform or slab may be installed at the bottom to prevent sediment from entering the water. The top of the borehole is capped to protect it from debris and contamination. Monitoring well A well
2911-461: The casing during construction and filling the casing annulus with an appropriate sealing material. The sealing material (grout) should be placed from immediately above the production zone back to surface, because, in the absence of a correctly constructed casing seal, contaminated fluid can travel into the well through the casing annulus. Centering devices are important (usually one per length of casing or at maximum intervals of 9 m) to ensure that
Moose River Gold Mines - Misplaced Pages Continue
2982-426: The company's mine at its Beaver Dam deposit, 37 km away, which has an estimated yield of 426,600 troy ounces (13.27 t). This will save the construction of a second tailings pond, and an old bush road will be upgraded to facilitate transport. The Moose River mine will have a life of five years and Beaver Dam just three. There are more deposits at Cochrane Hill and Fifteen Mile Stream, 57 km away. Despite
3053-483: The contamination and generally requires some expertise and testing for effective application. After the filtration process, it is common to implement an ultraviolet (UV) system to kill pathogens in the water. UV light affects the DNA of the pathogen by UV-C photons breaking through the cell wall. UV disinfection has been gaining popularity in the past decades as it is a chemical-free method of water treatment. A risk with
3124-428: The controversy of land expropriation, production is expected to begin in 2015 or 2016. Borehole A borehole is a narrow shaft bored in the ground, either vertically or horizontally. A borehole may be constructed for many different purposes, including the extraction of water ( drilled water well and tube well ), other liquids (such as petroleum ), or gases (such as natural gas ). It may also be part of
3195-588: The course of fifty-six hours, and was picked up by the BBC and broadcast to Europe . It was the first live 24-hour radio coverage of a breaking news story in Canada. The following year a Hollywood movie, Draegerman Courage , was made about the events in Moose River and cave-in at the mine, trapping three men. The 'Draegerman' that the title refers to is a man whose job it is to clean up cave-ins in mines and rescue
3266-522: The design and installation of private and municipal septic systems take all these factors into account so that nearby drinking water sources are protected. Education of the general population in society also plays an important role in protecting drinking water. Cleanup of contaminated groundwater tends to be very costly. Effective remediation of groundwater is generally very difficult. Contamination of groundwater from surface and subsurface sources can usually be dramatically reduced by correctly centering
3337-424: The drilled well, vertically stacked with their ends nested and either glued or splined together. The sections of casing are usually 6 metres (20 ft) or more in length, and 4 to 12 in (10 to 30 cm) in diameter, depending on the intended use of the well and local groundwater conditions. Surface contamination of wells in the United States is typically controlled by the use of a surface seal . A large hole
3408-434: The drilling process is completed, regardless of the machinery used. The oldest form of drilling machinery is the cable tool , still used today. Specifically designed to raise and lower a bit into the bore hole, the spudding of the drill causes the bit to be raised and dropped onto the bottom of the hole, and the design of the cable causes the bit to twist at approximately 1 ⁄ 4 revolution per drop, thereby creating
3479-608: The drilling process: "The Chinese method of deep drilling was accomplished by a team of men jumping on and off a beam to impact the drilling bit while the boring tool was rotated by buffalo and oxen." This was the same method used for extracting petroleum in California during the 1860s (i.e. "kicking her down"). A Western Han dynasty bronze foundry discovered in Xinglong, Hebei had nearby mining shafts which reached depths of 100 metres (330 ft) with spacious mining areas;
3550-425: The drilling rig. Especially in developing countries many boreholes are stull dug by hand. The digging begins with manual labor using basic tools such as shovels, picks, and crowbars. Workers excavate the soil layer by layer, often using a circular motion to create a well-shaped hole. The process is slow and demanding, requiring teamwork and coordination. To prevent the walls from collapsing and to ensure water quality,
3621-513: The formation, thus the term "drilling." Drilled wells can be excavated by simple hand drilling methods (augering, sludging, jetting, driving, hand percussion) or machine drilling (auger, rotary, percussion, down the hole hammer). Deep rock rotary drilling method is most common. Rotary can be used in 90% of formation types (consolidated). Drilled wells can get water from a much deeper level than dug wells can − often down to several hundred metres. Drilled wells with electric pumps are used throughout
SECTION 50
#17327733672003692-476: The ground and the other at the Tarim Basin with a planned depth of 11,100 metres (36,400 ft). Drillers may sink a borehole using a drilling rig or a hand-operated rig. The machinery and techniques to advance a borehole vary considerably according to manufacturer, geological conditions, and the intended purpose. For offshore drilling floating units or platforms supported by the seafloor are used for
3763-427: The grouted annular space is of even thickness. Upon the construction of a new test well, it is considered best practice to invest in a complete battery of chemical and biological tests on the well water in question. Point-of-use treatment is available for individual properties and treatment plants are often constructed for municipal water supplies that suffer from contamination. Most of these treatment methods involve
3834-694: The growth of iron and manganese bacteria that can form slimy black colonies that clog pipes. The quality of the well water can be significantly increased by lining the well, sealing the well head, fitting a self-priming hand pump, constructing an apron, ensuring the area is kept clean and free from stagnant water and animals, moving sources of contamination ( pit latrines , garbage pits, on-site sewer systems ) and carrying out hygiene education. The well should be cleaned with 1% chlorine solution after construction and periodically every 6 months. Well holes should be covered to prevent loose debris, animals, animal excrement, and wind-blown foreign matter from falling into
3905-416: The hole and decomposing. The cover should be able to be in place at all times, including when drawing water from the well. A suspended roof over an open hole helps to some degree, but ideally the cover should be tight fitting and fully enclosing, with only a screened air vent. Minimum distances and soil percolation requirements between sewage disposal sites and water wells need to be observed. Rules regarding
3976-635: The hole. A well-digging team digs under a cutting ring and the well column slowly sinks into the aquifer , whilst protecting the team from collapse of the well bore . Hand-dug wells are inexpensive and low tech (compared to drilling) and they use mostly manual labour to access groundwater in rural locations of developing countries. They may be built with a high degree of community participation, or by local entrepreneurs who specialize in hand-dug wells. They have been successfully excavated to 60 metres (200 ft). They have low operational and maintenance costs, in part because water can be extracted by hand, without
4047-620: The holes varied, the drilling of a single well could last nearly one full decade. It was not up until the 19th century that Europe and the West would catch up and rival ancient Chinese borehole drilling technology. For many years, the world's longest borehole was the Kola Superdeep Borehole in Russia. From 2011 until August 2012 the record was held by the 12,345-metre (40,502 ft) long Sakhalin-I Odoptu OP-11 Well, offshore
4118-406: The placement of water wells is soil salination which occurs when the water table of the soil begins to drop and salt begins to accumulate as the soil begins to dry out. Another environmental problem that is very prevalent in water well drilling is the potential for methane to seep through. The potential for soil salination is a large risk when choosing the placement of water wells. Soil salination
4189-604: The roof of the mine collapsed, trapping three men, Herman Magill, David Robertson, and Alfred Scadding, 150 feet (46 m) down for 11 days. The men were reached by drilling a borehole on the sixth day to bring food, water and a telephone until the rescue was completed. Robertson and Scadding survived and Magill died on the seventh day. The event was broadcast by J. Frank Willis of the Canadian Radio Broadcasting Commission (CRBC) to more than 650 radio stations throughout North America over
4260-478: The screen and the borehole or casing. This allows the water to be filtered of unwanted materials before entering the well and pumping zone. There are two broad classes of drilled-well types, based on the type of aquifer the well is in: A special type of water well may be constructed adjacent to freshwater lakes or streams. Commonly called a collector well but sometimes referred to by the trade name Ranney well or Ranney collector , this type of well involves sinking
4331-411: The shafts and rooms were complete with a timber frame, ladders and iron tools. By the first century BC, Chinese craftsmen cast iron drill bits and drillers were able to drill boreholes up to 1,500 metres (4,900 ft) deep. By the eleventh century AD, the Chinese were able to drill boreholes up to 900 metres (3,000 ft) in depth. Drilling for boreholes was time-consuming and long. As the depth of
SECTION 60
#17327733672004402-431: The surface can easily reach shallow sources and contamination of the supply by pathogens or chemical contaminants needs to be avoided. Well water typically contains more minerals in solution than surface water and may require treatment before being potable. Soil salination can occur as the water table falls and the surrounding soil begins to dry out. Another environmental problem is the potential for methane to seep into
4473-413: The surface to the next confining layer that keeps contaminants from traveling down the outer sidewalls of the casing or borehole and into the aquifer . In addition, wells are typically capped with either an engineered well cap or seal that vents air through a screen into the well, but keeps insects, small animals, and unauthorized persons from accessing the well. At the bottom of wells, based on formation,
4544-403: The survivors. Today, there is a provincial park with a cairn and there was a plaque where the borehole was drilled, and there is a museum portraying the history of the gold mine. The plaque was stolen sometime before June 28, 2006. It has yet to be recovered. In the 1980s, drilling exploration in the area of the earlier slate workings found significant gold deposits in what became known as
4615-407: The uppermost saturated aquifer at that location, and deep or confined wells, sunk through an impermeable stratum into an aquifer beneath. A collector well can be constructed adjacent to a freshwater lake or stream with water percolating through the intervening material. The site of a well can be selected by a hydrogeologist , or groundwater surveyor. Water may be pumped or hand drawn. Impurities from
4686-418: The use of the well: A water well constructed for pumping groundwater can be used passively as a monitoring well and a small diameter well can be pumped, but this distinction by use is common. Before excavation, information about the geology, water table depth, seasonal fluctuations, recharge area and rate should be found if possible. This work can be done by a hydrogeologist , or a groundwater surveyor using
4757-490: The water. Very early neolithic wells are known from the Eastern Mediterranean : The oldest reliably dated well is from the pre-pottery neolithic (PPN) site of Kissonerga-Mylouthkia on Cyprus . At around 8400 BC a shaft (well 116) of circular diameter was driven through limestone to reach an aquifer at a depth of 8 metres (26 ft). Well 2070 from Kissonerga-Mylouthkia, dating to the late PPN, reaches
4828-515: The well bore, falling objects and asphyxiation, including from dewatering pump exhaust fumes. The Woodingdean Water Well , hand-dug between 1858 and 1862, is the deepest hand-dug well at 392 metres (1,285 ft). The Big Well in Greensburg, Kansas , is billed as the world's largest hand-dug well, at 109 feet (33 m) deep and 32 feet (9.8 m) in diameter. However, the Well of Joseph in
4899-400: The well slowly decreases and is removed from the well. Rock wells are typically cased with a PVC liner/casing and screen or slotted casing at the bottom, this is mostly present just to keep rocks from entering the pump assembly. Some wells utilize a filter pack method, where an undersized screen or slotted casing is placed inside the well and a filter medium is packed around the screen, between
4970-402: The world, typically in rural or sparsely populated areas, though many urban areas are supplied partly by municipal wells. Most shallow well drilling machines are mounted on large trucks, trailers, or tracked vehicle carriages. Water wells typically range from 3 to 18 metres (10–60 ft) deep, but in some areas it can go deeper than 900 metres (3,000 ft). Rotary drilling machines use
5041-521: Was burned to evaporate brine and produce salt . By the 10th century, extensive bamboo pipelines connected oil wells with salt springs. The ancient records of China and Japan are said to contain many allusions to the use of natural gas for lighting and heating. Petroleum was known as Burning water in Japan in the 7th century. Until recent centuries, all artificial wells were pumpless hand-dug wells of varying degrees of sophistication, and they remain
#199800