Misplaced Pages

#669330

146-586: The Fender Stratocaster , colloquially known as the Strat , is a model of electric guitar designed between 1952 and 1954 by Leo Fender , Bill Carson , George Fullerton , and Freddie Tavares . The Fender Musical Instruments Corporation has continuously manufactured the Stratocaster since 1954. It is a double- cutaway guitar, with an extended top "horn" shape for balance. "Stratocaster" and "Strat" are trademark terms belonging to Fender. Guitars that duplicate

292-407: A laser pointer ) usually takes the form of a button and only closes the circuit when the button is depressed. A regular on‑off switch (such as on a flashlight ) has a constant on-off feature. Dual-action switches incorporate both of these features. When a strongly inductive load such as an electric motor is switched off, the current cannot drop instantaneously to zero; a spark will jump across

438-466: A monaural signal. Many guitars with active electronics use a jack with an extra contact normally used for stereo . These guitars use the extra contact to break the ground connection to the on-board battery to preserve battery life when the guitar is unplugged. These guitars require a mono plug to close the internal switch and connect the battery to ground. Standard guitar cables use a high-impedance 1 ⁄ 4 inch (6.35 mm) mono plug. These have

584-460: A multiway switching system for control of lamps by more than two switches. In building wiring, light switches are installed at convenient locations to control lighting and occasionally other circuits. By use of multiple-pole switches, multiway switching control of a lamp can be obtained from two or more places, such as the ends of a corridor or stairwell. A wireless light switch allows remote control of lamps for convenience; some lamps include

730-500: A radio controlled overhead crane may have a large multi-circuit rotary switch to transfer hard-wired control signals from the local manual controls in the cab to the outputs of the remote control receiver. A toggle switch or tumbler switch is a class of electrical switches that are manually actuated by a mechanical lever , handle, or rocking mechanism. Toggle switches are available in many different styles and sizes, and are used in numerous applications. Many are designed to provide

876-417: A sail switch ensures that air flow is adequate in a duct. Pressure switches respond to fluid pressure. The mercury switch consists of a drop of mercury inside a glass bulb with two or more contacts. The two contacts pass through the glass, and are connected by the mercury when the bulb is tilted to make the mercury roll on to them. This type of switch performs much better than the ball tilt switch, as

1022-400: A vibrato embellishment. A plastic pickguard on some guitars protects the body from scratches or covers the control cavity, which holds most of the wiring. The degree to which the choice of woods and other materials in the solid-guitar body (3) affects the sonic character of the amplified signal is disputed. Many believe it is highly significant, while others think the difference between woods

1168-539: A 12" radius. Fender has produced various 'deluxe' modern American Stratocasters with special features. The Strat Plus was produced from 1987 to 1999 and was equipped with Lace Sensor pickups, a roller nut, locking tuners, a TBX tone control and a Hipshot tremsetter. The Strat Plus Deluxe was introduced in 1989 with pickup and tremolo variations. The Strat Ultra was introduced in 1990, again with pickup variations, and also with an ebony fingerboard. The Fender Custom Shop produced an entry level, team built Stratocaster that

1314-525: A United States patent for an Electrical Stringed Musical Instrument and the patent was later issued in 1937. By the time it was patented, other manufacturers were already making their own electric guitar designs. Early electric guitar manufacturers include Rickenbacker in 1932; Dobro in 1933; National, AudioVox and Volu-tone in 1934; Vega , Epiphone (Electrophone and Electar), and Gibson in 1935 and many others by 1936. By early-mid 1935, Electro String Instrument Corporation had achieved success with

1460-590: A built-in system to electrically amplify their output without altering their tone as an alternative to using a separate microphone. The system may consist of piezoelectric pickups mounted under the bridge, or a low-mass microphone (usually a condenser mic) inside the body of the guitar that converts the vibrations in the body into electronic signals. Combinations of these types of pickups may be used, with an integral mixer/preamp/graphic equalizer. Such instruments are called electric acoustic guitars . They are regarded as acoustic guitars rather than electric guitars because

1606-468: A cam. It has an array of terminals, arranged in a circle around the rotor, each of which serves as a contact for the "spoke" through which any one of a number of different electrical circuits can be connected to the rotor. The switch is layered to allow the use of multiple poles, each layer is equivalent to one pole. Usually such a switch has a detent mechanism so it "clicks" from one active position to another rather than stalls in an intermediate position. Thus

SECTION 10

#1732798217670

1752-431: A contact that can be connected to either of two other contacts, a triple-throw has a contact which can be connected to one of three other contacts, etc. In a switch where the contacts remain in one state unless actuated, such as a push-button switch, the contacts can either be normally open (abbreviated " n.o. " or " no ") until closed by operation of the switch, or normally closed (" n.c. " or " nc ") and opened by

1898-453: A distinctive headstock with six tuning pegs mounted inline along a single side; the fingerboard may be maple or another wood, e.g., rosewood , and has at least twenty-one frets . The Stratocaster's body is front- routed for electronics, which are mounted in a plastic pickguard . Most Stratocasters have three single-coil pickups , a pickup selector switch , one volume control and two tone controls. Bridges generally come in two designs:

2044-507: A fixed bridge or a spring-loaded hinged bridge , which lets players "bend" the pitch of notes or chords up or down, or perform vibrato effects. The sound of an electric guitar can be modified by new playing techniques such as string bending , tapping , and hammering-on , using audio feedback , or slide guitar playing. There are several types of electric guitar. Early forms were hollow-body semi-acoustic guitars , while solid body guitars developed later. String configurations include

2190-445: A flat metal blade, hinged at one end, with an insulating handle for operation, and a fixed contact. When the switch is closed, current flows through the hinged pivot and blade and through the fixed contact. Such switches are usually not enclosed. The knife and contacts are typically formed of copper , steel , or brass , depending on the application. Fixed contacts may be backed up with a spring. Several parallel blades can be operated at

2336-576: A folding neck called the "Foldaxe" was designed and built for Chet Atkins by Roger C. Field . Steinberger guitars developed a line of exotic, carbon fiber instruments without headstocks, with tuning done on the bridge instead. Fingerboards vary as much as necks. The fingerboard surface usually has a cross-sectional radius that is optimized to accommodate finger movement for different playing techniques. Fingerboard radius typically ranges from nearly flat (a very large radius) to radically arched (a small radius). The vintage Fender Telecaster , for example, has

2482-562: A given switch design. In electronics, switches are classified according to the arrangement of their contacts. A pair of contacts is said to be " closed " when current can flow from one to the other. When the contacts are separated by an insulating air gap , they are said to be " open ", and no current can flow between them at normal voltages. The terms " make " for closure of contacts and " break " for opening of contacts are also widely used. The terms pole and throw are also used to describe switch contact variations. The number of " poles "

2628-428: A guitar amplifier and speaker. When an electric guitar is played, string movement produces a signal by generating (i.e., inducing ) a small electric current in the magnetic pickups, which are magnets wound with coils of very fine wire. The signal passes through the tone and volume circuits to the output jack, and through a cable to an amplifier . The current induced is proportional to such factors as string density and

2774-519: A hard, polymerized finish. Strings vibrating in the magnetic field of the pickups (3.1, 3.2) produce an electric current in the pickup winding that passes through the tone and volume controls (3.8) to the output jack. Some guitars have piezo pickups, in addition to or instead of magnetic pickups. Some guitars have a fixed bridge (3.4). Others have a spring-loaded hinged bridge called a vibrato bar , tremolo bar , or whammy bar , which lets players bend notes or chords up or down in pitch or perform

2920-700: A heating process. A switch that is operated by another electrical circuit is called a relay . Large switches may be remotely operated by a motor drive mechanism. Some switches are used to isolate electric power from a system, providing a visible point of isolation that can be padlocked if necessary to prevent accidental operation of a machine during maintenance, or to prevent electric shock. An ideal switch would have no voltage drop when closed, and would have no limits on voltage or current rating. It would have zero rise time and fall time during state changes, and would change state without "bouncing" between on and off positions. Practical switches fall short of this ideal; as

3066-447: A mechanism that springs it into another position when released by an operator. The momentary push-button switch is a type of biased switch. The most common type is a "push-to-make" (or normally-open or NO) switch, which makes contact when the button is pressed and breaks when the button is released. Each key of a computer keyboard, for example, is a normally-open "push-to-make" switch. A "push-to-break" (or normally-closed or NC) switch, on

SECTION 20

#1732798217670

3212-658: A neck-through design is difficult or even impossible to repair, depending on the damage. Historically, the bolt-on style has been more popular for ease of installation and adjustment. Since bolt-on necks can be easily removed, there is an after-market in replacement bolt-on necks from companies such as Warmoth and Mighty Mite. Some instruments—notably most Gibson models—continue to use set-in glued necks. Neck-through bodies are somewhat more common in bass guitars. Materials for necks are selected for dimensional stability and rigidity, and some allege that they influence tone. Hardwoods are preferred, with maple , mahogany , and ash topping

3358-434: A rhythm guitarist and a lead guitarist. Many experiments with electrically amplifying the vibrations of a string instrument were made dating back to the early part of the 20th century. Patents from the 1910s show telephone transmitters were adapted and placed inside violins and banjos to amplify the sound. Hobbyists in the 1920s used carbon button microphones attached to the bridge ; however, these detected vibrations from

3504-519: A rosewood fretboard, and maple fretboards would not be re-introduced in large numbers until 1970. In 1960, the available custom colors were standardized with a paint chip chart, many of which were Duco automobile lacquer colors from DuPont available at an additional 5% cost. Inter-departmental DuPont support research provided a flexible basecoat for their wood applications. A single-ply, eight-screw hole white pickguard (changed to an 11-hole three-ply in late 1959) held all electronic components except

3650-513: A rotary switch provides greater pole and throw capabilities than simpler switches do. Other types use a cam mechanism to operate multiple independent sets of contacts. Rotary switches were used as channel selectors on television receivers until the early 1970s, as range selectors on electrical metering equipment, as band selectors on multi-band radios and other similar purposes. In industry, rotary switches are used for control of measuring instruments, switchgear , or in control circuits. For example,

3796-423: A semi-acoustic tone (see below) or both. Semi-acoustic guitars have a hollow body similar to an acoustic guitar and electromagnetic pickups mounted directly into the body. They work in a similar way to solid-body electric guitars except that because the hollow body also vibrates, the pickups convert a combination of string and body vibration into an electrical signal. Many models, known as semi-hollow bodies, have

3942-535: A series of non-conductive blades spanning the distance between switch contacts, and as the arc rises, its length increases as it forms ridges rising into the spaces between the blades, until the arc is too long to stay sustained and is extinguished. A puffer may be used to blow a sudden high velocity burst of gas across the switch contacts, which rapidly extends the length of the arc to extinguish it quickly. Extremely large switches often have switch contacts surrounded by something other than air to more rapidly extinguish

4088-418: A single block of wood, semi-acoustic guitar bodies are made from multiple pieces of wood in an archtop form, a method of construction different from the typical steel string acoustic guitar . The top is formed from a moderately thick piece of wood which is then carved into a thin outward-curving shape, whereas conventional acoustic guitars have a thin, flat top. Some steel-string acoustic guitars include

4234-570: A solid block running through the middle of the soundbox designed to reduce acoustic feedback. They do not provide enough acoustic volume for live performance, but they can be used unplugged for quiet practice. Semi-acoustic guitars are noted for being able to provide a sweet, plaintive, or funky tone. They are used in many genres, including jazz, blues, funk , sixties pop, and indie rock . They generally have cello-style F-shaped sound holes , which can be blocked off to further reduce feedback. Whereas chambered guitars are made, like solid-body guitars, from

4380-543: A spaced humbucking pair, which significantly reduces 50/60 cycle hum. Fender introduced a five-way selector in 1977, making such pickup combinations more stable. The "quacky" or "doinky" tone of the bridge and middle pickups in parallel, popularized by players such as Jimi Hendrix , Eric Clapton , Stevie Ray Vaughan , David Gilmour , Rory Gallagher , Mark Knopfler , Bob Dylan , Eric Johnson , Nile Rodgers , George Harrison , Scott Thurston , Ronnie Wood , John Mayer , Ed King , Robert Cray , can be obtained by using

4526-438: A state where a quarter of the load's rated power (or worse if the load is not purely resistive) is briefly dropped in the switch. For this reason, power switches intended to interrupt a load current have spring mechanisms to make sure the transition between on and off is as short as possible regardless of the speed at which the user moves the rocker. Power switches usually come in two types. A momentary on‑off switch (such as on

Fender Stratocaster - Misplaced Pages Continue

4672-545: A sufficient amount of wetting current is a crucial step in designing systems that use delicate switches with small contact pressure as sensor inputs. Failing to do this might result in switches remaining electrically "open" due to contact oxidation. The moving part that applies the operating force to the contacts is called the actuator , and may be a toggle or dolly , a rocker , a push-button or any type of mechanical linkage (see photo). A switch normally maintains its set position once operated. A biased switch contains

4818-399: A tip and sleeve configuration referred to as a TS phone connector . The voltage is usually around 1 to 9 millivolts . A few guitars, such as Rickenbacker guitars equipped with Rick-O-Sound , feature stereo output. There are a variety of ways the "stereo" effect may be implemented. Commonly, but not exclusively, stereo guitars route the neck and bridge pickups to separate output buses on

4964-404: A toggle mechanism or not. Similarly, a switch where a definitive click is heard, is called a "positive on-off switch". A very common use of this type of switch is to switch lights or other electrical equipment on or off. Multiple toggle switches may be mechanically interlocked to prevent forbidden combinations. In some contexts, particularly computing , a toggle switch, or the action of toggling,

5110-406: A tone control that incorporates a single, shared tone capacitor, whereas the bridge pickup, which is slanted towards the high strings for a more trebly sound, has no tone control for maximum brightness. On many modern Stratocasters, the first tone control affects the neck pickup; the second tone control affects the middle and bridge pickups; on some Artist Series models Buddy Guy signature guitar),

5256-405: A top so heavily reinforced that it essentially functioned as a solid-body instrument. Unlike acoustic guitars, solid-body electric guitars have no vibrating soundboard to amplify string vibration. Instead, solid-body instruments depend on electric pickups, and an amplifier ("amp") and speaker . The solid body ensures that the amplified sound reproduces the string vibration alone, thus avoiding

5402-687: A triple single-coil guitar. The history of electric guitars has been summarized by Guitar World magazine, and the earliest electric guitar on their top 10 list is the Ro-Pat-In Electro A-25 "Frying Pan" (1932) described as "The first-fully functioning solid-body electric guitar to be manufactured and sold". It was the first electric guitar used in a publicly promoted performance, performed by Gage Brewer in Wichita, Kansas in October 1932. The most recent electric guitar on this list

5548-590: A typical small radius of approximately 7.25 inches (18.4 cm). Some manufacturers have experimented with fret profile and material, fret layout, number of frets, and modifications of the fingerboard surface for various reasons. Some innovations were intended to improve playability by ergonomic means, such as Warmoth Guitars' compound radius fingerboard. Scalloped fingerboards added enhanced microtonality during fast legato runs. Fanned frets intend to provide each string with an optimal playing tension and enhanced musicality. Some guitars have no frets , while others, like

5694-409: A way to reduce or counter the sound, as they are designed to "buck" (in the verb sense of oppose or resist ) the hum, hence their name. The high combined inductance of the two coils also leads to the richer, "fatter" tone associated with humbucking pickups. Electric guitar necks vary in composition and shape. The primary metric of guitar necks is the scale length , which is the vibrating length of

5840-409: A wood post with a neck attached and two hollow-body halves attached to the sides for appearance only — shares nothing in common for design or hardware with the solid-body Gibson Les Paul , designed by Ted McCarty and introduced in 1952. The feedback associated with amplified hollow-bodied electric guitars was understood long before Paul's "log" was created in 1940; Gage Brewer's Ro-Pat-In of 1932 had

5986-457: Is a guitar that requires external electric sound amplification in order to be heard at typical performance volumes, unlike a standard acoustic guitar . It uses one or more pickups to convert the vibration of its strings into electrical signals , which ultimately are reproduced as sound by loudspeakers . The sound is sometimes shaped or electronically altered to achieve different timbres or tonal qualities via amplifier settings or knobs on

Fender Stratocaster - Misplaced Pages Continue

6132-400: Is a common problem with mechanical switches, relays and battery contacts , which arises as the result of electrical contact resistance (ECR) phenomena at interfaces. Switch and relay contacts are usually made of springy metals. When the contacts strike together, their momentum and elasticity act together to cause them to bounce apart one or more times before making steady contact. The result

6278-436: Is a manually operated electromechanical device with one or more sets of electrical contacts , which are connected to external circuits. Each set of contacts can be in one of two states: either "closed" meaning the contacts are touching and electricity can flow between them, or "open", meaning the contacts are separated and the switch is nonconducting. The mechanism actuating the transition between these two states (open or closed)

6424-487: Is a rapidly pulsed electric current instead of a clean transition from zero to full current. The effect is usually unimportant in power circuits, but causes problems in some analogue and logic circuits that respond fast enough to misinterpret the on‑off pulses as a data stream. In the design of micro-contacts, controlling surface structure ( surface roughness ) and minimizing the formation of passivated layers on metallic surfaces are instrumental in inhibiting chatter. In

6570-419: Is also very hot and is capable of eroding the metal surfaces of the switch contacts (the same true for vacuum switches). Electric current arcing causes significant degradation of the contacts and also significant electromagnetic interference (EMI), requiring the use of arc suppression methods. Where the voltage is sufficiently high, an arc can also form as the switch is closed and the contacts approach. If

6716-445: Is capable of a multitude of sounds and styles in genres ranging from pop and rock to folk to country music , blues and jazz . It served as a major component in the development of electric blues , rock and roll , rock music , heavy metal music and many other genres of music. Electric guitar design and construction varies greatly in the shape of the body and the configuration of the neck, bridge, and pickups. Guitars may have

6862-447: Is considerable debate about the effects on tone and sustain of the material used in the vibrato system's 'inertia bar' and many aftermarket versions are available. The Stratocaster features three single coil pickups , with the output originally selected by a 3-way switch. Guitarists soon discovered that by positioning the switch in between the first and second position, both the bridge and middle pickups could be selected, and similarly,

7008-558: Is made of solid wood, without functionally resonating air spaces. The first solid-body Spanish standard guitar was offered by Vivi-Tone no later than 1934. This model featured a guitar-shaped body of a single sheet of plywood affixed to a wood frame. Another early, substantially solid Spanish electric guitar, called the Electro Spanish, was marketed by the Rickenbacker guitar company in 1935 and made of Bakelite . By 1936,

7154-406: Is often used in two roles: as a rhythm guitar , which plays the chord sequences or progressions , and riffs , and sets the beat (as part of a rhythm section ); and as a lead guitar , which provides instrumental melody lines, melodic instrumental fill passages, and solos . In a small group, such as a power trio , one guitarist may switch between both roles; in larger groups there is often

7300-418: Is subtle. In acoustic and archtop guitars, wood choices more clearly affect tone. Woods typically used in solid-body electric guitars include alder (brighter, but well rounded), swamp ash (similar to alder, but with more pronounced highs and lows), mahogany (dark, bassy, warm), poplar (similar to alder), and basswood (very neutral). Maple , a very bright tonewood , is also a popular body wood but

7446-468: Is the number of electrically separate switches which are controlled by a single physical actuator. For example, a " 2-pole " switch has two separate, parallel sets of contacts that open and close in unison via the same mechanism. The number of " throws " is the number of separate wiring path choices other than "open" that the switch can adopt for each pole. A single-throw switch has one pair of contacts that can either be closed or open. A double-throw switch has

SECTION 50

#1732798217670

7592-513: Is understood in the different sense of a mechanical or software switch that alternates between two states each time it is activated, regardless of mechanical construction. For example, the caps lock key on a computer causes all letters to be generated in capitals after it is pressed once; pressing it again reverts to lower-case letters. Switches can be designed to respond to any type of mechanical stimulus: for example, vibration (the trembler switch), tilt, air pressure, fluid level (a float switch ),

7738-423: Is usually (there are other types of actions) either an " alternate action " (flip the switch for continuous "on" or "off") or " momentary " (push for "on" and release for "off") type. A switch may be directly manipulated by a human as a control signal to a system, such as a computer keyboard button, or to control power flow in a circuit, such as a light switch . Automatically operated switches can be used to control

7884-450: Is very heavy. For this reason, it is often placed as a "cap" on a guitar made primarily of another wood. Cheaper guitars are often made of cheaper woods, such as plywood , pine , or agathis —not true hardwoods—which can affect durability and tone. Though most guitars are made of wood, any material may be used. Materials such as plastic, metal, and even cardboard have been used in some instruments. The guitar output jack typically provides

8030-582: The Fender Showman amplifier . In the early 1960s, the instrument was also championed by Hank Marvin , guitarist for the Shadows , a band that originally backed Cliff Richard and then produced instrumentals of its own. In December 1964, George Harrison and John Lennon acquired Stratocasters and used them for " Help! ", and onwards. The double unison guitar solo on " Nowhere Man ", was played by Harrison and Lennon on their new Stratocasters. After

8176-692: The Gibson Les Paul , Gibson SG , and Fender Telecaster , it is one of the most-often emulated electric guitar shapes. The guitar introduced into the popular market several features that were innovative for electric guitars in the mid-1950s. The distinctive body shape, which has become commonplace among electric guitars, was revolutionary for the time period, and for the first time a mass-market electric guitar did not significantly resemble earlier acoustic models. The double cutaway, elongated horns, and heavily contoured back were all designed for better balance and comfort to play while standing up and slung off

8322-754: The Gibson SG used by Angus Young from the group AC/DC . Some otherwise solid-bodied guitars, such as the Gibson Les Paul Supreme, the PRS Singlecut, and the Fender Telecaster Thinline , are built with hollow chambers in the body. These chambers are designed to not interfere with the critical bridge and string anchor point on the solid body. In the case of Gibson and PRS, these are called chambered bodies . The motivation for this may be to reduce weight, to achieve

8468-475: The Gittler guitar , have no neck in the traditional sense. Switch Switches are made in many different configurations; they may have multiple sets of contacts controlled by the same knob or actuator, and the contacts may operate simultaneously, sequentially, or alternately. A switch may be operated manually, for example, a light switch or a keyboard button, or may function as a sensing element to sense

8614-485: The Hammond organ , multiple wires are pressed together under the piano keys of the manuals. Their bouncing and non-synchronous closing of the switches is known as Hammond Click and compositions exist that use and emphasize this feature. Some electronic organs have a switchable replica of this sound effect. The effects of contact bounce can be eliminated by: All of these methods are referred to as 'debouncing'. When

8760-584: The Jaguar . During the CBS era, particularly the 1970s, the perceived quality of Fender instruments fell. During this time, vintage instruments from the pre-CBS era became popular. When the Fender company was bought from CBS by a group of investors and employees headed by Bill Schultz in 1985, manufacturing resumed its former high quality, and Fender was able to regain market share and brand reputation. Dan Smith, with

8906-673: The Slingerland company introduced a wooden solid-body electric model, the Slingerland Songster 401 (and a lap steel counterpart, the Songster 400). Gibson's first production electric guitar, marketed in 1936, was the ES-150 model ("ES" for "Electric Spanish", and "150" reflecting the $ 150 price of the instrument, along with matching amplifier). The ES-150 guitar featured a single-coil, hexagonally shaped "bar" pickup, which

SECTION 60

#1732798217670

9052-436: The contact resistance , and wetting current of a mechanical switch. Sometimes the contacts are plated with noble metals , for their excellent conductivity and resistance to corrosion. They may be designed to wipe against each other to clean off any contamination. Nonmetallic conductors, such as conductive plastic, are sometimes used. To prevent the formation of insulating oxides, a minimum wetting current may be specified for

9198-420: The electronics industry such as " single-pole, single-throw " (SPST) (the simplest type, "on or off") or " single-pole, double-throw " (SPDT), connecting either of two terminals to the common terminal. In electrical power wiring (i.e., house and building wiring by electricians ), names generally involve the suffix "-way" ; however, these terms differ between British English and American English (i.e.,

9344-405: The liquid metal connection is unaffected by dirt, debris and oxidation, it wets the contacts ensuring a very low resistance bounce-free connection, and movement and vibration do not produce a poor contact. These types can be used for precision works. It can also be used where arcing is dangerous (such as in the presence of explosive vapour) as the entire unit is sealed. Knife switches consist of

9490-409: The six-string guitar (the most common type), which is usually tuned E, A, D, G, B, E, from lowest to highest strings; the seven-string guitar , which typically adds a low B string below the low E; the eight-string guitar , which typically adds a low E or F# string below the low B; and the twelve-string guitar , which has six two-string courses similar to a mandolin . In rock, the electric guitar

9636-418: The wolf tones and unwanted feedback associated with amplified acoustic guitars. These guitars are generally made of hardwood covered with a hard polymer finish, often polyester or lacquer. In large production facilities, the wood is stored for three to six months in a wood-drying kiln before being cut to shape. Premium custom-built guitars are frequently made with much older , hand-selected wood. One of

9782-589: The "Frying Pan", and set out to capture a new audience through its release of the Electro-Spanish Model B and the Electro-Spanish Ken Roberts , which was the first full 25-inch scale electric guitar ever produced. The Electro-Spanish Ken Roberts was revolutionary for its time, providing players a full 25-inch scale, with easy access to 17 frets free of the body. Unlike other lap-steel electrified instruments produced during

9928-487: The "Original Contour Body") differed from the flat, squared edge design of the Telecaster . The Stratocaster's double cutaways allowed players easier access to higher positions on the neck. The first model offered for sale was the 1954 Fender Stratocaster. The design featured a solid, deeply contoured ash body, a 21-fret one-piece maple neck with black dot inlays, and Kluson SafeTi String post tuning machines. The color

10074-549: The Broadcaster. Another notable solid-body design is the Fender Stratocaster , which was introduced in 1954 and became extremely popular among musicians in the 1960s and 1970s for its wide tonal capabilities and more comfortable ergonomics than other models. Different styles of guitar have different pick-up styles, the main being 2 or 3 " single-coil " pick-ups or a double humbucker , with the Stratocaster being

10220-471: The Fender Stratocasters manufactured were made in a single year, in 1979. The increased 1970s production levels saw a gradual departure from the high quality instruments of the 1960s and the introduction of Japanese manufacturers into the market. Original Stratocasters were manufactured with five vibrato springs (three in late 1953 prototypes) attached to a milled inertia block and anchored to

10366-810: The Highway One and American Special Stratocasters) and the more expensive American Ultra Stratocaster (successor to the American Elite Stratocaster). Fender has also manufactured guitars in East Asia, notably Japan, and in Mexico, where the affordable Player (successor to Standard) series guitars are built. In addition to the Player series, Fender has also released the Player Plus series that features noiseless pickups, locking tuners, and

10512-414: The Stratocaster by other manufacturers are sometimes called S-Type or ST-type guitars. Many prominent rock musicians have been associated with the Stratocaster for use in studio recording and live performances , most notably Eric Clapton , Buddy Holly , David Gilmour , Mark Knopfler , Jimi Hendrix , Stevie Ray Vaughan , John Frusciante , Jeff Beck , George Harrison , and Tom Petty . Along with

10658-449: The amount of movement over the pickups. Because of their natural qualities, magnetic pickups tend to pick up ambient, usually unwanted electromagnetic interference or EMI. This mains hum results in a tone of 50 or 60 cycles per second depending on the powerline frequency of the local alternating current supply. The resulting hum is particularly strong with single-coil pickups. Double-coil or " humbucker " pickups were invented as

10804-551: The arc. A DPDT switch has six connections, but since polarity reversal is a very common usage of DPDT switches, some variations of the DPDT switch are internally wired specifically for polarity reversal. These crossover switches only have four terminals rather than six. Two of the terminals are inputs and two are outputs. When connected to a battery or other DC source, the 4-way switch selects from either normal or reversed polarity. Such switches can also be used as intermediate switches in

10950-461: The arc. For example, the switch contacts may operate in a vacuum, immersed in mineral oil , or in sulfur hexafluoride . In AC power service, the current periodically passes through zero; this effect makes it harder to sustain an arc on opening. Manufacturers may rate switches with lower voltage or current rating when used in DC ;circuits. When a switch is designed to switch significant power,

11096-418: The back of the body. The novel mechanism pivots on a fulcrum design with a six screw bridge plate, allowing the whole set-up to "float" while transferring the strings' energy directly into the body. Though advertised as "Tremolo" (a change in volume amplitude), vibrato is the correct term for pitch variation. In the floating position, players can move the bridge-mounted vibrato tremolo arm up or down to modulate

11242-633: The back of the guitar by metal ferrules . Many believe this design improves a guitar's sustain and timbre . A few examples of string-through body guitars are the Fender Telecaster Thinline , the Fender Telecaster Deluxe , the B.C. Rich IT Warlock and Mockingbird, and the Schecter Omen 6 and 7 series. Compared to an acoustic guitar, which has a hollow body, electric guitars make much less audible sound when their strings are plucked, so electric guitars are normally plugged into

11388-418: The body at the base of the guitar. These appear on Rickenbackers , Gretsches , Epiphones , a wide variety of archtop guitars , particularly jazz guitars , and the 1952 Gibson Les Paul. Pictured is a tremolo arm or vibrato tailpiece - style bridge and tailpiece system, often called a whammy bar or trem . It uses a lever ("vibrato arm") attached to the bridge that can temporarily slacken or tighten

11534-430: The body. Set-in necks are glued to the body at the factory. This is the traditional type of joint. Leo Fender pioneered bolt-on necks on electric guitars to facilitate easy adjustment and replacement. Neck-through instruments extend the neck to the length of the instrument so that it forms the center of the body. While a set-in neck can be carefully unglued by a skilled luthier , and a bolt-on neck can simply be unscrewed,

11680-555: The bridge on top of the instrument, resulting in a weak signal. Electric guitars were originally designed by acoustic guitar makers and instrument manufacturers. The demand for amplified guitars began during the big band era; as orchestras increased in size, guitar players soon realized the necessity in guitar amplification and electrification. The first electric guitars used in jazz were hollow archtop acoustic guitar bodies with electromagnetic transducers . The first electrically amplified stringed instrument to be marketed commercially

11826-546: The closer the fret spacing. Opinions vary regarding the effect of scale length on tone and feel. Popular opinion holds that longer scale length contributes to greater amplitude . Reports of playing feel are greatly complicated by the many factors involved in this perception. String gauge and design, neck construction and relief, guitar setup, playing style, and other factors contribute to the subjective impression of playability or feel. Necks are described as bolt-on , set-in , or neck-through , depending on how they attach to

11972-409: The current decreases to a steady-state value. A switch designed for an incandescent lamp load can withstand this inrush current. Wetting current is the minimum current needing to flow through a mechanical switch while it is operated to break through any film of oxidation that may have been deposited on the switch contacts. The film of oxidation occurs often in areas with high humidity . Providing

12118-414: The design over the years and models with features that differ from the archetypical design. However, the essential character of the design has remained constant. The Stratocaster was the first Fender guitar to feature three pickups and a spring tension vibrato system , as well as being the first Fender with a contoured body. The Stratocaster's sleek, contoured body shape (officially referred to by Fender as

12264-399: The different parts of an electric guitar. The headstock (1) contains the metal machine heads (1.1), which use a worm gear for tuning. The nut (1.4)—a thin fret-like strip of metal, plastic, graphite, or bone—supports the strings at the headstock end of the instrument. The frets (2.3) are thin metal strips that stop the string at the correct pitch when the player pushes a string against

12410-538: The effects of different woods or materials on the electric guitar sound. Several neck shapes appear on guitars, including shapes known as C necks, U necks, and V necks. These refer to the cross-sectional shape of the neck (especially near the nut). Several sizes of fret wire are available, with traditional players often preferring thin frets, and metal shredders liking thick frets. Thin frets are considered better for playing chords, while thick frets allow lead guitarists to bend notes with less effort. An electric guitar with

12556-467: The electric guitar was adopted by jazz guitar players, who wanted to play single-note guitar solos in large big band ensembles. Early proponents of the electric guitar on record include Les Paul , Eddie Durham , George Barnes , Lonnie Johnson , Sister Rosetta Tharpe , T-Bone Walker , and Charlie Christian . During the 1950s and 1960s, the electric guitar became the most important instrument in popular music . It has evolved into an instrument that

12702-617: The finest to ever leave Fender's Fullerton plant, which closed its doors in late 1984. In 1985, Fender's US production of the Vintage reissues resumed into a new 14,000 square feet (1,300 m) factory at Corona, California, located about 20 miles (32 km) away from Fullerton. Some early reissues from 1986 were crafted with leftover parts from the Fullerton factory. Fender released their first Stratocaster signature guitar for Eric Clapton in 1988. A popular Fender Reissue Stratocaster

12848-420: The fingerboard. The truss rod (1.2) is a metal rod (usually adjustable) that counters the tension of the strings to keep the neck straight. Position markers (2.2) provide the player with a reference to the playing position on the fingerboard. The neck and fretboard (2.1) extend from the body. At the neck joint (2.4), the neck is either glued or bolted to the body. The body (3) is typically made of wood with

12994-432: The first improvements on the vibrato system in many years when, in the late 1970s, he experimented with "locking" nuts and bridges that prevent the guitar from losing tuning, even under heavy vibrato bar use. The fourth type of system employs string-through body anchoring. The strings pass over the bridge saddles, then through holes through the top of the guitar body to the back. The strings are typically anchored in place at

13140-432: The first solid-body guitars was invented by Les Paul . Gibson did not present their Gibson Les Paul guitar prototypes to the public, as they did not believe the solid-body style would catch on. Another early solid-body Spanish style guitar, resembling what would become Gibson's Les Paul guitar a decade later, was developed in 1941 by O.W. Appleton, of Nogales, Arizona. Appleton made contact with both Gibson and Fender but

13286-405: The first tone control is a presence circuit that cuts or boosts treble and bass frequencies, affecting all the pickups; the second tone control is an active midrange booster that boosts the midrange frequencies up to 25 dB (12 dB on certain models) to produce a fatter humbucker -like sound. Dick Dale was a prominent Stratocaster player who also collaborated with Leo Fender in developing

13432-442: The floating bridge has an excessive propensity to detune guitars. These guitarists inhibit the bridge's movement with a chunk of wood wedged between the bridge block and the inside cutout of the tremolo cavity, and by increasing the tension on the tremolo springs; these procedures lock the bridge in a fixed position. Some Stratocasters have a fixed bridge in place of the vibrato assembly; these are colloquially called "hard-tails". There

13578-862: The guitar. A stereo cable then routes each pickup to its signal chain or amplifier. For these applications, the most popular connector is a high-impedance 1 ⁄ 4 inch (6.35 mm) plug with a tip, ring, and sleeve configuration, also known as a TRS phone connector . Some studio instruments, notably certain Gibson Les Paul models, incorporate a low- impedance three-pin XLR connector for balanced audio . Many exotic arrangements and connectors exist that support features such as midi and hexaphonic pickups. The bridge and tailpiece , while serving separate purposes, work closely together to affect playing style and tone. There are four basic types of bridge and tailpiece systems on electric guitars. Within these four types are many variants. A hard-tail guitar bridge anchors

13724-404: The guitar. Often, this is done through the use of effects such as reverb , distortion and "overdrive" ; the latter is considered to be a key element of electric blues guitar music and jazz , rock and heavy metal guitar playing. Designs also exist combining attributes of electric and acoustic guitars: the semi-acoustic and acoustic-electric guitars. Invented in 1932 by Johannes Isaac,

13870-405: The guitar. Various other companies have produced their own Strat-style bodies known as Superstrats . The archetypal Stratocaster is a solid-body electric guitar with a contoured asymmetric double-cutaway body with an extended upper horn; the body is usually made from alder or ash. The neck is usually made from maple and attached to the body with screws (often referred to as " bolts ") and has

14016-552: The help of John Page, proceeded to work on a reissue of the most popular guitars of Leo Fender's era. They decided to manufacture two Vintage reissue Stratocaster models, the one-piece maple neck 1957 and a rosewood-fretboard 1962 along with the maple-neck 1952 Telecaster, the maple-neck 1957 and rosewood-fretboard 1962 Precision Basses, as well as the rosewood-fretboard "stacked knob" 1962 Jazz Bass. These first few years (1982–1984) of reissues, known as American Vintage Reissues, are now high-priced collector's items and considered as some of

14162-407: The highest voltages. The disadvantages of the knife switch are the slow opening speed and the proximity of the operator to exposed live parts. Metal-enclosed safety disconnect switches are used for isolation of circuits in industrial power distribution. Sometimes spring-loaded auxiliary blades are fitted which momentarily carry the full current during opening, then quickly part to rapidly extinguish

14308-499: The instrument has a tendency to go out of tune during double-stop string bends. Many Stratocaster players opt to tighten the springs (or even increase the number of springs used) so that the bridge is firmly anchored against the guitar body: in this configuration, the vibrato arm can still be used to slacken the strings and therefore lower the pitch, but it cannot be used to raise the pitch (a configuration sometimes referred to as "dive-only"). Some players, such as Ronnie Wood , feel that

14454-599: The introduction of the Fender Stratocaster Ultra series in 1989, ebony was officially selected as a fretboard material on some models (although several Elite Series Stratocasters manufactured in 1983/84 such as the Gold and Walnut were available with a stained ebony fretboard). In December 1965 the Stratocaster was given a broader headstock with altered decals to match the size of the Jazzmaster and

14600-403: The late 1960s. His remarkable playing style and musical prowess led to a dramatic increase in sales and thrust the Stratocaster into musical history as the premier electric guitar. As they followed Jimi Hendrix's popularity on TV, CBS asked for the word Stratocaster on the headstock be made larger so that people could read the model name easily. Between the years 1954 and 1979, nearly a quarter of

14746-449: The late 1970s, Fender stopped shipping guitars with the bridge cover plate, though some more modern reissue and custom shop models still have them. The innovative tremolo system is balanced by springs mounted in a rear cavity. The output jack is mounted in a recess in the front of the guitar body. Many different colors have been available. The Stratocaster's scale length is 25.5 inches (648 mm). There have been some minor changes to

14892-649: The list. The neck and fingerboard can be made from different materials; for example, a guitar may have a maple neck with a rosewood or ebony fingerboard. Today there are expensive and budget guitars exploring other options for fretboard wood for instance Pau-Ferro , both for availability and cheap price while still maintaining quality. In the 1970s, designers began to use exotic human-made materials such as aircraft-grade aluminum , carbon fiber , and ebonol . Makers known for these unusual materials include John Veleno , Travis Bean , Geoff Gould , and Alembic . Aside from possible engineering advantages, some feel that with

15038-409: The middle and neck pickups could be selected between the 2nd and 3rd position. When two pickups are selected simultaneously, they are wired in parallel which leads to a slight drop in output as slightly more current is allowed to pass to the ground. In newer guitars, since the middle pickup is almost always wired in reverse (and with its magnets having opposite polarity), the intermediate positions create

15184-459: The more common pivoting "tremolo" bridges , and the less common "hardtail" fixed bridge. Both types of bridge have six individually adjustable saddles whose height and intonation can be set independently. Early models of the stratocaster came with a removable metal cover plate that fit over the bridge. The plate was purely cosmetic, and tended to get in the way of important playing techniques such as palm muting , so many players removed it. By

15330-543: The most popular electric guitar in history, Leo Fender made very few alterations to the basic design of the Fender Stratocaster (and the Telecaster for that matter) up until 1965 when the company was sold to CBS Instruments. For example, the bridge cover on the Fender Stratocaster was often taken off by players and either disposed or kept in the case. Despite full knowledge of this, Leo Fender always provided

15476-438: The motions of machines, for example, to indicate that a garage door has reached its full open position or that a machine tool is in a position to accept another workpiece. Switches may be operated by process variables such as pressure, temperature, flow, current, voltage, and force, acting as sensors in a process and used to automatically control a system. For example, a thermostat is a temperature-operated switch used to control

15622-400: The neck shape took a more "V-shaped" feel with deeper body carves on the guitar a noted feature. In 1959, Fender introduced a thick Brazilian rosewood fretboard to the Stratocaster, now colloquially referred to as a "slab-board". This thicker board lasted until 1962, when the fretboard was made with a thinner 'veneer' of Brazilian Rosewood. Nearly all of the 1960s models of the Stratocaster had

15768-401: The new Fender guitars with a bridge cover to prevent corrosion on the bridge parts. After 1965, the Fender company, under the control of CBS Instruments, saw a drop in sales of the Fender Stratocaster to customers. The Fender Jazzmaster had been promoted as the flagship guitar in the Fender line. As such, the resurgence of the Fender Stratocaster is credited to the arrival of Jimi Hendrix in

15914-413: The opening contacts. Switches for inductive loads must be rated to handle these cases. The spark will cause electromagnetic interference if not suppressed; a snubber network of a resistor and capacitor in series will quell the spark. When turned on, an incandescent lamp draws a large inrush current of about ten times the steady-state current; as the filament heats up, its resistance rises and

16060-448: The other hand, breaks contact when the button is pressed and makes contact when it is released. An example of a push-to-break switch is a button used to release a door held closed by an electromagnet . The interior lamp of a household refrigerator is controlled by a switch that is held open when the door is closed. A rotary switch operates with a twisting motion of the operating handle with at least two positions. One or more positions of

16206-432: The pickup selector in position 2; similarly the middle and neck pickups in parallel can be obtained in position 4. This setting's characteristic tone is not caused by any electronic phenomenon—early Stratocasters used identical pickups for all positions. This "in between" tone is caused by phase cancellation due to the physical position of the pickups along the vibrating string. The neck and middle pickups are each wired to

16352-423: The pickups do not produce a signal directly from the vibration of the strings, but rather from the vibration of the guitar top or body, and the amplification of the sound merely increases volume, not alters tone. Electric guitar design and construction vary greatly in the shape of the body and the configuration of the neck, bridge, and pickups. However, some features are present on most guitars. The photo below shows

16498-426: The pitch of the notes being played. Hank Marvin , Jeff Beck and Ike Turner have used the Stratocaster's floating vibrato extensively in their playing. As string gauges have changed, players have experimented with the number of springs (often four though Hendrix used five). As the average gauge has decreased over the years, modern Stratocasters are equipped with three springs as a stock option in order to counteract

16644-414: The player. Fender has released numerous models with different pickup configurations and has made other small modifications to the electronics and components of the base model, such as changing the initial 3-position selector switch to a standard 5-position selector switch, offering more tonal variety, as well as other small cosmetic changes to things like tuning pegs and types of woods used in various parts of

16790-553: The position of a machine part, liquid level, pressure, or temperature, such as a thermostat . Many specialized forms exist, such as the toggle switch , rotary switch , mercury switch , push-button switch, reversing switch , relay , and circuit breaker . A common use is control of lighting, where multiple switches may be wired into one circuit to allow convenient control of light fixtures. Switches in high-powered circuits must have special construction to prevent destructive arcing when they are opened. The most familiar form of switch

16936-424: The power being switched is sufficiently large, the electron flow across opening switch contacts is sufficient to ionize the air molecules across the tiny gap between the contacts as the switch is opened, forming a gas plasma , also known as an electric arc . The plasma is of low resistance and is able to sustain power flow, even with the separation distance between the switch contacts steadily increasing. The plasma

17082-414: The recessed jack plate, facilitating assembly. The 1963 Fender Stratocaster shows an advancement in design from the 1950s models including a 'veneer' Brazilian rosewood board with Clay Dot inlays, a 3 tone sunburst finish on an Alder body and Kluson tuners. To summarize, the specific features in the evolution of the Fender Stratocaster between 1954 and 1979 included: Despite being credited with inventing

17228-416: The reduced string tension. While the floating bridge has unique advantages for wavering pitch upwards (like Jeff Beck), the functionality of the "floating" has been widely accepted, yet disputed by some musicians. Leo Fender insisted it leave the factory floating (raised up in the back) while designer Freddie Tavares preferred it tightened flush for full bridge plate/body contact resonance. As the bridge floats,

17374-482: The result of roughness and oxide films, they exhibit contact resistance , limits on the current and voltage they can handle, finite switching time, etc. The ideal switch is often used in circuit analysis as it greatly simplifies the system of equations to be solved, but this can lead to a less accurate solution. Theoretical treatment of the effects of non-ideal properties is required in the design of large networks of switches, as for example used in telephone exchanges. In

17520-592: The rising cost of rare tonewoods , human-made materials may be economically preferable and more ecologically sensitive. However, wood remains popular in production instruments, though sometimes in conjunction with new materials. Vigier guitars , for example, use a wooden neck reinforced by embedding a light, carbon fiber rod in place of the usual heavier steel bar or adjustable steel truss rod. After-market necks made entirely from carbon fiber fit existing bolt-on instruments. Few, if any, extensive formal investigations have been widely published that confirm or refute claims over

17666-581: The same time by one handle. The parts may be mounted on an insulating base with terminals for wiring, or may be directly bolted to an insulated switch board in a large assembly. Since the electrical contacts are exposed, the switch is used only where people cannot accidentally come in contact with the switch or where the voltage is so low as to not present a hazard. Knife switches are made in many sizes from miniature switches to large devices used to carry thousands of amperes. In electrical transmission and distribution, gang-operated switches are used in circuits up to

17812-453: The shoulder with a strap. The three- pickup design offered players increased versatility and choice in tone quality over earlier one- and two-pickup electric guitars, and a responsive and simplified vibrato arm integrated into the bridge plate, which marked a significant design improvement over other vibrato systems, such as those manufactured by Bigsby . All of these design elements were popularized and later became an industry standard due to

17958-636: The simplest case, a switch has two conductive pieces, often metal , called contacts , connected to an external circuit, that touch to complete (make) the circuit, and separate to open (break) the circuit. The contact material is chosen for its resistance to corrosion, because most metals form insulating oxides that would prevent the switch from working. Contact materials are also chosen on the basis of electrical conductivity , hardness (resistance to abrasive wear), mechanical strength, low cost and low toxicity. The formation of oxide layers at contact surface, as well as surface roughness and contact pressure, determine

18104-449: The simultaneous actuation of multiple sets of electrical contacts , or the control of large amounts of electric current or mains voltages. The word "toggle" is a reference to a kind of mechanism or joint consisting of two arms, which are almost in line with each other, connected with an elbow-like pivot. However, the phrase "toggle switch" is applied to a switch with a short handle and a positive snap-action, whether it actually contains

18250-437: The speed at which the switch control is operated by the user. Movement of the switch control lever applies tension to a spring until a tipping point is reached, and the contacts suddenly snap open or closed as the spring tension is released. As the power being switched increases, other methods are used to minimize or prevent arc formation. A plasma is hot and will rise due to convection air currents. The arc can be quenched with

18396-538: The strings at or directly behind the bridge and is fastened securely to the top of the instrument. These are common on carved-top guitars, such as the Gibson Les Paul and the Paul Reed Smith models , and on slab-body guitars, such as the Music Man Albert Lee and Fender guitars that are not equipped with a vibrato arm. A floating or trapeze tailpiece (similar to a violin 's) fastens to

18542-461: The strings from nut to bridge. A typical Fender guitar uses a 25.5-inch (65 cm) scale length, while Gibson uses a 24.75-inch (62.9 cm) scale length in their Les Paul . While the scale length of the Les Paul is often described as 24.75 inches, it has varied through the years by as much as a half inch. Frets are positioned proportionally to scale length—the shorter the scale length,

18688-615: The strings to alter the pitch . A player can use this to create a vibrato or a portamento effect. Early vibrato systems were often unreliable and made the guitar go out of tune easily. They also had a limited pitch range. Later Fender designs were better, but Fender held the patent on these, so other companies used older designs for many years. With the expiration of the Fender patent on the Stratocaster -style vibrato, various improvements on this type of internal, multi-spring vibrato system are now available. Floyd Rose introduced one of

18834-399: The success of the Stratocaster. The Fender Stratocaster is one of the most iconic electric guitar models of all time. Over the years, countless variations of the Stratocaster have been made. The modular nature of the guitar, with its easily removable components, left players and luthiers to perform numerous modifications to their own guitars, changing out pickups or necks to fit the needs of

18980-413: The switch action. A switch with both types of contact is called a changeover switch or double-throw switch . These may be " make-before-break " (" MBB " or shorting) which momentarily connects both circuits, or may be " break-before-make " (" BBM " or non-shorting) which interrupts one circuit before closing the other. These terms have given rise to abbreviations for the types of switch which are used in

19126-415: The switch may be momentary (biased with a spring), requiring the operator to hold the switch in the position. Other positions may have a detent to hold the position when released. A rotary switch may have multiple levels or "decks" in order to allow it to control multiple circuits. One form of rotary switch consists of a spindle or "rotor" that has a contact arm or "spoke" which projects from its surface like

19272-451: The terms two way and three way are used with different meanings). Form A Switches with larger numbers of poles or throws can be described by replacing the "S" or "D" with a number (e.g. 3PST, SP4T, etc.) or in some cases the letter "T" (for "triple") or "Q" (for "quadruple"). In the rest of this article the terms SPST , SPDT and intermediate will be used to avoid the ambiguity. Contact bounce (also called chatter )

19418-592: The time, the Electro-Spanish Ken Roberts was designed to play while standing upright with the guitar on a strap, as with acoustic guitars. The Electro-Spanish Ken Roberts was also the first instrument to feature a hand-operated vibrato as a standard arrangement, a device called the "Vibrola", invented by Doc Kauffman . It is estimated that fewer than 50 Electro-Spanish Ken Roberts were constructed between 1933 and 1937; fewer than 10 are known to survive today. The solid-body electric guitar

19564-420: The transitional state of the switch as well as the ability to withstand continuous operating currents must be considered. When a switch is in the on state, its resistance is near zero and very little power is dropped in the contacts; when a switch is in the off state, its resistance is extremely high and even less power is dropped in the contacts. However, when the switch is flicked, the resistance must pass through

19710-407: The turning of a key ( key switch ), linear or rotary movement (a limit switch or microswitch ), or presence of a magnetic field (the reed switch ). Many switches are operated automatically by changes in some environmental condition or by motion of machinery. A limit switch is used, for example, in machine tools to interlock operation with the proper position of tools. In heating or cooling systems

19856-693: The vibrations of the guitar strings into electrical signals, which could then be amplified. Commercial production began in late summer of 1932 by the Ro-Pat-In Corporation (Elect ro - Pat ent- In strument Company), in Los Angeles, a partnership of Beauchamp, Adolph Rickenbacker (originally Rickenbacher), and Paul Barth. In 1934, the company was renamed the Rickenbacker Electro Stringed Instrument Company. In that year Beauchamp applied for

20002-466: The voltage potential is sufficient to exceed the breakdown voltage of the air separating the contacts, an arc forms which is sustained until the switch closes completely and the switch surfaces make contact. In either case, the standard method for minimizing arc formation and preventing contact damage is to use a fast-moving switch mechanism, typically using a spring-operated tipping-point mechanism to assure quick motion of switch contacts, regardless of

20148-505: Was a cast aluminium lap steel guitar nicknamed the "Frying Pan" designed in 1931 by George Beauchamp , the general manager of the National Stringed Instrument Corporation , with Paul Barth, who was vice president. George Beauchamp, along with Adolph Rickenbacker , invented the electromagnetic pickups. Coils that were wrapped around a magnet would create an electromagnetic field that converted

20294-479: Was designed by Walt Fuller. It became known as the " Charlie Christian " pickup (named for the jazz guitarist who was among the first to perform with the ES-150 guitar). The ES-150 achieved some popularity but suffered from unequal loudness across the six strings. A functioning solid-body electric guitar was designed and built in 1940 by Les Paul from an Epiphone acoustic archtop as an experiment. His " log guitar " —

20440-631: Was discontinued in 2008. The Custom Classic Strat was intended to be a combination of the best aspects of vintage and modern Strats. The guitar boasted 3 Modern Classic pickups along with a Custom Classic 2-point tremolo with pop-in tremolo bar. The "C" Shaped neck was maple with either maple or rosewood finger board and 22 jumbo frets. The colors available were three-color sunburst, daphne blue, black, bing cherry transparent, cobalt blue transparent, and honey blonde. Fender has released several models of Stratocaster in collaboration with famous guitarists. They include: Electric guitar An electric guitar

20586-509: Was discontinued in 2012. As well as the vintage reissues, Fender launched an updated model in 1987: the American Standard Stratocaster. This was tailored to the demands of modern players, notably having a flatter fingerboard, a thinner neck profile and an improved tremolo system. This model line has been continuously improved and remained in production until late 2016. The model line received upgrades in 2000, when it

20732-417: Was originally a two-color, dark brown-to-golden yellow sunburst pattern, although custom color guitars were produced (An example is Eldon Shamblin 's gold Stratocaster, dated June 1954). In 1956, Fender began using alder for sunburst and most custom-color Stratocaster bodies. Ash needed grain filler and sanding blocks for contour sanding, though it was still used on translucent blonde instruments. In 1957,

20878-685: Was renamed as the American Series Stratocaster, and again in 2008, when the American Standard name was restored. In 2017, the American Standard Stratocaster was replaced by the American Professional Stratocaster, with narrow frets, a fatter 'deep C' neck profile and V-Mod pickups. Various other modern American-made Stratocasters have been produced. As of 2019, these include the more affordable American Performer Stratocaster (successor to

21024-743: Was the Ibanez Jem (1987) which featured "24 frets", an impossibly thin neck" and was "designed to be the ultimate shredder machine". Numerous other important electric guitars are on the list, including Gibson ES-150 (1936), Fender Telecaster (1951), Gibson Les Paul (1952), Gretsch 6128 Duo Jet (1953), Fender Stratocaster (1954), Rickenbacker 360/12 (1964), Van Halen Frankenstrat (1975), Paul Reed Smith Custom (1985) many of these guitars were "successors" to earlier designs. Electric guitar designs eventually became culturally important and visually iconic, with various model companies selling miniature model versions of particularly famous electric guitars, for example,

21170-531: Was the '57 American Vintage Reissue. The company regarded 1957 as a benchmark year for the Strat. The original specifications were used, with three 57/62 pickups, aged pickup covers and knobs, a tinted 7.25" radius, 21 fret maple neck, an ashtray bridge cover, and three position switch (with five-position switch kit included). The colors included white blonde, two-color sunburst, black, ocean turquoise, surf green, and ice blue metallic. The '57 Vintage Reissue Stratocaster

21316-553: Was unable to sell the idea behind his "App" guitar to either company. In 1946, Merle Travis commissioned steel guitar builder Paul Bigsby to build him a solid-body Spanish-style electric. Bigsby delivered the guitar in 1948. The first mass-produced solid-body guitar was Fender Esquire and Fender Broadcaster (later to become the Fender Telecaster ), first made in 1950, five years after Les Paul made his prototype . The Gibson Les Paul appeared soon after to compete with

#669330