Misplaced Pages

#876123

78-458: PTOL indicates that there is no requirement for a runway for operations (IE: Point-defence ). Instead, ‘point’ suggests that the length of runway required is near zero, implying a minimal-sized location for touchdown and takeoff. Sometimes no prepared surface at all is needed. PTOL is assisted in certain cases by means which are not needed by vertical take-off and landing (VTOL) or by short take-off and landing (STOL) vehicles. These may include

156-513: A parachute drop zone . The gliders were treated as disposable, constructed from inexpensive materials such as wood, though a few were re-used. By the time of the Korean War , transport aircraft had become larger and more efficient so that even light tanks could be dropped by parachute, obsoleting gliders. Even after the development of powered aircraft, gliders continued to be used for aviation research . The NASA Paresev Rogallo flexible wing

234-460: A pilot , but some are unmanned and controlled either remotely or autonomously. Kites were used approximately 2,800 years ago in China, where kite building materials were available. Leaf kites may have been flown earlier in what is now Sulawesi , based on their interpretation of cave paintings on nearby Muna Island . By at least 549 AD paper kites were flying, as recorded that year, a paper kite

312-411: A windsock beside a landing strip. Types of runway safety incidents include: The choice of material used to construct the runway depends on the use and the local ground conditions. For a major airport, where the ground conditions permit, the most satisfactory type of pavement for long-term minimum maintenance is concrete . Although certain airports have used reinforcement in concrete pavements, this

390-480: A 7 will indicate 7,000 ft (2,134 m) remaining. The runway threshold is marked by a line of green lights. [REDACTED] There are three types of runways: Waterways may be unmarked or marked with buoys that follow maritime notation instead. For runways and taxiways that are permanently closed, the lighting circuits are disconnected. The runway threshold, runway designation, and touchdown markings are obliterated and yellow "Xs" are placed at each end of

468-679: A Vickers Vimy in 1919 , followed months later by the U.S. Navy's NC-4 transatlantic flight ; culminating in May 1927 with Charles Lindbergh 's solo trans-Atlantic flight in the Spirit of St. Louis spurring ever-longer flight attempts. Airplanes had a presence in the major battles of World War II. They were an essential component of military strategies, such as the German Blitzkrieg or the American and Japanese aircraft carrier campaigns of

546-416: A glider) made out of paper or paperboard. Model glider aircraft are models of aircraft using lightweight materials such as polystyrene and balsa wood . Designs range from simple glider aircraft to accurate scale models , some of which can be very large. Glide bombs are bombs with aerodynamic surfaces to allow a gliding flight path rather than a ballistic one. This enables stand-off aircraft to attack

624-400: A glider. Gliders and sailplanes that are used for the sport of gliding have high aerodynamic efficiency. The highest lift-to-drag ratio is 70:1, though 50:1 is common. After take-off, further altitude can be gained through the skillful exploitation of rising air. Flights of thousands of kilometers at average speeds over 200 km/h have been achieved. One small-scale example of a glider

702-486: A landing site for the Space Shuttle . Takeoff and landing distances available are given using one of the following terms: There are standards for runway markings. There are runway markings and signs on most large runways. Larger runways have a distance remaining sign (black box with white numbers). This sign uses a single number to indicate the remaining distance of the runway in thousands of feet. For example,

780-526: A limited propulsion system for takeoff, or to extend flight duration. As is the case with planes, gliders come in diverse forms with varied wings, aerodynamic efficiency, pilot location, and controls. Large gliders are most commonly born aloft by a tow-plane or by a winch . Military gliders have been used in combat to deliver troops and equipment, while specialized gliders have been used in atmospheric and aerodynamic research. Rocket-powered aircraft and spaceplanes have made unpowered landings similar to

858-542: A periodic basis. Fields with very low traffic of light planes may use a sod surface. Some runways make use of salt flats. For pavement designs, borings are taken to determine the subgrade condition, and based on the relative bearing capacity of the subgrade, the specifications are established. For heavy-duty commercial aircraft, the pavement thickness, no matter what the top surface, varies from 10 to 48 in (25 to 122 cm), including subgrade. Airport pavements have been designed by two methods. The first, Westergaard ,

SECTION 10

#1732787302877

936-635: A streamlined fuselage and long narrow wings incorporating a high aspect ratio . Single-seat and two-seat gliders are available. Initially, training was done by short "hops" in primary gliders , which have no cockpit and minimal instruments. Since shortly after World War II, training is done in two-seat dual control gliders, but high-performance two-seaters can make long flights. Originally skids were used for landing, later replaced by wheels, often retractable. Gliders known as motor gliders are designed for unpowered flight, but can deploy piston , rotary , jet or electric engines . Gliders are classified by

1014-465: A successful passenger-carrying glider in 1853. In 1856, Frenchman Jean-Marie Le Bris made the first powered flight, had his glider L'Albatros artificiel towed by a horse along a beach. In 1884, American John J. Montgomery made controlled flights in a glider as a part of a series of gliders he built between 1883 and 1886. Other aviators who made similar flights at that time were Otto Lilienthal , Percy Pilcher , and protégés of Octave Chanute . In

1092-460: A surface winch (on a ship or on the ground) and the winch pulls the UAV down to the intended ‘point’. This is potentially useful for land and naval usage of fixed-wing UAVs. Patent 4,790,497 "Point-landing method for non vertical take off and landing flying objects" Patent 4,753,400 "Shipboard air vehicle retrieval apparatus" Patent 4,311,290 "Arrestment system" Runway According to

1170-452: A target from a distance. A kite is a tethered aircraft held aloft by wind that blows over its wing(s). High pressure below the wing deflects the airflow downwards. This deflection generates horizontal drag in the direction of the wind. The resultant force vector from the lift and drag force components is opposed by the tension of the tether . Kites are mostly flown for recreational purposes, but have many other uses. Early pioneers such as

1248-415: A third parallel runway was opened at Phoenix Sky Harbor International Airport in 2000 to the south of existing 8R/26L—rather than confusingly becoming the "new" 8R/26L it was instead designated 7R/25L, with the former 8R/26L becoming 7L/25R and 8L/26R becoming 8/26. Suffixes may also be used to denote special use runways. Airports that have seaplane waterways may choose to denote the waterway on charts with

1326-404: A tube, or an UAV launched by a rail-launcher or similar means, is in effect making a point takeoff. For the landings, several ideas have been proposed. An example for sea operations is catching a UAV in a parachute in the air behind a ship, then lowering the UAV to the deck by pulling the parachute in. Another idea is 'cable-assisted PTOL' for fixed-wing UAVs. The UAV makes a cable connection to

1404-441: A very long cable enforcing the convergence of the aircraft from afar onto the intended touchdown point. This may still be worthwhile due to maintaining the air-vehicle's advantages which are maximal simplicity leading to better cruise performance, as is the case using a fixed-wing UAV platform. PTOL capability enables UAVs and aircraft to land and take off in very confined locations like rooftops, ship decks and forest clearings. This

1482-404: Is a lightweight, free-flying, foot-launched glider with no rigid body. The pilot is suspended in a harness below a hollow fabric wing whose shape is formed by its suspension lines. Air entering vents in the front of the wing and the aerodynamic forces of the air flowing over the outside power the craft. Paragliding is most often a recreational activity. A paper plane is a toy aircraft (usually

1560-445: Is an extrapolation of the original test results, which are not applicable to modern aircraft pavements or to modern aircraft landing gear . Some designs were made by a mixture of these two design theories. A more recent method is an analytical system based on the introduction of vehicle response as an important design parameter. Essentially it takes into account all factors, including the traffic conditions, service life, materials used in

1638-469: Is based on the assumption that the pavement is an elastic plate supported on a heavy fluid base with a uniform reaction coefficient known as the K value . Experience has shown that the K values on which the formula was developed are not applicable for newer aircraft with very large footprint pressures. The second method is called the California bearing ratio and was developed in the late 1940s. It

SECTION 20

#1732787302877

1716-767: Is capable of flight using aerodynamic lift . Fixed-wing aircraft are distinct from rotary-wing aircraft (in which a rotor mounted on a spinning shaft generates lift), and ornithopters (in which the wings oscillate to generate lift). The wings of a fixed-wing aircraft are not necessarily rigid; kites, hang gliders , variable-sweep wing aircraft, and airplanes that use wing morphing are all classified as fixed wing. Gliding fixed-wing aircraft, including free-flying gliders and tethered kites , can use moving air to gain altitude. Powered fixed-wing aircraft (airplanes) that gain forward thrust from an engine include powered paragliders , powered hang gliders and ground effect vehicles . Most fixed-wing aircraft are operated by

1794-408: Is capable of taking off and landing (alighting) on water. Seaplanes that can also operate from dry land are a subclass called amphibian aircraft . Seaplanes and amphibians divide into two categories: float planes and flying boats . Many forms of glider may include a small power plant. These include: A ground effect vehicle (GEV) flies close to the terrain, making use of the ground effect –

1872-436: Is comparable to VTOL, but it helps fixed-wing/simple UAVs achieve this, avoiding the complexity and cost of air-vehicle construction required for VTOL which include jet-thrust-rotation engines , engine pods or rotor tilting mechanisms. This gives higher aerodynamic efficiency and allows smaller engines and lower cost, among other advantages. Also, a true PTOL solution means exact touchdowns even in adverse conditions such as

1950-399: Is considered to have the longest takeoff distance of the more common aircraft types and has set the standard for runway lengths of larger international airports. At sea level , 3,200 m (10,500 ft) can be considered an adequate length to land virtually any aircraft. For example, at O'Hare International Airport , when landing simultaneously on 4L/22R and 10/28 or parallel 9R/27L, it

2028-418: Is generally found to be unnecessary, with the exception of expansion joints across the runway where a dowel assembly, which permits relative movement of the concrete slabs, is placed in the concrete. Where it can be anticipated that major settlements of the runway will occur over the years because of unstable ground conditions, it is preferable to install asphalt concrete surface, as it is easier to patch on

2106-408: Is included for all ICAO and some U.S. military airports (such as Edwards Air Force Base ). However, most U.S.  civil aviation airports drop the leading zero as required by FAA regulation. This also includes some military airfields such as Cairns Army Airfield . This American anomaly may lead to inconsistencies in conversations between American pilots and controllers in other countries. It

2184-454: Is most nearly aligned with the wind. Airports with one runway are often constructed to be aligned with the prevailing wind . Compiling a wind rose is one of the preliminary steps taken in constructing airport runways. Wind direction is given as the direction the wind is coming from : a plane taking off from runway 09 faces east, into an "east wind" blowing from 090°. Originally in the 1920s and 1930s, airports and air bases (particularly in

2262-578: Is routine for arrivals from East Asia , which would normally be vectored for 4L/22R (2,300 m (7,546 ft)) or 9R/27L (2,400 m (7,874 ft)) to request 28R (4,000 m (13,123 ft)). It is always accommodated, although occasionally with a delay. Another example is that the Luleå Airport in Sweden was extended to 3,500 m (11,483 ft) to allow any fully loaded freight aircraft to take off. These distances are also influenced by

2340-451: Is slow, runway designation changes are uncommon, and not welcomed, as they require an accompanying change in aeronautical charts and descriptive documents. When a runway designation does change, especially at major airports, it is often done at night, because taxiway signs need to be changed and the numbers at each end of the runway need to be repainted to the new runway designators. In July 2009 for example, London Stansted Airport in

2418-526: Is sport and recreation. Gliders were developed in the 1920s for recreational purposes. As pilots began to understand how to use rising air, sailplane gliders were developed with a high lift-to-drag ratio . These allowed the craft to glide to the next source of " lift ", increasing their range. This gave rise to the popular sport of gliding . Early gliders were built mainly of wood and metal, later replaced by composite materials incorporating glass, carbon or aramid fibers. To minimize drag , these types have

PTOL - Misplaced Pages Continue

2496-649: Is the paper airplane. An ordinary sheet of paper can be folded into an aerodynamic shape fairly easily; its low mass relative to its surface area reduces the required lift for flight, allowing it to glide some distance. Gliders and sailplanes share many design elements and aerodynamic principles with powered aircraft. For example, the Horten H.IV was a tailless flying wing glider, and the delta-winged Space Shuttle orbiter glided during its descent phase. Many gliders adopt similar control surfaces and instruments as airplanes. The main application of modern glider aircraft

2574-459: Is usually adequate for aircraft weights below approximately 100,000 kg (220,000 lb). Larger aircraft including widebodies will usually require at least 2,400 m (7,900 ft) at sea level. International widebody flights, which carry substantial amounts of fuel and are therefore heavier, may also have landing requirements of 3,200 m (10,500 ft) or more and takeoff requirements of 4,000 m (13,000 ft). The Boeing 747

2652-557: Is very common in a country such as Canada for a controller to clear an incoming American aircraft to, for example, runway 04, and the pilot read back the clearance as runway 4. In flight simulation programs those of American origin might apply U.S. usage to airports around the world. For example, runway 05 at Halifax will appear on the program as the single digit 5 rather than 05. Military airbases may include smaller paved runways known as "assault strips" for practice and training next to larger primary runways. These strips eschew

2730-550: The FAI for competitions into glider competition classes mainly on the basis of wingspan and flaps. A class of ultralight sailplanes, including some known as microlift gliders and some known as airchairs, has been defined by the FAI based on weight. They are light enough to be transported easily, and can be flown without licensing in some countries. Ultralight gliders have performance similar to hang gliders , but offer some crash safety as

2808-598: The International Civil Aviation Organization (ICAO), a runway is a "defined rectangular area on a land aerodrome prepared for the landing and takeoff of aircraft ". Runways may be a human-made surface (often asphalt , concrete , or a mixture of both) or a natural surface ( grass , dirt , gravel , ice , sand or salt ). Runways, taxiways and ramps , are sometimes referred to as "tarmac", though very few runways are built using tarmac . Takeoff and landing areas defined on

2886-534: The Wright Flyer III was capable of fully controllable, stable flight for substantial periods. In 1906, Brazilian inventor Alberto Santos Dumont designed, built and piloted an aircraft that set the first world record recognized by the Aéro-Club de France by flying the 14 bis 220 metres (720 ft) in less than 22 seconds. The flight was certified by the FAI. The Bleriot VIII design of 1908

2964-455: The 1890s, Lawrence Hargrave conducted research on wing structures and developed a box kite that lifted the weight of a man. His designs were widely adopted. He also developed a type of rotary aircraft engine, but did not create a powered fixed-wing aircraft. Sir Hiram Maxim built a craft that weighed 3.5 tons, with a 110-foot (34-meter) wingspan powered by two 360-horsepower (270-kW) steam engines driving two propellers. In 1894, his machine

3042-466: The 18th and 19th centuries kites were used for scientific research. Around 400 BC in Greece , Archytas was reputed to have designed and built the first self-propelled flying device, shaped like a bird and propelled by a jet of what was probably steam, said to have flown some 200 m (660 ft). This machine may have been suspended during its flight. One of the earliest attempts with gliders

3120-540: The Pacific. Military gliders were developed and used in several campaigns, but were limited by the high casualty rate encountered. The Focke-Achgelis Fa 330 Bachstelze (Wagtail) rotor kite of 1942 was notable for its use by German U-boats . Before and during the war, British and German designers worked on jet engines . The first jet aircraft to fly, in 1939, was the German Heinkel He 178 . In 1943,

3198-659: The United Kingdom changed its runway designations from 05/23 to 04/22 during the night. Runway dimensions vary from as small as 245 m (804 ft) long and 8 m (26 ft) wide in smaller general aviation airports, to 5,500 m (18,045 ft) long and 80 m (262 ft) wide at large international airports built to accommodate the largest jets , to the huge 11,917 m × 274 m (39,098 ft × 899 ft) lake bed runway 17/35 at Edwards Air Force Base in California – developed as

PTOL - Misplaced Pages Continue

3276-468: The United Kingdom) were built in a triangle-like pattern of three runways at 60° angles to each other. The reason was that aviation was only starting, and although it was known that wind affected the runway distance required, not much was known about wind behaviour. As a result, three runways in a triangle-like pattern were built, and the runway with the heaviest traffic would eventually expand into

3354-569: The United States and Canada in 1919. The so-called Golden Age of Aviation occurred between the two World Wars, during which updated interpretations of earlier breakthroughs. Innovations include Hugo Junkers ' all-metal air frames in 1915 leading to multi-engine aircraft of up to 60+ meter wingspan sizes by the early 1930s, adoption of the mostly air-cooled radial engine as a practical aircraft power plant alongside V-12 liquid-cooled aviation engines, and longer and longer flights – as with

3432-420: The adjustments required for a given temperature. In India, recommendations of International Civil Aviation Organization (ICAO) are now followed more often. For landing, only altitude correction is done for runway length whereas for take-off, all types of correction are taken into consideration. Fixed-wing aircraft A fixed-wing aircraft is a heavier-than-air aircraft , such as an airplane , which

3510-559: The aircraft tyres. To maintain the macrotexturing built into the runway by the grooves, maintenance crews engage in airfield rubber removal or hydrocleaning in order to meet required FAA , or other aviation authority friction levels. Subsurface underdrains help provide extended life and excellent and reliable pavement performance. At the Hartsfield Atlanta, GA airport the underdrains usually consist of trenches 18 in (46 cm) wide and 48 in (120 cm) deep from

3588-447: The airport's main runway, while the other two runways would be either abandoned or converted into taxiways. Runways are named by a number between 01 and 36, which is generally the magnetic azimuth of the runway's heading in deca degrees . This heading differs from true north by the local magnetic declination . A runway numbered 09 points east (90°), runway 18 is south (180°), runway 27 points west (270°) and runway 36 points to

3666-543: The ambiguity that would result with more than three parallel runways. For example, in Los Angeles, this system results in runways 6L, 6R, 7L, and 7R, even though all four runways are actually parallel at approximately 69°. At Dallas/Fort Worth International Airport , there are five parallel runways, named 17L, 17C, 17R, 18L, and 18R, all oriented at a heading of 175.4°. Occasionally, an airport with only three parallel runways may use different runway identifiers, such as when

3744-411: The construction, and, especially important, the dynamic response of the vehicles using the landing area. Because airport pavement construction is so expensive, manufacturers aim to minimize aircraft stresses on the pavement. Manufacturers of the larger planes design landing gear so that the weight of the plane is supported on larger and more numerous tires. Attention is also paid to the characteristics of

3822-729: The first operational jet fighter, the Messerschmitt Me 262 , went into service with the German Luftwaffe . Later in the war the British Gloster Meteor entered service, but never saw action – top air speeds for that era went as high as 1,130 km/h (700 mph), with the early July 1944 unofficial record flight of the German Me 163B V18 rocket fighter prototype. In October 1947, the Bell X-1

3900-575: The following: According to Transport Canada 's regulations, the runway-edge lighting must be visible for at least 2 mi (3 km). Additionally, a new system of advisory lighting, runway status lights , is currently being tested in the United States. The edge lights must be arranged such that: Typically the lights are controlled by a control tower , a flight service station or another designated authority. Some airports/airfields (particularly uncontrolled ones ) are equipped with pilot-controlled lighting , so that pilots can temporarily turn on

3978-559: The interaction between the wings and the surface. Some GEVs are able to fly higher out of ground effect (OGE) when required – these are classed as powered fixed-wing aircraft. A glider is a heavier-than-air craft whose free flight does not require an engine. A sailplane is a fixed-wing glider designed for soaring – gaining height using updrafts of air and to fly for long periods. Gliders are mainly used for recreation but have found use for purposes such as aerodynamics research, warfare and spacecraft recovery. Motor gliders are equipped with

SECTION 50

#1732787302877

4056-496: The lack of designated landing direction. If there is more than one runway pointing in the same direction (parallel runways), each runway is identified by appending left (L), center (C) and right (R) to the end of the runway number to identify its position (when facing its direction)—for example, runways one-five-left (15L), one-five-center (15C), and one-five-right (15R). Runway zero-three-left (03L) becomes runway two-one-right (21R) when used in

4134-432: The landing gear itself, so that adverse effects on the pavement are minimized. Sometimes it is possible to reinforce a pavement for higher loading by applying an overlay of asphaltic concrete or portland cement concrete that is bonded to the original slab. Post-tensioning concrete has been developed for the runway surface. This permits the use of thinner pavements and should result in longer concrete pavement life. Because of

4212-409: The lights when the relevant authority is not available. This avoids the need for automatic systems or staff to turn the lights on at night or in other low visibility situations. This also avoids the cost of having the lighting system on for extended periods. Smaller airports may not have lighted runways or runway markings. Particularly at private airfields for light planes, there may be nothing more than

4290-458: The nearest 10°, this affects some runways sooner than others. For example, if the magnetic heading of a runway is 233°, it is designated Runway 23. If the magnetic heading changes downwards by 5 degrees to 228°, the runway remains Runway 23. If on the other hand the original magnetic heading was 226° (Runway 23), and the heading decreased by only 2 degrees to 224°, the runway becomes Runway 22. Because magnetic drift itself

4368-521: The need for "distinctly marked and carefully prepared landing places, [but] the preparing of the surface of reasonably flat ground [is] an expensive undertaking [and] there would also be a continuous expense for the upkeep." For fixed-wing aircraft , it is advantageous to perform takeoffs and landings into the wind to reduce takeoff or landing roll and reduce the ground speed needed to attain flying speed . Larger airports usually have several runways in different directions, so that one can be selected that

4446-581: The north (360° rather than 0°). When taking off from or landing on runway 09, a plane is heading around 90° (east). A runway can normally be used in both directions, and is named for each direction separately: e.g., "runway 15" in one direction is "runway 33" when used in the other. The two numbers differ by 18 (= 180°). For clarity in radio communications, each digit in the runway name is pronounced individually: runway one-five, runway three-three, etc. (instead of "fifteen" or "thirty-three"). A leading zero, for example in "runway zero-six" or "runway zero-one-left",

4524-589: The opposite direction (derived from adding 18 to the original number for the 180° difference when approaching from the opposite direction). In some countries, regulations mandate that where parallel runways are too close to each other, only one may be used at a time under certain conditions (usually adverse weather ). At large airports with four or more parallel runways (for example, at Chicago O'Hare , Los Angeles , Detroit Metropolitan Wayne County , Hartsfield-Jackson Atlanta , Denver , Dallas–Fort Worth and Orlando ), some runway identifiers are shifted by 1 to avoid

4602-693: The pilot can strap into an upright seat within a deform-able structure. Landing is usually on one or two wheels which distinguishes these craft from hang gliders. Most are built by individual designers and hobbyists. Military gliders were used during World War II for carrying troops ( glider infantry ) and heavy equipment to combat zones. The gliders were towed into the air and most of the way to their target by transport planes, e.g. C-47 Dakota , or by one-time bombers that had been relegated to secondary activities, e.g. Short Stirling . The advantage over paratroopers were that heavy equipment could be landed and that troops were quickly assembled rather than dispersed over

4680-414: The pilot is suspended in a harness suspended from the air frame , and exercises control by shifting body weight in opposition to a control frame. Hang gliders are typically made of an aluminum alloy or composite -framed fabric wing. Pilots can soar for hours, gain thousands of meters of altitude in thermal updrafts, perform aerobatics, and glide cross-country for hundreds of kilometers. A paraglider

4758-483: The rolling and heaving deck of a ship, strong winds on land, or nearby obstacles such as trees or rocks. The ability to land a UAV direct onto a vehicle, with cushioning, adds safety to deployed UAVs, providing touchdown with no-runway or pre-prepared area and easing a quick change of the landing-site. The fact that PTOL capable UAVs can land unassisted on rolling ships gives them an advantage over manned helicopters. PTOL takeoffs are quite simple. Any rocket launched from

SECTION 60

#1732787302877

4836-478: The runway grade (slope) such that, for example, each 1 percent of runway down slope increases the landing distance by 10 percent. An aircraft taking off at a higher altitude must do so at reduced weight due to decreased density of air at higher altitudes, which reduces engine power and wing lift. An aircraft must also take off at a reduced weight in hotter or more humid conditions (see density altitude ). Most commercial aircraft carry manufacturer's tables showing

4914-406: The runway and at 1,000 ft (305 m) intervals. A line of lights on an airfield or elsewhere to guide aircraft in taking off or coming in to land or an illuminated runway is sometimes also known as a flare path . Runway lighting is used at airports during periods of darkness and low visibility. Seen from the air, runway lights form an outline of the runway. A runway may have some or all of

4992-623: The standard numerical naming convention and instead employ the runway's full three digit heading; examples include Dobbins Air Reserve Base 's Runway 110/290 and Duke Field 's Runway 180/360. Runways with non-hard surfaces, such as small turf airfields and waterways for seaplanes , may use the standard numerical scheme or may use traditional compass point naming, examples include Ketchikan Harbor Seaplane Base 's Waterway E/W. Airports with unpredictable or chaotic water currents, such as Santa Catalina Island 's Pebbly Beach Seaplane Base, may designate their landing area as Waterway ALL/WAY to denote

5070-414: The suffix T; this is advantageous for certain airfields in the far north such as Thule Air Base (08T/26T). Runway designations may change over time because Earth's magnetic lines slowly drift on the surface and the magnetic direction changes. Depending on the airport location and how much drift occurs, it may be necessary to change the runway designation. As runways are designated with headings rounded to

5148-577: The suffix W; such as Daniel K. Inouye International Airport in Honolulu and Lake Hood Seaplane Base in Anchorage . Small airports that host various forms of air traffic may employ additional suffixes to denote special runway types based on the type of aircraft expected to use them, including STOL aircraft (S), gliders (G), rotorcraft (H), and ultralights (U). Runways that are numbered relative to true north rather than magnetic north will use

5226-652: The surface of water for seaplanes are generally referred to as waterways . Runway lengths are now commonly given in meters worldwide , except in North America where feet are commonly used. In 1916, in a World War I war effort context, the first concrete-paved runway was built in Clermont-Ferrand in France , allowing local company Michelin to manufacture Bréguet Aviation military aircraft. In January 1919, aviation pioneer Orville Wright underlined

5304-441: The susceptibility of thinner pavements to frost heave , this process is generally applicable only where there is no appreciable frost action . Runway pavement surface is prepared and maintained to maximize friction for wheel braking. To minimize hydroplaning following heavy rain, the pavement surface is usually grooved so that the surface water film flows into the grooves and the peaks between grooves will still be in contact with

5382-547: The top of the pavement. A perforated plastic tube (5.9 in (15 cm) in diameter) is placed at the bottom of the ditch. The ditches are filled with gravel size crushed stone. Excessive moisture under a concrete pavement can cause pumping, cracking, and joint failure. In aviation charts, the surface type is usually abbreviated to a three-letter code. The most common hard surface types are asphalt and concrete. The most common soft surface types are grass and gravel. A runway of at least 1,800 m (5,900 ft) in length

5460-510: The use of aircraft as weapons and observation platforms. The earliest known aerial victory with a synchronized machine gun -armed fighter aircraft occurred in 1915, flown by German Luftstreitkräfte Lieutenant Kurt Wintgens . Fighter aces appeared; the greatest (by number of air victories) was Manfred von Richthofen . Alcock and Brown crossed the Atlantic non-stop for the first time in 1919. The first commercial flights traveled between

5538-581: The world. Some of the hundreds of versions found other purposes, like the AC-47 , a Vietnam War era gunship, which is still used in the Colombian Air Force . An airplane (aeroplane or plane) is a powered fixed-wing aircraft propelled by thrust from a jet engine or propeller . Planes come in many sizes, shapes, and wing configurations. Uses include recreation, transportation of goods and people, military, and research. A seaplane (hydroplane)

5616-421: Was an early aircraft design that had the modern monoplane tractor configuration . It had movable tail surfaces controlling both yaw and pitch, a form of roll control supplied either by wing warping or by ailerons and controlled by its pilot with a joystick and rudder bar. It was an important predecessor of his later Bleriot XI Channel -crossing aircraft of the summer of 1909. World War I served initiated

5694-441: Was by 11th-century monk Eilmer of Malmesbury , which failed. A 17th-century account states that 9th-century poet Abbas Ibn Firnas made a similar attempt, though no earlier sources record this event. In 1799, Sir George Cayley laid out the concept of the modern airplane as a fixed-wing machine with systems for lift, propulsion, and control. Cayley was building and flying models of fixed-wing aircraft as early as 1803, and built

5772-400: Was developed to investigate alternative methods of recovering spacecraft. Although this application was abandoned, publicity inspired hobbyists to adapt the flexible-wing airfoil for hang gliders. Initial research into many types of fixed-wing craft, including flying wings and lifting bodies was also carried out using unpowered prototypes. A hang glider is a glider aircraft in which

5850-574: Was in commercial service for more than 50 years, from 1958 to 2010. The Boeing 747 was the world's largest passenger aircraft from 1970 until it was surpassed by the Airbus A380 in 2005. The most successful aircraft is the Douglas DC-3 and its military version, the C-47 , a medium sized twin engine passenger or transport aircraft that has been in service since 1936 and is still used throughout

5928-550: Was tested with overhead rails to prevent it from rising. The test showed that it had enough lift to take off. The craft was uncontrollable, and Maxim abandoned work on it. The Wright brothers ' flights in 1903 with their Flyer I are recognized by the Fédération Aéronautique Internationale (FAI), the standard setting and record-keeping body for aeronautics , as "the first sustained and controlled heavier-than-air powered flight". By 1905,

6006-660: Was the first aircraft to exceed the speed of sound, flown by Chuck Yeager . In 1948–49, aircraft transported supplies during the Berlin Blockade . New aircraft types, such as the B-52 , were produced during the Cold War . The first jet airliner , the de Havilland Comet , was introduced in 1952, followed by the Soviet Tupolev Tu-104 in 1956. The Boeing 707 , the first widely successful commercial jet,

6084-446: Was used as a message for a rescue mission. Ancient and medieval Chinese sources report kites used for measuring distances, testing the wind, lifting men, signaling, and communication for military operations. Kite stories were brought to Europe by Marco Polo towards the end of the 13th century, and kites were brought back by sailors from Japan and Malaysia in the 16th and 17th centuries. Although initially regarded as curiosities, by

#876123