133-699: Westlake Recording Studios is a music recording studio in West Hollywood , California . Westlake Recording Studios was founded in the early 1970s by the American audio engineer Tom Hidley under the name Westlake Audio. Hidley was experienced in the development of audio technology, having collaborated with Madman Muntz in the development of the first car stereo in 1959, and along with Amnon "Ami" Hadani, he had previously set up another recording studio in Hollywood, TTG Studios , in 1965. The layout of
266-398: A Stroh violin which uses a conical horn connected to a diaphragm that in turn is connected to the violin bridge. The horn was no longer needed once electrical recording was developed. The long-playing 33 1 ⁄ 3 rpm microgroove LP record , was developed at Columbia Records and introduced in 1948. The short-playing but convenient 7-inch (18 cm) 45 rpm microgroove vinyl single
399-512: A microphone was used to convert the sound into an electrical signal that was amplified and used to actuate the recording stylus. This innovation eliminated the "horn sound" resonances characteristic of the acoustical process, produced clearer and more full-bodied recordings by greatly extending the useful range of audio frequencies, and allowed previously unrecordable distant and feeble sounds to be captured. During this time, several radio-related developments in electronics converged to revolutionize
532-685: A sound track . The projector used a steady light and a photodetector to convert these variations back into an electrical signal, which was amplified and sent to loudspeakers behind the screen. Optical sound became the standard motion picture audio system throughout the world and remains so for theatrical release prints despite attempts in the 1950s to substitute magnetic soundtracks. Currently, all release prints on 35 mm movie film include an analog optical soundtrack, usually stereo with Dolby SR noise reduction. In addition, an optically recorded digital soundtrack in Dolby Digital or Sony SDDS form
665-498: A telephone hybrid for putting telephone calls on the air, a POTS codec for receiving remote broadcasts , a dead air alarm for detecting unexpected silence , and a broadcast delay for dropping anything from coughs to profanity . In the U.S., stations licensed by the Federal Communications Commission (FCC) also must have an Emergency Alert System decoder (typically in the studio), and in
798-414: A 1,200-square-foot (110 m) tracking room, including a large piano isolation room. Studio A was where Michael Jackson's Thriller was recorded in 1982. Studio B is a full size studio that features a 72-channel Solid State Logic 4072 G series console and a large selection of outboard gear. It has a 500-square-foot (46 m) tracking room and a 65-square-foot (6.0 m) isolation room. Studio C
931-469: A Brahms Serenade, and the last movement of Bruckner's 8th Symphony with Von Karajan. Other early German stereophonic tapes are believed to have been destroyed in bombings. Not until Ampex introduced the first commercial two-track tape recorders in the late 1940s did stereo tape recording become commercially feasible. Despite the availability of multitrack tape, stereo did not become the standard system for commercial music recording for some years, and remained
1064-407: A coating of soot as the paper was passed under it. An 1860 phonautogram of " Au Clair de la Lune ", a French folk song, was played back as sound for the first time in 2008 by scanning it and using software to convert the undulating line, which graphically encoded the sound, into a corresponding digital audio file. Thomas Edison's work on two other innovations, the telegraph and the telephone, led to
1197-485: A condenser type developed there in 1916 and greatly improved in 1922, and the best amplifiers and test equipment. They had already patented an electromechanical recorder in 1918, and in the early 1920s, they decided to intensively apply their hardware and expertise to developing two state-of-the-art systems for electronically recording and reproducing sound: one that employed conventional discs and another that recorded optically on motion picture film. Their engineers pioneered
1330-401: A different machine, which records the combined signals (called printing ) to a 1 ⁄ 2 -inch two-track stereo tape, called a master . Before digital recording, the total number of available tracks onto which one could record was measured in multiples of 24, based on the number of 24-track tape machines being used. Most recording studios now use digital recording equipment, which limits
1463-402: A few crude telephone-based recording devices with no means of amplification, such as the telegraphone , it remained so until the 1920s. Between the invention of the phonograph in 1877 and the first commercial digital recordings in the early 1970s, arguably the most important milestone in the history of sound recording was the introduction of what was then called electrical recording , in which
SECTION 10
#17327903464431596-509: A high level of complexity and sophistication. The combined impact with innovations such as the endless loop broadcast cartridge led to significant changes in the pacing and production style of radio program content and advertising. In 1881, it was noted during experiments in transmitting sound from the Paris Opera that it was possible to follow the movement of singers on the stage if earpieces connected to different microphones were held to
1729-750: A home studio is challenging because they are usually the loudest instruments. Acoustic drums require sound isolation in this scenario, unlike electronic or sampled drums. Getting an authentic electric guitar amp sound including power-tube distortion requires a power attenuator or an isolation cabinet , or booth. A convenient compromise is amplifier modeling , whether a modeling amp, preamp/processor, or software-based guitar amp simulator. Sometimes, musicians replace loud, inconvenient instruments such as drums, with keyboards, which today often provide somewhat realistic sampling . The capability of digital recording introduced by ADAT and its comparatively low cost, originally introduced at $ 3995, were largely responsible for
1862-675: A home studio via the Internet. Additional outside audio connections are required for the studio/transmitter link for over-the-air stations, satellite dishes for sending and receiving shows, and for webcasting or podcasting . Sound recording and reproduction Sound recording and reproduction is the electrical , mechanical , electronic, or digital inscription and re-creation of sound waves, such as spoken voice, singing, instrumental music , or sound effects . The two main classes of sound recording technology are analog recording and digital recording . Acoustic analog recording
1995-413: A large role in the recording process. With software, a powerful, good quality computer with a fast processor can replace the mixing consoles , multitrack recording equipment, synthesizers, samplers and effects unit (reverb, echo, compression, etc.) that a recording studio required in the 1980s and 1990s. A computer thus outfitted is called a digital audio workstation , or DAW. While Apple Macintosh
2128-444: A lesser amount of diffused reflections from walls to make a good-sounding room. A drummer, vocalist, or guitar speaker cabinet, along with microphones, is acoustically isolated in the isolation booth. A typical professional recording studio today has a control room , a large live room , and one or more small isolation booths . All rooms are soundproofed by varying methods, including but not limited to, double-layer 5/8" sheetrock with
2261-585: A major consumer audio format and advances in electronic and mechanical miniaturization led to the development of the Sony Walkman , a pocket-sized cassette player introduced in 1979. The Walkman was the first personal music player and it gave a major boost to sales of prerecorded cassettes. A key advance in audio fidelity came with the Dolby A noise reduction system, invented by Ray Dolby and introduced into professional recording studios in 1966. It suppressed
2394-743: A master roll which had been created on a special piano, which punched holes in the master as a live performer played the song. Thus, the roll represented a recording of the actual performance of an individual, not just the more common method of punching the master roll through transcription of the sheet music. This technology to record a live performance onto a piano roll was not developed until 1904. Piano rolls were in continuous mass production from 1896 to 2008. A 1908 U.S. Supreme Court copyright case noted that, in 1902 alone, there were between 70,000 and 75,000 player pianos manufactured, and between 1,000,000 and 1,500,000 piano rolls produced. The first device that could record actual sounds as they passed through
2527-554: A much larger proportion of people to hear famous orchestras, operas, singers and bands, because even if a person could not afford to hear the live concert, they may be able to hear the recording. The availability of sound recording thus helped to spread musical styles to new regions, countries and continents. The cultural influence went in a number of directions. Sound recordings enabled Western music lovers to hear actual recordings of Asian, Middle Eastern and African groups and performers, increasing awareness of non-Western musical styles. At
2660-664: A number of other studios by the late 1970s. Westlake has been credited as "one of the first big commercial efforts to produce acoustically standardised 'interchangeable' rooms". Artists who have recorded music at Westlake Studios have included Rihanna , The Weeknd , Charli XCX , Café Quijano , Donna Summer , Giorgio Moroder , Quincy Jones , Billy Idol , Bruce Swedien , Gilberto Gil , Missy Elliott , Madonna , Marilyn Manson , Aaliyah and Justin Timberlake . Notable recordings produced at Westlake Studios have included Michael Jackson 's album, Thriller (April–November 1982),
2793-586: A private lounge. In addition to the five studios, Westlake has two smaller production rooms designed for overdubs, writing and mixing. Both of these rooms contain Solid State Logic AWS 900+'s, 24-channel controlled analog consoles. Both rooms contain small tracking rooms fit to record vocals, guitar, bass and many other smaller instruments. 34°05′27″N 118°20′54″W / 34.09095°N 118.348461°W / 34.09095; -118.348461 Recording studio A recording studio
SECTION 20
#17327903464432926-508: A regular stage or film set. In the era of acoustical recordings (prior to the introduction of microphones, electrical recording and amplification), the earliest recording studios were very basic facilities, being essentially soundproof rooms that isolated the performers from outside noise. During this era it was not uncommon for recordings to be made in any available location, such as a local ballroom, using portable acoustic recording equipment. In this period, master recordings were made by cutting
3059-402: A result, each performance of a song or piece would be slightly different. With the development of analog sound recording, though, a performance could be permanently fixed, in all of its elements: pitch, rhythm, timbre, ornaments and expression. This meant that many more elements of a performance would be captured and disseminated to other listeners. The development of sound recording also enabled
3192-410: A rotating cylinder (later disc) made from wax. Performers were typically grouped around a large acoustic horn (an enlarged version of the familiar gramophone horn). The acoustic energy from the voices or instruments was channeled through the horn to a diaphragm to a mechanical cutting lathe , which inscribed the signal as a modulated groove directly onto the surface of the master. Electrical recording
3325-497: A selection of instruments in their live room, typically instruments, amplifiers and speaker cabinets that are large, heavy, and difficult to transport (e.g., a Hammond organ ) or infeasible (as in the case of a grand piano ) to hire for a single recording session. Having musical instruments and equipment in the studio creates additional costs for a studio, as pianos have to be tuned and instruments and associated equipment needs to be maintained. General-purpose computers rapidly assumed
3458-402: A signal from one or more of the microphones in the studio could be routed to the loudspeaker in the echo chamber; the sound from the speaker reverberated through the chamber and the enhanced signal was picked up by the microphone at the other end. This echo-enhanced signal, which was often used to sweeten the sound of vocals, could then be blended in with the primary signal from the microphone in
3591-414: A single take. In the 1970s the large recording companies began to adopt multi-track recording and the emphasis shifted to isolation and sound-proofing, with treatments like echo and reverberation added separately during the mixing process, rather than being blended in during the recording. Generally, after an audio mix is set up on a 24-track tape machine, the tracks are played back together, mixed and sent to
3724-510: A specialist market during the 1950s. EMI (UK) was the first company to release commercial stereophonic tapes. They issued their first Stereosonic tape in 1954. Others quickly followed, under the His Master's Voice (HMV) and Columbia labels. 161 Stereosonic tapes were released, mostly classical music or lyric recordings. RCA imported these tapes into the USA. Although some HMV tapes released in
3857-464: A stereo soundtrack was Walt Disney's Fantasia , released in 1940. The 1941 release of Fantasia used the Fantasound sound system. This system used a separate film for the sound, synchronized with the film carrying the picture. The sound film had four double-width optical soundtracks, three for left, center, and right audio—and a fourth as a "control" track with three recorded tones that controlled
3990-469: A variety of materials including mild steel, thorn, and even sapphire. Discs had a distinctly limited playing life that varied depending on how they were manufactured. Earlier, purely acoustic methods of recording had limited sensitivity and frequency range. Mid-frequency range notes could be recorded, but very low and very high frequencies could not. Instruments such as the violin were difficult to transfer to disc. One technique to deal with this involved using
4123-429: A variety of techniques from remixing to pseudostereo . Magnetic tape transformed the recording industry. By the early 1950s, most commercial recordings were mastered on tape instead of recorded directly to disc. Tape facilitated a degree of manipulation in the recording process that was impractical with mixes and multiple generations of directly recorded discs. An early example is Les Paul 's 1951 recording of How High
Westlake Recording Studios - Misplaced Pages Continue
4256-408: A vibrant acoustic signature as the natural reverb enhanced the sound of the recording. In this period large, acoustically live halls were favored, rather than the acoustically dead booths and studio rooms that became common after the 1960s. Because of the limits of the recording technology, which did not allow for multitrack recording techniques, studios of the mid-20th century were designed around
4389-476: A wide frequency range and high audio quality are not. The development of analog sound recording in the nineteenth century and its widespread use throughout the twentieth century had a huge impact on the development of music. Before analog sound recording was invented, most music was as a live performance. Throughout the medieval , Renaissance , Baroque , Classical , and through much of the Romantic music era ,
4522-550: A worldwide standard for higher-quality recording on vinyl records. The Ernest Ansermet recording of Igor Stravinsky 's Petrushka was key in the development of full frequency range records and alerting the listening public to high fidelity in 1946. Until the mid-1960s, record companies mixed and released most popular music in monophonic sound. From mid-1960s until the early 1970s, major recordings were commonly released in both mono and stereo. Recordings originally released only in mono have been rerendered and released in stereo using
4655-474: Is amplified and connected to a loudspeaker to produce sound. Long before sound was first recorded, music was recorded—first by written music notation , then also by mechanical devices (e.g., wind-up music boxes , in which a mechanism turns a spindle, which plucks metal tines, thus reproducing a melody ). Automatic music reproduction traces back as far as the 9th century, when the Banū Mūsā brothers invented
4788-441: Is a 200-square-foot (19 m) piano isolation room and a 176-foot (54 m) isolation room. Studio D has a private entrance and features 3 lounge areas including a loft that overlooks the tracking room. Studio E is a mixing suite that features a Solid State Logic 9072 J Series console. Out of all the studios at Westlake, Studio E has the largest selection of outboard gear. Studio E has a 52-square-foot (4.8 m) vocal booth and
4921-405: Is a full size studio that features a 72-channel Solid State Logic 9072 J series console and a large selection of outboard gear. It has a 1,000-square-foot (93 m) tracking room and a large private lounge. Studio D is Westlake's largest room. It features a Solid State Logic XL 9000 K console and a large selection of outboard gear. The main tracking area is 1,120 square feet (104 m) and there
5054-428: Is a key goal, the musicians, singers, audio engineers and record producers still need to be able to see each other, to see cue gestures and conducting by a bandleader. As such, the live room, isolation booths, vocal booths and control room typically have windows. Amplified instruments, like electric guitars and digital keyboards, may be connected directly to the recording console using DI units and performance recorded in
5187-613: Is a specialized facility for recording and mixing of instrumental or vocal musical performances, spoken words, and other sounds. They range in size from a small in-home project studio large enough to record a single singer-guitarist, to a large building with space for a full orchestra of 100 or more musicians. Ideally, both the recording and monitoring (listening and mixing) spaces are specially designed by an acoustician or audio engineer to achieve optimum acoustic properties (acoustic isolation or diffusion or absorption of reflected sound reverberation that could otherwise interfere with
5320-411: Is achieved by a microphone diaphragm that senses changes in atmospheric pressure caused by acoustic sound waves and records them as a mechanical representation of the sound waves on a medium such as a phonograph record (in which a stylus cuts grooves on a record). In magnetic tape recording, the sound waves vibrate the microphone diaphragm and are converted into a varying electric current , which
5453-409: Is essential to preserving the ability to fine-tune lines up to the last minute. Sometimes, if the rapport between the lead actors is strong enough and the animation studio can afford it, the producers may use a recording studio configured with multiple isolation booths in which the actors can see each another and the director. This enables the actors to react to one another in real time as if they were on
Westlake Recording Studios - Misplaced Pages Continue
5586-417: Is likely to be present. An optically recorded timecode is also commonly included to synchronize CDROMs that contain a DTS soundtrack. This period also saw several other historic developments including the introduction of the first practical magnetic sound recording system, the magnetic wire recorder , which was based on the work of Danish inventor Valdemar Poulsen . Magnetic wire recorders were effective, but
5719-422: Is then converted to a varying magnetic field by an electromagnet , which makes a representation of the sound as magnetized areas on a plastic tape with a magnetic coating on it. Analog sound reproduction is the reverse process, with a larger loudspeaker diaphragm causing changes to atmospheric pressure to form acoustic sound waves. Digital recording and reproduction converts the analog sound signal picked up by
5852-490: Is used for most studio work, there is a breadth of software available for Microsoft Windows and Linux . If no mixing console is used and all mixing is done using only a keyboard and mouse, this is referred to as mixing in the box (ITB). OTB describes mixing with other hardware and not just the PC software. A small, personal recording studio is sometimes called a project studio or home studio . Such studios often cater to
5985-568: The Chladni patterns produced by sound in stone representations, although this theory has not been conclusively proved. In the 14th century, a mechanical bell-ringer controlled by a rotating cylinder was introduced in Flanders . Similar designs appeared in barrel organs (15th century), musical clocks (1598), barrel pianos (1805), and music boxes ( c. 1800 ). A music box is an automatic musical instrument that produces sounds by
6118-514: The RCA company in the 1930s were crucial to the crooning style perfected by Bing Crosby , and the famous Neumann U 47 condenser microphone was one of the most widely used from the 1950s. This model is still widely regarded by audio professionals as one of the best microphones of its type ever made. Learning the correct placement of microphones is a major part of the training of young engineers, and many became extremely skilled in this craft. Well into
6251-536: The compact disc (CD) in 1982 brought significant improvements in the quality and durability of recordings. The CD initiated another massive wave of change in the consumer music industry, with vinyl records effectively relegated to a small niche market by the mid-1990s. The record industry fiercely resisted the introduction of digital systems, fearing wholesale piracy on a medium able to produce perfect copies of original released recordings. The most recent and revolutionary developments have been in digital recording, with
6384-452: The graphic equalizer , which could be connected together to create a complete home sound system. These developments were rapidly taken up by major Japanese electronics companies, which soon flooded the world market with relatively affordable, high-quality transistorized audio components. By the 1980s, corporations like Sony had become world leaders in the music recording and playback industry. The advent of digital sound recording and later
6517-407: The "studio" or "live room" equipped with microphones and mic stands, where instrumentalists and vocalists perform; and the " control room ", where audio engineers, sometimes with record producers, as well, operate professional audio mixing consoles , effects units , or computers with specialized software suites to mix , manipulate (e.g., by adjusting the equalization and adding effects) and route
6650-406: The 1920s, Phonofilm and other early motion picture sound systems employed optical recording technology, in which the audio signal was graphically recorded on photographic film. The amplitude variations comprising the signal were used to modulate a light source which was imaged onto the moving film through a narrow slit, allowing the signal to be photographed as variations in the density or width of
6783-577: The 1950s and 1960s, the sound of pop recordings was further defined by the introduction of proprietary sound processing devices such as equalizers and compressors, which were manufactured by specialist electronics companies. One of the best known of these was the Pultec equalizer which was used by almost all the major commercial studios of the time. With the introduction of multi-track recording , it became possible to record instruments and singers separately and at different times on different tracks on tape. In
SECTION 50
#17327903464436916-513: The 1960s, in the classical field it was not uncommon for engineers to make high-quality orchestral recordings using only one or two microphones suspended above the orchestra. In the 1960s, engineers began experimenting with placing microphones much closer to instruments than had previously been the norm. The distinctive rasping tone of the horn sections on the Beatles recordings " Good Morning Good Morning " and " Lady Madonna " were achieved by having
7049-549: The 1980s, but in the 1960s the pre-recorded 8-track tape was launched as a consumer audio format by the Lear Jet aircraft company. Aimed particularly at the automotive market, they were the first practical, affordable car hi-fi systems, and could produce sound quality superior to that of the compact cassette. The smaller size and greater durability – augmented by the ability to create home-recorded music mixtapes since 8-track recorders were rare – saw
7182-478: The 30th Street Studio at 207 East 30th Street, the CBS Studio Building at 49 East 52nd Street, Liederkranz Hall at 111 East 58th Street between Park and Lexington Avenues (a building built by and formerly belonging to a German cultural and musical society, The Liederkranz Club and Society), and one of their earliest recording studios, Studio A at 799 Seventh Avenue. Electric recording studios in
7315-455: The 30th Street Studios in the late 1940s and A&R manager Mitch Miller had tweaked it to perfection, Miller issued a standing order that the drapes and other fittings were not to be touched, and the cleaners had specific orders never to mop the bare wooden floor for fear it might alter the acoustic properties of the hall. There were several other features of studios in this period that contributed to their unique sonic signatures. As well as
7448-607: The Jedi . Westlake has a total of seven recording studios, including four with full size live rooms, two production rooms and a mixing suite. Studios A and B are located on Beverly Boulevard in Los Angeles and Studios C, D, E, Production Room 1 and Production Room 2 are located on Santa Monica Boulevard , CA in West Hollywood, CA . Studio A is one of the most historic rooms at Westlake. The control room of Studio A features an 80-channel Solid State Logic XL 9000 K console and
7581-483: The Moon , on which Paul played eight overdubbed guitar tracks. In the 1960s Brian Wilson of The Beach Boys , Frank Zappa , and The Beatles (with producer George Martin ) were among the first popular artists to explore the possibilities of multitrack recording techniques and effects on their landmark albums Pet Sounds , Freak Out! , and Sgt. Pepper's Lonely Hearts Club Band . The next important innovation
7714-597: The USA cost up to $ 15, two-track stereophonic tapes were more successful in America during the second half of the 1950s. The history of stereo recording changed after the late 1957 introduction of the Westrex stereo phonograph disc , which used the groove format developed earlier by Blumlein. Decca Records in England came out with FFRR (Full Frequency Range Recording) in the 1940s, which became internationally accepted as
7847-500: The additional benefit of being marginally louder than cylinders. Sales of the gramophone record overtook the cylinder ca. 1910, and by the end of World War I the disc had become the dominant commercial recording format. Edison, who was the main producer of cylinders, created the Edison Disc Record in an attempt to regain his market. The double-sided (nominally 78 rpm) shellac disc was the standard consumer music format from
7980-407: The air (but could not play them back—the purpose was only visual study) was the phonautograph , patented in 1857 by Parisian inventor Édouard-Léon Scott de Martinville . The earliest known recordings of the human voice are phonautograph recordings, called phonautograms , made in 1857. They consist of sheets of paper with sound-wave-modulated white lines created by a vibrating stylus that cut through
8113-438: The amount of data that can be stored on a single medium, such as Super Audio CD , DVD-A , Blu-ray Disc , and HD DVD became available, longer programs of higher quality fit onto a single disc. Sound files are readily downloaded from the Internet and other sources, and copied onto computers and digital audio players. Digital audio technology is now used in all areas of audio, from casual use of music files of moderate quality to
SECTION 60
#17327903464438246-417: The background of hiss, which was the only easily audible downside of mastering on tape instead of recording directly to disc. A competing system, dbx , invented by David Blackmer, also found success in professional audio. A simpler variant of Dolby's noise reduction system, known as Dolby B, greatly improved the sound of cassette tape recordings by reducing the especially high level of hiss that resulted from
8379-555: The basis of all electronic sound systems until the commercial introduction of the first transistor -based audio devices in the mid-1950s. During World War I, engineers in the United States and Great Britain worked on ways to record and reproduce, among other things, the sound of a German U-boat for training purposes. Acoustical recording methods of the time could not reproduce the sounds accurately. The earliest results were not promising. The first electrical recording issued to
8512-519: The case of full-power stations, an encoder that can interrupt programming on all channels which a station transmits to broadcast urgent warnings. Computers are used for playing ads , jingles , bumpers , soundbites , phone calls, sound effects , traffic and weather reports , and now are able to perform full broadcast automation when no staff are present. Digital mixing consoles can be interconnected via audio over Ethernet . Network connections allow remote access , so that DJs can do shows from
8645-454: The cassette become the dominant consumer format for portable audio devices in the 1970s and 1980s. There had been experiments with multi-channel sound for many years – usually for special musical or cultural events – but the first commercial application of the concept came in the early 1970s with the introduction of Quadraphonic sound. This spin-off development from multitrack recording used four tracks (instead of
8778-407: The cassette's miniaturized tape format. The compact cassette format also benefited from improvements to the tape itself as coatings with wider frequency responses and lower inherent noise were developed, often based on cobalt and chrome oxides as the magnetic material instead of the more usual iron oxide. The multitrack audio cartridge had been in wide use in the radio industry, from the late 1950s to
8911-447: The commercial recording, distribution, and sale of sound recordings became a growing new international industry, with the most popular titles selling millions of units by the early 1900s. A process for mass-producing duplicate wax cylinders by molding instead of engraving them was put into effect in 1901. The development of mass-production techniques enabled cylinder recordings to become a major new consumer item in industrial countries and
9044-489: The concept of grouping musicians (e.g., the rhythm section or a horn section ) and singers (e.g., a group of backup singers ), rather than separating them, and placing the performers and the microphones strategically to capture the complex acoustic and harmonic interplay that emerged during the performance. In the 2000s, modern sound stages still sometimes use this approach for large film scoring projects that use large orchestras. Because of their superb acoustics, many of
9177-480: The consideration of the physical dimensions of the room itself to make the room respond to sound in the desired way. Acoustical treatment includes and the use of absorption and diffusion materials on the surfaces inside the room. To control the amount of reverberation, rooms in a recording studio may have a reconfigurable combination of reflective and non-reflective surfaces. Soundproofing provides sonic isolation between rooms and prevents sound from entering or leaving
9310-436: The control room. This greatly enhances the communication between the producer and engineer with the player, as studio mics, headphones and talkback are unnecessary. Recording studios are carefully designed around the principles of room acoustics to create a set of spaces with the acoustical properties required for recording sound with accuracy. Architectural acoustics includes acoustical treatment and soundproofing and also
9443-505: The controversy came to focus on concern for the perception of moving image and sound. There are individual and cultural preferences for either method. While approaches and opinions vary, some emphasize sound as paramount, others focus on technology preferences as the deciding factor. Analog fans might embrace limitations as strengths of the medium inherent in the compositional, editing, mixing, and listening phases. Digital advocates boast flexibility in similar processes. This debate fosters
9576-456: The correct equipment, of the released music. It eventually faded out in the late 1970s, although this early venture paved the way for the eventual introduction of domestic surround sound systems in home theatre use, which gained popularity following the introduction of the DVD. The replacement of the relatively fragile vacuum tube by the smaller, rugged and efficient transistor also accelerated
9709-538: The cumbersome disc-to-disc editing procedures previously in some limited use, together with tape's consistently high audio quality finally convinced radio networks to routinely prerecord their entertainment programming, most of which had formerly been broadcast live. Also, for the first time, broadcasters, regulators and other interested parties were able to undertake comprehensive audio logging of each day's radio broadcasts. Innovations like multitracking and tape echo allowed radio programs and advertisements to be produced to
9842-407: The cylinder was the main consumer format from the late 1880s until around 1910. The next major technical development was the invention of the gramophone record , generally credited to Emile Berliner and patented in 1887, though others had demonstrated similar disk apparatus earlier, most notably Alexander Graham Bell in 1881. Discs were easier to manufacture, transport and store, and they had
9975-572: The development of the phonograph. Edison was working on a machine in 1877 that would transcribe telegraphic signals onto paper tape, which could then be transferred over the telegraph again and again. The phonograph was both in a cylinder and a disc form. On April 30, 1877, French poet, humorous writer and inventor Charles Cros submitted a sealed envelope containing a letter to the Academy of Sciences in Paris fully explaining his proposed method, called
10108-490: The development of various uncompressed and compressed digital audio file formats , processors capable and fast enough to convert the digital data to sound in real time , and inexpensive mass storage . This generated new types of portable digital audio players . The minidisc player, using ATRAC compression on small, re-writeable discs was introduced in the 1990s, but became obsolescent as solid-state non-volatile flash memory dropped in price. As technologies that increase
10241-507: The earliest known mechanical musical instrument, in this case, a hydropowered (water-powered) organ that played interchangeable cylinders. According to Charles B. Fowler, this "... cylinder with raised pins on the surface remained the basic device to produce and reproduce music mechanically until the second half of the nineteenth century." Carvings in the Rosslyn Chapel from the 1560s may represent an early attempt to record
10374-444: The early 1910s to the late 1950s. In various permutations, the audio disc format became the primary medium for consumer sound recordings until the end of the 20th century. Although there was no universally accepted speed, and various companies offered discs that played at several different speeds, the major recording companies eventually settled on a de facto industry standard of nominally 78 revolutions per minute. The specified speed
10507-402: The high recording speeds required, they used enormous reels about one meter in diameter, and the thin tape frequently broke, sending jagged lengths of razor steel flying around the studio. Magnetic tape recording uses an amplified electrical audio signal to generate analogous variations of the magnetic field produced by a tape head , which impresses corresponding variations of magnetization on
10640-412: The inherent sound of the large recording rooms, many of the best studios incorporated specially-designed echo chambers , purpose-built rooms which were often built beneath the main studio. These were typically long, low rectangular spaces constructed from hard, sound-reflective materials like concrete, fitted with a loudspeaker at one end and one or more microphones at the other. During a recording session,
10773-664: The larger studios were converted churches. Examples include George Martin 's AIR Studios in London, Columbia Records 30th Street Studio in New York City, and Pythian Temple studio in New York. Facilities like the Columbia Records 30th Street Studio in New York and Abbey Road Studios in London were renowned for their identifiable sound—which was (and still is) easily identifiable by audio professionals—and for
10906-540: The main way that songs and instrumental pieces were recorded was through music notation . While notation indicates the pitches of the melody and their rhythm many aspects of the performance are undocumented. Indeed, in the Medieval era, Gregorian chant did not indicate the rhythm of the chant. In the Baroque era, instrumental pieces often lack a tempo indication and usually none of the ornaments were written down. As
11039-475: The microphone to a digital form by the process of sampling . This lets the audio data be stored and transmitted by a wider variety of media. Digital recording stores audio as a series of binary numbers (zeros and ones) representing samples of the amplitude of the audio signal at equal time intervals, at a sample rate high enough to convey all sounds capable of being heard . A digital audio signal must be reconverted to analog form during playback before it
11172-584: The mid-20th century often lacked isolation booths, sound baffles , and sometimes even speakers. A major reason that isolation was not used was that recordings in this period were typically made as live ensemble takes and all the performers needed to be able to see each other and the ensemble leader while playing. The recording engineers who trained in this period learned to take advantage of the complex acoustic effects that could be created through leakage between different microphones and groups of instruments, and these technicians became extremely skilled at capturing
11305-422: The mid-20th century, recordings were analog , made on 1 ⁄ 4 -inch or 1 ⁄ 2 -inch magnetic tape , or, more rarely, on 35 mm magnetic film , with multitrack recording reaching 8 tracks in the 1950s, 16 in 1968, and 32 in the 1970s. The commonest such tape is the 2-inch analog, capable of containing up to 24 individual tracks. Throughout the 1960s many pop classics were still recorded live in
11438-651: The most demanding professional applications. New applications such as internet radio and podcasting have appeared. Technological developments in recording, editing, and consuming have transformed the record , movie and television industries in recent decades. Audio editing became practicable with the invention of magnetic tape recording , but technologies like MIDI , sound synthesis and digital audio workstations allow greater control and efficiency for composers and artists. Digital audio techniques and mass storage have reduced recording costs such that high-quality recordings can be produced in small studios. Today,
11571-402: The moving tape. In playback mode, the signal path is reversed, the tape head acting as a miniature electric generator as the varyingly magnetized tape passes over it. The original solid steel ribbon was replaced by a much more practical coated paper tape, but acetate soon replaced paper as the standard tape base. Acetate has fairly low tensile strength and if very thin it will snap easily, so it
11704-599: The next few years, the lesser record companies licensed or developed other electrical recording systems. By 1929 only the budget label Harmony was still issuing new recordings made by the old acoustical process. Comparison of some surviving Western Electric test recordings with early commercial releases indicates that the record companies artificially reduced the frequency range of recordings so they would not overwhelm non-electronic playback equipment, which reproduced very low frequencies as an unpleasant rattle and rapidly wore out discs with strongly recorded high frequencies. In
11837-488: The next two years, Blumlein developed stereo microphones and a stereo disc-cutting head, and recorded a number of short films with stereo soundtracks. In the 1930s, experiments with magnetic tape enabled the development of the first practical commercial sound systems that could record and reproduce high-fidelity stereophonic sound . The experiments with stereo during the 1930s and 1940s were hampered by problems with synchronization. A major breakthrough in practical stereo sound
11970-524: The number of available tracks only on the basis of the mixing console 's or computer hardware interface's capacity and the ability of the hardware to cope with processing demands. Analog tape machines are still used in some cases for their unique sonic characteristics. Radio studios are very similar to recording studios, particularly in the case of production studios which are not normally used on-air , such as studios where interviews are taped for later broadcast. This type of studio would normally have all of
12103-485: The number-one-selling album of all time; and Alanis Morissette 's Jagged Little Pill (1994–1995). Westlake Studios have also been used to produce audio material for films, television shows and commercials. In June 1980, National Public Radio , in a co-production with the BBC , used Westlake Studios to record a 13-part radio adaptation of Star Wars . NPR returned to Westlake in 1996 to record its production of Return of
12236-405: The only issued electrical recording. Several record companies and independent inventors, notably Orlando Marsh , experimented with equipment and techniques for electrical recording in the early 1920s. Marsh's electrically recorded Autograph Records were already being sold to the public in 1924, a year before the first such offerings from the major record companies, but their overall sound quality
12369-416: The paleophone. Though no trace of a working paleophone was ever found, Cros is remembered by some historians as an early inventor of a sound recording and reproduction machine. The first practical sound recording and reproduction device was the mechanical phonograph cylinder , invented by Thomas Edison in 1877 and patented in 1878. The invention soon spread across the globe and over the next two decades
12502-665: The playback volume of the three audio channels. Because of the complex equipment this system required, Disney exhibited the movie as a roadshow, and only in the United States. Regular releases of the movie used standard mono optical 35 mm stock until 1956, when Disney released the film with a stereo soundtrack that used the Cinemascope four-track magnetic sound system. German audio engineers working on magnetic tape developed stereo recording by 1941. Of 250 stereophonic recordings made during WW2, only three survive: Beethoven's 5th Piano Concerto with Walter Gieseking and Arthur Rother,
12635-808: The process of making a recording is separated into tracking, mixing and mastering . Multitrack recording makes it possible to capture signals from several microphones, or from different takes to tape, disc or mass storage allowing previously unavailable flexibility in the mixing and mastering stages. There are many different digital audio recording and processing programs running under several computer operating systems for all purposes, ranging from casual users and serious amateurs working on small projects to professional sound engineers who are recording albums, film scores and doing sound design for video games . Digital dictation software for recording and transcribing speech has different requirements; intelligibility and flexible playback facilities are priorities, while
12768-502: The property. A Recording studio in an urban environment must be soundproofed on its outer shell to prevent noises from the surrounding streets and roads from being picked up by microphones inside. Equipment found in a recording studio commonly includes: Not all music studios are equipped with musical instruments. Some smaller studios do not have instruments, and bands and artists are expected to bring their own instruments, amplifiers, and speakers. However, major recording studios often have
12901-549: The public, with little fanfare, was of November 11, 1920, funeral service for The Unknown Warrior in Westminster Abbey , London. The recording engineers used microphones of the type used in contemporary telephones. Four were discreetly set up in the abbey and wired to recording equipment in a vehicle outside. Although electronic amplification was used, the audio was weak and unclear, as only possible in those circumstances. For several years, this little-noted disc remained
13034-590: The recording industry. Tape made possible the first sound recordings totally created by electronic means, opening the way for the bold sonic experiments of the Musique Concrète school and avant-garde composers like Karlheinz Stockhausen , which in turn led to the innovative pop music recordings of artists such as the Beatles and the Beach Boys . The ease and accuracy of tape editing, as compared to
13167-540: The recording process. These included improved microphones and auxiliary devices such as electronic filters, all dependent on electronic amplification to be of practical use in recording. In 1906, Lee De Forest invented the Audion triode vacuum tube, an electronic valve that could amplify weak electrical signals. By 1915, it was in use in long-distance telephone circuits that made conversations between New York and San Francisco practical. Refined versions of this tube were
13300-646: The rights to the Blattnerphone, and newly developed Marconi-Stille recorders were installed in the BBC's Maida Vale Studios in March 1935. The tape used in Blattnerphones and Marconi-Stille recorders was the same material used to make razor blades, and not surprisingly the fearsome Marconi-Stille recorders were considered so dangerous that technicians had to operate them from another room for safety. Because of
13433-459: The rise of project studios in the 1990s. Today's project studios are built around software-based DAWs running on standard PC hardware. An isolation booth is either a partially enclosed area in the live room or a completely separate small room built adjacent to the live room that is both soundproofed to keep out external sounds and keep in the internal sounds. Like all the other recording rooms in sound industry, isolation booths designed for having
13566-459: The rooms at Westlake Studios aimed for an acoustic design that could give a fairly flat frequency response at the recording position, with low reverberation delay and extensive use of bass traps . As the need to transfer audio material between different studios grew, there was an increasing demand for standardization across the recording industry; the success of Hidley's acoustic design was copied at other sites, and "Westlake-style" rooms spread to
13699-466: The sale of consumer high-fidelity sound systems from the 1960s onward. In the 1950s, most record players were monophonic and had relatively low sound quality. Few consumers could afford high-quality stereophonic sound systems. In the 1960s, American manufacturers introduced a new generation of modular hi-fi components — separate turntables, pre-amplifiers, amplifiers, both combined as integrated amplifiers, tape recorders, and other ancillary equipment like
13832-444: The same equipment that any other audio recording studio would have, particularly if it is at a large station, or at a combined facility that houses a station group, but is also designed for groups of people to work collaboratively in a live-to-air situation. Broadcast studios also use many of the same principles such as sound isolation, with adaptations suited to the live on-air nature of their use. Such equipment would commonly include
13965-505: The same tape many times, sounds could be duplicated from tape to tape with only minor loss of quality, and recordings could now be very precisely edited by physically cutting the tape and rejoining it. Within a few years of the introduction of the first commercial tape recorder—the Ampex 200 model, launched in 1948—American musician-inventor Les Paul had invented the first multitrack tape recorder , ushering in another technical revolution in
14098-514: The same time, sound recordings enabled music lovers outside the West to hear the most famous North American and European groups and singers. As digital recording developed, so did a controversy commonly known as the analog versus digital controversy. Audio professionals, audiophiles, consumers, musicians alike contributed to the debate based on their interaction with the media and the preferences for analog or digital processes. Scholarly discourse on
14231-401: The saxophone players position their instruments so that microphones were virtually inside the mouth of the horn. The unique sonic characteristics of the major studios imparted a special character to many of the most famous popular recordings of the 1950s and 1960s, and the recording companies jealously guarded these facilities. According to sound historian David Simons, after Columbia took over
14364-508: The seams offset from layer to layer on both sides of the wall that is filled with foam, batten insulation, a double wall, which is an insulated wall built next to another insulated wall with an air gap in-between, by adding foam to the interior walls and corners, and by using two panes of thick glass with an air gap between them. The surface densities of common building materials determines the transmission loss of various frequencies through materials. Thomas A. Watson invented, but did not patent,
14497-523: The skill of their staff engineers. As the need to transfer audio material between different studios grew, there was an increasing demand for standardization in studio design across the recording industry, and Westlake Recording Studios in West Hollywood was highly influential in the 1970s in the development of standardized acoustic design. In New York City, Columbia Records had some of the most highly respected sound recording studios, including
14630-501: The smaller independent studios were often owned by skilled electronics engineers who designed and built their own desks and other equipment. A good example of this is Gold Star Studios in Los Angeles, the site of many famous American pop recordings of the 1960s. Co-owner David S. Gold built the studio's main mixing desk and many additional pieces of equipment and he also designed the studio's unique trapezoidal echo chambers. During
14763-474: The sound and keep it from bleeding into the other microphones, allowing better independent control of each instrument channel at the mixing console . In animation, vocal performances are normally recorded in individual sessions, and the actors have to imagine (with the help of the director or a reader) they are involved in dialogue. Animated films often evolve rapidly during both development and production, so keeping vocal tracks from bleeding into each other
14896-408: The sound for analog or digital recording . The engineers and producers listen to the live music and the recorded "tracks" on high-quality monitor speakers or headphones . Often, there will be smaller rooms called isolation booths to accommodate loud instruments such as drums or electric guitar amplifiers and speakers, to keep these sounds from being audible to the microphones that are capturing
15029-401: The sound heard by the listener). Recording studios may be used to record singers, instrumental musicians (e.g., electric guitar, piano, saxophone, or ensembles such as orchestras), voice-over artists for advertisements or dialogue replacement in film, television, or animation, Foley , or to record their accompanying musical soundtracks. The typical recording studio consists of a room called
15162-566: The sound quality was poor, so between the wars, they were primarily used for voice recording and marketed as business dictating machines. In 1924, a German engineer, Kurt Stille, improved the Telegraphone with an electronic amplifier. The following year, Ludwig Blattner began work that eventually produced the Blattnerphone, which used steel tape instead of wire. The BBC started using Blattnerphones in 1930 to record radio programs. In 1933, radio pioneer Guglielmo Marconi 's company purchased
15295-445: The soundproof booth for use in demonstrating the telephone with Alexander Graham Bell in 1877. There are variations of the same concept, including a portable standalone isolation booth and a guitar speaker isolation cabinet. A gobo panel achieves the same effect to a much more moderate extent; for example, a drum kit that is too loud in the live room or on stage can have acrylic glass see-through gobo panels placed around it to deflect
15428-474: The sounds from other instruments or voices, or to provide "drier" rooms for recording vocals or quieter acoustic instruments such as an acoustic guitar or a fiddle . Major recording studios typically have a range of large, heavy, and hard-to-transport instruments and music equipment in the studio, such as a grand piano , Hammond organ , electric piano , harp , and drums . Recording studios generally consist of three or more rooms: Even though sound isolation
15561-444: The specific needs of an individual artist or are used as a non-commercial hobby. The first modern project studios came into being during the mid-1980s, with the advent of affordable multitrack recording devices, synthesizers and microphones. The phenomenon has flourished with falling prices of MIDI equipment and accessories, as well as inexpensive direct to disk recording products. Recording drums and amplified electric guitar in
15694-435: The studio and mixed into the track as the master recording was being made. Special equipment was another notable feature of the classic recording studio. The biggest studios were owned and operated by large media companies like RCA, Columbia and EMI, who typically had their own electronics research and development divisions that designed and built custom-made recording equipment and mixing consoles for their studios. Likewise,
15827-479: The system and both made their earliest published electrical recordings in February 1925, but neither actually released them until several months later. To avoid making their existing catalogs instantly obsolete, the two long-time archrivals agreed privately not to publicize the new process until November 1925, by which time enough electrically recorded repertory would be available to meet the anticipated demand. During
15960-495: The two ears. This discovery was commercialized in 1890 with the Théâtrophone system, which operated for over forty years until 1932. In 1931, Alan Blumlein , a British electronics engineer working for EMI , designed a way to make the sound of an actor in a film follow his movement across the screen. In December 1931, he submitted a patent application including the idea, and in 1933 this became UK patent number 394,325 . Over
16093-615: The two used in stereo) and four speakers to create a 360-degree audio field around the listener. Following the release of the first consumer 4-channel hi-fi systems, a number of popular albums were released in one of the competing four-channel formats; among the best known are Mike Oldfield 's Tubular Bells and Pink Floyd 's The Dark Side of the Moon . Quadraphonic sound was not a commercial success, partly because of competing and somewhat incompatible four-channel sound systems (e.g., CBS , JVC , Dynaco and others all had systems) and generally poor quality, even when played as intended on
16226-571: The unique acoustic properties of their studios and the musicians in performance. It was not until the 1960s, with the introduction of the high-fidelity headphones that it became common practice for performers to use these to monitor their performance during recording and listen to playbacks. The use of different kinds of microphones and their placement around the studio is a crucial part of the recording process, and particular brands of microphones are used by engineers for their specific audio characteristics. The smooth-toned ribbon microphones developed by
16359-450: The use of a set of pins placed on a revolving cylinder or disc so as to pluck the tuned teeth (or lamellae ) of a steel comb. The fairground organ , developed in 1892, used a system of accordion-folded punched cardboard books. The player piano , first demonstrated in 1876, used a punched paper scroll that could store a long piece of music. The most sophisticated of the piano rolls were "hand-played," meaning that they were duplicates from
16492-566: The use of mechanical analogs of electrical circuits and developed a superior "rubber line" recorder for cutting the groove into the wax master in the disc recording system. By 1924, such dramatic progress had been made that Western Electric arranged a demonstration for the two leading record companies, the Victor Talking Machine Company and the Columbia Phonograph Company . Both soon licensed
16625-549: Was 78.26 rpm in America and 77.92 rpm throughout the rest of the world. The difference in speeds was due to the difference in the cycle frequencies of the AC electricity that powered the stroboscopes used to calibrate recording lathes and turntables. The nominal speed of the disc format gave rise to its common nickname, the "seventy-eight" (though not until other speeds had become available). Discs were made of shellac or similar brittle plastic-like materials, played with needles made from
16758-414: Was acceptable. The compact 45 format required very little material. Vinyl offered improved performance, both in stamping and in playback. Vinyl records were, over-optimistically, advertised as "unbreakable". They were not, but they were much less fragile than shellac, which had itself once been touted as "unbreakable" compared to wax cylinders. Sound recording began as a purely mechanical process. Except for
16891-442: Was common by the early 1930s, and mastering lathes were electrically powered, but master recordings still had to be cut into a disc, by now a lacquer, also known as an Acetate disc . In line with the prevailing musical trends, studios in this period were primarily designed for the live recording of symphony orchestras and other large instrumental ensembles. Engineers soon found that large, reverberant spaces like concert halls created
17024-507: Was further improved just after World War II by American audio engineer John T. Mullin with backing from Bing Crosby Enterprises. Mullin's pioneering recorders were modifications of captured German recorders. In the late 1940s, the Ampex company produced the first tape recorders commercially available in the US. Magnetic tape brought about sweeping changes in both radio and the recording industry. Sound could be recorded, erased and re-recorded on
17157-530: Was in turn eventually superseded by polyester. This technology, the basis for almost all commercial recording from the 1950s to the 1980s, was developed in the 1930s by German audio engineers who also rediscovered the principle of AC biasing (first used in the 1920s for wire recorders ), which dramatically improved the frequency response of tape recordings. The K1 Magnetophon was the first practical tape recorder, developed by AEG in Germany in 1935. The technology
17290-411: Was introduced by RCA Victor in 1949. In the US and most developed countries, the two new vinyl formats completely replaced 78 rpm shellac discs by the end of the 1950s, but in some corners of the world, the 78 lingered on far into the 1960s. Vinyl was much more expensive than shellac, one of the several factors that made its use for 78 rpm records very unusual, but with a long-playing disc the added cost
17423-448: Was made by Bell Laboratories , who in 1937 demonstrated a practical system of two-channel stereo, using dual optical sound tracks on film. Major movie studios quickly developed three-track and four-track sound systems, and the first stereo sound recording for a commercial film was made by Judy Garland for the MGM movie Listen, Darling in 1938. The first commercially released movie with
17556-479: Was small cartridge-based tape systems, of which the compact cassette , commercialized by the Philips electronics company in 1964, is the best known. Initially a low-fidelity format for spoken-word voice recording and inadequate for music reproduction, after a series of improvements it entirely replaced the competing consumer tape formats: the larger 8-track tape (used primarily in cars). The compact cassette became
17689-410: Was too low to demonstrate any obvious advantage over traditional acoustical methods. Marsh's microphone technique was idiosyncratic and his work had little if any impact on the systems being developed by others. Telephone industry giant Western Electric had research laboratories with material and human resources that no record company or independent inventor could match. They had the best microphone,
#442557