A camera lens (also known as photographic lens or photographic objective ) is an optical lens or assembly of lenses used in conjunction with a camera body and mechanism to make images of objects either on photographic film or on other media capable of storing an image chemically or electronically .
128-406: An f-number is a measure of the light-gathering ability of an optical system such as a camera lens . It is calculated by dividing the system's focal length by the diameter of the entrance pupil ("clear aperture "). The f-number is also known as the focal ratio , f-ratio , or f-stop , and it is key in determining the depth of field , diffraction , and exposure of a photograph. The f-number
256-468: A NASA/Zeiss 50mm f/0.7 , the fastest lens in film history. Beyond the expense, these lenses have limited application due to the correspondingly shallower depth of field (DOF) – the scene must either be shallow, shot from a distance, or will be significantly defocused, though this may be the desired effect. Zoom lenses typically have a maximum relative aperture (minimum f-number) of f /2.8 to f /6.3 through their range. High-end lenses will have
384-461: A field stop is a stop intended to cut out light that would be outside the desired field of view and might cause flare or other problems if not stopped. In photography, stops are also a unit used to quantify ratios of light or exposure, with each added stop meaning a factor of two, and each subtracted stop meaning a factor of one-half. The one-stop unit is also known as the EV ( exposure value ) unit. On
512-445: A lens's focal length were 100 mm and its entrance pupil's diameter were 50 mm , the f-number would be 2. This would be expressed as " f /2 " in a lens system. The aperture diameter would be equal to f /2 . Camera lenses often include an adjustable diaphragm , which changes the size of the aperture stop and thus the entrance pupil size. This allows the user to vary the f-number as needed. The entrance pupil diameter
640-484: A simple convex lens will suffice, in practice a compound lens made up of a number of optical lens elements is required to correct (as much as possible) the many optical aberrations that arise. Some aberrations will be present in any lens system. It is the job of the lens designer to balance these and produce a design that is suitable for photographic use and possibly mass production. Typical rectilinear lenses can be thought of as "improved" pinhole "lenses" . As shown,
768-457: A T-stop of 2.3: T = 2.0 0.75 = 2.309... {\displaystyle T={\frac {2.0}{\sqrt {0.75}}}=2.309...} Since real lenses have transmittances of less than 100%, a lens's T-stop number is always greater than its f-number. With 8% loss per air-glass surface on lenses without coating, multicoating of lenses is the key in lens design to decrease transmittance losses of lenses. Some reviews of lenses do measure
896-475: A UV coating to keep out the ultraviolet light that could taint color. Most modern optical cements for bonding glass elements also block UV light, negating the need for a UV filter. However, this leaves an avenue for lens fungus to attack if lenses are not cared for appropriately. UV photographers must go to great lengths to find lenses with no cement or coatings. A lens will most often have an aperture adjustment mechanism, usually an iris diaphragm , to regulate
1024-448: A brightly lit place to 8 mm ( f /2.1 ) in the dark as part of adaptation . In rare cases in some individuals are able to dilate their pupils even beyond 8 mm (in scotopic lighting, close to the physical limit of the iris. In humans, the average iris diameter is about 11.5 mm, which naturally influences the maximal size of the pupil as well, where larger iris diameters would typically have pupils which are able to dilate to
1152-411: A camera, the aperture setting is traditionally adjusted in discrete steps, known as f-stops . Each " stop " is marked with its corresponding f-number, and represents a halving of the light intensity from the previous stop. This corresponds to a decrease of the pupil and aperture diameters by a factor of 1/ √ 2 or about 0.7071, and hence a halving of the area of the pupil. Most modern lenses use
1280-554: A certain point, there is no further sharpness benefit to stopping down, and the diffraction occurred at the edges of the aperture begins to become significant for imaging quality. There is accordingly a sweet spot, generally in the f /4 – f /8 range, depending on lens, where sharpness is optimal, though some lenses are designed to perform optimally when wide open. How significant this varies between lenses, and opinions differ on how much practical impact this has. While optimal aperture can be determined mechanically, how much sharpness
1408-423: A constant aperture, such as f /2.8 or f /4 , which means that the relative aperture will stay the same throughout the zoom range. A more typical consumer zoom will have a variable maximum relative aperture since it is harder and more expensive to keep the maximum relative aperture proportional to the focal length at long focal lengths; f /3.5 to f /5.6 is an example of a common variable aperture range in
SECTION 10
#17327806699651536-594: A consumer zoom lens. By contrast, the minimum aperture does not depend on the focal length – it is limited by how narrowly the aperture closes, not the lens design – and is instead generally chosen based on practicality: very small apertures have lower sharpness due to diffraction at aperture edges, while the added depth of field is not generally useful, and thus there is generally little benefit in using such apertures. Accordingly, DSLR lens typically have minimum aperture of f /16 , f /22 , or f /32 , while large format may go down to f /64 , as reflected in
1664-406: A doublet (two elements) will often suffice. Some older cameras were fitted with convertible lenses (German: Satzobjektiv ) of normal focal length. The front element could be unscrewed, leaving a lens of twice the focal length, and half the angle of view and half the aperture. The simpler half-lens was of adequate quality for the narrow angle of view and small relative aperture. This would require
1792-458: A doubling of sensitivity is represented by a doubling of the number, and a logarithmic number. In the ISO system, a 3° increase in the logarithmic number corresponds to a doubling of sensitivity. Doubling or halving the sensitivity is equal to a difference of one T-stop in terms of light transmittance. Most electronic cameras allow to amplify the signal coming from the pickup element. This amplification
1920-465: A factor of four. A 200 mm focal length f /4 lens has an entrance pupil diameter of 50 mm . The 200 mm lens's entrance pupil has four times the area of the 100 mm f /4 lens's entrance pupil, and thus collects four times as much light from each object in the lens's field of view. But compared to the 100 mm lens, the 200 mm lens projects an image of each object twice as high and twice as wide, covering four times
2048-498: A feature extended to their E-type range in 2013. Optimal aperture depends both on optics (the depth of the scene versus diffraction), and on the performance of the lens. Optically, as a lens is stopped down, the defocus blur at the Depth of Field (DOF) limits decreases but diffraction blur increases. The presence of these two opposing factors implies a point at which the combined blur spot is minimized ( Gibson 1975 , 64); at that point,
2176-603: A few conventional differences in their numbers ( 1 ⁄ 15 , 1 ⁄ 30 , and 1 ⁄ 60 second instead of 1 ⁄ 16 , 1 ⁄ 32 , and 1 ⁄ 64 ). In practice the maximum aperture of a lens is often not an integral power of √ 2 (i.e., √ 2 to the power of a whole number), in which case it is usually a half or third stop above or below an integral power of √ 2 . Modern electronically controlled interchangeable lenses, such as those used for SLR cameras, have f-stops specified internally in 1 ⁄ 8 -stop increments, so
2304-404: A few long telephotos , lenses mounted on bellows , and perspective-control and tilt/shift lenses, the mechanical linkage was impractical, and automatic aperture control was not provided. Many such lenses incorporated a feature known as a "preset" aperture, which allows the lens to be set to working aperture and then quickly switched between working aperture and full aperture without looking at
2432-435: A film twice as sensitive, has the same effect on the exposed image. For all practical purposes extreme accuracy is not required (mechanical shutter speeds were notoriously inaccurate as wear and lubrication varied, with no effect on exposure). It is not significant that aperture areas and shutter speeds do not vary by a factor of precisely two. Photographers sometimes express other exposure ratios in terms of 'stops'. Ignoring
2560-599: A floating system; and Hasselblad and Mamiya call it FLE (floating lens element). Glass is the most common material used to construct lens elements, due to its good optical properties and resistance to scratching. Other materials are also used, such as quartz glass , fluorite , plastics like acrylic (Plexiglass), and even germanium and meteoritic glass . Plastics allow the manufacturing of strongly aspherical lens elements which are difficult or impossible to manufacture in glass, and which simplify or improve lens manufacturing and performance. Plastics are not used for
2688-443: A greater aperture which allows more light to reach the film or image sensor. The photography term "one f-stop" refers to a factor of √ 2 (approx. 1.41) change in f-number which corresponds to a √ 2 change in aperture diameter, which in turn corresponds to a factor of 2 change in light intensity (by a factor 2 change in the aperture area). Aperture priority is a semi-automatic shooting mode used in cameras. It permits
SECTION 20
#17327806699652816-581: A half stop ( 1 ⁄ 2 EV) series would be ( 2 ) 0 2 , ( 2 ) 1 2 , ( 2 ) 2 2 , ( 2 ) 3 2 , ( 2 ) 4 2 , … {\displaystyle ({\sqrt {2}})^{\frac {0}{2}},\ ({\sqrt {2}})^{\frac {1}{2}},\ ({\sqrt {2}})^{\frac {2}{2}},\ ({\sqrt {2}})^{\frac {3}{2}},\ ({\sqrt {2}})^{\frac {4}{2}},\ \ldots } The steps in
2944-526: A half-stop or a one-third-stop system; sometimes f /1.3 and f /3.2 and other differences are used for the one-third stop scale. An H-stop (for hole, by convention written with capital letter H) is an f-number equivalent for effective exposure based on the area covered by the holes in the diffusion discs or sieve aperture found in Rodenstock Imagon lenses. A T-stop (for transmission stops, by convention written with capital letter T)
3072-409: A larger relative aperture and more light entering the system, while a higher f-number means a smaller relative aperture and less light entering the system. The f-number is related to the numerical aperture (NA) of the system, which measures the range of angles over which light can enter or exit the system. The numerical aperture takes into account the refractive index of the medium in which the system
3200-456: A lens used for large format photography. Thus the optical elements built into the lens can be far smaller and cheaper. In exceptional circumstances lenses can have even wider apertures with f-numbers smaller than 1.0; see lens speed: fast lenses for a detailed list. For instance, both the current Leica Noctilux-M 50mm ASPH and a 1960s-era Canon 50mm rangefinder lens have a maximum aperture of f /0.95 . Cheaper alternatives began appearing in
3328-558: A lower f-number is "opening up" the lens. Selecting a higher f-number is "closing" or "stopping down" the lens. Depth of field increases with f-number, as illustrated in the image here. This means that photographs taken with a low f-number (large aperture) will tend to have subjects at one distance in focus, with the rest of the image (nearer and farther elements) out of focus. This is frequently used for nature photography and portraiture because background blur (the aesthetic quality known as ' bokeh ') can be aesthetically pleasing and puts
3456-509: A mechanical pushbutton that sets working aperture when pressed and restores full aperture when pressed a second time. Canon EF lenses, introduced in 1987, have electromagnetic diaphragms, eliminating the need for a mechanical linkage between the camera and the lens, and allowing automatic aperture control with the Canon TS-E tilt/shift lenses. Nikon PC-E perspective-control lenses, introduced in 2008, also have electromagnetic diaphragms,
3584-417: A part in the depth of field in an image. An aperture's f-number is not modified by the camera's sensor size because it is a ratio that only pertains to the attributes of the lens. Instead, the higher crop factor that comes as a result of a smaller sensor size means that, in order to get an equal framing of the subject, the photo must be taken from further away, which results in a less blurry background, changing
3712-406: A photographic lens may have one or more field stops , which limit the system's field of view . When the field of view is limited by a field stop in the lens (rather than at the film or sensor) vignetting results; this is only a problem if the resulting field of view is less than was desired. In astronomy, the opening diameter of the aperture stop (called the aperture ) is a critical parameter in
3840-400: A pinhole "lens" is simply a small aperture that blocks most rays of light, ideally selecting one ray to the object for each point on the image sensor. Pinhole lenses have a few severe limitations: Practical lenses can be thought of as an answer to the question: "how can a pinhole lens be modified to admit more light and give a smaller spot size?". A first step is to put a simple convex lens at
3968-545: A result, smaller formats will have a deeper field than larger formats at the same f-number for the same distance of focus and same angle of view since a smaller format requires a shorter focal length (wider angle lens) to produce the same angle of view, and depth of field increases with shorter focal lengths. Therefore, reduced–depth-of-field effects will require smaller f-numbers (and thus potentially more difficult or complex optics) when using small-format cameras than when using larger-format cameras. Beyond focus, image sharpness
f-number - Misplaced Pages Continue
4096-436: A simple pinhole lens, but rather than being illuminated by single rays of light, each image point is illuminated by a focused "pencil" of light rays . From the front of the camera, the small hole (the aperture), would be seen. The virtual image of the aperture as seen from the world is known as the lens's entrance pupil ; ideally, all rays of light leaving a point on the object that enter the entrance pupil will be focused to
4224-439: A slower lens) f /2.8 – f /5.6 , f /5.6 – f /11 , and f /11 – f /22 . These are not sharp divisions, and ranges for specific lenses vary. The specifications for a given lens typically include the maximum and minimum aperture (opening) sizes, for example, f /0.95 – f /22 . In this case, f /0.95 is currently the maximum aperture (the widest opening on a full-frame format for practical use ), and f /22
4352-431: A standard f-stop scale, which is an approximately geometric sequence of numbers that corresponds to the sequence of the powers of the square root of 2 : f /1 , f /1.4 , f /2 , f /2.8 , f /4 , f /5.6 , f /8 , f /11 , f /16 , f /22 , f /32 , f /45 , f /64 , f /90 , f /128 , etc. Each element in the sequence is one stop lower than the element to its left, and one stop higher than
4480-575: A third stop ( 1 ⁄ 3 EV) series would be ( 2 ) 0 3 , ( 2 ) 1 3 , ( 2 ) 2 3 , ( 2 ) 3 3 , ( 2 ) 4 3 , … {\displaystyle ({\sqrt {2}})^{\frac {0}{3}},\ ({\sqrt {2}})^{\frac {1}{3}},\ ({\sqrt {2}})^{\frac {2}{3}},\ ({\sqrt {2}})^{\frac {3}{3}},\ ({\sqrt {2}})^{\frac {4}{3}},\ \ldots } As in
4608-400: A very large final image viewed at normal distance, or a portion of an image enlarged to normal size ( Hansma 1996 ). Hansma also suggests that the final-image size may not be known when a photograph is taken, and obtaining the maximum practicable sharpness allows the decision to make a large final image to be made at a later time; see also critical sharpness . In many living optical systems ,
4736-405: A wider extreme than those with smaller irises. Maximum dilated pupil size also decreases with age. The iris controls the size of the pupil via two complementary sets muscles, the sphincter and dilator muscles, which are innervated by the parasympathetic and sympathetic nervous systems respectively, and act to induce pupillary constriction and dilation respectively. The state of the pupil
4864-412: A wider field of view than longer focal length lenses. A wider aperture, identified by a smaller f-number, allows using a faster shutter speed for the same exposure. The camera equation , or G#, is the ratio of the radiance reaching the camera sensor to the irradiance on the focal plane of the camera lens. The maximum usable aperture of a lens is specified as the focal ratio or f-number , defined as
4992-427: Is dimensionless and is usually expressed using a lower-case hooked f with the format f / N , where N is the f-number. The f-number is also known as the inverse relative aperture , because it is the inverse of the relative aperture , defined as the aperture diameter divided by focal length. The relative aperture indicates how much light can pass through the lens at a given focal length. A lower f-number means
5120-422: Is required depends on how the image will be used – if the final image is viewed under normal conditions (e.g., an 8″×10″ image viewed at 10″), it may suffice to determine the f -number using criteria for minimum required sharpness, and there may be no practical benefit from further reducing the size of the blur spot. But this may not be true if the final image is viewed under more demanding conditions, e.g.,
5248-538: Is an f-number adjusted to account for light transmission efficiency ( transmittance ). A lens with a T-stop of N projects an image of the same brightness as an ideal lens with 100% transmittance and an f-number of N . A particular lens's T-stop, T , is given by dividing the f-number by the square root of the transmittance of that lens: T = N transmittance . {\displaystyle T={\frac {N}{\sqrt {\text{transmittance}}}}.} For example, an f /2.0 lens with transmittance of 75% has
f-number - Misplaced Pages Continue
5376-516: Is an important element in most optical designs. Its most obvious feature is that it limits the amount of light that can reach the image/ film plane . This can be either unavoidable due to the practical limit of the aperture stop size, or deliberate to prevent saturation of a detector or overexposure of film. In both cases, the size of the aperture stop determines the amount of light admitted by an optical system. The aperture stop also affects other optical system properties: In addition to an aperture stop,
5504-630: Is believed to be the Carl Zeiss Planar 50mm f/0.7 , which was designed and made specifically for the NASA Apollo lunar program to capture the far side of the Moon in 1966. Three of these lenses were purchased by filmmaker Stanley Kubrick in order to film scenes in his 1975 film Barry Lyndon , using candlelight as the sole light source. The complexity of a lens — the number of elements and their degree of asphericity — depends upon
5632-519: Is closely influenced by various factors, primarily light (or absence of light), but also by emotional state, interest in the subject of attention, arousal , sexual stimulation , physical activity, accommodation state, and cognitive load . The field of view is not affected by the size of the pupil. Some individuals are also able to directly exert manual and conscious control over their iris muscles and hence are able to voluntarily constrict and dilate their pupils on command. However, this ability
5760-439: Is generally used to image close-up very small subjects. A macro lens may be of any focal length, the actual focus length being determined by its practical use, considering magnification, the required ratio, access to the subject, and illumination considerations. It can be a special lens corrected optically for close up work or it can be any lens modified (with adapters or spacers, which are also known as "extension tubes".) to bring
5888-502: Is made possible by an error correction system which includes secondary and tertiary mirrors, a three element refractive system and active mounting and optics. The camera equation, or G#, is the ratio of the radiance reaching the camera sensor to the irradiance on the focal plane of the camera lens : G # = 1 + 4 N 2 τ π , {\displaystyle G\#={\frac {1+4N^{2}}{\tau \pi }}\,,} where τ
6016-408: Is not necessarily equal to the aperture stop diameter, because of the magnifying effect of lens elements in front of the aperture. Ignoring differences in light transmission efficiency, a lens with a greater f-number projects darker images. The brightness of the projected image ( illuminance ) relative to the brightness of the scene in the lens's field of view ( luminance ) decreases with the square of
6144-566: Is not true that all lenses with plastic elements are of low photographic quality. The 1951 USAF resolution test chart is one way to measure the resolving power of a lens. The quality of the material, coatings, and build affect the resolution. Lens resolution is ultimately limited by diffraction , and very few photographic lenses approach this resolution. Ones that do are called "diffraction limited" and are usually extremely expensive. Today, most lenses are multi-coated in order to minimize lens flare and other unwanted effects. Some lenses have
6272-457: Is rare and potential use or advantages are unclear. In digital photography, the 35mm-equivalent aperture range is sometimes considered to be more important than the actual f-number. Equivalent aperture is the f-number adjusted to correspond to the f-number of the same size absolute aperture diameter on a lens with a 35mm equivalent focal length . Smaller equivalent f-numbers are expected to lead to higher image quality based on more total light from
6400-442: Is related to f-number through two different optical effects: aberration , due to imperfect lens design, and diffraction which is due to the wave nature of light. The blur-optimal f-stop varies with the lens design. For modern standard lenses having 6 or 7 elements, the sharpest image is often obtained around f /5.6 – f /8 , while for older standard lenses having only 4 elements ( Tessar formula ) stopping to f /11 will give
6528-405: Is the different distances from which a subject can be framed, resulting in a different perspective . Photographs can be taken of a person stretching out a hand with a wideangle, a normal lens, and a telephoto, which contain exactly the same image size by changing the distance from the subject. But the perspective will be different. With the wideangle, the hands will be exaggeratedly large relative to
SECTION 50
#17327806699656656-431: Is the minimum aperture (the smallest opening). The maximum aperture tends to be of most interest and is always included when describing a lens. This value is also known as the lens "speed" , as it affects the exposure time. As the aperture area is proportional to the light admitted by a lens or an optical system, the aperture diameter is proportional to the square root of the light admitted, and thus inversely proportional to
6784-505: Is the transmission coefficient of the lens, and the units are in inverse steradians (sr). Camera lens There is no major difference in principle between a lens used for a still camera , a video camera , a telescope , a microscope , or other apparatus, but the details of design and construction are different. A lens might be permanently fixed to a camera, or it might be interchangeable with lenses of different focal lengths , apertures , and other properties. While in principle
6912-414: Is typically the edges of the objective lens or mirror (or of the mount that holds it). One then speaks of a telescope as having, for example, a 100-centimetre (39 in) aperture. The aperture stop is not necessarily the smallest stop in the system. Magnification and demagnification by lenses and other elements can cause a relatively large stop to be the aperture stop for the system. In astrophotography ,
7040-429: Is usually called gain and is measured in decibels. Every 6 dB of gain is equivalent to one T-stop in terms of light transmittance. Many camcorders have a unified control over the lens f-number and gain. In this case, starting from zero gain and fully open iris, one can either increase f-number by reducing the iris size while gain remains zero, or one can increase gain while iris remains fully open. An example of
7168-445: Is working, while the f-number does not. The f-number N is given by: N = f D {\displaystyle N={\frac {f}{D}}\ } where f is the focal length , and D is the diameter of the entrance pupil ( effective aperture ). It is customary to write f-numbers preceded by " f / ", which forms a mathematical expression of the entrance pupil's diameter in terms of f and N . For example, if
7296-471: The f -number is optimal for image sharpness, for this given depth of field – a wider aperture (lower f -number) causes more defocus, while a narrower aperture (higher f -number) causes more diffraction. As a matter of performance, lenses often do not perform optimally when fully opened, and thus generally have better sharpness when stopped down some – this is sharpness in the plane of critical focus , setting aside issues of depth of field. Beyond
7424-470: The Box Brownie 's meniscus lens, to over 20 in the more complex zooms. These elements may themselves comprise a group of lenses cemented together. The front element is critical to the performance of the whole assembly. In all modern lenses the surface is coated to reduce abrasion, flare , and surface reflectance , and to adjust color balance. To minimize aberration, the curvature is usually set so that
7552-468: The Graflex large format reflex camera an automatic aperture control, not all early 35mm single lens reflex cameras had the feature. With a small aperture, this darkened the viewfinder, making viewing, focusing, and composition difficult. Korling's design enabled full-aperture viewing for accurate focus, closing to the pre-selected aperture opening when the shutter was fired and simultaneously synchronising
7680-555: The Pentax K mount are found across multiple brands, but this is not common today. A few mount designs, such as the Olympus/Kodak Four Thirds System mount for DSLRs, have also been licensed to other makers. Most large-format cameras take interchangeable lenses as well, which are usually mounted in a lensboard or on the front standard. The most common interchangeable lens mounts on the market today include
7808-503: The Pentax Spotmatic ) required that the lens be stopped down to the working aperture when taking a meter reading. Subsequent models soon incorporated mechanical coupling between the lens and the camera body, indicating the working aperture to the camera for exposure while allowing the lens to be at its maximum aperture for composition and focusing; this feature became known as open-aperture metering . For some lenses, including
SECTION 60
#17327806699657936-513: The angle of incidence and the angle of refraction are equal. In a prime lens this is easy, but in a zoom there is always a compromise. The lens usually is focused by adjusting the distance from the lens assembly to the image plane, or by moving elements of the lens assembly. To improve performance, some lenses have a cam system that adjusts the distance between the groups as the lens is focused. Manufacturers call this different things: Nikon calls it CRC (close range correction); Canon calls it
8064-515: The bellows had to be extended to twice the normal length. Good-quality lenses with maximum aperture no greater than f/2.8 and fixed, normal, focal length need at least three (triplet) or four elements (the trade name " Tessar " derives from the Greek tessera , meaning "four"). The widest-range zooms often have fifteen or more. The reflection of light at each of the many interfaces between different optical media (air, glass, plastic) seriously degraded
8192-679: The contrast and color saturation of early lenses, particularly zoom lenses, especially where the lens was directly illuminated by a light source. The introduction many years ago of optical coatings, and advances in coating technology over the years, have resulted in major improvements, and modern high-quality zoom lenses give images of quite acceptable contrast, although zoom lenses with many elements will transmit less light than lenses made with fewer elements (all other factors such as aperture, focal length, and coatings being equal). Many single-lens reflex cameras and some rangefinder cameras have detachable lenses. A few other types do as well, notably
8320-479: The field of view of the instrument and the scale of the image that is presented at the focal plane to an eyepiece , film plate, or CCD . For example, the SOAR 4-meter telescope has a small field of view (about f /16 ) which is useful for stellar studies. The LSST 8.4 m telescope, which will cover the entire sky every three days, has a very large field of view. Its short 10.3 m focal length ( f /1.2 )
8448-455: The iris of the eye – it controls the effective diameter of the lens opening (called pupil in the eyes). Reducing the aperture size (increasing the f-number) provides less light to sensor and also increases the depth of field (by limiting the angle of cone of image light reaching the sensor), which describes the extent to which subject matter lying closer than or farther from the actual plane of focus appears to be in focus. In general,
8576-759: The Canon EF , EF-S and EF-M autofocus lens mounts. Others include the Nikon F manual and autofocus mounts, the Olympus / Kodak Four Thirds and Olympus/Panasonic Micro Four Thirds digital-only mounts, the Pentax K mount and autofocus variants, the Sony Alpha mount (derived from the Minolta mount) and the Sony E digital-only mount. A macro lens used in macro or "close-up" photography (not to be confused with
8704-490: The Mamiya TLR cameras and SLR, medium format cameras ( RZ67 , RB67 , 645-1000s)other companies that produce medium format equipment such as Bronica, Hasselblad and Fuji have similar camera styles that allow interchangeability in the lenses as well, and mirrorless interchangeable-lens cameras . The lenses attach to the camera using a lens mount , which contains mechanical linkages and often also electrical contacts between
8832-593: The T-stop or transmission rate in their benchmarks. T-stops are sometimes used instead of f-numbers to more accurately determine exposure, particularly when using external light meters . Lens transmittances of 60%–95% are typical. T-stops are often used in cinematography, where many images are seen in rapid succession and even small changes in exposure will be noticeable. Cinema camera lenses are typically calibrated in T-stops instead of f-numbers. In still photography, without
8960-425: The amount of light that passes. In early camera models a rotating plate or slider with different sized holes was used. These Waterhouse stops may still be found on modern, specialized lenses. A shutter , to regulate the time during which light may pass, may be incorporated within the lens assembly (for better quality imagery), within the camera, or even, rarely, in front of the lens. Some cameras with leaf shutters in
9088-415: The angle of view, the maximum aperture, and intended price point, among other variables. An extreme wideangle lens of large aperture must be of very complex construction to correct for optical aberrations, which are worse at the edge of the field and when the edge of a large lens is used for image-forming. A long-focus lens of small aperture can be of very simple construction to attain comparable image quality:
9216-424: The aperture control. A typical operation might be to establish rough composition, set the working aperture for metering, return to full aperture for a final check of focus and composition, and focusing, and finally, return to working aperture just before exposure. Although slightly easier than stopped-down metering, operation is less convenient than automatic operation. Preset aperture controls have taken several forms;
9344-416: The aperture may be given as a linear measure (for example, in inches or millimetres) or as the dimensionless ratio between that measure and the focal length . In other photography, it is usually given as a ratio. A usual expectation is that the term aperture refers to the opening of the aperture stop, but in reality, the term aperture and the aperture stop are mixed in use. Sometimes even stops that are not
9472-465: The aperture open until the instant of exposure to allow SLR cameras to focus with a brighter image with shallower depth of field, theoretically allowing better focus accuracy. Focal lengths are usually specified in millimetres (mm), but older lenses might be marked in centimetres (cm) or inches. For a given film or sensor size, specified by the length of the diagonal, a lens may be classified as a: A side effect of using lenses of different focal lengths
9600-407: The aperture scale usually had a click stop at every whole and half stop. On modern cameras, especially when aperture is set on the camera body, f-number is often divided more finely than steps of one stop. Steps of one-third stop ( 1 ⁄ 3 EV) are the most common, since this matches the ISO system of film speeds . Half-stop steps are used on some cameras. Usually the full stops are marked, and
9728-429: The aperture size will regulate the film's or image sensor's degree of exposure to light. Typically, a fast shutter will require a larger aperture to ensure sufficient light exposure, and a slow shutter will require a smaller aperture to avoid excessive exposure. A device called a diaphragm usually serves as the aperture stop and controls the aperture (the opening of the aperture stop). The diaphragm functions much like
9856-426: The aperture stop of an optical system are also called apertures. Contexts need to clarify these terms. The word aperture is also used in other contexts to indicate a system which blocks off light outside a certain region. In astronomy, for example, a photometric aperture around a star usually corresponds to a circular window around the image of a star within which the light intensity is assumed. The aperture stop
9984-436: The aperture, but in general these three will be in different places. Practical photographic lenses include more lens elements. The additional elements allow lens designers to reduce various aberrations, but the principle of operation remains the same: pencils of rays are collected at the entrance pupil and focused down from the exit pupil onto the image plane. A camera lens may be made from a number of elements: from one, as in
10112-445: The area of the entrance pupil that is the object space-side image of the aperture of the system, equal to: Where the two equivalent forms are related via the f-number N = f / D , with focal length f and entrance pupil diameter D . The focal length value is not required when comparing two lenses of the same focal length; a value of 1 can be used instead, and the other factors can be dropped as well, leaving area proportion to
10240-414: The area, and so both lenses produce the same illuminance at the focal plane when imaging a scene of a given luminance. The word stop is sometimes confusing due to its multiple meanings. A stop can be a physical object: an opaque part of an optical system that blocks certain rays. The aperture stop is the aperture setting that limits the brightness of the image by restricting the input pupil size, while
10368-597: The barrel or pressing a button which activates an electric motor . Commonly, the lens may zoom from moderate wide-angle, through normal, to moderate telephoto; or from normal to extreme telephoto. The zoom range is limited by manufacturing constraints; the ideal of a lens of large maximum aperture which will zoom from extreme wideangle to extreme telephoto is not attainable. Zoom lenses are widely used for small-format cameras of all types: still and cine cameras with fixed or interchangeable lenses. Bulk and price limit their use for larger film sizes. Motorized zoom lenses may also have
10496-431: The cameras' 1 ⁄ 3 -stop settings are approximated by the nearest 1 ⁄ 8 -stop setting in the lens. Including aperture value AV: N = 2 AV {\displaystyle N={\sqrt {2^{\text{AV}}}}} Conventional and calculated f-numbers, full-stop series: Sometimes the same number is included on several scales; for example, an aperture of f /1.2 may be used in either
10624-422: The changed depth of field, nor the perceived change in light sensitivity are a result of the aperture. Instead, equivalent aperture can be seen as a rule of thumb to judge how changes in sensor size might affect an image, even if qualities like pixel density and distance from the subject are the actual causes of changes in the image. The terms scanning aperture and sampling aperture are often used to refer to
10752-407: The common 35 mm film format in general production have apertures of f /1.2 or f /1.4 , with more at f /1.8 and f /2.0 , and many at f /2.8 or slower; f /1.0 is unusual, though sees some use. When comparing "fast" lenses, the image format used must be considered. Lenses designed for a small format such as half frame or APS-C need to project a much smaller image circle than
10880-453: The compositional term close up ) is any lens that produces an image on the focal plane (i.e., film or a digital sensor) that is one quarter of life size (1:4) to the same size (1:1) as the subject being imaged. There is no official standard to define a macro lens, usually a prime lens , but a 1:1 ratio is, typically, considered "true" macro. Magnification from life size to larger is called "Micro" photography (2:1, 3:1 etc.). This configuration
11008-403: The cone angle of a bundle of rays that comes to a focus in the image plane . An optical system typically has many openings or structures that limit ray bundles (ray bundles are also known as pencils of light). These structures may be the edge of a lens or mirror , or a ring or other fixture that holds an optical element in place or may be a special element such as a diaphragm placed in
11136-604: The design of a telescope . Generally, one would want the aperture to be as large as possible, to collect the maximum amount of light from the distant objects being imaged. The size of the aperture is limited, however, in practice by considerations of its manufacturing cost and time and its weight, as well as prevention of aberrations (as mentioned above). Apertures are also used in laser energy control, close aperture z-scan technique , diffractions/patterns, and beam cleaning. Laser applications include spatial filters , Q-switching , high intensity x-ray control. In light microscopy,
11264-405: The diameter of an aperture stop in the system: N = f D → × D f = N D {\displaystyle N={\frac {f}{D}}\quad {\xrightarrow {\times D}}\quad f=ND} Even though the principles of focal ratio are always the same, the application to which the principle is put can differ. In photography the focal ratio varies
11392-1116: The earlier DIN and ASA film-speed standards, the ISO speed is defined only in one-third stop increments, and shutter speeds of digital cameras are commonly on the same scale in reciprocal seconds. A portion of the ISO range is the sequence … 16 / 13 ∘ , 20 / 14 ∘ , 25 / 15 ∘ , 32 / 16 ∘ , 40 / 17 ∘ , 50 / 18 ∘ , 64 / 19 ∘ , 80 / 20 ∘ , 100 / 21 ∘ , 125 / 22 ∘ , … {\displaystyle \ldots 16/13^{\circ },\ 20/14^{\circ },\ 25/15^{\circ },\ 32/16^{\circ },\ 40/17^{\circ },\ 50/18^{\circ },\ 64/19^{\circ },\ 80/20^{\circ },\ 100/21^{\circ },\ 125/22^{\circ },\ \ldots } while shutter speeds in reciprocal seconds have
11520-647: The early 2010s, such as the Cosina Voigtländer f /0.95 Nokton (several in the 10.5–60 mm range) and f /0.8 ( 29 mm ) Super Nokton manual focus lenses in the for the Micro Four-Thirds System , and the Venus Optics (Laowa) Argus 35 mm f /0.95 . Professional lenses for some movie cameras have f-numbers as small as f /0.75 . Stanley Kubrick 's film Barry Lyndon has scenes shot by candlelight with
11648-415: The edges for large apertures. Photojournalists have a saying, " f /8 and be there ", meaning that being on the scene is more important than worrying about technical details. Practically, f /8 (in 35 mm and larger formats) allows adequate depth of field and sufficient lens speed for a decent base exposure in most daylight situations. Computing the f-number of the human eye involves computing
11776-833: The element to its right. The values of the ratios are rounded off to these particular conventional numbers, to make them easier to remember and write down. The sequence above is obtained by approximating the following exact geometric sequence: f / 1 = f ( 2 ) 0 , f / 1.4 = f ( 2 ) 1 , f / 2 = f ( 2 ) 2 , f / 2.8 = f ( 2 ) 3 , … {\displaystyle f/1={\frac {f}{({\sqrt {2}})^{0}}},\ f/1.4={\frac {f}{({\sqrt {2}})^{1}}},\ f/2={\frac {f}{({\sqrt {2}})^{2}}},\ f/2.8={\frac {f}{({\sqrt {2}})^{3}}},\ \ldots } In
11904-504: The eye consists of an iris which adjusts the size of the pupil , through which light enters. The iris is analogous to the diaphragm, and the pupil (which is the adjustable opening in the iris) the aperture. Refraction in the cornea causes the effective aperture (the entrance pupil in optics parlance) to differ slightly from the physical pupil diameter. The entrance pupil is typically about 4 mm in diameter, although it can range from as narrow as 2 mm ( f /8.3 ) in diameter in
12032-403: The f-number markings, the f-stops make a logarithmic scale of exposure intensity. Given this interpretation, one can then think of taking a half-step along this scale, to make an exposure difference of a "half stop". Most twentieth-century cameras had a continuously variable aperture, using an iris diaphragm , with each full stop marked. Click-stopped aperture came into common use in the 1960s;
12160-435: The f-number. A 100 mm focal length f /4 lens has an entrance pupil diameter of 25 mm . A 100 mm focal length f /2 lens has an entrance pupil diameter of 50 mm . Since the area is proportional to the square of the pupil diameter, the amount of light admitted by the f /2 lens is four times that of the f /4 lens. To obtain the same photographic exposure , the exposure time must be reduced by
12288-609: The firing of a flash unit. From 1956 SLR camera manufacturers separately developed automatic aperture control (the Miranda T 'Pressure Automatic Diaphragm', and other solutions on the Exakta Varex IIa and Praktica FX2 ) allowing viewing at the lens's maximum aperture, stopping the lens down to the working aperture at the moment of exposure, and returning the lens to maximum aperture afterward. The first SLR cameras with internal ( "through-the-lens" or "TTL" ) meters (e.g.,
12416-400: The focal plane "forward" for very close photography. Depending on the camera to subject distance and aperture, the depth-of-field can be very narrow, limiting the linear depth of the area that will be in focus. Lenses are usually stopped down to give a greater depth-of-field. Some lenses, called zoom lenses , have a focal length that varies as internal elements are moved, typically by rotating
12544-413: The focal-plane illuminance (or optical power per unit area in the image) and is used to control variables such as depth of field . When using an optical telescope in astronomy, there is no depth of field issue, and the brightness of stellar point sources in terms of total optical power (not divided by area) is a function of absolute aperture area only, independent of focal length. The focal length controls
12672-443: The focus, iris, and other functions motorized. Some notable photographic optical lens designs are: Aperture stop In optics , the aperture of an optical system (including a system consisted of a single lens) is a hole or an opening that primarily limits light propagated through the system. More specifically, the entrance pupil as the front side image of the aperture and focal length of an optical system determine
12800-479: The head. As the focal length increases, the emphasis on the outstretched hand decreases. However, if pictures are taken from the same distance, and enlarged and cropped to contain the same view, the pictures will have identical perspective. A moderate long-focus (telephoto) lens is often recommended for portraiture because the perspective corresponding to the longer shooting distance is considered to look more flattering. The widest aperture lens in history of photography
12928-592: The intermediate positions click but are not marked. As an example, the aperture that is one-third stop smaller than f /2.8 is f /3.2 , two-thirds smaller is f /3.5 , and one whole stop smaller is f /4 . The next few f-stops in this sequence are: f / 4.5 , f / 5 , f / 5.6 , f / 6.3 , f / 7.1 , f / 8 , … {\displaystyle f/4.5,\ f/5,\ f/5.6,\ f/6.3,\ f/7.1,\ f/8,\ \ldots } To calculate
13056-461: The lens and camera body. The lens mount design is an important issue for compatibility between cameras and lenses. There is no universal standard for lens mounts, and each major camera maker typically uses its own proprietary design, incompatible with other makers. A few older manual focus lens mount designs, such as the Leica M39 lens mount for rangefinders, M42 lens mount for early SLRs, and
13184-421: The lens omit the aperture, and the shutter does double duty. The two fundamental parameters of an optical lens are the focal length and the maximum aperture . The lens' focal length determines the magnification of the image projected onto the image plane, and the aperture the light intensity of that image. For a given photographic system the focal length determines the angle of view , short focal lengths giving
13312-459: The lens's focal length divided by the effective aperture (or entrance pupil ), a dimensionless number. The lower the f-number, the higher light intensity at the focal plane. Larger apertures (smaller f-numbers) provide a much shallower depth of field than smaller apertures, other conditions being equal. Practical lens assemblies may also contain mechanisms to deal with measuring light, secondary apertures for flare reduction, and mechanisms to hold
13440-519: The light-refracting properties of the liquids in the eye be taken into account. Treating the eye as an ordinary air-filled camera and lens results in an incorrect focal length and f-number. In astronomy, the f-number is commonly referred to as the focal ratio (or f-ratio ) notated as N {\displaystyle N} . It is still defined as the focal length f {\displaystyle f} of an objective divided by its diameter D {\displaystyle D} or by
13568-539: The most common has been the use of essentially two lens aperture rings, with one ring setting the aperture and the other serving as a limit stop when switching to working aperture. Examples of lenses with this type of preset aperture control are the Nikon PC Nikkor 28 mm f /3.5 and the SMC Pentax Shift 6×7 75 mm f /4.5 . The Nikon PC Micro-Nikkor 85 mm f /2.8D lens incorporates
13696-462: The name of Group f/64 . Depth of field is a significant concern in macro photography , however, and there one sees smaller apertures. For example, the Canon MP-E 65mm can have effective aperture (due to magnification) as small as f /96 . The pinhole optic for Lensbaby creative lenses has an aperture of just f /177 . The amount of light captured by an optical system is proportional to
13824-411: The need for rigorous consistency of all lenses and cameras used, slight differences in exposure are less important; however, T-stops are still used in some kinds of special-purpose lenses such as Smooth Trans Focus lenses by Minolta and Sony . Photographic film 's and electronic camera sensor's sensitivity to light is often specified using ASA/ISO numbers . Both systems have a linear number where
13952-427: The opening through which an image is sampled, or scanned, for example in a Drum scanner , an image sensor , or a television pickup apparatus. The sampling aperture can be a literal optical aperture, that is, a small opening in space, or it can be a time-domain aperture for sampling a signal waveform. For example, film grain is quantified as graininess via a measurement of film density fluctuations as seen through
14080-553: The optical path to limit the light admitted by the system. In general, these structures are called stops, and the aperture stop is the stop that primarily determines the cone of rays that an optical system accepts (see entrance pupil ). As a result, it also determines the ray cone angle and brightness at the image point (see exit pupil ). The aperture stop generally depends on the object point location; on-axis object points at different object planes may have different aperture stops, and even object points at different lateral locations at
14208-424: The outermost elements of all but the cheapest lenses as they scratch easily. Molded plastic lenses have been used for the cheapest disposable cameras for many years, and have acquired a bad reputation: manufacturers of quality optics tend to use euphemisms such as "optical resin". However many modern, high performance (and high priced) lenses from popular manufacturers include molded or hybrid aspherical elements, so it
14336-421: The perceived depth of field. Similarly, a smaller sensor size with an equivalent aperture will result in a darker image because of the pixel density of smaller sensors with equivalent megapixels. Every photosite on a camera's sensor requires a certain amount of surface area that is not sensitive to light, a factor that results in differences in pixel pitch and changes in the signal-noise ratio . However, neither
14464-577: The photographer to select an aperture setting and let the camera decide the shutter speed and sometimes also ISO sensitivity for the correct exposure. This is also referred to as Aperture Priority Auto Exposure, A mode, AV mode (aperture-value mode), or semi-auto mode. Typical ranges of apertures used in photography are about f /2.8 – f /22 or f /2 – f /16 , covering six stops, which may be divided into wide, middle, and narrow of two stops each, roughly (using round numbers) f /2 – f /4 , f /4 – f /8 , and f /8 – f /16 or (for
14592-402: The physical aperture and focal length of the eye. Typically, the pupil can dilate to be as large as 6–7 mm in darkness, which translates into the maximal physical aperture. Some individuals' pupils can dilate to over 9 mm wide. The f-number of the human eye varies from about f /8.3 in a very brightly lit place to about f /2.1 in the dark. Computing the focal length requires that
14720-411: The pinhole with a focal length equal to the distance to the film plane (assuming the camera will take pictures of distant objects ). This allows the pinhole to be opened up significantly (fourth image) because a thin convex lens bends light rays in proportion to their distance to the axis of the lens, with rays striking the center of the lens passing straight through. The geometry is almost the same as with
14848-540: The reciprocal square of the f-number N . If two cameras of different format sizes and focal lengths have the same angle of view , and the same aperture area, they gather the same amount of light from the scene. In that case, the relative focal-plane illuminance , however, would depend only on the f-number N , so it is less in the camera with the larger format, longer focal length, and higher f-number. This assumes both lenses have identical transmissivity. Though as early as 1933 Torkel Korling had invented and patented for
14976-405: The same object plane may have different aperture stops ( vignetted ). In practice, many object systems are designed to have a single aperture stop at designed working distance and field of view . In some contexts, especially in photography and astronomy , aperture refers to the opening diameter of the aperture stop through which light can pass. For example, in a telescope , the aperture stop
15104-400: The same point on the image sensor/film (provided the object point is in the field of view). If one were inside the camera, one would see the lens acting as a projector . The virtual image of the aperture from inside the camera is the lens's exit pupil . In this simple case, the aperture, entrance pupil, and exit pupil are all in the same place because the only optical element is in the plane of
15232-453: The same way as one f-stop corresponds to a factor of two in light intensity, shutter speeds are arranged so that each setting differs in duration by a factor of approximately two from its neighbour. Opening up a lens by one stop allows twice as much light to fall on the film in a given period of time. Therefore, to have the same exposure at this larger aperture as at the previous aperture, the shutter would be opened for half as long (i.e., twice
15360-436: The sharpest image. The larger number of elements in modern lenses allow the designer to compensate for aberrations, allowing the lens to give better pictures at lower f-numbers. At small apertures, depth of field and aberrations are improved, but diffraction creates more spreading of the light, causing blur. Light falloff is also sensitive to f-stop. Many wide-angle lenses will show a significant light falloff ( vignetting ) at
15488-421: The smaller the aperture (the larger the f-number), the greater the distance from the plane of focus the subject matter may be while still appearing in focus. The lens aperture is usually specified as an f-number , the ratio of focal length to effective aperture diameter (the diameter of the entrance pupil ). A lens typically has a set of marked "f-stops" that the f-number can be set to. A lower f-number denotes
15616-404: The speed). The film will respond equally to these equal amounts of light, since it has the property of reciprocity . This is less true for extremely long or short exposures, where there is reciprocity failure . Aperture, shutter speed, and film sensitivity are linked: for constant scene brightness, doubling the aperture area (one stop), halving the shutter speed (doubling the time open), or using
15744-457: The square root of required exposure time, such that an aperture of f /2 allows for exposure times one quarter that of f /4 . ( f /2 is 4 times larger than f /4 in the aperture area.) Lenses with apertures opening f /2.8 or wider are referred to as "fast" lenses, although the specific point has changed over time (for example, in the early 20th century aperture openings wider than f /6 were considered fast. The fastest lenses for
15872-477: The steps in a full stop (1 EV) one could use ( 2 ) 0 , ( 2 ) 1 , ( 2 ) 2 , ( 2 ) 3 , ( 2 ) 4 , … {\displaystyle ({\sqrt {2}})^{0},\ ({\sqrt {2}})^{1},\ ({\sqrt {2}})^{2},\ ({\sqrt {2}})^{3},\ ({\sqrt {2}})^{4},\ \ldots } The steps in
16000-419: The subject, as well as lead to reduced depth of field. For example, a Sony Cyber-shot DSC-RX10 uses a 1" sensor, 24 – 200 mm with maximum aperture constant along the zoom range; f /2.8 has equivalent aperture range f /7.6 , which is a lower equivalent f-number than some other f /2.8 cameras with smaller sensors. However, modern optical research concludes that sensor size does not actually play
16128-436: The use of f-numbers in photography is the sunny 16 rule : an approximately correct exposure will be obtained on a sunny day by using an aperture of f /16 and the shutter speed closest to the reciprocal of the ISO speed of the film; for example, using ISO 200 film, an aperture of f /16 and a shutter speed of 1 ⁄ 200 second. The f-number may then be adjusted downwards for situations with lower light. Selecting
16256-427: The viewer's focus on the main subject in the foreground. The depth of field of an image produced at a given f-number is dependent on other parameters as well, including the focal length , the subject distance, and the format of the film or sensor used to capture the image. Depth of field can be described as depending on just angle of view, subject distance, and entrance pupil diameter (as in von Rohr's method ). As
16384-455: The word aperture may be used with reference to either the condenser (that changes the angle of light onto the specimen field), field iris (that changes the area of illumination on specimens) or possibly objective lens (forms primary images). See Optical microscope . The aperture stop of a photographic lens can be adjusted to control the amount of light reaching the film or image sensor . In combination with variation of shutter speed ,
#964035