Misplaced Pages

#730269

55-425: VPC may refer to: Science and technology [ edit ] Volts Per Cell , the voltage needed to charge a battery Vapour Phase Chromatography Virtual private cloud , within a public cloud computing network Virtual PortChannel - Cisco MC-LAG technology Others [ edit ] Value of Preventing a Casualty Ventricular premature contraction ,

110-419: A "20-hour" rate), while typical charging and discharging may occur at C/2 (two hours for full capacity). The available capacity of electrochemical cells varies depending on the discharge rate. Some energy is lost in the internal resistance of cell components (plates, electrolyte, interconnections), and the rate of discharge is limited by the speed at which chemicals in the cell can move about. For lead-acid cells,

165-437: A battery charger using AC mains electricity , although some are equipped to use a vehicle's 12-volt DC power outlet. The voltage of the source must be higher than that of the battery to force current to flow into it, but not too much higher or the battery may be damaged. Chargers take from a few minutes to several hours to charge a battery. Slow "dumb" chargers without voltage or temperature-sensing capabilities will charge at

220-621: A battery rather than to operate the radio directly. Flashlights may be driven by a dynamo directly. For transportation, uninterruptible power supply systems and laboratories, flywheel energy storage systems store energy in a spinning rotor for conversion to electric power when needed; such systems may be used to provide large pulses of power that would otherwise be objectionable on a common electrical grid. Ultracapacitors  – capacitors of extremely high value – are also used; an electric screwdriver which charges in 90 seconds and will drive about half as many screws as

275-399: A battery. For some types, the maximum charging rate will be limited by the speed at which active material can diffuse through a liquid electrolyte. High charging rates may produce excess gas in a battery, or may result in damaging side reactions that permanently lower the battery capacity. Very roughly, and with many exceptions and caveats, restoring a battery's full capacity in one hour or less

330-571: A battery. To avoid damage from the cell reversal effect, it is necessary to access each cell separately: each cell is individually discharged by connecting a load clip across the terminals of each cell, thereby avoiding cell reversal. If a multi-cell battery is fully discharged, it will often be damaged due to the cell reversal effect mentioned above. It is possible however to fully discharge a battery without causing cell reversal—either by discharging each cell separately, or by allowing each cell's internal leakage to dissipate its charge over time. Even if

385-466: A cell is brought to a fully discharged state without reversal, however, damage may occur over time simply due to remaining in the discharged state. An example of this is the sulfation that occurs in lead-acid batteries that are left sitting on a shelf for long periods. For this reason it is often recommended to charge a battery that is intended to remain in storage, and to maintain its charge level by periodically recharging it. Since damage may also occur if

440-443: A device using a rechargeable battery was introduced in 2007, and similar flashlights have been produced. In keeping with the concept of ultracapacitors, betavoltaic batteries may be utilized as a method of providing a trickle-charge to a secondary battery, greatly extending the life and energy capacity of the battery system being employed; this type of arrangement is often referred to as a "hybrid betavoltaic power source" by those in

495-428: A discharged cell in this way causes undesirable and irreversible chemical reactions to occur, resulting in permanent damage to the cell. Cell reversal can occur under a number of circumstances, the two most common being: In the latter case, the problem occurs due to the different cells in a battery having slightly different capacities. When one cell reaches discharge level ahead of the rest, the remaining cells will force

550-467: A hybrid lead–acid battery and ultracapacitor invented by Australia's national science organisation CSIRO , exhibits tens of thousands of partial state of charge cycles and has outperformed traditional lead-acid, lithium, and NiMH-based cells when compared in testing in this mode against variability management power profiles. UltraBattery has kW and MW-scale installations in place in Australia, Japan, and

605-537: A hydrogen-absorbing alloy for the negative electrode instead of cadmium . The lithium-ion battery was introduced in the market in 1991, is the choice in most consumer electronics, having the best energy density and a very slow loss of charge when not in use. It does have drawbacks too, particularly the risk of unexpected ignition from the heat generated by the battery. Such incidents are rare and according to experts, they can be minimized "via appropriate design, installation, procedures and layers of safeguards" so

SECTION 10

#1732780185731

660-551: A long and stable lifetime. The effective number of cycles is above 5000 and the battery is not damaged by deep discharge. The energy density is rather low, somewhat lower than lead–acid. A rechargeable battery is only one of several types of rechargeable energy storage systems. Several alternatives to rechargeable batteries exist or are under development. For uses such as portable radios , rechargeable batteries may be replaced by clockwork mechanisms which are wound up by hand, driving dynamos , although this system may be used to charge

715-473: A low rate, typically taking 14 hours or more to reach a full charge. Rapid chargers can typically charge cells in two to five hours, depending on the model, with the fastest taking as little as fifteen minutes. Fast chargers must have multiple ways of detecting when a cell reaches full charge (change in terminal voltage, temperature, etc.) to stop charging before harmful overcharging or overheating occurs. The fastest chargers often incorporate cooling fans to keep

770-888: A much lower total cost of ownership and environmental impact , as they can be recharged inexpensively many times before they need replacing. Some rechargeable battery types are available in the same sizes and voltages as disposable types, and can be used interchangeably with them. Billions of dollars in research are being invested around the world for improving batteries as industry focuses on building better batteries. Devices which use rechargeable batteries include automobile starters , portable consumer devices, light vehicles (such as motorized wheelchairs , golf carts , electric bicycles , and electric forklifts ), road vehicles (cars, vans, trucks, motorbikes), trains, small airplanes, tools, uninterruptible power supplies , and battery storage power stations . Emerging applications in hybrid internal combustion-battery and electric vehicles drive

825-486: A regulated current source that tapers as the battery reaches fully charged voltage. Charging a battery incorrectly can damage a battery; in extreme cases, batteries can overheat, catch fire, or explosively vent their contents. Battery charging and discharging rates are often discussed by referencing a "C" rate of current. The C rate is that which would theoretically fully charge or discharge the battery in one hour. For example, trickle charging might be performed at C/20 (or

880-483: A resistive voltage drop that is greater than the cell's forward emf . This results in the reversal of the cell's polarity while the current is flowing. The higher the required discharge rate of a battery, the better matched the cells should be, both in the type of cell and state of charge, in order to reduce the chances of cell reversal. In some situations, such as when correcting NiCd batteries that have been previously overcharged, it may be desirable to fully discharge

935-540: A terminal voltage that does not decline rapidly until nearly exhausted. This terminal voltage drop complicates the design of power electronics for use with ultracapacitors. However, there are potential benefits in cycle efficiency, lifetime, and weight compared with rechargeable systems. China started using ultracapacitors on two commercial bus routes in 2006; one of them is route 11 in Shanghai . Flow batteries , used for specialized applications, are recharged by replacing

990-976: A type of energy accumulator ), is a type of electrical battery which can be charged, discharged into a load, and recharged many times, as opposed to a disposable or primary battery , which is supplied fully charged and discarded after use. It is composed of one or more electrochemical cells . The term "accumulator" is used as it accumulates and stores energy through a reversible electrochemical reaction . Rechargeable batteries are produced in many different shapes and sizes, ranging from button cells to megawatt systems connected to stabilize an electrical distribution network . Several different combinations of electrode materials and electrolytes are used, including lead–acid , zinc–air , nickel–cadmium (NiCd), nickel–metal hydride (NiMH), lithium-ion (Li-ion), lithium iron phosphate (LiFePO4), and lithium-ion polymer (Li-ion polymer). Rechargeable batteries typically initially cost more than disposable batteries but have

1045-423: A type of abnormal heartbeat Violence Policy Center , US organization advocating firearms control The Voter Participation Center Cartersville Airport , IATA code VP-C, Cayman Islands aircraft registration prefix Topics referred to by the same term [REDACTED] This disambiguation page lists articles associated with the title VPC . If an internal link led you here, you may wish to change

1100-732: A variety of cost of doing business items, for example, ship and re-ship, and opportunity costs, while it also considers incentives developed for an alternative approach. Incentives and other variables include tax credits, common language, expedited delivery, and customer-oriented supplier visits. TCO, when incorporated in any financial benefit analysis, provides a cost basis for determining the total economic value of an investment. Examples include: return on investment , internal rate of return , economic value added , return on information technology, and rapid economic justification. A TCO analysis includes total cost of acquisition and operating costs , as well as costs related to replacement or upgrades at

1155-410: A variety of critical requirements and costs over the life of the building: A key objective of planning, constructing, operating, and managing buildings via TCO principals is for building owners and facility professionals to predict needs and deliver data-driven results.  TCO can be applied any time during the life of a facility asset to manage cost inputs for the life of the structure or system into

SECTION 20

#1732780185731

1210-416: Is a refinement of lithium ion technology by Excellatron. The developers claim a large increase in recharge cycles to around 40,000 and higher charge and discharge rates, at least 5 C charge rate. Sustained 60 C discharge and 1000 C peak discharge rate and a significant increase in specific energy , and energy density. lithium iron phosphate batteries are used in some applications. UltraBattery ,

1265-400: Is already in place for the product. The potassium-ion battery delivers around a million cycles, due to the extraordinary electrochemical stability of potassium insertion/extraction materials such as Prussian blue . The sodium-ion battery is meant for stationary storage and competes with lead–acid batteries. It aims at a low total cost of ownership per kWh of storage. This is achieved by

1320-413: Is considered fast charging. A battery charger system will include more complex control-circuit- and charging strategies for fast charging, than for a charger designed for slower recharging. The active components in a secondary cell are the chemicals that make up the positive and negative active materials, and the electrolyte . The positive and negative electrodes are made up of different materials, with

1375-476: Is easily applicable to the transportation industry and to motor vehicle ownership, for example, the TCO defines the cost of owning an automobile from the time of purchase by the owner, through its operation and maintenance to the time it leaves the possession of the owner. Comparative TCO studies between various models help consumers choose a car to fit their needs and budget. Some of the key elements incorporated in

1430-427: Is no longer available to participate in the next discharge cycle. Sealed batteries may lose moisture from their liquid electrolyte, especially if overcharged or operated at high temperature. This reduces the cycling life. Recharging time is an important parameter to the user of a product powered by rechargeable batteries. Even if the charging power supply provides enough power to operate the device as well as recharge

1485-479: The U.S. It has also been subjected to extensive testing in hybrid electric vehicles and has been shown to last more than 100,000 vehicle miles in on-road commercial testing in a courier vehicle. The technology is claimed to have a lifetime of 7 to 10 times that of conventional lead-acid batteries in high rate partial state-of-charge use, with safety and environmental benefits claimed over competitors like lithium-ion. Its manufacturer suggests an almost 100% recycling rate

1540-527: The battery is not constant during charging and discharging. Some types have relatively constant voltage during discharge over much of their capacity. Non-rechargeable alkaline and zinc–carbon cells output 1.5 V when new, but this voltage drops with use. Most NiMH AA and AAA cells are rated at 1.2 V, but have a flatter discharge curve than alkalines and can usually be used in equipment designed to use alkaline batteries . Battery manufacturers' technical notes often refer to voltage per cell (VPC) for

1595-404: The battery is overcharged, the optimal level of charge during storage is typically around 30% to 70%. Depth of discharge (DOD) is normally stated as a percentage of the nominal ampere-hour capacity; 0% DOD means no discharge. As the usable capacity of a battery system depends on the rate of discharge and the allowable voltage at the end of discharge, the depth of discharge must be qualified to show

1650-457: The battery, the device is attached to an external power supply during the charging time. For electric vehicles used industrially, charging during off-shifts may be acceptable. For highway electric vehicles, rapid charging is necessary for charging in a reasonable time. A rechargeable battery cannot be recharged at an arbitrarily high rate. The internal resistance of the battery will produce heat, and excessive temperature rise will damage or destroy

1705-404: The cells from overheating. Battery packs intended for rapid charging may include a temperature sensor that the charger uses to protect the pack; the sensor will have one or more additional electrical contacts. Different battery chemistries require different charging schemes. For example, some battery types can be safely recharged from a constant voltage source. Other types need to be charged with

VPC - Misplaced Pages Continue

1760-414: The current through the discharged cell. Many battery-operated devices have a low-voltage cutoff that prevents deep discharges from occurring that might cause cell reversal. A smart battery has voltage monitoring circuitry built inside. Cell reversal can occur to a weakly charged cell even before it is fully discharged. If the battery drain current is high enough, the cell's internal resistance can create

1815-660: The day to be used at night). Load-leveling reduces the maximum power which a plant must be able to generate, reducing capital cost and the need for peaking power plants . According to a report from Research and Markets, the analysts forecast the global rechargeable battery market to grow at a CAGR of 8.32% during the period 2018–2022. Small rechargeable batteries can power portable electronic devices , power tools, appliances, and so on. Heavy-duty batteries power electric vehicles , ranging from scooters to locomotives and ships . They are used in distributed electricity generation and in stand-alone power systems . During charging,

1870-450: The electrolyte liquid. A flow battery can be considered to be a type of rechargeable fuel cell . Rechargeable battery research includes development of new electrochemical systems as well as improving the life span and capacity of current types. Total cost of ownership For manufacturing, as TCO is typically compared with doing business overseas, it goes beyond the initial manufacturing cycle time and cost to make parts. TCO includes

1925-414: The end of the life cycle. A TCO analysis is used to gauge the viability of any capital investment . An enterprise may use it as a product/process comparison tool. It is also used by credit markets and financing agencies. TCO directly relates to an enterprise's asset and/or related systems total costs across all projects and processes, thus giving a picture of the profitability over time. TCO analysis

1980-427: The following as part of TCO: In the case of comparing TCO of existing versus proposed solutions, consideration should be put toward costs required to maintain the existing solution that may not necessarily be required for a proposed solution. Examples include cost of manual processing that are only required to support lack of existing automation, and extended support personnel. Total cost of ownership can be applied to

2035-457: The foundation of a standardized and holistic approach to implementing TCO key principles. Implementation of TCO key principles can improve decision making, maximizing financial strategies over the life of an asset, starting at the planning and design stage and extends to the end of the asset's life. APPA 1000-2, slated for publication in 2019, will focus on implementation and application of key TCO principals in facility management. The TCO concept

2090-455: The future. APPA, an ANSI Accredited Standards Developer, published APPA 1000-1 – Total Cost of Ownership for Facilities Asset Management (TCO) – Part 1: Key Principles as an American National Standard in December 2017.  APPA 1000-1 provides financial officers, facility professionals, architects, planners, construction workforce, and operations and maintenance (O&M) personnel

2145-459: The individual cells that make up the battery. For example, to charge a 12 V lead-acid battery (containing 6 cells of 2 V each) at 2.3 VPC requires a voltage of 13.8 V across the battery's terminals. Subjecting a discharged cell to a current in the direction which tends to discharge it further to the point the positive and negative terminals switch polarity causes a condition called cell reversal . Generally, pushing current through

2200-417: The industry. Ultracapacitors are being developed for transportation, using a large capacitor to store energy instead of the rechargeable battery banks used in hybrid vehicles . One drawback of capacitors compared to batteries is that the terminal voltage drops rapidly; a capacitor that has 25% of its initial energy left in it will have one-half of its initial voltage. By contrast, battery systems tend to have

2255-465: The link to point directly to the intended article. Retrieved from " https://en.wikipedia.org/w/index.php?title=VPC&oldid=1217695659 " Category : Disambiguation pages Hidden categories: Short description is different from Wikidata All article disambiguation pages All disambiguation pages Rechargeable battery#Charging and discharging A rechargeable battery , storage battery , or secondary cell (formally

VPC - Misplaced Pages Continue

2310-586: The low cost, makes it attractive for use in motor vehicles to provide the high current required by automobile starter motors . The nickel–cadmium battery (NiCd) was invented by Waldemar Jungner of Sweden in 1899. It uses nickel oxide hydroxide and metallic cadmium as electrodes . Cadmium is a toxic element, and was banned for most uses by the European Union in 2004. Nickel–cadmium batteries have been almost completely superseded by nickel–metal hydride (NiMH) batteries. The nickel–iron battery (NiFe)

2365-500: The number of charge cycles increases, until they are eventually considered to have reached the end of their useful life. Different battery systems have differing mechanisms for wearing out. For example, in lead-acid batteries, not all the active material is restored to the plates on each charge/discharge cycle; eventually enough material is lost that the battery capacity is reduced. In lithium-ion types, especially on deep discharge, some reactive lithium metal can be formed on charging, which

2420-510: The positive active material is oxidized , releasing electrons , and the negative material is reduced , absorbing electrons. These electrons constitute the current flow in the external circuit . The electrolyte may serve as a simple buffer for internal ion flow between the electrodes , as in lithium-ion and nickel-cadmium cells, or it may be an active participant in the electrochemical reaction, as in lead–acid cells. The energy used to charge rechargeable batteries usually comes from

2475-467: The positive electrode is the cathode on discharge and the anode on charge, and vice versa for the negative electrode. The lead–acid battery , invented in 1859 by French physicist Gaston Planté , is the oldest type of rechargeable battery. Despite having a very low energy-to-weight ratio and a low energy-to-volume ratio, its ability to supply high surge currents means that the cells have a relatively large power-to-weight ratio . These features, along with

2530-532: The positive exhibiting a reduction potential and the negative having an oxidation potential. The sum of the potentials from these half-reactions is the standard cell potential or voltage . In primary cells the positive and negative electrodes are known as the cathode and anode , respectively. Although this convention is sometimes carried through to rechargeable systems—especially with lithium-ion cells, because of their origins in primary lithium cells—this practice can lead to confusion. In rechargeable cells

2585-483: The range of 150–260   Wh/kg, batteries based on lithium-sulfur are expected to achieve 450–500   Wh/kg, and can eliminate cobalt, nickel and manganese from the production process. Furthermore, while initially lithium-sulfur batteries suffered from stability problems, recent research has made advances in developing lithium-sulfur batteries that cycle as long as (or longer than) batteries based on conventional lithium-ion technologies. The thin-film battery (TFB)

2640-461: The relationship between time and discharge rate is described by Peukert's law ; a lead-acid cell that can no longer sustain a usable terminal voltage at a high current may still have usable capacity, if discharged at a much lower rate. Data sheets for rechargeable cells often list the discharge capacity on 8-hour or 20-hour or other stated time; cells for uninterruptible power supply systems may be rated at 15-minute discharge. The terminal voltage of

2695-593: The risk is acceptable. Lithium-ion polymer batteries (LiPo) are light in weight, offer slightly higher energy density than Li-ion at slightly higher cost, and can be made in any shape. They are available but have not displaced Li-ion in the market. A primary use is for LiPo batteries is in powering remote-controlled cars, boats and airplanes. LiPo packs are readily available on the consumer market, in various configurations, up to 44.4 V, for powering certain R/C vehicles and helicopters or drones. Some test reports warn of

2750-595: The risk of fire when the batteries are not used in accordance with the instructions. Independent reviews of the technology discuss the risk of fire and explosion from lithium-ion batteries under certain conditions because they use liquid electrolytes. ‡ citations are needed for these parameters Several types of lithium–sulfur battery have been developed, and numerous research groups and organizations have demonstrated that batteries based on lithium sulfur can achieve superior energy density to other lithium technologies. Whereas lithium-ion batteries offer energy density in

2805-443: The structure and systems of a single building or a campus of buildings. Pioneered by Doug Christensen and the facilities department at Brigham Young University starting in the 1980s, the concept gained more traction in educational facilities in the early 21st century. The application of TCO in facilities goes beyond the predictive cost analysis for a new building’s “first cost” (planning, construction and commissioning), to factor in

SECTION 50

#1732780185731

2860-596: The technology to reduce cost, weight, and size, and increase lifetime. Older rechargeable batteries self-discharge relatively rapidly and require charging before first use; some newer low self-discharge NiMH batteries hold their charge for many months, and are typically sold factory-charged to about 70% of their rated capacity. Battery storage power stations use rechargeable batteries for load-leveling (storing electric energy at times of low demand for use during peak periods) and for renewable energy uses (such as storing power generated from photovoltaic arrays during

2915-582: The way it is to be measured. Due to variations during manufacture and aging, the DOD for complete discharge can change over time or number of charge cycles . Generally a rechargeable battery system will tolerate more charge/discharge cycles if the DOD is lower on each cycle. Lithium batteries can discharge to about 80 to 90% of their nominal capacity. Lead-acid batteries can discharge to about 50–60%. While flow batteries can discharge 100%. If batteries are used repeatedly even without mistreatment, they lose capacity as

2970-483: Was also developed by Waldemar Jungner in 1899; and commercialized by Thomas Edison in 1901 in the United States for electric vehicles and railway signalling . It is composed of only non-toxic elements, unlike many kinds of batteries that contain toxic mercury, cadmium, or lead. The nickel–metal hydride battery (NiMH) became available in 1989. These are now a common consumer and industrial type. The battery has

3025-579: Was popularized by the Gartner Group in 1987. The roots of this concept date at least back to the first quarter of the twentieth century. Many different methodologies and software tools have been developed to analyze TCO in various operational contexts. TCO is applied to the analysis of information technology products, seeking to quantify the financial impact of deploying a product over its life cycle . These technologies include software and hardware, and training. Technology deployment can include

#730269