Misplaced Pages

#406593

94-467: A standalone Carrier Routing System is deployed with a Line card chassis (LCC). The three main functional units of this LCC are the Line cards, Switching fabric and Route processor. The Line card consists of the physical interface card and a modular services card. The physical connectivity could be using fiber-optic cables or using Twisted pair cables. The routing decisions are made by the route processor and

188-414: A core surrounded by a cladding layer, both of which are made of dielectric materials. To confine the optical signal in the core, the refractive index of the core must be greater than that of the cladding. The boundary between the core and cladding may either be abrupt, in step-index fiber , or gradual, in graded-index fiber . Light can be fed into optical fibers using lasers or LEDs . Fiber

282-411: A wavelength shifter collect scintillation light in physics experiments . Fiber-optic sights for handguns, rifles, and shotguns use pieces of optical fiber to improve the visibility of markings on the sight. An optical fiber is a cylindrical dielectric waveguide ( nonconducting waveguide) that transmits light along its axis through the process of total internal reflection. The fiber consists of

376-475: A "loss budget" which is the maximum amount of loss that is allowed. Invisible infrared light (750 nm and larger) is used in commercial glass fiber communications because it has lower attenuation in such materials than visible light. However, the glass fibers will transmit visible light somewhat, which is convenient for simple testing of the fibers without requiring expensive equipment. Splices can be inspected visually, and adjusted for minimal light leakage at

470-426: A 16,000-kilometer distance, means that there is a minimum delay of 80 milliseconds (about 1 12 {\displaystyle {\tfrac {1}{12}}} of a second) between when one caller speaks and the other hears. When light traveling in an optically dense medium hits a boundary at a steep angle of incidence (larger than the critical angle for the boundary), the light is completely reflected. This

564-600: A camera mounted within a handheld device, which has an opening for the connectorized fiber and a USB output for connection to a display device such as a laptop. This makes the activity of looking for damage or dirt on the connector face much safer. Small glass fragments can also be a problem if they get under someone's skin, so care is needed to ensure that fragments produced when cleaving fiber are properly collected and disposed of appropriately. There are hybrid optical and electrical cables that are used in wireless outdoor Fiber To The Antenna (FTTA) applications. In these cables,

658-428: A central strength member normally made from fiberglass or plastic. There is also a copper conductor in external cables. Optical cables transfer data at the speed of light in glass. This is the speed of light in vacuum divided by the refractive index of the glass used, typically around 180,000 to 200,000 km/s, resulting in 5.0 to 5.5 microseconds of latency per km. Thus the round-trip delay time for 1000 km

752-423: A cladding made of pure silica, with an index of 1.444 at 1500 nm, and a core of doped silica with an index around 1.4475. The larger the index of refraction, the slower light travels in that medium. From this information, a simple rule of thumb is that a signal using optical fiber for communication will travel at around 200,000 kilometers per second. Thus a phone call carried by fiber between Sydney and New York,

846-790: A common outer jacket. The power conductors used in these hybrid cables are for directly powering an antenna or for powering tower-mounted electronics exclusively serving an antenna. They have a nominal voltage normally less than 60 VDC or 108/120 VAC. Other voltages may be present depending on the application and the relevant National Electrical Code (NEC). These types of hybrid cables may also be useful in other environments such as Distributed Antenna System (DAS) plants where they will serve antennas in indoor, outdoor, and roof-top locations. Considerations such as fire resistance, Nationally Recognized Testing Laboratory (NRTL) Listings, placement in vertical shafts, and other performance-related issues need to be fully addressed for these environments. Since

940-580: A composite unit consisting of up to four or six individual innerducts that are held together by some mechanical means, or a single extruded product having multiple channels through which to pull several cables. In either case, the multiduct is coilable, and can be pulled into existing conduit in a manner similar to that of conventional innerduct. Innerducts are primarily installed in underground conduit systems that provide connecting paths between manhole locations. In addition to placement in conduit, innerduct can be directly buried, or aerially installed by lashing

1034-451: A digital audio optical connection. This allows the streaming of audio over light, using the S/PDIF protocol over an optical TOSLINK connection. Fibers have many uses in remote sensing . In some applications, the fiber itself is the sensor (the fibers channel optical light to a processing device that analyzes changes in the light's characteristics). In other cases, fiber is used to connect

SECTION 10

#1732776129407

1128-522: A high-speed data connection between different parts of a building. Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide . This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers (or fibers formed into ribbons or bundles) then have

1222-522: A lasting impact on structures . It is based on the principle of measuring analog attenuation. In spectroscopy , optical fiber bundles transmit light from a spectrometer to a substance that cannot be placed inside the spectrometer itself, in order to analyze its composition. A spectrometer analyzes substances by bouncing light off and through them. By using fibers, a spectrometer can be used to study objects remotely. An optical fiber doped with certain rare-earth elements such as erbium can be used as

1316-478: A loose tube, the fiber may be embedded in a heavy polymer jacket, commonly called "tight buffer" construction. Tight buffer cables are offered for a variety of applications, but the two most common are " Breakout " and " Distribution ". Breakout cables normally contain a ripcord, two non-conductive dielectric strengthening members (normally a glass rod epoxy), an aramid yarn, and 3 mm buffer tubing with an additional layer of Kevlar surrounding each fiber. The ripcord

1410-423: A loss of 0.19 dB/km at 1550 nm. Plastic optical fiber (POF) loses much more: 1 dB/m at 650 nm. POF is large core (about 1 mm) fiber suitable only for short, low speed networks such as TOSLINK optical audio or for use within cars. Each connection between cables adds about 0.6 dB of average loss, and each joint (splice) adds about 0.1 dB. Many fiber optic cable connections have

1504-410: A means for subdividing conventional conduit that was originally designed for single, large-diameter metallic conductor cables into multiple channels for smaller optical cables. Innerducts are typically small-diameter, semi-flexible subducts. According to Telcordia GR-356 , there are three basic types of innerduct: smoothwall, corrugated, and ribbed. These various designs are based on the profile of

1598-437: A much more robust cable construction is required. In loose-tube construction the fiber is laid helically into semi-rigid tubes, allowing the cable to stretch without stretching the fiber itself. This protects the fiber from tension during laying and due to temperature changes. Loose-tube fiber may be "dry block" or gel-filled. Dry block offers less protection to the fibers than gel-filled, but costs considerably less. Instead of

1692-423: A network in an office building (see fiber to the office ), fiber-optic cabling can save space in cable ducts. This is because a single fiber can carry much more data than electrical cables such as standard category 5 cable , which typically runs at 100 Mbit/s or 1 Gbit/s speeds. Fibers are often also used for short-distance connections between devices. For example, most high-definition televisions offer

1786-537: A patchcord, if many patchcords are installed at one point. Individual fibers in a multi-fiber cable are often distinguished from one another by color-coded jackets or buffers on each fiber. The identification scheme used by Corning Cable Systems is based on EIA/TIA-598, "Optical Fiber Cable Color Coding" which defines identification schemes for fibers, buffered fibers, fiber units, and groups of fiber units within outside plant and premises optical fiber cables. This standard allows for fiber units to be identified by means of

1880-403: A plastic shell (such as SC connectors ) typically use a color-coded shell. Standard color codings for jackets (or buffers) and boots (or connector shells) are shown below: Remark: It is also possible that a small part of a connector is additionally color-coded, e.g. the lever of an E-2000 connector or a frame of an fiber-optic adapter . This additional color coding indicates the correct port for

1974-469: A printed legend. This method can be used for identification of fiber ribbons and fiber subunits. The legend will contain a corresponding printed numerical position number or color for use in identification. The color code used above resembles PE copper cables used in standard telephone wiring. In the UK a different color code is followed. Each 12-fiber bundle or element within a Cable Optical Fibre 200/201 cable

SECTION 20

#1732776129407

2068-474: A sensor to a measurement system. Optical fibers can be used as sensors to measure strain , temperature , pressure , and other quantities by modifying a fiber so that the property being measured modulates the intensity , phase , polarization , wavelength , or transit time of light in the fiber. Sensors that vary the intensity of light are the simplest since only a simple source and detector are required. A particularly useful feature of such fiber optic sensors

2162-555: A small fraction of the fibers in a cable may actually be in use. Companies can lease or sell the unused fiber to other providers who are looking for service in or through an area. Depending on specific local regulations, companies may overbuild their networks for the specific purpose of having a large network of dark fiber for sale, reducing the overall need for trenching and municipal permitting. Alternatively, they may deliberately under-invest to prevent their rivals from profiting from their investment. Optical fibers are very strong, but

2256-649: A target without a clear line-of-sight path. Many microscopes use fiber-optic light sources to provide intense illumination of samples being studied. Optical fiber is also used in imaging optics. A coherent bundle of fibers is used, sometimes along with lenses, for a long, thin imaging device called an endoscope , which is used to view objects through a small hole. Medical endoscopes are used for minimally invasive exploratory or surgical procedures. Industrial endoscopes (see fiberscope or borescope ) are used for inspecting anything hard to reach, such as jet engine interiors. In some buildings, optical fibers route sunlight from

2350-477: A tough resin buffer layer or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces crosstalk between the fibers, or reduces flare in fiber bundle imaging applications. For indoor applications,

2444-524: A transparent cladding. Later that same year, Harold Hopkins and Narinder Singh Kapany at Imperial College in London succeeded in making image-transmitting bundles with over 10,000 fibers, and subsequently achieved image transmission through a 75 cm long bundle which combined several thousand fibers. The first practical fiber optic semi-flexible gastroscope was patented by Basil Hirschowitz , C. Wilbur Peters, and Lawrence E. Curtiss, researchers at

2538-468: Is a mechanical splice , where the ends of the fibers are held in contact by mechanical force. Temporary or semi-permanent connections are made by means of specialized optical fiber connectors . The field of applied science and engineering concerned with the design and application of optical fibers is known as fiber optics . The term was coined by Indian-American physicist Narinder Singh Kapany . Daniel Colladon and Jacques Babinet first demonstrated

2632-401: Is a parallel cord of strong yarn that is situated under the jacket(s) of the cable for jacket removal. Distribution cables have an overall Kevlar wrapping, a ripcord, and a 900 micrometer buffer coating surrounding each fiber. These fiber units are commonly bundled with additional steel strength members, again with a helical twist to allow for stretching. A critical concern in outdoor cabling

2726-513: Is a potential laser safety hazard to technicians. The eye's natural defense against sudden exposure to bright light is the blink reflex , which is not triggered by infrared sources. In some cases the power levels are high enough to damage eyes, particularly when lenses or microscopes are used to inspect fibers that are emitting invisible infrared light. Inspection microscopes with optical safety filters are available to guard against this. More recently indirect viewing aids are used, which can comprise

2820-453: Is a way of measuring the speed of light in a material. Light travels fastest in a vacuum , such as in outer space. The speed of light in vacuum is about 300,000 kilometers (186,000 miles) per second. The refractive index of a medium is calculated by dividing the speed of light in vacuum by the speed of light in that medium. The refractive index of vacuum is therefore 1, by definition. A typical single-mode fiber used for telecommunications has

2914-548: Is an accepted version of this page A fiber-optic cable , also known as an optical-fiber cable , is an assembly similar to an electrical cable but containing one or more optical fibers that are used to carry light. The optical fiber elements are typically individually coated with plastic layers and contained in a protective tube suitable for the environment where the cable is used. Different types of cable are used for fiber-optic communication in different applications, for example long-distance telecommunication or providing

Carrier Routing System - Misplaced Pages Continue

3008-501: Is around 11 milliseconds. Signal loss in optic fiber is measured in decibels (dB). A loss of 3 dB across a link means the light at the far end is only half the intensity of the light that was sent into the fiber. A 6 dB loss means only one quarter of the light made it through the fiber. Once too much light has been lost, the signal is too weak to recover and the link becomes unreliable and eventually ceases to function entirely. The exact point at which this happens depends on

3102-506: Is backward compatible with the previous generation HW. At the time of launch, CRS-X family has three different flavors of physical interface card (40x10GE, 4x100GE and 2x100GE-Flex-40) apart from the improved fabric and modular service cards. Cisco states that the CRS-X can be used in back-to-back & multi-chassis deployments and that CRS-1, CRS-3 & CRS-X can co-exist in a multi-chassis setup. The press release (reference) also claims that,

3196-411: Is bent towards the perpendicular ... When the ray passes from water to air it is bent from the perpendicular... If the angle which the ray in water encloses with the perpendicular to the surface be greater than 48 degrees, the ray will not quit the water at all: it will be totally reflected at the surface... The angle which marks the limit where total reflection begins is called the limiting angle of

3290-412: Is called multi-mode fiber , from the electromagnetic analysis (see below). In a step-index multi-mode fiber, rays of light are guided along the fiber core by total internal reflection. Rays that meet the core-cladding boundary at an angle (measured relative to a line normal to the boundary) greater than the critical angle for this boundary, are completely reflected. The critical angle is determined by

3384-418: Is called total internal reflection . This effect is used in optical fibers to confine light in the core. Most modern optical fiber is weakly guiding , meaning that the difference in refractive index between the core and the cladding is very small (typically less than 1%). Light travels through the fiber core, bouncing back and forth off the boundary between the core and cladding. Because the light must strike

3478-453: Is colored as follows: Each element is in a tube within the cable (not a blown fiber tube) The cable elements start with the red tube and are counted around the cable to the green tube. Active elements are in white tubes and yellow fillers or dummies are laid in the cable to fill it out depending on how many fibers and units exists – can be up to 276 fibers or 23 elements for external cable and 144 fibers or 12 elements for internal. The cable has

3572-507: Is designed for use in the near infrared . Multi-mode fiber, by comparison, is manufactured with core diameters as small as 50 micrometers and as large as hundreds of micrometers. Some special-purpose optical fiber is constructed with a non-cylindrical core or cladding layer, usually with an elliptical or rectangular cross-section. These include polarization-maintaining fiber used in fiber optic sensors and fiber designed to suppress whispering gallery mode propagation. Photonic-crystal fiber

3666-565: Is far less than in electrical copper cables, leading to long-haul fiber connections with repeater distances of 70–150 kilometers (43–93 mi). Two teams, led by David N. Payne of the University of Southampton and Emmanuel Desurvire at Bell Labs , developed the erbium-doped fiber amplifier , which reduced the cost of long-distance fiber systems by reducing or eliminating optical-electrical-optical repeaters, in 1986 and 1987 respectively. The emerging field of photonic crystals led to

3760-564: Is immune to electrical interference as there is no cross-talk between signals in different cables and no pickup of environmental noise. Information traveling inside the optical fiber is even immune to electromagnetic pulses generated by nuclear devices. Fiber cables do not conduct electricity, which makes fiber useful for protecting communications equipment in high voltage environments such as power generation facilities or applications prone to lightning strikes. The electrical isolation also prevents problems with ground loops . Because there

3854-418: Is important in fiber optic communication. This is more complex than joining electrical wire or cable and involves careful cleaving of the fibers, precise alignment of the fiber cores, and the coupling of these aligned cores. For applications that demand a permanent connection a fusion splice is common. In this technique, an electric arc is used to melt the ends of the fibers together. Another common technique

Carrier Routing System - Misplaced Pages Continue

3948-611: Is kept in the core by the phenomenon of total internal reflection which causes the fiber to act as a waveguide . Fibers that support many propagation paths or transverse modes are called multi-mode fibers , while those that support a single mode are called single-mode fibers (SMF). Multi-mode fibers generally have a wider core diameter and are used for short-distance communication links and for applications where high power must be transmitted. Single-mode fibers are used for most communication links longer than 1,050 meters (3,440 ft). Being able to join optical fibers with low loss

4042-405: Is made with a regular pattern of index variation (often in the form of cylindrical holes that run along the length of the fiber). Such fiber uses diffraction effects instead of or in addition to total internal reflection, to confine light to the fiber's core. The properties of the fiber can be tailored to a wide variety of applications. Attenuation in fiber optics, also known as transmission loss,

4136-412: Is monitored and analyzed for disturbances. This return signal is digitally processed to detect disturbances and trip an alarm if an intrusion has occurred. Optical fibers are widely used as components of optical chemical sensors and optical biosensors . Optical fiber can be used to transmit power using a photovoltaic cell to convert the light into electricity. While this method of power transmission

4230-403: Is no Fabric Card Chassis involved as in the case of a multi-chassis configuration. This configuration works only for the 8-slot and 16-slot chassis models. CRS-3 also supports IPoDWDM . This solution reduces transport elements, while supporting multilayer features such as proactive protection and control plane interaction, reducing operating expenses and capital costs. AT&T Corporation tested

4324-439: Is no electricity in optical cables that could potentially generate sparks, they can be used in environments where explosive fumes are present. Wiretapping (in this case, fiber tapping ) is more difficult compared to electrical connections. Fiber cables are not targeted for metal theft . In contrast, copper cable systems use large amounts of copper and have been targeted since the 2000s commodities boom . The refractive index

4418-478: Is not as efficient as conventional ones, it is especially useful in situations where it is desirable not to have a metallic conductor as in the case of use near MRI machines, which produce strong magnetic fields. Other examples are for powering electronics in high-powered antenna elements and measurement devices used in high-voltage transmission equipment. Optical fibers are used as light guides in medical and other applications where bright light needs to be shone on

4512-418: Is that they can, if required, provide distributed sensing over distances of up to one meter. Distributed acoustic sensing is one example of this. In contrast, highly localized measurements can be provided by integrating miniaturized sensing elements with the tip of the fiber. These can be implemented by various micro- and nanofabrication technologies, such that they do not exceed the microscopic boundary of

4606-422: Is the numerical aperture (NA) of the fiber. Fiber with a larger NA requires less precision to splice and work with than fiber with a smaller NA. The size of this acceptance cone is a function of the refractive index difference between the fiber's core and cladding. Single-mode fiber has a small NA. Fiber with large core diameter (greater than 10 micrometers) may be analyzed by geometrical optics . Such fiber

4700-474: Is the measurement of temperature inside jet engines by using a fiber to transmit radiation into a pyrometer outside the engine. Extrinsic sensors can be used in the same way to measure the internal temperature of electrical transformers , where the extreme electromagnetic fields present make other measurement techniques impossible. Extrinsic sensors measure vibration, rotation, displacement, velocity, acceleration, torque, and torsion. A solid-state version of

4794-428: Is the reduction in the intensity of the light signal as it travels through the transmission medium. Attenuation coefficients in fiber optics are usually expressed in units of dB/km. The medium is usually a fiber of silica glass that confines the incident light beam within. Attenuation is an important factor limiting the transmission of a digital signal across large distances. Thus, much research has gone into both limiting

SECTION 50

#1732776129407

4888-672: Is the second generation of the CRS series launched in March, 2010. In CRS-3 each line card slot has a capacity of 140 Gbits/s, which is more than three times the capacity of the previous CRS-1 generation. The architecture is retained as in the previous generation and hardware is compatible with the CRS-1 system. Apart from the single-chassis system and the multi-chassis system, CRS-3 supports back-to-back configuration as well. In this configuration, two Line Card Chassis are connected back-to-back and there

4982-476: Is to protect the fiber from damage by water. This is accomplished by use of solid barriers such as copper tubes, and water-repellent jelly or water-absorbing powder surrounding the fiber. Finally, the cable may be armored to protect it from environmental hazards, such as construction work or gnawing animals. Undersea cables are more heavily armored in their near-shore portions to protect them from boat anchors, fishing gear, and even sharks , which may be attracted to

5076-484: Is typical in deployed systems. Through the use of wavelength-division multiplexing (WDM), each fiber can carry many independent channels, each using a different wavelength of light. The net data rate (data rate without overhead bytes) per fiber is the per-channel data rate reduced by the forward error correction (FEC) overhead, multiplied by the number of channels (usually up to 80 in commercial dense WDM systems as of 2008 ). For short-distance applications, such as

5170-402: Is used as a medium for telecommunication and computer networking because it is flexible and can be bundled as cables. It is especially advantageous for long-distance communications, because infrared light propagates through the fiber with much lower attenuation compared to electricity in electrical cables. This allows long distances to be spanned with few repeaters . 10 or 40 Gbit/s

5264-411: Is used for very short-range and consumer applications, whereas glass fiber is used for short/medium-range ( multi-mode ) and long-range ( single-mode ) telecommunications. The buffer or jacket on patchcords is often color-coded to indicate the type of fiber used. The strain relief "boot" that protects the fiber from bending at a connector is color-coded to indicate the type of connection. Connectors with

5358-471: The University of Michigan , in 1956. In the process of developing the gastroscope, Curtiss produced the first glass-clad fibers; previous optical fibers had relied on air or impractical oils and waxes as the low-index cladding material. Kapany coined the term fiber optics after writing a 1960 article in Scientific American that introduced the topic to a wide audience. He subsequently wrote

5452-405: The gain medium of a fiber laser or optical amplifier . Rare-earth-doped optical fibers can be used to provide signal amplification by splicing a short section of doped fiber into a regular (undoped) optical fiber line. The doped fiber is optically pumped with a second laser wavelength that is coupled into the line in addition to the signal wave. Both wavelengths of light are transmitted through

5546-680: The CRS switch fabrics are based on a three-stage Benes architecture . In a single-chassis system, the three switching stages—S1, S2, and S3—are all contained on one fabric card. In a multi-chassis system, the S2 stage is contained within the Fabric Card Chassis, with the S1 and S3 stages resident in the Line Card Chassis. The CRS Line card chassis comes in three different flavors: 4-slot, 8-slot and 16-slot. The number of slots indicates

5640-625: The CRS-3 in a live-network using the 100 Gb Ethernet backbone and the Dutch telco KPN Telecom selected the CRS-3 platform for their new NextGen IP backbone . CRS-1 is the first generation of Carrier Routing System launched in 2004. This replaced the Cisco 12000 routers which were used as core routers. Each slot of CRS-1 has a capacity of 40 Gbit/s. CRS-1 supports both standalone and multi-chassis configurations. Fiber-optic cable This

5734-507: The CRS-X 400 GE Line Card with Cisco AnyPort Technology uses Cisco’s CMOS photonic CPAK to reduce power consumption, heat dissipation and increase 100 GE port densities by a factor of three compared to competitive solutions. The Universal Port concept adds the option of using a 100G port as 2 ports of 40G or 10 ports of 10G. 40G can again be used as 4 ports 10G. This product will go up against Juniper Networks ’ T4000 and PTX core routing systems and perhaps Alcatel-Lucent ’s 7950 XRS. The CRS-3

SECTION 60

#1732776129407

5828-564: The attenuation in fibers available at the time was caused by impurities that could be removed, rather than by fundamental physical effects such as scattering. They correctly and systematically theorized the light-loss properties for optical fiber and pointed out the right material to use for such fibers— silica glass with high purity. This discovery earned Kao the Nobel Prize in Physics in 2009. The crucial attenuation limit of 20 dB/km

5922-416: The boundary with an angle greater than the critical angle, only light that enters the fiber within a certain range of angles can travel down the fiber without leaking out. This range of angles is called the acceptance cone of the fiber. There is a maximum angle from the fiber axis at which light may enter the fiber so that it will propagate, or travel, in the core of the fiber. The sine of this maximum angle

6016-457: The cameras had to be supervised by someone with an appropriate security clearance. Charles K. Kao and George A. Hockham of the British company Standard Telephones and Cables (STC) were the first to promote the idea that the attenuation in optical fibers could be reduced below 20 decibels per kilometer (dB/km), making fibers a practical communication medium, in 1965. They proposed that

6110-416: The case of a fiberscope . Specially designed fibers are also used for a variety of other applications, such as fiber optic sensors and fiber lasers . Glass optical fibers are typically made by drawing , while plastic fibers can be made either by drawing or by extrusion . Optical fibers typically include a core surrounded by a transparent cladding material with a lower index of refraction . Light

6204-407: The core-cladding boundary. The resulting curved paths reduce multi-path dispersion because high-angle rays pass more through the lower-index periphery of the core, rather than the high-index center. The index profile is chosen to minimize the difference in axial propagation speeds of the various rays in the fiber. This ideal index profile is very close to a parabolic relationship between the index and

6298-442: The development in 1991 of photonic-crystal fiber , which guides light by diffraction from a periodic structure, rather than by total internal reflection. The first photonic crystal fibers became commercially available in 2000. Photonic crystal fibers can carry higher power than conventional fibers and their wavelength-dependent properties can be manipulated to improve performance. These fibers can have hollow cores. Optical fiber

6392-467: The difference in the index of refraction between the core and cladding materials. Rays that meet the boundary at a low angle are refracted from the core into the cladding where they terminate. The critical angle determines the acceptance angle of the fiber, often reported as a numerical aperture . A high numerical aperture allows light to propagate down the fiber in rays both close to the axis and at various angles, allowing efficient coupling of light into

6486-445: The distance from the axis. Fiber with a core diameter less than about ten times the wavelength of the propagating light cannot be modeled using geometric optics. Instead, it must be analyzed as an electromagnetic waveguide structure, according to Maxwell's equations as reduced to the electromagnetic wave equation . As an optical waveguide, the fiber supports one or more confined transverse modes by which light can propagate along

6580-621: The doped fiber, which transfers energy from the second pump wavelength to the signal wave. The process that causes the amplification is stimulated emission . Optical fiber is also widely exploited as a nonlinear medium. The glass medium supports a host of nonlinear optical interactions, and the long interaction lengths possible in fiber facilitate a variety of phenomena, which are harnessed for applications and fundamental investigation. Conversely, fiber nonlinearity can have deleterious effects on optical signals, and measures are often required to minimize such unwanted effects. Optical fibers doped with

6674-421: The electrical power that is carried to power amplifiers or repeaters in the cable. Modern cables come in a wide variety of sheathings and armor, designed for applications such as direct burial in trenches, dual use as power lines, installation in conduit, lashing to aerial telephone poles, submarine installation , and insertion in paved streets. In September 2012, NTT Japan demonstrated a single fiber cable that

6768-424: The fiber tip, allowing for such applications as insertion into blood vessels via hypodermic needle. Extrinsic fiber optic sensors use an optical fiber cable , normally a multi-mode one, to transmit modulated light from either a non-fiber optical sensor—or an electronic sensor connected to an optical transmitter. A major benefit of extrinsic sensors is their ability to reach otherwise inaccessible places. An example

6862-404: The fiber. Fiber supporting only one mode is called single-mode . The waveguide analysis shows that the light energy in the fiber is not completely confined in the core. Instead, especially in single-mode fibers, a significant fraction of the energy in the bound mode travels in the cladding as an evanescent wave . The most common type of single-mode fiber has a core diameter of 8–10 micrometers and

6956-438: The fiber. However, this high numerical aperture increases the amount of dispersion as rays at different angles have different path lengths and therefore take different amounts of time to traverse the fiber. In graded-index fiber, the index of refraction in the core decreases continuously between the axis and the cladding. This causes light rays to bend smoothly as they approach the cladding, rather than reflecting abruptly from

7050-493: The first book about the new field. The first working fiber-optic data transmission system was demonstrated by German physicist Manfred Börner at Telefunken Research Labs in Ulm in 1965, followed by the first patent application for this technology in 1966. In 1968, NASA used fiber optics in the television cameras that were sent to the moon. At the time, the use in the cameras was classified confidential , and employees handling

7144-510: The guiding of light by refraction, the principle that makes fiber optics possible, in Paris in the early 1840s. John Tyndall included a demonstration of it in his public lectures in London , 12 years later. Tyndall also wrote about the property of total internal reflection in an introductory book about the nature of light in 1870: When the light passes from air into water, the refracted ray

7238-469: The gyroscope, using the interference of light, has been developed. The fiber optic gyroscope (FOG) has no moving parts and exploits the Sagnac effect to detect mechanical rotation. Common uses for fiber optic sensors include advanced intrusion detection security systems . The light is transmitted along a fiber optic sensor cable placed on a fence, pipeline, or communication cabling, and the returned signal

7332-668: The indoor plant, similar criteria are in Telcordia GR-409, Generic Requirements for Indoor Fiber Optic Cable . The jacket material is application-specific. The material determines the mechanical robustness, chemical and UV radiation resistance, and so on. Some common jacket materials are LSZH , polyvinyl chloride , polyethylene , polyurethane , polybutylene terephthalate , and polyamide . There are two main types of material used for optical fibers: glass and plastic. They offer widely different characteristics and find uses in very different applications. Generally, plastic fiber

7426-852: The innerduct to a steel suspension strand. As stated in GR-356, cable is typically placed into innerduct in one of three ways. It may be Optical fiber An optical fiber , or optical fibre , is a flexible glass or plastic fiber that can transmit light from one end to the other. Such fibers find wide usage in fiber-optic communications , where they permit transmission over longer distances and at higher bandwidths (data transfer rates) than electrical cables. Fibers are used instead of metal wires because signals travel along them with less loss and are immune to electromagnetic interference . Fibers are also used for illumination and imaging, and are often wrapped in bundles so they may be used to carry light into, or images out of confined spaces, as in

7520-419: The inside and outside diameters of the innerduct. The need for a specific characteristic or combination of characteristics, such as pulling strength, flexibility, or the lowest coefficient of friction, dictates the type of innerduct required. Beyond the basic profiles or contours (smoothwall, corrugated, or ribbed), innerduct is also available in an increasing variety of multiduct designs. Multiduct may be either

7614-435: The jacketed fiber is generally enclosed, together with a bundle of flexible fibrous polymer strength members like aramid (e.g. Twaron or Kevlar ), in a lightweight plastic cover to form a simple cable. Each end of the cable may be terminated with a specialized optical fiber connector to allow it to be easily connected and disconnected from transmitting and receiving equipment. For use in more strenuous environments,

7708-421: The joint, which maximizes light transmission between the ends of the fibers being joined. The charts Understanding wavelengths in fiber optics and Optical power loss (attenuation) in fiber illustrate the relationship of visible light to the infrared frequencies used, and show the absorption water bands between 850, 1300 and 1550 nm. The infrared light used in telecommunications cannot be seen, so there

7802-413: The medium. For water this angle is 48°27′, for flint glass it is 38°41′, while for a diamond it is 23°42′. In the late 19th century, a team of Viennese doctors guided light through bent glass rods to illuminate body cavities. Practical applications such as close internal illumination during dentistry followed, early in the twentieth century. Image transmission through tubes was demonstrated independently by

7896-489: The number of line cards that the chassis can accommodate. There is only one variety of Fabric card chassis. Cisco Systems has announced the addition of a new product to its existing CRS family, the Carrier Routing System X, or CRS-X (C-R-S-Ten), which is expected to be 10 times faster than the first CRS model (CRS-1) the company offered, back in 2004. CRS-X is said to be a 400 Gbit/s per slot system and

7990-611: The optical fibers carry information, and the electrical conductors are used to transmit power. These cables can be placed in several environments to serve antennas mounted on poles, towers, and other structures. According to Telcordia GR-3173 , Generic Requirements for Hybrid Optical and Electrical Cables for Use in Wireless Outdoor Fiber To The Antenna (FTTA) Applications, these hybrid cables have optical fibers, twisted pair/quad elements, coaxial cables or current-carrying electrical conductors under

8084-416: The radio experimenter Clarence Hansell and the television pioneer John Logie Baird in the 1920s. In the 1930s, Heinrich Lamm showed that one could transmit images through a bundle of unclad optical fibers and used it for internal medical examinations, but his work was largely forgotten. In 1953, Dutch scientist Bram van Heel first demonstrated image transmission through bundles of optical fibers with

8178-431: The roof to other parts of the building (see nonimaging optics ). Optical-fiber lamps are used for illumination in decorative applications, including signs , art , toys and artificial Christmas trees . Optical fiber is an intrinsic part of the light-transmitting concrete building product LiTraCon . Optical fiber can also be used in structural health monitoring . This type of sensor can detect stresses that may have

8272-568: The speed of manufacture to over 50 meters per second, making optical fiber cables cheaper than traditional copper ones. These innovations ushered in the era of optical fiber telecommunication. The Italian research center CSELT worked with Corning to develop practical optical fiber cables, resulting in the first metropolitan fiber optic cable being deployed in Turin in 1977. CSELT also developed an early technique for splicing optical fibers, called Springroove. Attenuation in modern optical cables

8366-755: The strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging. Telcordia GR-20, Generic Requirements for Optical Fiber and Optical Fiber Cable , contains reliability and quality criteria to protect optical fiber in all operating conditions. The criteria concentrate on conditions in an outside plant (OSP) environment. For

8460-550: The switching fabric takes care of the routing based on the Route processor input. The CRS runs IOS XR which is said to be designed for high-end carrier grade routers and was launched with CRS-1. In a multi-chassis deployment, the Line card chassis is used along with another variety of chassis called as the Fabric Card Chassis (FCC). The architecture enables scalability by increasing the number of Line Card Chassis and/or Fabric Card Chassis. In both single- and multi-chassis configurations,

8554-410: The transmitter power and the sensitivity of the receiver. Typical modern multimode graded-index fibers have 3 dB per kilometre of attenuation (signal loss) at a wavelength of 850 nm , and 1 dB/km at 1300 nm. Singlemode loses 0.35 dB/km at 1310 nm and 0.25 dB/km at 1550 nm. Very high quality singlemode fiber intended for long distance applications is specified at

8648-413: The voltage levels and power levels used within these hybrid cables vary, electrical safety codes consider the hybrid cable to be a power cable, which needs to comply with rules on clearance, separation, etc. Innerducts are installed in existing underground conduit systems to provide clean, continuous, low-friction paths for placing optical cables that have relatively low pulling tension limits. They provide

8742-475: Was able to transfer 1 petabit per second ( 10 bits/s ) over a distance of 50 kilometers. Although larger cables are available, the highest strand-count single-mode fiber cable commonly manufactured is the 864-count, consisting of 36 ribbons each containing 24 strands of fiber. These high fiber count cables are used in data centers , and as distribution cables in HFC and PON networks. In some cases, only

8836-675: Was first achieved in 1970 by researchers Robert D. Maurer , Donald Keck , Peter C. Schultz , and Frank Zimar working for American glass maker Corning Glass Works . They demonstrated a fiber with 17 dB/km attenuation by doping silica glass with titanium . A few years later they produced a fiber with only 4 dB/km attenuation using germanium dioxide as the core dopant. In 1981, General Electric produced fused quartz ingots that could be drawn into strands 25 miles (40 km) long. Initially, high-quality optical fibers could only be manufactured at 2 meters per second. Chemical engineer Thomas Mensah joined Corning in 1983 and increased

#406593