Misplaced Pages

#474525

64-632: The Brookport Bridge (officially the Paducah-Brookport Bridge 1929–43, and the Irvin S. Cobb Bridge since 1943) is a ten-span, steel deck (grate), narrow two-lane truss bridge that carries U.S. Route 45 (US 45) across the Ohio River in the U.S. states of Illinois and Kentucky . It connects Paducah, Kentucky , north to Brookport, Illinois . On February 4, 1927, Kentucky congressman Alben William Barkley introduced

128-470: A Parker truss or Pratt truss than a true arch . In the Brown truss all vertical elements are under tension, with exception of the end posts. This type of truss is particularly suited for timber structures that use iron rods as tension members. See Lenticular truss below. This combines an arch with a truss to form a structure both strong and rigid. Most trusses have the lower chord under tension and

192-677: A covered bridge to protect the structure. In 1820, a simple form of truss, Town's lattice truss , was patented, and had the advantage of requiring neither high labor skills nor much metal. Few iron truss bridges were built in the United States before 1850. Truss bridges became a common type of bridge built from the 1870s through the 1930s. Examples of these bridges still remain across the US, but their numbers are dropping rapidly as they are demolished and replaced with new structures. As metal slowly started to replace timber, wrought iron bridges in

256-526: A 90-day experiment further lowered the passenger car fee to 25 cents each way, anticipating that increases in vehicle traffic would make up for the reduced fees, and the reduction was made permanent in June. By 1939, an average of 1000 vehicles daily were using the bridge. In February 1941, the toll for automobiles was again reduced, to 15 cents. In November 1943, the structure was renamed the Irvin S. Cobb Bridge as

320-550: A Parker truss vary from near vertical in the center of the span to diagonal near each end, similar to a Warren truss. George H. Pegram , while the chief engineer of Edge Moor Iron Company in Wilmington, Delaware , patented this truss design in 1885. The Pegram truss consists of a Parker type design with the vertical posts leaning towards the center at an angle between 60 and 75°. The variable post angle and constant chord length allowed steel in existing bridges to be recycled into

384-552: A bill authorizing the Paducah Board of Trade to construct the bridge. Following House and Senate passage, President Calvin Coolidge signed the bill on February 23. Paducah's Board of Trade consulted with several bond houses about financing, and the bid from Toledo's Stranahan, Harris & Otis was accepted on March 17, with construction cost then estimated as one to two million dollars. Traffic surveys—preliminaries to siting

448-594: A continuous truss functions as a single rigid structure over multiple supports. This means that the live load on one span is partially supported by the other spans, and consequently it is possible to use less material in the truss. Continuous truss bridges were not very common before the mid-20th century because they are statically indeterminate , which makes them difficult to design without the use of computers . A multi-span truss bridge may also be constructed using cantilever spans, which are supported at only one end rather than both ends like other types of trusses. Unlike

512-523: A continuous truss, a cantilever truss does not need to be connected rigidly, or indeed at all, at the center. Many cantilever bridges, like the Quebec Bridge shown below, have two cantilever spans supporting a simple truss in the center. The bridge would remain standing if the simple truss section were removed. Bridges are the most widely known examples of truss use. There are many types, some of them dating back hundreds of years. Below are some of

576-435: A conventional truss into place or by building it in place using a "traveling support". In another method of construction, one outboard half of each balanced truss is built upon temporary falsework. When the outboard halves are completed and anchored the inboard halves may then be constructed and the center section completed as described above. The Fink truss was designed by Albert Fink of Germany in 1854. This type of bridge

640-605: A lack of durability, and gave way to the Pratt truss design, which was stronger. Again, the bridge companies marketed their designs, with the Wrought Iron Bridge Company in the lead. As the 1880s and 1890s progressed, steel began to replace wrought iron as the preferred material. Other truss designs were used during this time, including the camel-back. By the 1910s, many states developed standard plan truss bridges, including steel Warren pony truss bridges. In

704-477: A lower chord (functioning as a suspension cable) that curves down and then up to meet at the same end points. Where the arches extend above and below the roadbed, it is called a lenticular pony truss bridge . The Pauli truss bridge is a specific variant of the lenticular truss, but the terms are not interchangeable. One type of lenticular truss consists of arcuate upper compression chords and lower eyebar chain tension links. Brunel 's Royal Albert Bridge over

SECTION 10

#1732801311475

768-452: A new four-lane bridge which can carry traffic the way modern traffic must be carried....The best bet for a new bridge over the Ohio [River] here is for Interstate-24 to come close to here and cross the river near Metropolis. This is our only hope for a new bridge until time really runs its course the way it did with covered bridges. The nearby four-lane Interstate 24 Bridge , three miles west of

832-726: A new span using the Pegram truss design. This design also facilitated reassembly and permitted a bridge to be adjusted to fit different span lengths. There are twelve known remaining Pegram span bridges in the United States with seven in Idaho , two in Kansas , and one each in California , Washington , and Utah . The Pennsylvania (Petit) truss is a variation on the Pratt truss . The Pratt truss includes braced diagonal members in all panels;

896-445: A strike; before the collapse, similar incidents had been common and had necessitated frequent repairs. Truss bridges consisting of more than one span may be either a continuous truss or a series of simple trusses. In the simple truss design, each span is supported only at the ends and is fully independent of any adjacent spans. Each span must fully support the weight of any vehicles traveling over it (the live load ). In contrast,

960-402: A tribute to the state's famed journalist-humorist Irvin S. Cobb , a Paducah native. That same month, tolls were eliminated. By the 1960s, a Paducah newspaper columnist was among those hoping for a modern replacement: The Brookport bridge was built for the 1920s. It was magnificent then; it is old and outmoded and almost a bottleneck now....We’ve got an outmoded bridge that, in the near future,

1024-545: A variant of the lenticular truss, "with the top chord carefully shaped so that it has a constant force along the entire length of the truss." It is named after Friedrich Augustus von Pauli  [ de ] , whose 1857 railway bridge (the Großhesseloher Brücke  [ de ] ) spanned the Isar near Munich . ( See also Grosshesselohe Isartal station .) The term Pauli truss is not interchangeable with

1088-700: Is a Pratt truss design with a polygonal upper chord. A "camelback" is a subset of the Parker type, where the upper chord consists of exactly five segments. An example of a Parker truss is the Traffic Bridge in Saskatoon , Canada. An example of a camelback truss is the Woolsey Bridge near Woolsey, Arkansas . Designed and patented in 1872 by Reuben Partridge , after local bridge designs proved ineffective against road traffic and heavy rains. It became

1152-613: Is a continuous box and plate girder bridge over the Tennessee River opened on December 18, 1967. It is just slightly upstream from Nickajack Dam and was within sight of the former Marion Memorial Bridge . This article about a bridge in Illinois is a stub . You can help Misplaced Pages by expanding it . This article about a bridge in Kentucky is a stub . You can help Misplaced Pages by expanding it . This article about

1216-519: Is a hybrid between a Warren truss and a double-intersection Pratt truss. Invented in 1863 by Simeon S. Post, it is occasionally referred to as a Post patent truss although he never received a patent for it. The Ponakin Bridge and the Bell Ford Bridge are two examples of this truss. A Pratt truss includes vertical members and diagonals that slope down towards the center, the opposite of

1280-547: Is a two-span tied arch bridge that carries I-24 across the Ohio River . Built in 1973, it is 5,623.4 feet (1,714.0 m) in length and has two main spans, 731.5 feet (223.0 m) and 633 feet (193 m) long. It is one of two road bridges connecting the Metropolis - Brookport, Illinois area with Paducah, Kentucky , with the other being the Brookport Bridge upstream to the east. The Interstate 24 Bridge

1344-399: Is going to be a bigger problem even than it is now....It’s just that you drive along the bridge and there is nothing but a rail between you and a mighty river; the bridge is scary. It will be as long as it is just an ordinary road hanging up there with nothing but rails on the side. You’ve got to widen it so that there’ll be some play between that road and the rails. But what really is needed is

SECTION 20

#1732801311475

1408-832: Is named after the K formed in each panel by the vertical member and two oblique members. Examples include the Südbrücke rail bridge over the River Rhine, Mainz, Germany, the bridge on I-895 (Baltimore Harbor Tunnel Thruway) in Baltimore, Maryland, the Long–Allen Bridge in Morgan City, Louisiana (Morgan City Bridge) with three 600-foot-long spans, and the Wax Lake Outlet bridge in Calumet, Louisiana One of

1472-695: Is practical for use with spans up to 250 feet (76 m) and was a common configuration for railroad bridges as truss bridges moved from wood to metal. They are statically determinate bridges, which lend themselves well to long spans. They were common in the United States between 1844 and the early 20th century. Examples of Pratt truss bridges are the Governor's Bridge in Maryland ; the Hayden RR Bridge in Springfield, Oregon , built in 1882;

1536-525: Is the Victoria Bridge on Prince Street, Picton, New South Wales . Also constructed of ironbark, the bridge is still in use today for pedestrian and light traffic. The Bailey truss was designed by the British in 1940–1941 for military uses during World War II. A short selection of prefabricated modular components could be easily and speedily combined on land in various configurations to adapt to

1600-611: Is used in the teaching of statics, by the building of model bridges from spaghetti . Spaghetti is brittle and although it can carry a modest tension force, it breaks easily if bent. A model spaghetti bridge thus demonstrates the use of a truss structure to produce a usefully strong complete structure from individually weak elements. In the United States , because wood was in abundance, early truss bridges would typically use carefully fitted timbers for members taking compression and iron rods for tension members , usually constructed as

1664-621: The Dearborn River High Bridge near Augusta, Montana, built in 1897; and the Fair Oaks Bridge in Fair Oaks, California , built 1907–09. The Scenic Bridge near Tarkio, Montana , is an example of a Pratt deck truss bridge, where the roadway is on top of the truss. The queenpost truss , sometimes called "queen post" or queenspost, is similar to a king post truss in that the outer supports are angled towards

1728-1258: The Fort Wayne Street Bridge in Goshen, Indiana , the Schell Bridge in Northfield, Massachusetts , the Inclined Plane Bridge in Johnstown, Pennsylvania , the Easton–Phillipsburg Toll Bridge in Easton, Pennsylvania , the Connecticut River Bridge in Brattleboro, Vermont , the Metropolis Bridge in Metropolis, Illinois , and the Healdsburg Memorial Bridge in Healdsburg, California . A Post truss

1792-495: The Howe truss . The interior diagonals are under tension under balanced loading and vertical elements under compression. If pure tension elements (such as eyebars ) are used in the diagonals, then crossing elements may be needed near the center to accept concentrated live loads as they traverse the span. It can be subdivided, creating Y- and K-shaped patterns. The Pratt truss was invented in 1844 by Thomas and Caleb Pratt. This truss

1856-481: The River Tamar between Devon and Cornwall uses a single tubular upper chord. As the horizontal tension and compression forces are balanced these horizontal forces are not transferred to the supporting pylons (as is the case with most arch types). This in turn enables the truss to be fabricated on the ground and then to be raised by jacking as supporting masonry pylons are constructed. This truss has been used in

1920-399: The analysis of its structure using a few assumptions and the application of Newton's laws of motion according to the branch of physics known as statics . For purposes of analysis, trusses are assumed to be pin jointed where the straight components meet, meaning that taken alone, every joint on the structure is functionally considered to be a flexible joint as opposed to a rigid joint with

1984-412: The 1920s and 1930s, Pennsylvania and several states continued to build steel truss bridges, using massive steel through-truss bridges for long spans. Other states, such as Michigan , used standard plan concrete girder and beam bridges, and only a limited number of truss bridges were built. The truss may carry its roadbed on top, in the middle, or at the bottom of the truss. Bridges with the roadbed at

Brookport Bridge - Misplaced Pages Continue

2048-454: The Cobb bridge, was completed in 1973. The Cobb bridge—still the “Brookport bridge” to many locals—is presently challenging to cross, due to its very narrow lanes and steel grate deck. It is restricted to vehicles less than 8 feet (2.4 m) in width and 9 feet 6 inches (2.90 m) in height, preventing most commercial vehicles from using the bridge. Truss bridge The nature of a truss allows

2112-756: The Milwaukee builder the Wisconsin Bridge and Iron Co., were sued for $ 40,000. The lawsuit was heard in Louisville on June 9 in the U.S. District Court in Louisville. In 1932, the Paducah-Brookport Bridge Company indicated its willingness to explore a sale to the State of Kentucky. Until September 1933, that firm operated the bridge; whereupon the bridge's bondholders—in a procedure commonly used to protect such mortgages—sold

2176-685: The Pennsylvania truss adds to this design half-length struts or ties in the top, bottom, or both parts of the panels. It is named after the Pennsylvania Railroad , which pioneered this design. It was once used for hundreds of bridges in the United States, but fell out of favor in the 1930s and very few examples of this design remain. Examples of this truss type include the Lower Trenton Bridge in Trenton, New Jersey ,

2240-545: The US started being built on a large scale in the 1870s. Bowstring truss bridges were a common truss design during this time, with their arched top chords. Companies like the Massillon Bridge Company of Massillon, Ohio , and the King Bridge Company of Cleveland , became well-known, as they marketed their designs to cities and townships. The bowstring truss design fell out of favor due to

2304-454: The balance between labor, machinery, and material costs has certain favorable proportions. The inclusion of the elements shown is largely an engineering decision based upon economics, being a balance between the costs of raw materials, off-site fabrication, component transportation, on-site erection, the availability of machinery, and the cost of labor. In other cases, the appearance of the structure may take on greater importance and so influence

2368-560: The bridge for $ 800,000, subject to approval by the Federal court supervising its receivership status. On July 10, the state formally awarded $ 800,000 in bridge bonds, paying 3-1/2% annually for 20 years, to the Kentucky-Illinois Bridge Company, the bonds to be underwritten primarily through tolls; the bond transfer would be completed by August 15. The State of Kentucky gradually reduced tolls. In February 1938,

2432-425: The bridge illustrated in the infobox at the top, vertical members are in tension, lower horizontal members in tension, shear , and bending, outer diagonal and top members are in compression, while the inner diagonals are in tension. The central vertical member stabilizes the upper compression member, preventing it from buckling . If the top member is sufficiently stiff then this vertical element may be eliminated. If

2496-594: The bridge in foreclosure to a Delaware-registered corporation supervised by the bondholders, the Kentucky-Illinois Bridge Corporation, for $ 300,000. During its first six years of operation, the bridge's average annual gross income from tolls were only about $ 69,000, and net losses for 1931-1932-1933 alone totaled $ 457,509.40. On February 15, 1935, the Kentucky State Highway Commission voted 6–2 to purchase

2560-529: The bridge's opening, boosted tourism to Paducah and Brookport. By mid-August, all fares were reduced, and round-trip discounts offered: $ 1 for any automobile and its passengers, $ 1.25 for the two-way fare. On October 23, 1929, a river steamer, the Chaperon —which was towing a showboat—struck a submerged concrete block below the bridge which had been created to facilitate construction but was unmarked by light or buoy. The Paducah-Brookport Bridge Company, along with

2624-540: The bridge—began on March 24. The bridge was designed by the Kansas City firm of Harrington, Howard and Ashe, and construction was superintended by Chicago's P.W. Chapman & Company. The Paducah-Ohio River Bridge Company would be the bridge's legal owner-operator. The final obstacle to groundbreaking was surmounted upon obtaining the War Department's approval for the project on July 22. Construction began in

Brookport Bridge - Misplaced Pages Continue

2688-570: The center of the structure. The primary difference is the horizontal extension at the center which relies on beam action to provide mechanical stability. This truss style is only suitable for relatively short spans. The Smith truss , patented by Robert W Smith on July 16, 1867, has mostly diagonal criss-crossed supports. Smith's company used many variations of this pattern in the wooden covered bridges it built. Interstate 24 Bridge The Interstate 24 Bridge may refer to one of two distinct bridges on Interstate 24 . The Interstate 24 Bridge

2752-732: The center, the opposite of the Pratt truss . In contrast to the Pratt truss, the diagonal web members are in compression and the vertical web members are in tension. Few of these bridges remain standing. Examples include Jay Bridge in Jay, New York ; McConnell's Mill Covered Bridge in Slippery Rock Township, Lawrence County, Pennsylvania ; Sandy Creek Covered Bridge in Jefferson County, Missouri ; and Westham Island Bridge in Delta, British Columbia , Canada. The K-truss

2816-414: The compression members and to control deflection. It is mainly used for rail bridges, showing off a simple and very strong design. In the Pratt truss the intersection of the verticals and the lower horizontal tension members are used to anchor the supports for the short-span girders under the tracks (among other things). With the Baltimore truss, there are almost twice as many points for this to happen because

2880-600: The construction of a stadium, with the upper chords of parallel trusses supporting a roof that may be rolled back. The Smithfield Street Bridge in Pittsburgh, Pennsylvania , is another example of this type. An example of a lenticular pony truss bridge that uses regular spans of iron is the Turn-of-River Bridge designed and manufactured by the Berlin Iron Bridge Co. The Pauli truss is

2944-429: The design decisions beyond mere matters of economics. Modern materials such as prestressed concrete and fabrication methods, such as automated welding , and the changing price of steel relative to that of labor have significantly influenced the design of modern bridges. A pure truss can be represented as a pin-jointed structure, one where the only forces on the truss members are tension or compression, not bending. This

3008-484: The earliest examples is the Old Blenheim Bridge , which with a span of 210 feet (64 m) and a total length of 232 feet (71 m) long was the second-longest covered bridge in the United States, until its destruction from flooding in 2011. The Busching bridge, often erroneously used as an example of a Long truss, is an example of a Howe truss, as the verticals are metal rods. A Parker truss bridge

3072-652: The fall of 1927 and continued year-round, sometimes slowed by high water on the Ohio River. As early as October 1928, the State of Kentucky proposed taking over the bridge and—once tolls had paid off its bonds—making passage toll-free. The Paducah-Brookport Bridge officially opened on Sunday, April 14, 1929, with a toll schedule of ten cents for pedestrians, bicyclists, and passengers on buses; fifty cents for horse-drawn vehicles; $ 1 for an automobile and its driver, with five cents added for each passenger; and higher tolls for trucks and other large vehicles. The bridge's final cost

3136-482: The lower chord (a horizontal member of a truss) is sufficiently resistant to bending and shear, the outer vertical elements may be eliminated, but with additional strength added to other members in compensation. The ability to distribute the forces in various ways has led to a large variety of truss bridge types. Some types may be more advantageous when the wood is employed for compression elements while other types may be easier to erect in particular site conditions, or when

3200-515: The more common designs. The Allan truss , designed by Percy Allan , is partly based on the Howe truss . The first Allan truss was completed on 13 August 1894 over Glennies Creek at Camberwell, New South Wales and the last Allan truss bridge was built over Mill Creek near Wisemans Ferry in 1929. Completed in March 1895, the Tharwa Bridge located at Tharwa, Australian Capital Territory ,

3264-412: The needs at the site and allow rapid deployment of completed trusses. In the image, note the use of pairs of doubled trusses to adapt to the span and load requirements. In other applications the trusses may be stacked vertically, and doubled as necessary. The Baltimore truss is a subclass of the Pratt truss. A Baltimore truss has additional bracing in the lower section of the truss to prevent buckling in

SECTION 50

#1732801311475

3328-474: The roadbed but are not connected, a pony truss or half-through truss. Sometimes both the upper and lower chords support roadbeds, forming a double-decked truss . This can be used to separate rail from road traffic or to separate the two directions of road traffic. Since through truss bridges have supports located over the bridge deck, they are susceptible to being hit by overheight loads when used on highways. The I-5 Skagit River bridge collapsed after such

3392-574: The short verticals will also be used to anchor the supports. Thus the short-span girders can be made lighter because their span is shorter. A good example of the Baltimore truss is the Amtrak Old Saybrook – Old Lyme Bridge in Connecticut , United States. The Bollman Truss Railroad Bridge at Savage, Maryland , United States is the only surviving example of a revolutionary design in the history of American bridge engineering. The type

3456-451: The simplest truss styles to implement, the king post consists of two angled supports leaning into a common vertical support. This type of bridge uses a substantial number of lightweight elements, easing the task of construction. Truss elements are usually of wood, iron, or steel. A lenticular truss bridge includes a lens-shape truss, with trusses between an upper chord functioning as an arch that curves up and then down to end points, and

3520-454: The standard for covered bridges built in central Ohio in the late 1800s and early 1900s. The Pegram truss is a hybrid between the Warren and Parker trusses where the upper chords are all of equal length and the lower chords are longer than the corresponding upper chord. Because of the difference in upper and lower chord length, each panel is not square. The members which would be vertical in

3584-414: The strength to maintain its shape, and the resulting shape and strength of the structure are only maintained by the interlocking of the components. This assumption means that members of the truss (chords, verticals, and diagonals) will act only in tension or compression. A more complex analysis is required where rigid joints impose significant bending loads upon the elements, as in a Vierendeel truss . In

3648-481: The term lenticular truss and, according to Thomas Boothby, the casual use of the term has clouded the literature. The Long truss was designed by Stephen H. Long in 1830. The design resembles a Howe truss , but is entirely made of wood instead of a combination of wood and metal. The longest surviving example is the Eldean Covered Bridge north of Troy, Ohio , spanning 224 feet (68 m). One of

3712-542: The top or the bottom are the most common as this allows both the top and bottom to be stiffened, forming a box truss . When the roadbed is atop the truss, it is a deck truss; an example of this was the I-35W Mississippi River bridge . When the truss members are both above and below the roadbed it is called a through truss; an example of this is the Pulaski Skyway , and where the sides extend above

3776-428: The upper chord under compression. In a cantilever truss the situation is reversed, at least over a portion of the span. The typical cantilever truss bridge is a "balanced cantilever", which enables the construction to proceed outward from a central vertical spar in each direction. Usually these are built in pairs until the outer sections may be anchored to footings. A central gap, if present, can then be filled by lifting

3840-414: Was also easy to assemble. Wells Creek Bollman Bridge is the only other bridge designed by Wendel Bollman still in existence, but it is a Warren truss configuration. The bowstring truss bridge was patented in 1841 by Squire Whipple . While similar in appearance to a tied-arch bridge , a bowstring truss has diagonal load-bearing members: these diagonals result in a structure that more closely matches

3904-423: Was approximately $ 2 million, and it was used by approximately 1200 automobiles on its first day in operation. The bridge's formal dedication was on May 9, 1929, with thousands in attendance. The ceremonial ribbon-cutting by "Miss Paducah" Hazel Miller, and appearances of Paducah's and Brookport's mayors, were included in Paramount's newsreel celebrating these festivities. Sunday toll discounts, implemented soon after

SECTION 60

#1732801311475

3968-405: Was named after its inventor, Wendel Bollman , a self-educated Baltimore engineer. It was the first successful all-metal bridge design (patented in 1852) to be adopted and consistently used on a railroad. The design employs wrought iron tension members and cast iron compression members. The use of multiple independent tension elements reduces the likelihood of catastrophic failure. The structure

4032-445: Was popular with the Baltimore and Ohio Railroad . The Appomattox High Bridge on the Norfolk and Western Railway included 21 Fink deck truss spans from 1869 until their replacement in 1886. There are also inverted Fink truss bridges such as the Moody Pedestrian Bridge in Austin, Texas. The Howe truss , patented in 1840 by Massachusetts millwright William Howe , includes vertical members and diagonals that slope up towards

4096-536: Was the second Allan truss bridge to be built, the oldest surviving bridge in the Australian Capital Territory and the oldest, longest continuously used Allan truss bridge. Completed in November 1895, the Hampden Bridge in Wagga Wagga, New South Wales , Australia, the first of the Allan truss bridges with overhead bracing, was originally designed as a steel bridge but was constructed with timber to reduce cost. In his design, Allan used Australian ironbark for its strength. A similar bridge also designed by Percy Allen

#474525