Misplaced Pages

#218781

109-475: A helicopter is a type of rotorcraft in which lift and thrust are supplied by horizontally spinning rotors . This allows the helicopter to take off and land vertically , to hover , and to fly forward, backward and laterally. These attributes allow helicopters to be used in congested or isolated areas where fixed-wing aircraft and many forms of short take-off and landing ( STOL ) or short take-off and vertical landing ( STOVL ) aircraft cannot perform without

218-415: A "canard" foreplane as well as a conventional tailplane, offloading the rotor wing and providing control during forward flight. For vertical and low-speed flight, the main airfoil is tip-driven as a helicopter's rotor by exhaust from a jet engine , and there is no need for a tail rotor . In high-speed flight the airfoil is stopped in a spanwise position, as the main wing of a three-surface aircraft , and

327-476: A limit value of one, for large time t . In other words, velocity asymptotically approaches a maximum value called the terminal velocity v t : v t = 2 m g ρ A C D . {\displaystyle v_{t}={\sqrt {\frac {2mg}{\rho AC_{D}}}}.\,} For an object falling and released at relative-velocity v  = v i at time t  = 0, with v i < v t ,

436-665: A limit value of one, for large time t . Velocity asymptotically tends to the terminal velocity v t , strictly from above v t . For v i = v t , the velocity is constant: v ( t ) = v t . {\displaystyle v(t)=v_{t}.} These functions are defined by the solution of the following differential equation : g − ρ A C D 2 m v 2 = d v d t . {\displaystyle g-{\frac {\rho AC_{D}}{2m}}v^{2}={\frac {dv}{dt}}.\,} Or, more generically (where F ( v ) are

545-614: A runway . In 1942, the Sikorsky R-4 became the first helicopter to reach full-scale production . Although most earlier designs used more than one main rotor, the configuration of a single main rotor accompanied by a vertical anti-torque tail rotor (i.e. unicopter , not to be confused with the single-blade monocopter ) has become the most common helicopter configuration. However, twin-rotor helicopters (bicopters), in either tandem or transverse rotors configurations, are sometimes in use due to their greater payload capacity than

654-425: A tail rotor , fantail , or NOTAR , except some rare examples of helicopters using tip jet propulsion, which generates almost no torque. An autogyro (sometimes called gyrocopter, gyroplane, or rotaplane) uses an unpowered rotor, driven by aerodynamic forces in a state of autorotation to develop lift, and an engine-powered propeller , similar to that of a fixed-wing aircraft , to provide thrust. While similar to

763-470: A tailsitter configuration in which the lifting surfaces act as a rotors during takeoff, the craft tilts over for horizontal flight and the rotor stops to act as a fixed wing. Aerodynamic drag In fluid dynamics , drag , sometimes referred to as fluid resistance , is a force acting opposite to the relative motion of any object moving with respect to a surrounding fluid . This can exist between two fluid layers, two solid surfaces, or between

872-443: A collective input is made, all the blades change equally, and the result is the helicopter increasing or decreasing in altitude. A swashplate controls the collective and cyclic pitch of the main blades. The swashplate moves up and down, along the main shaft, to change the pitch of both blades. This causes the helicopter to push air downward or upward, depending on the angle of attack . The swashplate can also change its angle to move

981-416: A constant altitude. The pedals serve the same function in both a helicopter and a fixed-wing aircraft, to maintain balanced flight. This is done by applying a pedal input in whichever direction is necessary to center the ball in the turn and bank indicator . Due to the operating characteristics of the helicopter—its ability to take off and land vertically, and to hover for extended periods of time, as well as

1090-609: A few more flights and achieved a height of nearly 2.0 metres (6.5 ft), but it proved to be unstable and was abandoned. Rotorcraft Rotorcraft generally include aircraft where one or more rotors provide lift throughout the entire flight, such as helicopters , autogyros , and gyrodynes . Compound rotorcraft augment the rotor with additional thrust engines, propellers, or static lifting surfaces. Some types, such as helicopters, are capable of vertical takeoff and landing . An aircraft which uses rotor lift for vertical flight but changes to solely fixed-wing lift in horizontal flight

1199-526: A fluid and a solid surface. Drag forces tend to decrease fluid velocity relative to the solid object in the fluid's path. Unlike other resistive forces, drag force depends on velocity. This is because drag force is proportional to the velocity for low-speed flow and the velocity squared for high-speed flow. This distinction between low and high-speed flow is measured by the Reynolds number . Examples of drag include: Types of drag are generally divided into

SECTION 10

#1732794047219

1308-809: A fluid at relatively slow speeds (assuming there is no turbulence). Purely laminar flow only exists up to Re = 0.1 under this definition. In this case, the force of drag is approximately proportional to velocity. The equation for viscous resistance is: F D = − b v {\displaystyle \mathbf {F} _{D}=-b\mathbf {v} \,} where: When an object falls from rest, its velocity will be v ( t ) = ( ρ − ρ 0 ) V g b ( 1 − e − b t / m ) {\displaystyle v(t)={\frac {(\rho -\rho _{0})\,V\,g}{b}}\left(1-e^{-b\,t/m}\right)} where: The velocity asymptotically approaches

1417-450: A fluid increases as the cube of the velocity increases. For example, a car cruising on a highway at 50 mph (80 km/h) may require only 10 horsepower (7.5 kW) to overcome aerodynamic drag, but that same car at 100 mph (160 km/h) requires 80 hp (60 kW). With a doubling of speeds, the drag/force quadruples per the formula. Exerting 4 times the force over a fixed distance produces 4 times as much work . At twice

1526-462: A gift by their father, would inspire the Wright brothers to pursue the dream of flight. In 1861, the word "helicopter" was coined by Gustave de Ponton d'Amécourt , a French inventor who demonstrated a small steam-powered model. While celebrated as an innovative use of a new metal, aluminum, the model never lifted off the ground. D'Amecourt's linguistic contribution would survive to eventually describe

1635-405: A helicopter determines the size, function and capability of that helicopter design. The earliest helicopter engines were simple mechanical devices, such as rubber bands or spindles, which relegated the size of helicopters to toys and small models. For a half century before the first airplane flight, steam engines were used to forward the development of the understanding of helicopter aerodynamics, but

1744-508: A helicopter powered by a gasoline engine with box kites attached to a mast by cables for a rotor, but it never flew. In 1906, two French brothers, Jacques and Louis Breguet , began experimenting with airfoils for helicopters. In 1907, those experiments resulted in the Gyroplane No.1 , possibly as the earliest known example of a quadcopter. Although there is some uncertainty about the date, sometime between 14 August and 29 September 1907,

1853-423: A helicopter rotor in appearance, the autogyro's rotor must have air flowing up and through the rotor disk in order to generate rotation. Early autogyros resembled the fixed-wing aircraft of the day, with wings and a front-mounted engine and propeller in a tractor configuration to pull the aircraft through the air. Late-model autogyros feature a rear-mounted engine and propeller in a pusher configuration. The autogyro

1962-415: A helicopter. This is because a helicopter generates its own gusty air while in a hover, which acts against the fuselage and flight control surfaces. The result is constant control inputs and corrections by the pilot to keep the helicopter where it is required to be. Despite the complexity of the task, the control inputs in a hover are simple. The cyclic is used to eliminate drift in the horizontal plane, that

2071-693: A human body ( d {\displaystyle d} ≈0.6 m) v t {\displaystyle v_{t}} ≈70 m/s, for a small animal like a cat ( d {\displaystyle d} ≈0.2 m) v t {\displaystyle v_{t}} ≈40 m/s, for a small bird ( d {\displaystyle d} ≈0.05 m) v t {\displaystyle v_{t}} ≈20 m/s, for an insect ( d {\displaystyle d} ≈0.01 m) v t {\displaystyle v_{t}} ≈9 m/s, and so on. Terminal velocity for very small objects (pollen, etc.) at low Reynolds numbers

2180-674: A minimum at some airspeed - an aircraft flying at this speed will be at or close to its optimal efficiency. Pilots will use this speed to maximize endurance (minimum fuel consumption), or maximize gliding range in the event of an engine failure. Drag depends on the properties of the fluid and on the size, shape, and speed of the object. One way to express this is by means of the drag equation : F D = 1 2 ρ v 2 C D A {\displaystyle F_{\mathrm {D} }\,=\,{\tfrac {1}{2}}\,\rho \,v^{2}\,C_{\mathrm {D} }\,A} where The drag coefficient depends on

2289-475: A process of rebracketing , the word is often (erroneously, from an etymological point of view) perceived by English speakers as consisting of heli- and -copter , leading to words like helipad and quadcopter . English language nicknames for "helicopter" include "chopper", "copter", "heli", and "whirlybird". In the United States military, the common slang is "helo" pronounced /ˈhiː.loʊ/. A helicopter

SECTION 20

#1732794047219

2398-491: A rotor. The spinning creates lift, and the toy flies when released. The 4th-century AD Daoist book Baopuzi by Ge Hong ( 抱朴子 "Master who Embraces Simplicity") reportedly describes some of the ideas inherent to rotary wing aircraft. Designs similar to the Chinese helicopter toy appeared in some Renaissance paintings and other works. In the 18th and early 19th centuries Western scientists developed flying machines based on

2507-440: A single main rotor, but torque created by its aerodynamic drag must be countered by an opposed torque. The design that Igor Sikorsky settled on for his VS-300 was a smaller tail rotor. The tail rotor pushes or pulls against the tail to counter the torque effect, and this has become the most common configuration for helicopter design, usually at the end of a tail boom . Some helicopters use other anti-torque controls instead of

2616-468: A small sphere with radius r {\displaystyle r} = 0.5 micrometre (diameter = 1.0 μm) moving through water at a velocity v {\displaystyle v} of 10 μm/s. Using 10 Pa·s as the dynamic viscosity of water in SI units, we find a drag force of 0.09 pN. This is about the drag force that a bacterium experiences as it swims through water. The drag coefficient of

2725-623: A sphere can be determined for the general case of a laminar flow with Reynolds numbers less than 2 ⋅ 10 5 {\displaystyle 2\cdot 10^{5}} using the following formula: C D = 24 R e + 4 R e + 0.4   ;           R e < 2 ⋅ 10 5 {\displaystyle C_{D}={\frac {24}{Re}}+{\frac {4}{\sqrt {Re}}}+0.4~{\text{;}}~~~~~Re<2\cdot 10^{5}} For Reynolds numbers less than 1, Stokes' law applies and

2834-416: A state called translational lift which provides extra lift without increasing power. This state, most typically, occurs when the airspeed reaches approximately 16–24 knots (30–44 km/h; 18–28 mph), and may be necessary for a helicopter to obtain flight. In forward flight a helicopter's flight controls behave more like those of a fixed-wing aircraft. Applying forward pressure on the cyclic will cause

2943-428: Is a cylindrical metal shaft that extends upwards from the transmission. At the top of the mast is the attachment point for the rotor blades called the hub. Main rotor systems are classified according to how the rotor blades are attached and move relative to the hub. There are three basic types: hingeless, fully articulated, and teetering; although some modern rotor systems use a combination of these. Most helicopters have

3052-451: Is a type of rotorcraft in which lift and thrust are supplied by one or more horizontally-spinning rotors. By contrast the autogyro (or gyroplane) and gyrodyne have a free-spinning rotor for all or part of the flight envelope, relying on a separate thrust system to propel the craft forwards, so that the airflow sets the rotor spinning to provide lift. The compound helicopter also has a separate thrust system, but continues to supply power to

3161-558: Is about v t = g d ρ o b j ρ . {\displaystyle v_{t}={\sqrt {gd{\frac {\rho _{obj}}{\rho }}}}.\,} For objects of water-like density (raindrops, hail, live objects—mammals, birds, insects, etc.) falling in air near Earth's surface at sea level, the terminal velocity is roughly equal to with d in metre and v t in m/s. v t = 90 d , {\displaystyle v_{t}=90{\sqrt {d}},\,} For example, for

3270-448: Is also defined in terms of the hyperbolic tangent function: v ( t ) = v t tanh ⁡ ( t g v t + arctanh ⁡ ( v i v t ) ) . {\displaystyle v(t)=v_{t}\tanh \left(t{\frac {g}{v_{t}}}+\operatorname {arctanh} \left({\frac {v_{i}}{v_{t}}}\right)\right).\,} For v i > v t ,

3379-625: Is asymptotically proportional to R e − 1 {\displaystyle \mathrm {Re} ^{-1}} , which means that the drag is linearly proportional to the speed, i.e. the drag force on a small sphere moving through a viscous fluid is given by the Stokes Law : F d = 3 π μ D v {\displaystyle F_{\rm {d}}=3\pi \mu Dv} At high R e {\displaystyle \mathrm {Re} } , C D {\displaystyle C_{\rm {D}}}

Helicopter - Misplaced Pages Continue

3488-452: Is called an aerial crane . Aerial cranes are used to place heavy equipment, like radio transmission towers and large air conditioning units, on the tops of tall buildings, or when an item must be raised up in a remote area, such as a radio tower raised on the top of a hill or mountain. Helicopters are used as aerial cranes in the logging industry to lift trees out of terrain where vehicles cannot travel and where environmental concerns prohibit

3597-399: Is determined by Stokes law. In short, terminal velocity is higher for larger creatures, and thus potentially more deadly. A creature such as a mouse falling at its terminal velocity is much more likely to survive impact with the ground than a human falling at its terminal velocity. The equation for viscous resistance or linear drag is appropriate for objects or particles moving through

3706-547: Is equipped to stabilize and provide limited medical treatment to a patient while in flight. The use of helicopters as air ambulances is often referred to as " MEDEVAC ", and patients are referred to as being "airlifted", or "medevaced". This use was pioneered in the Korean War , when time to reach a medical facility was reduced to three hours from the eight hours needed in World War II , and further reduced to two hours by

3815-458: Is increased to the propeller, less power is required by the rotor to provide forward thrust resulting in reduced pitch angles and rotor blade flapping. At cruise speeds with most or all of the thrust being provided by the propellers, the rotor receives power only sufficient to overcome the profile drag and maintain lift. The effect is a rotorcraft operating in a more efficient manner than the freewheeling rotor of an autogyro in autorotation, minimizing

3924-408: Is known as bluff or blunt when the source of drag is dominated by pressure forces, and streamlined if the drag is dominated by viscous forces. For example, road vehicles are bluff bodies. For aircraft, pressure and friction drag are included in the definition of parasitic drag . Parasite drag is often expressed in terms of a hypothetical. This is the area of a flat plate perpendicular to the flow. It

4033-406: Is made up of multiple components including viscous pressure drag ( form drag ), and drag due to surface roughness ( skin friction drag ). Additionally, the presence of multiple bodies in relative proximity may incur so called interference drag , which is sometimes described as a component of parasitic drag. In aviation, induced drag tends to be greater at lower speeds because a high angle of attack

4142-428: Is more or less constant, but drag will vary as the square of the speed varies. The graph to the right shows how C D {\displaystyle C_{\rm {D}}} varies with R e {\displaystyle \mathrm {Re} } for the case of a sphere. Since the power needed to overcome the drag force is the product of the force times speed, the power needed to overcome drag will vary as

4251-415: Is not a rotorcraft but a convertiplane . A helicopter is a powered rotorcraft with rotors driven by the engine(s) throughout the flight, allowing it to take off and land vertically, hover, and fly forward, backward, or laterally. Helicopters have several different configurations of one or more main rotors. Helicopters with a single shaft-driven main lift rotor require some sort of antitorque device such as

4360-472: Is presented at Drag equation § Derivation . The reference area A is often the orthographic projection of the object, or the frontal area, on a plane perpendicular to the direction of motion. For objects with a simple shape, such as a sphere, this is the cross sectional area. Sometimes a body is a composite of different parts, each with a different reference area (drag coefficient corresponding to each of those different areas must be determined). In

4469-473: Is required to maintain lift, creating more drag. However, as speed increases the angle of attack can be reduced and the induced drag decreases. Parasitic drag, however, increases because the fluid is flowing more quickly around protruding objects increasing friction or drag. At even higher speeds ( transonic ), wave drag enters the picture. Each of these forms of drag changes in proportion to the others based on speed. The combined overall drag curve therefore shows

Helicopter - Misplaced Pages Continue

4578-674: Is the Sud-Ouest Djinn , and an example of the hot tip jet helicopter is the YH-32 Hornet . Some radio-controlled helicopters and smaller, helicopter-type unmanned aerial vehicles , use electric motors or motorcycle engines. Radio-controlled helicopters may also have piston engines that use fuels other than gasoline, such as nitromethane . Some turbine engines commonly used in helicopters can also use biodiesel instead of jet fuel. There are also human-powered helicopters . A helicopter has four flight control inputs. These are

4687-583: Is the Reynolds number related to fluid path length L. As mentioned, the drag equation with a constant drag coefficient gives the force moving through fluid a relatively large velocity, i.e. high Reynolds number , Re > ~1000. This is also called quadratic drag . F D = 1 2 ρ v 2 C D A , {\displaystyle F_{D}\,=\,{\tfrac {1}{2}}\,\rho \,v^{2}\,C_{D}\,A,} The derivation of this equation

4796-755: Is the wind speed and v o {\displaystyle v_{o}} is the object speed (both relative to ground). Velocity as a function of time for an object falling through a non-dense medium, and released at zero relative-velocity v  = 0 at time t  = 0, is roughly given by a function involving a hyperbolic tangent (tanh): v ( t ) = 2 m g ρ A C D tanh ⁡ ( t g ρ C D A 2 m ) . {\displaystyle v(t)={\sqrt {\frac {2mg}{\rho AC_{D}}}}\tanh \left(t{\sqrt {\frac {g\rho C_{D}A}{2m}}}\right).\,} The hyperbolic tangent has

4905-410: Is to control forward and back, right and left. The collective is used to maintain altitude. The pedals are used to control nose direction or heading . It is the interaction of these controls that makes hovering so difficult, since an adjustment in any one control requires an adjustment of the other two, creating a cycle of constant correction. As a helicopter moves from hover to forward flight it enters

5014-547: Is used when comparing the drag of different aircraft For example, the Douglas DC-3 has an equivalent parasite area of 2.20 m (23.7 sq ft) and the McDonnell Douglas DC-9 , with 30 years of advancement in aircraft design, an area of 1.91 m (20.6 sq ft) although it carried five times as many passengers. Lift-induced drag (also called induced drag ) is drag which occurs as

5123-571: The Bell 205 and the Erickson S-64 Aircrane helitanker. Helicopters are used as air ambulances for emergency medical assistance in situations when an ambulance cannot easily or quickly reach the scene, or cannot transport the patient to a medical facility in time. Helicopters are also used when patients need to be transported between medical facilities and air transportation is the most practical method. An air ambulance helicopter

5232-583: The Bell 206 with 3,400. Most were in North America with 34.3% then in Europe with 28.0% followed by Asia-Pacific with 18.6%, Latin America with 11.6%, Africa with 5.3% and Middle East with 1.7%. The earliest references for vertical flight came from China. Since around 400 BC, Chinese children have played with bamboo flying toys (or Chinese top). This bamboo-copter is spun by rolling a stick attached to

5341-526: The Cornu helicopter which used two 6.1-metre (20 ft) counter-rotating rotors driven by a 24 hp (18 kW) Antoinette engine. On 13 November 1907, it lifted its inventor to 0.3 metres (1 ft) and remained aloft for 20 seconds. Even though this flight did not surpass the flight of the Gyroplane No. 1, it was reported to be the first truly free flight with a pilot. Cornu's helicopter completed

5450-671: The Lockheed F-104 Starfighter with a triangular rotor wing. The idea was later revisited by Hughes. The Sikorsky S-72 research aircraft underwent extensive flight testing. In 1986 the Sikorsky S-72 Rotor Systems Research Aircraft (RSRA) was fitted with a four-bladed stopped rotor, known as the X-wing. The programme was cancelled two years later, before the rotor had flown. The later canard rotor/wing (CRW) concept added

5559-497: The Vietnam War . In naval service a prime function of rescue helicopters is to promptly retrieve downed aircrew involved in crashes occurring upon launch or recovery aboard aircraft carriers. In past years this function was performed by destroyers escorting the carrier, but since then helicopters have proved vastly more effective. Police departments and other law enforcement agencies use helicopters to pursue suspects and patrol

SECTION 50

#1732794047219

5668-410: The lift coefficient also increases, and so too does the lift-induced drag. At the onset of stall , lift is abruptly decreased, as is lift-induced drag, but viscous pressure drag, a component of parasite drag, increases due to the formation of turbulent unattached flow in the wake behind the body. Parasitic drag , or profile drag, is drag caused by moving a solid object through a fluid. Parasitic drag

5777-413: The order 10 ). For an object with well-defined fixed separation points, like a circular disk with its plane normal to the flow direction, the drag coefficient is constant for Re  > 3,500. The further the drag coefficient C d is, in general, a function of the orientation of the flow with respect to the object (apart from symmetrical objects like a sphere). Under the assumption that

5886-558: The Bambi bucket, are usually filled by submerging the bucket into lakes, rivers, reservoirs, or portable tanks. Tanks fitted onto helicopters are filled from a hose while the helicopter is on the ground or water is siphoned from lakes or reservoirs through a hanging snorkel as the helicopter hovers over the water source. Helitack helicopters are also used to deliver firefighters, who rappel down to inaccessible areas, and to resupply firefighters. Common firefighting helicopters include variants of

5995-760: The Chinese top in a model consisting of contrarotating turkey flight feathers as rotor blades, and in 1784, demonstrated it to the French Academy of Sciences . Sir George Cayley , influenced by a childhood fascination with the Chinese flying top, developed a model of feathers, similar to that of Launoy and Bienvenu, but powered by rubber bands. By the end of the century, he had progressed to using sheets of tin for rotor blades and springs for power. His writings on his experiments and models would become influential on future aviation pioneers. Alphonse Pénaud would later develop coaxial rotor model helicopter toys in 1870, also powered by rubber bands. One of these toys, given as

6104-475: The Chinese toy. It was not until the early 1480s, when Italian polymath Leonardo da Vinci created a design for a machine that could be described as an " aerial screw ", that any recorded advancement was made towards vertical flight. His notes suggested that he built small flying models, but there were no indications for any provision to stop the rotor from making the craft rotate. As scientific knowledge increased and became more accepted, people continued to pursue

6213-451: The Gyroplane No. 1 lifted its pilot into the air about 0.6 metres (2 ft) for a minute. The Gyroplane No.   1 proved to be extremely unsteady and required a man at each corner of the airframe to hold it steady. For this reason, the flights of the Gyroplane No.   1 are considered to be the first manned flight of a helicopter, but not a free or untethered flight. That same year, fellow French inventor Paul Cornu designed and built

6322-569: The Martian atmosphere is 100 times thinner than Earth's, its two blades spin at close to 3,000 revolutions a minute, approximately 10 times faster than that of a terrestrial helicopter. In 2017, 926 civil helicopters were shipped for $ 3.68 billion, led by Airbus Helicopters with $ 1.87 billion for 369 rotorcraft, Leonardo Helicopters with $ 806 million for 102 (first three-quarters only), Bell Helicopter with $ 696 million for 132, then Robinson Helicopter with $ 161 million for 305. By October 2018,

6431-555: The Stop-Rotor Rotary Wing Aircraft. The Australian company StopRotor Technology Pty Ltd has developed a prototype Hybrid RotorWing (HRW) craft. The design uses high alpha airflow to provide a symmetrical airflow across all the rotor blades, requiring it to drop almost vertically during transition. Inflight transition from fixed to rotary mode was demonstrated in August 2013. Another approach proposes

6540-417: The adverse effects of retreating blade stall of helicopters at higher airspeeds. A rotor kite or gyroglider is an unpowered rotary-wing aircraft. Like an autogyro or helicopter, it relies on lift created by one or more sets of rotors in order to fly. Unlike a helicopter, autogyros and rotor kites do not have an engine powering their rotors, but while an autogyro has an engine providing forward thrust that keeps

6649-549: The aircraft's handling properties under low airspeed conditions—it has proved advantageous to conduct tasks that were previously not possible with other aircraft, or were time- or work-intensive to accomplish on the ground. Today, helicopter uses include transportation of people and cargo, military uses, construction, firefighting, search and rescue , tourism , medical transport, law enforcement, agriculture, news and media , and aerial observation , among others. A helicopter used to carry loads connected to long cables or slings

SECTION 60

#1732794047219

6758-413: The airflow and forces the flow to move downward. This results in an equal and opposite force acting upward on the wing which is the lift force. The change of momentum of the airflow downward results in a reduction of the rearward momentum of the flow which is the result of a force acting forward on the airflow and applied by the wing to the air flow; an equal but opposite force acts on the wing rearward which

6867-407: The airplane produces lift, another drag component results. Induced drag , symbolized D i {\displaystyle D_{i}} , is due to a modification of the pressure distribution due to the trailing vortex system that accompanies the lift production. An alternative perspective on lift and drag is gained from considering the change of momentum of the airflow. The wing intercepts

6976-466: The aviation industry; and the turboshaft engine for helicopter use, pioneered in December 1951 by the aforementioned Kaman K-225, finally gave helicopters an engine with a large amount of power and a low weight penalty. Turboshafts are also more reliable than piston engines, especially when producing the sustained high levels of power required by a helicopter. The turboshaft engine was able to be scaled to

7085-434: The blades angle forwards or backwards, or left and right, to make the helicopter move in those directions. The anti-torque pedals are located in the same position as the rudder pedals in a fixed-wing aircraft, and serve a similar purpose, namely to control the direction in which the nose of the aircraft is pointed. Application of the pedal in a given direction changes the pitch of the tail rotor blades, increasing or reducing

7194-674: The building of roads. These operations are referred to as longline because of the long, single sling line used to carry the load. In military service helicopters are often useful for delivery of outsized slung loads that would not fit inside ordinary cargo aircraft: artillery pieces, large machinery (field radars, communications gear, electrical generators), or pallets of bulk cargo. In military operations these payloads are often delivered to remote locations made inaccessible by mountainous or riverine terrain, or naval vessels at sea. In electronic news gathering , helicopters have provided aerial views of some major news stories, and have been doing so, from

7303-453: The case of a wing , the reference areas are the same, and the drag force is in the same ratio as the lift force . Therefore, the reference for a wing is often the lifting area, sometimes referred to as "wing area" rather than the frontal area. For an object with a smooth surface, and non-fixed separation points (like a sphere or circular cylinder), the drag coefficient may vary with Reynolds number Re , up to extremely high values ( Re of

7412-405: The cockpit from overhead. The control is called the cyclic because it changes cyclic pitch of the main blades. The result is to tilt the rotor disk in a particular direction, resulting in the helicopter moving in that direction. If the pilot pushes the cyclic forward, the rotor disk tilts forward, and the rotor produces a thrust in the forward direction. If the pilot pushes the cyclic to the side,

7521-470: The cyclic, the collective, the anti-torque pedals, and the throttle. The cyclic control is usually located between the pilot's legs and is commonly called the cyclic stick or just cyclic . On most helicopters, the cyclic is similar to a joystick. However, the Robinson R22 and Robinson R44 have a unique teetering bar cyclic control system and a few helicopters have a cyclic control that descends into

7630-678: The drag coefficient C D {\displaystyle C_{\rm {D}}} as a function of Bejan number and the ratio between wet area A w {\displaystyle A_{\rm {w}}} and front area A f {\displaystyle A_{\rm {f}}} : C D = 2 A w A f B e R e L 2 {\displaystyle C_{\rm {D}}=2{\frac {A_{\rm {w}}}{A_{\rm {f}}}}{\frac {\mathrm {Be} }{\mathrm {Re} _{L}^{2}}}} where R e L {\displaystyle \mathrm {Re} _{L}}

7739-487: The drag coefficient approaches 24 R e {\displaystyle {\frac {24}{Re}}} ! In aerodynamics , aerodynamic drag , also known as air resistance , is the fluid drag force that acts on any moving solid body in the direction of the air's freestream flow. Alternatively, calculated from the flow field perspective (far-field approach), the drag force results from three natural phenomena: shock waves , vortex sheet, and viscosity . When

7848-620: The drag constant: b = 6 π η r {\displaystyle b=6\pi \eta r\,} where r {\displaystyle r} is the Stokes radius of the particle, and η {\displaystyle \eta } is the fluid viscosity. The resulting expression for the drag is known as Stokes' drag : F D = − 6 π η r v . {\displaystyle \mathbf {F} _{D}=-6\pi \eta r\,\mathbf {v} .} For example, consider

7957-533: The early 21st century, as well as recently weaponized utilities such as artillery spotting , aerial bombing and suicide attacks . The English word helicopter is adapted from the French word hélicoptère , coined by Gustave Ponton d'Amécourt in 1861, which originates from the Greek helix ( ἕλιξ ), genitive helikos (ἕλῐκος), "helix, spiral, whirl, convolution" and pteron ( πτερόν ) "wing". In

8066-489: The engine exhausts through an ordinary jet nozzle. Two Boeing X-50 Dragonfly prototypes with a two-bladed rotor were flown from 2003 but the program ended after both had crashed, having failed to transition successfully. In 2013 the US Naval Research Laboratory (NRL) published a vertical-to-horizontal flight transition method and associated technology, patented December 6, 2011, which they call

8175-438: The event was taken by Max Skladanowsky , but it remains lost . In 1885, Thomas Edison was given US$ 1,000 (equivalent to $ 34,000 today) by James Gordon Bennett, Jr. , to conduct experiments towards developing flight. Edison built a helicopter and used the paper for a stock ticker to create guncotton , with which he attempted to power an internal combustion engine. The helicopter was damaged by explosions and one of his workers

8284-485: The first half of the 20th century was that the amount of power produced by an engine was not able to overcome the engine's weight in vertical flight. This was overcome in early successful helicopters by using the smallest engines available. When the compact, flat engine was developed, the helicopter industry found a lighter-weight powerplant easily adapted to small helicopters, although radial engines continued to be used for larger helicopters. Turbine engines revolutionized

8393-441: The fluid is not moving relative to the currently used reference system, the power required to overcome the aerodynamic drag is given by: P D = F D ⋅ v = 1 2 ρ v 3 A C D {\displaystyle P_{D}=\mathbf {F} _{D}\cdot \mathbf {v} ={\tfrac {1}{2}}\rho v^{3}AC_{D}} The power needed to push an object through

8502-411: The following categories: The effect of streamlining on the relative proportions of skin friction and form drag is shown for two different body sections: An airfoil, which is a streamlined body, and a cylinder, which is a bluff body. Also shown is a flat plate illustrating the effect that orientation has on the relative proportions of skin friction, and pressure difference between front and back. A body

8611-448: The forces acting on the object beyond drag): 1 m ∑ F ( v ) − ρ A C D 2 m v 2 = d v d t . {\displaystyle {\frac {1}{m}}\sum F(v)-{\frac {\rho AC_{D}}{2m}}v^{2}={\frac {dv}{dt}}.\,} For a potato-shaped object of average diameter d and of density ρ obj , terminal velocity

8720-514: The high operating cost of helicopters cost-effective in ensuring that oil platforms continue to operate. Various companies specialize in this type of operation. NASA developed Ingenuity , a 1.8 kg (4.0 lb) helicopter used to survey Mars (along with a rover). It began service in February 2021 and was retired due to sustained rotor blade damage in January 2024 after 73 sorties. As

8829-478: The idea of vertical flight. In July 1754, Russian Mikhail Lomonosov had developed a small coaxial modeled after the Chinese top but powered by a wound-up spring device and demonstrated it to the Russian Academy of Sciences . It was powered by a spring, and was suggested as a method to lift meteorological instruments. In 1783, Christian de Launoy , and his mechanic , Bienvenu, used a coaxial version of

8938-504: The in-service and stored helicopter fleet of 38,570 with civil or government operators was led Robinson Helicopter with 24.7% followed by Airbus Helicopters with 24.4%, then Bell with 20.5 and Leonardo with 8.4%, Russian Helicopters with 7.7%, Sikorsky Aircraft with 7.2%, MD Helicopters with 3.4% and other with 2.2%. The most widespread model is the piston Robinson R44 with 5,600, then the H125/ AS350 with 3,600 units, followed by

9047-661: The lack of an airstrip would make transport via fixed-wing aircraft impossible. The use of transport helicopters to deliver troops as an attack force on an objective is referred to as " air assault ". Unmanned aerial systems (UAS) helicopter systems of varying sizes are developed by companies for military reconnaissance and surveillance duties. Naval forces also use helicopters equipped with dipping sonar for anti-submarine warfare , since they can operate from small ships. Oil companies charter helicopters to move workers and parts quickly to remote drilling sites located at sea or in remote locations. The speed advantage over boats makes

9156-578: The late 1960s. Helicopters have also been used in films, both in front and behind the camera. The largest single non-combat helicopter operation in history was the disaster management operation following the 1986 Chernobyl nuclear disaster . Hundreds of pilots were involved in airdrop and observation missions, making dozens of sorties a day for several months. " Helitack " is the use of helicopters to combat wildland fires . The helicopters are used for aerial firefighting (water bombing) and may be fitted with tanks or carry helibuckets . Helibuckets, such as

9265-554: The limited power did not allow for manned flight. The introduction of the internal combustion engine at the end of the 19th century became the watershed for helicopter development as engines began to be developed and produced that were powerful enough to allow for helicopters able to lift humans. Early helicopter designs utilized custom-built engines or rotary engines designed for airplanes, but these were soon replaced by more powerful automobile engines and radial engines . The single, most-limiting factor of helicopter development during

9374-485: The monorotor design, and coaxial-rotor , tiltrotor and compound helicopters are also all flying today. Four-rotor helicopters ( quadcopters ) were pioneered as early as 1907 in France, and along with other types of multicopters , have been developed mainly for specialized applications such as commercial unmanned aerial vehicles (drones) due to the rapid expansion of drone racing and aerial photography markets in

9483-598: The nearby park, the Parco Forlanini. Emmanuel Dieuaide's steam-powered design featured counter-rotating rotors powered through a hose from a boiler on the ground. In 1887 Parisian inventor, Gustave Trouvé , built and flew a tethered electric model helicopter. In July 1901, the maiden flight of Hermann Ganswindt 's helicopter took place in Berlin-Schöneberg; this was probably the first heavier-than-air motor-driven flight carrying humans. A movie covering

9592-464: The nose to pitch down, with a resultant increase in airspeed and loss of altitude. Aft cyclic will cause the nose to pitch up, slowing the helicopter and causing it to climb. Increasing collective (power) while maintaining a constant airspeed will induce a climb while decreasing collective will cause a descent. Coordinating these two inputs, down collective plus aft cyclic or up collective plus forward cyclic, will result in airspeed changes while maintaining

9701-410: The power normally required to be diverted for the tail rotor to be applied fully to the main rotors, increasing the aircraft's power efficiency and lifting capacity. There are several common configurations that use the counter-rotating effect to benefit the rotorcraft: Tip jet designs let the rotor push itself through the air and avoid generating torque. The number, size and type of engine(s) used on

9810-404: The result of the creation of lift on a three-dimensional lifting body , such as the wing or propeller of an airplane. Induced drag consists primarily of two components: drag due to the creation of trailing vortices ( vortex drag ); and the presence of additional viscous drag ( lift-induced viscous drag ) that is not present when lift is zero. The trailing vortices in the flow-field, present in

9919-435: The rotor disk tilts to that side and produces thrust in that direction, causing the helicopter to hover sideways. The collective pitch control or collective is located on the left side of the pilot's seat with a settable friction control to prevent inadvertent movement. The collective changes the pitch angle of all the main rotor blades collectively (i.e. all at the same time) and independently of their position. Therefore, if

10028-415: The rotor for forward flight so that it then acts as a fixed wing. For vertical flight and hovering it spins to act as a rotary wing or rotor, and for forward flight at speed it stops to act as a fixed wing providing some or all of the lift required. Additional fixed wings may also be provided to help with stability and control and to provide auxiliary lift. An early American proposal was the conversion of

10137-405: The rotor in cruise, which allows its rotation to be slowed down , thus increasing the maximum speed of the aircraft. The Lockheed AH-56A Cheyenne diverted up to 90% of its engine power to a pusher propeller during forward flight. There are three basic flight conditions for a helicopter: hover, forward flight and the transition between the two. Hovering is the most challenging part of flying

10246-420: The rotor throughout normal flight. The rotor system, or more simply rotor , is the rotating part of a helicopter that generates lift . A rotor system may be mounted horizontally, as main rotors are, providing lift vertically, or it may be mounted vertically, such as a tail rotor, to provide horizontal thrust to counteract torque from the main rotors. The rotor consists of a mast, hub and rotor blades. The mast

10355-434: The rotor turning, a rotor kite has no engine at all, and relies on either being carried aloft and dropped from another aircraft, or by being towed into the air behind a car or boat. A rotary wing is characterised by the number of blades . Typically this is between two and six per driveshaft. A rotorcraft may have one or more rotors. Various rotor configurations have been used: Some rotary wing aircraft are designed to stop

10464-408: The shape of the object and on the Reynolds number R e = v D ν = ρ v D μ , {\displaystyle \mathrm {Re} ={\frac {vD}{\nu }}={\frac {\rho vD}{\mu }},} where At low R e {\displaystyle \mathrm {Re} } , C D {\displaystyle C_{\rm {D}}}

10573-417: The size of the helicopter being designed, so that all but the lightest of helicopter models are powered by turbine engines today. Special jet engines developed to drive the rotor from the rotor tips are referred to as tip jets . Tip jets powered by a remote compressor are referred to as cold tip jets, while those powered by combustion exhaust are referred to as hot tip jets. An example of a cold jet helicopter

10682-483: The skies. Since helicopters can achieve a unique aerial view, they are often used in conjunction with police on the ground to report on suspects' locations and movements. They are often mounted with lighting and heat-sensing equipment for night pursuits. Military forces use attack helicopters to conduct aerial attacks on ground targets. Such helicopters are mounted with missile launchers and miniguns . Transport helicopters are used to ferry troops and supplies where

10791-808: The speed, the work (resulting in displacement over a fixed distance) is done twice as fast. Since power is the rate of doing work, 4 times the work done in half the time requires 8 times the power. When the fluid is moving relative to the reference system, for example, a car driving into headwind, the power required to overcome the aerodynamic drag is given by the following formula: P D = F D ⋅ v o = 1 2 C D A ρ ( v w + v o ) 2 v o {\displaystyle P_{D}=\mathbf {F} _{D}\cdot \mathbf {v_{o}} ={\tfrac {1}{2}}C_{D}A\rho (v_{w}+v_{o})^{2}v_{o}} Where v w {\displaystyle v_{w}}

10900-884: The square of the speed at low Reynolds numbers, and as the cube of the speed at high numbers. It can be demonstrated that drag force can be expressed as a function of a dimensionless number, which is dimensionally identical to the Bejan number . Consequently, drag force and drag coefficient can be a function of Bejan number. In fact, from the expression of drag force it has been obtained: F d = Δ p A w = 1 2 C D A f ν μ l 2 R e L 2 {\displaystyle F_{\rm {d}}=\Delta _{\rm {p}}A_{\rm {w}}={\frac {1}{2}}C_{\rm {D}}A_{\rm {f}}{\frac {\nu \mu }{l^{2}}}\mathrm {Re} _{L}^{2}} and consequently allows expressing

11009-478: The tail rotor, such as the ducted fan (called Fenestron or FANTAIL ) and NOTAR . NOTAR provides anti-torque similar to the way a wing develops lift through the use of the Coandă effect on the tail boom. The use of two or more horizontal rotors turning in opposite directions is another configuration used to counteract the effects of torque on the aircraft without relying on an anti-torque tail rotor. This allows

11118-482: The terminal velocity v t = ( ρ − ρ 0 ) V g b {\displaystyle v_{t}={\frac {(\rho -\rho _{0})Vg}{b}}} . For a given b {\displaystyle b} , denser objects fall more quickly. For the special case of small spherical objects moving slowly through a viscous fluid (and thus at small Reynolds number), George Gabriel Stokes derived an expression for

11227-447: The throttle is to maintain enough engine power to keep the rotor RPM within allowable limits so that the rotor produces enough lift for flight. In single-engine helicopters, the throttle control is a motorcycle-style twist grip mounted on the collective control, while dual-engine helicopters have a power lever for each engine. A compound helicopter has an additional system for thrust and, typically, small stub fixed wings . This offloads

11336-411: The thrust produced by the tail rotor and causing the nose to yaw in the direction of the applied pedal. The pedals mechanically change the pitch of the tail rotor altering the amount of thrust produced. Helicopter rotors are designed to operate in a narrow range of RPM . The throttle controls the power produced by the engine, which is connected to the rotor by a fixed ratio transmission. The purpose of

11445-489: The velocity function is defined in terms of the hyperbolic cotangent function: v ( t ) = v t coth ⁡ ( t g v t + coth − 1 ⁡ ( v i v t ) ) . {\displaystyle v(t)=v_{t}\coth \left(t{\frac {g}{v_{t}}}+\coth ^{-1}\left({\frac {v_{i}}{v_{t}}}\right)\right).\,} The hyperbolic cotangent also has

11554-570: The vertical flight he had envisioned. Steam power was popular with other inventors as well. In 1877, the Italian engineer, inventor and aeronautical pioneer Enrico Forlanini developed an unmanned helicopter powered by a steam engine . It rose to a height of 13 meters (43 feet), where it remained for 20 seconds, after a vertical take-off from a park in Milan . Milan has dedicated its city airport to Enrico Forlanini, also named Linate Airport , as well as

11663-405: The wake of a lifting body, derive from the turbulent mixing of air from above and below the body which flows in slightly different directions as a consequence of creation of lift . With other parameters remaining the same, as the lift generated by a body increases, so does the lift-induced drag. This means that as the wing's angle of attack increases (up to a maximum called the stalling angle),

11772-484: Was badly burned. Edison reported that it would take a motor with a ratio of three to four pounds per horsepower produced to be successful, based on his experiments. Ján Bahýľ , a Slovak inventor, adapted the internal combustion engine to power his helicopter model that reached a height of 0.5 meters (1.6 feet) in 1901. On 5 May 1905, his helicopter reached 4 meters (13 feet) in altitude and flew for over 1,500 meters (4,900 feet). In 1908, Edison patented his own design for

11881-417: Was invented in 1920 by Juan de la Cierva . The autogyro with pusher propeller was first tested by Etienne Dormoy with his Buhl A-1 Autogyro . The rotor of a gyrodyne is normally driven by its engine for takeoff and landing – hovering like a helicopter – with anti-torque and propulsion for forward flight provided by one or more propellers mounted on short or stub wings. As power

#218781