Misplaced Pages

#681318

70-554: The NPO Saturn AL-55 is a high performance turbofan engine manufactured by NPO Saturn Russia, for powering advanced trainers, unmanned aerial vehicles (UAV) and light attack aircraft. A variant of the AL-55I powers the HAL HJT-36 Sitara Indian jet trainer. The design comprises five main features. It has a three-stage low pressure compressor, five stage high pressure chamber, an annular combustion chamber and

140-426: A cylindrical duct or shroud. Other terms include ducted propeller or shrouded propeller . When used in vertical takeoff and landing ( VTOL ) applications it is also known as a shrouded rotor . Ducted fans are used for propulsion or direct lift in many types of vehicle including aeroplanes , airships , hovercraft , and powered lift VTOL aircraft. The high-bypass turbofan engines used on many modern airliners

210-419: A discordant nature known as "buzz saw" noise. All modern turbofan engines have acoustic liners in the nacelle to damp their noise. They extend as much as possible to cover the largest surface area. The acoustic performance of the engine can be experimentally evaluated by means of ground tests or in dedicated experimental test rigs. In the aerospace industry, chevrons are the "saw-tooth" patterns on

280-410: A fixed total applied fuel:air ratio, the total fuel flow for a given fan airflow will be the same, regardless of the dry specific thrust of the engine. However, a high specific thrust turbofan will, by definition, have a higher nozzle pressure ratio, resulting in a higher afterburning net thrust and, therefore, a lower afterburning specific fuel consumption (SFC). However, high specific thrust engines have

350-426: A high dry SFC. The situation is reversed for a medium specific thrust afterburning turbofan: i.e., poor afterburning SFC/good dry SFC. The former engine is suitable for a combat aircraft which must remain in afterburning combat for a fairly long period, but has to fight only fairly close to the airfield (e.g. cross border skirmishes). The latter engine is better for an aircraft that has to fly some distance, or loiter for

420-416: A higher nozzle pressure ratio than the turbojet, but with a lower exhaust temperature to retain net thrust. Since the temperature rise across the whole engine (intake to nozzle) would be lower, the (dry power) fuel flow would also be reduced, resulting in a better specific fuel consumption (SFC). Some low-bypass ratio military turbofans (e.g. F404 , JT8D ) have variable inlet guide vanes to direct air onto

490-590: A long time, before going into combat. However, the pilot can afford to stay in afterburning only for a short period, before aircraft fuel reserves become dangerously low. The first production afterburning turbofan engine was the Pratt & Whitney TF30 , which initially powered the F-111 Aardvark and F-14 Tomcat . Low-bypass military turbofans include the Pratt & Whitney F119 , the Eurojet EJ200 ,

560-401: A pound of thrust, more fuel is wasted in the faster propelling jet. In other words, the independence of thermal and propulsive efficiencies, as exists with the piston engine/propeller combination which preceded the turbojet, is lost. In contrast, Roth considers regaining this independence the single most important feature of the turbofan which allows specific thrust to be chosen independently of

630-403: A pure-jet of the same thrust, and jet noise is no longer the predominant source. Turbofan engine noise propagates both upstream via the inlet and downstream via the primary nozzle and the by-pass duct. Other noise sources are the fan, compressor and turbine. Modern commercial aircraft employ high-bypass-ratio (HBPR) engines with separate flow, non-mixing, short-duct exhaust systems. Their noise

700-598: A single stage high and low pressure turbines. In August 2005, the Russian export organization known as Rosoboronexport and India's Hindustan Aeronautics Limited (HAL) signed an agreement for the licensed production of up to 1,000 AL-55I engines. The agreement includes a firm order for 250 engines to be manufactured at HAL facilities in India, to power both HAL HJT-36 trainer and HAL HJT 39 combat trainer aircraft. Data from UEC Saturn . Turbofan The ratio of

770-569: A static thrust of 4,320 lb (1,960 kg), and had a bypass ratio of 6:1. The General Electric TF39 became the first production model, designed to power the Lockheed C-5 Galaxy military transport aircraft. The civil General Electric CF6 engine used a derived design. Other high-bypass turbofans are the Pratt & Whitney JT9D , the three-shaft Rolls-Royce RB211 and the CFM International CFM56 ; also

SECTION 10

#1732794179682

840-473: A turbofan engine is the ratio between the mass flow rate of the bypass stream to the mass flow rate entering the core. A bypass ratio of 6, for example, means that 6 times more air passes through the bypass duct than the amount that passes through the combustion chamber. Turbofan engines are usually described in terms of BPR, which together with overall pressure ratio, turbine inlet temperature and fan pressure ratio are important design parameters. In addition BPR

910-421: A turbojet engine uses all of the engine's output to produce thrust in the form of a hot high-velocity exhaust gas jet, a turbofan's cool low-velocity bypass air yields between 30% and 70% of the total thrust produced by a turbofan system. The thrust ( F N ) generated by a turbofan depends on the effective exhaust velocity of the total exhaust, as with any jet engine, but because two exhaust jets are present

980-496: A turbojet even though an extra turbine, a gearbox and a propeller are added to the turbojet's low-loss propelling nozzle. The turbofan has additional losses from its greater number of compressor stages/blades, fan and bypass duct. Froude, or propulsive, efficiency can be defined as: η f = 2 1 + V j V a {\displaystyle \eta _{f}={\frac {2}{1+{\frac {V_{j}}{V_{a}}}}}} where: While

1050-704: A turbojet which accelerates a smaller amount more quickly, which is a less efficient way to generate the same thrust (see the efficiency section below). The ratio of the mass-flow of air bypassing the engine core compared to the mass-flow of air passing through the core is referred to as the bypass ratio . Engines with more jet thrust relative to fan thrust are known as low-bypass turbofans , those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are high-bypass, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofans on combat aircraft. The bypass ratio (BPR) of

1120-419: Is an aerodynamic ring which surrounds the fan and closely fits the blade tips. It must be made rigid enough not to distort under flight loads nor touch the blades as they turn. The duct performs several functions: Principally, it reduces the vortices created by air flowing round the ends of the blades. This reduces the aerodynamic losses or drag, thus increasing the overall efficiency of the fan. Because of this,

1190-401: Is an example of a very successful and popular use of ducted fan design. The duct increases thrust efficiency by up to 90% in most cases , in comparison to a similar-sized propeller in free air. Ducted fans are quieter, and offer good opportunities for thrust vectoring. The shroud offers good protection to ground personnel from accidentally contacting the spinning blades, as well as protecting

1260-507: Is best suited to high supersonic speeds. If it is all transferred to a separate big mass of air with low kinetic energy, the aircraft is best suited to zero speed (hovering). For speeds in between, the gas power is shared between a separate airstream and the gas turbine's own nozzle flow in a proportion which gives the aircraft performance required. The trade off between mass flow and velocity is also seen with propellers and helicopter rotors by comparing disc loading and power loading. For example,

1330-410: Is considerable potential for reducing fuel consumption for the same core cycle by increasing BPR.This is achieved because of the reduction in pounds of thrust per lb/sec of airflow (specific thrust) and the resultant reduction in lost kinetic energy in the jets (increase in propulsive efficiency). If all the gas power from a gas turbine is converted to kinetic energy in a propelling nozzle, the aircraft

1400-430: Is due to the speed, temperature, and pressure of the exhaust jet, especially during high-thrust conditions, such as those required for takeoff. The primary source of jet noise is the turbulent mixing of shear layers in the engine's exhaust. These shear layers contain instabilities that lead to highly turbulent vortices that generate the pressure fluctuations responsible for sound. To reduce the noise associated with jet flow,

1470-413: Is quoted for turboprop and unducted fan installations because their high propulsive efficiency gives them the overall efficiency characteristics of very high bypass turbofans. This allows them to be shown together with turbofans on plots which show trends of reducing specific fuel consumption (SFC) with increasing BPR. BPR can also be quoted for lift fan installations where the fan airflow is remote from

SECTION 20

#1732794179682

1540-420: Is sufficient core power to drive the fan. A smaller core flow/higher bypass ratio cycle can be achieved by raising the inlet temperature of the high-pressure (HP) turbine rotor. To illustrate one aspect of how a turbofan differs from a turbojet, comparisons can be made at the same airflow (to keep a common intake for example) and the same net thrust (i.e. same specific thrust). A bypass flow can be added only if

1610-424: Is that combustion is less efficient at lower speeds. Any action to reduce the fuel consumption of the engine by increasing its pressure ratio or turbine temperature to achieve better combustion causes a corresponding increase in pressure and temperature in the exhaust duct which in turn cause a higher gas speed from the propelling nozzle (and higher KE and wasted fuel). Although the engine would use less fuel to produce

1680-411: Is very fuel intensive. Consequently, afterburning can be used only for short portions of a mission. Unlike in the main engine, where stoichiometric temperatures in the combustor have to be reduced before they reach the turbine, an afterburner at maximum fuelling is designed to produce stoichiometric temperatures at entry to the nozzle, about 2,100 K (3,800 °R; 3,300 °F; 1,800 °C). At

1750-479: The Bristol Olympus , and Pratt & Whitney JT3C engines, increased the overall pressure ratio and thus the thermodynamic efficiency of engines. They also had poor propulsive efficiency, because pure turbojets have a high specific thrust/high velocity exhaust, which is better suited to supersonic flight. The original low-bypass turbofan engines were designed to improve propulsive efficiency by reducing

1820-702: The General Electric F110 , the Klimov RD-33 , and the Saturn AL-31 , all of which feature a mixed exhaust, afterburner and variable area propelling nozzle. To further improve fuel economy and reduce noise, almost all jet airliners and most military transport aircraft (e.g., the C-17 ) are powered by low-specific-thrust/high-bypass-ratio turbofans. These engines evolved from the high-specific-thrust/low-bypass-ratio turbofans used in such aircraft in

1890-604: The Lockheed Martin F-35 Lightning II , and other low-speed designs such as hovercraft for their higher thrust-to-weight ratio. In some cases, a shrouded rotor can be 94% more efficient than an open rotor. The improved performance is mainly because the outward flow is less contracted and thus carries more kinetic energy. Among model aircraft hobbyists, the ducted fan is popular with builders of high-performance radio controlled model aircraft . Glow plug engines combined with ducted-fan units were

1960-421: The 1960s. Modern combat aircraft tend to use low-bypass ratio turbofans, and some military transport aircraft use turboprops . Low specific thrust is achieved by replacing the multi-stage fan with a single-stage unit. Unlike some military engines, modern civil turbofans lack stationary inlet guide vanes in front of the fan rotor. The fan is scaled to achieve the desired net thrust. The core (or gas generator) of

2030-464: The aerospace industry has sought to disrupt shear layer turbulence and reduce the overall noise produced. Fan noise may come from the interaction of the fan-blade wakes with the pressure field of the downstream fan-exit stator vanes. It may be minimized by adequate axial spacing between blade trailing edge and stator entrance. At high engine speeds, as at takeoff, shock waves from the supersonic fan tips, because of their unequal nature, produce noise of

2100-422: The afterburner, raising the temperature of exhaust gases by a significant degree, resulting in a higher exhaust velocity/engine specific thrust. The variable geometry nozzle must open to a larger throat area to accommodate the extra volume and increased flow rate when the afterburner is lit. Afterburning is often designed to give a significant thrust boost for take off, transonic acceleration and combat maneuvers, but

2170-441: The aircraft is going forwards, leaving a very fast wake. This wake contains kinetic energy that reflects the fuel used to produce it, rather than the fuel used to move the aircraft forwards. A turbofan harvests that wasted velocity and uses it to power a ducted fan that blows air in bypass channels around the rest of the turbine. This reduces the speed of the propelling jet while pushing more air, and thus more mass. The other penalty

NPO Saturn AL-55 - Misplaced Pages Continue

2240-474: The average stage loading and to maintain LP turbine efficiency. Reducing core flow also increases bypass ratio. Bypass ratios greater than 5:1 are increasingly common; the Pratt & Whitney PW1000G , which entered commercial service in 2016, attains 12.5:1. Further improvements in core thermal efficiency can be achieved by raising the overall pressure ratio of the core. Improvements in blade aerodynamics can reduce

2310-469: The better high-speed performance of a low bypass ratio turbofan with a smaller fan diameter. However, a ducted fan may be powered by any source of shaft power such as a reciprocating engine , Wankel engine , or electric motor . A kind of ducted fan, known as a fantail or by the trademark name Fenestron , is also used to replace tail rotors on helicopters . Ducted fans are favored in VTOL aircraft such as

2380-483: The blades from damage during such an impact. The reduced tip vortices also mean that the fan wake is less turbulent. With careful design, the heated discharge from the engine cooling system can be injected into the low-turbulence fan wake to increase thrust. A ducted fan may be powered by any kind of motor capable of turning the fan. Examples include piston, rotary (Wankel), and turboshaft combustion engines, as well as electric motors. The fan may be mounted directly on

2450-510: The blades themselves from external debris or objects. By varying the cross-section of the duct the designer can advantageously affect the velocity and pressure of the airflow according to Bernoulli's principle . Drawbacks include increased weight due to the added structure of the shroud, a need for precision in tolerances of blade-tip to shroud clearance, a need for better vibration control compared to free-air propellers, and complex duct design requirements. Lastly, when at high angles of attack,

2520-448: The engine and doesn't flow past the engine core. Considering a constant core (i.e. fixed pressure ratio and turbine inlet temperature), core and bypass jet velocities equal and a particular flight condition (i.e. Mach number and altitude) the fuel consumption per lb of thrust (sfc) decreases with increase in BPR. At the same time gross and net thrusts increase, but by different amounts. There

2590-427: The engine must generate enough power to drive the fan at its rated mass flow and pressure ratio. Improvements in turbine cooling/material technology allow for a higher (HP) turbine rotor inlet temperature, which allows a smaller (and lighter) core, potentially improving the core thermal efficiency. Reducing the core mass flow tends to increase the load on the LP turbine, so this unit may require additional stages to reduce

2660-416: The engine, from the gas generator, to a ducted fan which produces a second, additional mass of accelerated air. The transfer of energy from the core to bypass air results in lower pressure and temperature gas entering the core nozzle (lower exhaust velocity), and fan-produced higher pressure and temperature bypass-air entering the fan nozzle. The amount of energy transferred depends on how much pressure rise

2730-524: The exhaust velocity to a value closer to that of the aircraft. The Rolls-Royce Conway , the world's first production turbofan, had a bypass ratio of 0.3, similar to the modern General Electric F404 fighter engine. Civilian turbofan engines of the 1960s, such as the Pratt & Whitney JT8D and the Rolls-Royce Spey , had bypass ratios closer to 1 and were similar to their military equivalents. The first Soviet airliner powered by turbofan engines

2800-404: The fan can either be used to provide increased thrust and aircraft performance, or be made smaller than the equivalent free propeller. It provides acoustic shielding which, together with the reduced energy waste, significantly cuts noise emissions from the propeller. It acts as a protective device, both to protect objects such as ground staff from being hit by the whirling blades, and to protect

2870-411: The fan is designed to produce (fan pressure ratio). The best energy exchange (lowest fuel consumption) between the two flows, and how the jet velocities compare, depends on how efficiently the transfer takes place which depends on the losses in the fan-turbine and fan. The fan flow has lower exhaust velocity, giving much more thrust per unit energy (lower specific thrust ). Both airstreams contribute to

NPO Saturn AL-55 - Misplaced Pages Continue

2940-437: The first achievable means of modeling a scaled-size jet aircraft. Despite the introduction of model-scale turbojet engines, electric-powered ducted fans remain popular on smaller, lower-cost model aircraft. Some electric-powered ducted fan airplanes can reach speeds of more than 320km/h (200mph). Most cooling fans used in computers contain a duct integrated into the fan assembly; the duct is also used for mechanically mounting

3010-450: The first fan rotor stage. This improves the fan surge margin (see compressor map ). Since the 1970s, most jet fighter engines have been low/medium bypass turbofans with a mixed exhaust, afterburner and variable area exit nozzle. An afterburner is a combustor located downstream of the turbine blades and directly upstream of the nozzle, which burns fuel from afterburner-specific fuel injectors. When lit, large volumes of fuel are burnt in

3080-483: The fuel consumption of the turbojet. It achieves this by pushing more air, thus increasing the mass and lowering the speed of the propelling jet compared to that of the turbojet. This is done mechanically by adding a ducted fan rather than using viscous forces. A vacuum ejector is used in conjunction with the fan as first envisaged by inventor Frank Whittle . Whittle envisioned flight speeds of 500 mph in his March 1936 UK patent 471,368 "Improvements relating to

3150-400: The gas generator cycle. The working substance of the thermodynamic cycle is the only mass accelerated to produce thrust in a turbojet which is a serious limitation (high fuel consumption) for aircraft speeds below supersonic. For subsonic flight speeds the speed of the propelling jet has to be reduced because there is a price to be paid in producing the thrust. The energy required to accelerate

3220-443: The gas inside the engine (increase in kinetic energy) is expended in two ways, by producing a change in momentum ( i.e. a force), and a wake which is an unavoidable consequence of producing thrust by an airbreathing engine (or propeller). The wake velocity, and fuel burned to produce it, can be reduced and the required thrust still maintained by increasing the mass accelerated. A turbofan does this by transferring energy available inside

3290-429: The gross thrust of the engine. The additional air for the bypass stream increases the ram drag in the air intake stream-tube, but there is still a significant increase in net thrust. The overall effective exhaust velocity of the two exhaust jets can be made closer to a normal subsonic aircraft's flight speed and gets closer to the ideal Froude efficiency . A turbofan accelerates a larger mass of air more slowly, compared to

3360-409: The high-bypass type, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofan engines with bypass and core mixing before the afterburner. Modern turbofans have either a large single-stage fan or a smaller fan with several stages. An early configuration combined a low-pressure turbine and fan in a single rear-mounted unit. The turbofan was invented to improve

3430-474: The hot nozzle to convert to kinetic energy. Turbofans represent an intermediate stage between turbojets , which derive all their thrust from exhaust gases, and turbo-props which derive minimal thrust from exhaust gases (typically 10% or less). Extracting shaft power and transferring it to a bypass stream introduces extra losses which are more than made up by the improved propulsive efficiency. The turboprop at its best flight speed gives significant fuel savings over

3500-468: The mass-flow of air bypassing the engine core to the mass-flow of air passing through the core is referred to as the bypass ratio . The engine produces thrust through a combination of these two portions working together. Engines that use more jet thrust relative to fan thrust are known as low-bypass turbofans ; conversely those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are of

3570-417: The mechanical power produced by the turbine. In a bypass design, extra turbines drive a ducted fan that accelerates air rearward from the front of the engine. In a high-bypass design, the ducted fan and nozzle produce most of the thrust. Turbofans are closely related to turboprops in principle because both transfer some of the gas turbine's gas power, using extra machinery, to a bypass stream leaving less for

SECTION 50

#1732794179682

3640-539: The number of extra compressor stages required, and variable geometry stators enable high-pressure-ratio compressors to work surge-free at all throttle settings. The first (experimental) high-bypass turbofan engine was the AVCO-Lycoming PLF1A-2, a Honeywell T55 turboshaft-derived engine that was first run in February 1962. The PLF1A-2 had a 40 in diameter (100 cm) geared fan stage, produced

3710-448: The powerplant output shaft, or driven remotely via an extended drive shaft and gearing. In the remote arrangement, several fans may be driven by a single powerplant. An assembly designed throughout as a single integrated unit is referred to as a fan pod or ducted propulsor. An advantage of the pod approach is that the design of each component can be matched to the others, helping to maximise performance and minimise weight. It also eases

3780-414: The propulsion of aircraft", in which he describes the principles behind the turbofan, although not called as such at that time. While the turbojet uses the gas from its thermodynamic cycle as its propelling jet, for aircraft speeds below 500 mph there are two penalties to this design which are addressed by the turbofan. Firstly, energy is wasted as the propelling jet is going much faster rearwards than

3850-399: The same helicopter weight can be supported by a high power engine and small diameter rotor or, for less fuel, a lower power engine and bigger rotor with lower velocity through the rotor. Bypass usually refers to transferring gas power from a gas turbine to a bypass stream of air to reduce fuel consumption and jet noise. Alternatively, there may be a requirement for an afterburning engine where

3920-660: The shroud can stall and produce high drag. A ducted fan has three main components; the fan or propeller which provides thrust or lift, the duct or shroud which surrounds the fan, and the engine or motor which powers the fan. Like any other fan, propeller or rotor, a ducted fan is characterised by the number of blades. The Rhein Flugzeugbau (RFB) SG 85 had three blades, while the Dowty Rotol Ducted Propulsor had seven. The blades may be of fixed or variable pitch. See: Fan (machine) The duct or shroud

3990-587: The smaller TF34 . More recent large high-bypass turbofans include the Pratt & Whitney PW4000 , the three-shaft Rolls-Royce Trent , the General Electric GE90 / GEnx and the GP7000 , produced jointly by GE and P&W. The Pratt & Whitney JT9D engine was the first high bypass ratio jet engine to power a wide-body airliner. Ducted fan In aeronautics, a ducted fan is a thrust-generating mechanical fan or propeller mounted within

4060-502: The sole requirement for bypass is to provide cooling air. This sets the lower limit for BPR and these engines have been called "leaky" or continuous bleed turbojets (General Electric YJ-101 BPR 0.25) and low BPR turbojets (Pratt & Whitney PW1120). Low BPR (0.2) has also been used to provide surge margin as well as afterburner cooling for the Pratt & Whitney J58 . Propeller engines are most efficient for low speeds, turbojet engines for high speeds, and turbofan engines between

4130-536: The technology and materials available at the time. The first turbofan engine, which was only run on a test bed, was the German Daimler-Benz DB 670 , designated the 109-007 by the German RLM ( Ministry of Aviation ), with a first run date of 27 May 1943, after the testing of the turbomachinery using an electric motor, which had been undertaken on 1 April 1943. Development of the engine

4200-497: The thrust equation can be expanded as: F N = m ˙ e v h e − m ˙ o v o + B P R ( m ˙ c ) v f {\displaystyle F_{N}={\dot {m}}_{e}v_{he}-{\dot {m}}_{o}v_{o}+BPR\,({\dot {m}}_{c})v_{f}} where: The cold duct and core duct's nozzle systems are relatively complex due to

4270-673: The trailing edges of some jet engine nozzles that are used for noise reduction . The shaped edges smooth the mixing of hot air from the engine core and cooler air flowing through the engine fan, which reduces noise-creating turbulence. Chevrons were developed by GE under a NASA contract. Some notable examples of such designs are Boeing 787 and Boeing 747-8  – on the Rolls-Royce Trent 1000 and General Electric GEnx engines. Early turbojet engines were not very fuel-efficient because their overall pressure ratio and turbine inlet temperature were severely limited by

SECTION 60

#1732794179682

4340-428: The turbine inlet temperature is not too high to compensate for the smaller core flow. Future improvements in turbine cooling/material technology can allow higher turbine inlet temperature, which is necessary because of increased cooling air temperature, resulting from an overall pressure ratio increase. The resulting turbofan, with reasonable efficiencies and duct loss for the added components, would probably operate at

4410-476: The two flows may combine within the ducts, and share a common nozzle, which can be fitted with afterburner. Most of the air flow through a high-bypass turbofan is lower-velocity bypass flow: even when combined with the much-higher-velocity engine exhaust, the average exhaust velocity is considerably lower than in a pure turbojet. Turbojet engine noise is predominately jet noise from the high exhaust velocity. Therefore, turbofan engines are significantly quieter than

4480-418: The two. Turbofans are the most efficient engines in the range of speeds from about 500 to 1,000 km/h (270 to 540 kn; 310 to 620 mph), the speed at which most commercial aircraft operate. In a turbojet (zero-bypass) engine, the high temperature and high pressure exhaust gas is accelerated when it undergoes expansion through a propelling nozzle and produces all the thrust. The compressor absorbs

4550-510: The use of two separate exhaust flows. In high bypass engines, the fan is situated in a short duct near the front of the engine and typically has a convergent cold nozzle, with the tail of the duct forming a low pressure ratio nozzle that under normal conditions will choke creating supersonic flow patterns around the core . The core nozzle is more conventional, but generates less of the thrust, and depending on design choices, such as noise considerations, may conceivably not choke. In low bypass engines

4620-536: The vehicle designer's task of integration with the vehicle and its systems. In aircraft applications, the operating speed of an unshrouded propeller is limited since tip speeds approach the sound barrier at lower speeds than an equivalent ducted fan. The most common ducted fan arrangement used in full-sized aircraft is a turbofan engine, where the power to turn the fan is provided by a gas turbine . High bypass ratio turbofan engines are used on nearly all civilian airliners , while military fighters usually make use of

4690-701: The world, with an experience base of over 10 million service hours. The CF700 turbofan engine was also used to train Moon-bound astronauts in Project Apollo as the powerplant for the Lunar Landing Research Vehicle . A high-specific-thrust/low-bypass-ratio turbofan normally has a multi-stage fan behind inlet guide vanes, developing a relatively high pressure ratio and, thus, yielding a high (mixed or cold) exhaust velocity. The core airflow needs to be large enough to ensure there

4760-614: Was abandoned with its problems unsolved, as the war situation worsened for Germany. Later in 1943, the British ground tested the Metrovick F.3 turbofan, which used the Metrovick F.2 turbojet as a gas generator with the exhaust discharging into a close-coupled aft-fan module comprising a contra-rotating LP turbine system driving two co-axial contra-rotating fans. Improved materials, and the introduction of twin compressors, such as in

4830-660: Was derived from the General Electric J85/CJ610 turbojet 2,850 lbf (12,700 N) to power the larger Rockwell Sabreliner 75/80 model aircraft, as well as the Dassault Falcon 20 , with about a 50% increase in thrust to 4,200 lbf (19,000 N). The CF700 was the first small turbofan to be certified by the Federal Aviation Administration (FAA). There were at one time over 400 CF700 aircraft in operation around

4900-587: Was the Tupolev Tu-124 introduced in 1962. It used the Soloviev D-20 . 164 aircraft were produced between 1960 and 1965 for Aeroflot and other Eastern Bloc airlines, with some operating until the early 1990s. The first General Electric turbofan was the aft-fan CJ805-23 , based on the CJ805-3 turbojet. It was followed by the aft-fan General Electric CF700 engine, with a 2.0 bypass ratio. This

#681318