The Piper PA-11 Cub Special is a later-production variant of the J-3 Cub manufactured by Piper Aircraft .
66-417: The PA-11 is a high-wing braced cabin monoplane with a tail-wheel landing gear . The enclosed cabin has two tandem seats. Early PA-11s had a Continental A65-8 engine, while the later ones had the option of a Continental C90-8 . The PA-11 was based on the earlier J-3, but with the engine cowling fully enclosed (as on the earlier J-5 ), the windshield sloped at a shallower angle, and the fuel tank placed in
132-430: A Tricycle landing gear . The PA-11 was one of the first aircraft to be used by Piper for experiments with the nose wheel (also known as tricycle gear ) configuration. Although its original design is intended to be a tail-dragger, a modification was created to mount a nose wheel. The nose wheel is attached to the two rear engine mounts by y-shaped steel tubes attached to a steel tube with a shaft that slides freely with
198-501: A ski-jump on take-off is subjected to loads of 0.5g which also last for much longer than a landing impact. Helicopters may have a deck-lock harpoon to anchor them to the deck. Some aircraft have a requirement to use the landing-gear as a speed brake. Flexible mounting of the stowed main landing-gear bogies on the Tupolev Tu-22 R raised the aircraft flutter speed to 550 kn (1,020 km/h). The bogies oscillated within
264-414: A "boat" hull/floats and retractable wheels, which allow it to operate from land or water. Beaching gear is detachable wheeled landing gear that allows a non-amphibious floatplane or flying boat to be maneuvered on land. It is used for aircraft maintenance and storage and is either carried in the aircraft or kept at a slipway. Beaching gear may consist of individual detachable wheels or a cradle that supports
330-442: A 10 in (25 cm) thick flexible asphalt pavement . The 210,000 lb (95 t) Boeing 727 -200 with four tires on two legs main landing gears required a 20 in (51 cm) thick pavement. The thickness rose to 25 in (64 cm) for a McDonnell Douglas DC-10 -10 with 443,000 lb (201 t) supported on eight wheels on two legs. The heavier, 558,000 lb (253 t), DC-10-30/40 were able to operate from
396-474: A 90° angle during the rearwards-retraction sequence to allow the main wheel to rest "flat" above the lower end of the main gear strut, or flush within the wing or engine nacelles, when fully retracted. Examples are the Curtiss P-40 , Vought F4U Corsair , Grumman F6F Hellcat , Messerschmitt Me 210 and Junkers Ju 88 . The Aero Commander family of twin-engined business aircraft also shares this feature on
462-415: A conventional geared aircraft can be accomplished in two ways. Normal landings are done by touching all three wheels down at the same time in a three-point landing . This method does allow the shortest landing distance but can be difficult to carry out in crosswinds, as rudder control may be reduced severely before the tailwheel can become effective. The alternative is the wheel landing . This requires
528-476: A forward and aft position. The forward position was used for take-off to give a longer lever-arm for pitch control and greater nose-up attitude. The aft position was used to reduce landing bounce and reduce risk of tip-back during ground handling. The tandem or bicycle layout is used on the Hawker Siddeley Harrier, which has two main-wheels behind a single nose-wheel under the fuselage and
594-585: A higher sink-rate requirement because the aircraft are flown onto the deck with no landing flare . Other features are related to catapult take-off requirements for specific aircraft. For example, the Blackburn Buccaneer was pulled down onto its tail-skid to set the required nose-up attitude. The naval McDonnell Douglas F-4 Phantom II in UK service needed an extending nosewheel leg to set the wing attitude at launch. The landing gear for an aircraft using
660-474: A higher sink-rate requirement if a carrier-type, no-flare landing technique has to be adopted to reduce touchdown scatter. For example, the Saab 37 Viggen , with landing gear designed for a 5m/sec impact, could use a carrier-type landing and HUD to reduce its scatter from 300 m to 100m. The de Havilland Canada DHC-4 Caribou used long-stroke legs to land from a steep approach with no float. A flying boat has
726-489: A light aircraft, an emergency extension system is always available. This may be a manually operated crank or pump, or a mechanical free-fall mechanism which disengages the uplocks and allows the landing gear to fall under gravity. Aircraft landing gear includes wheels equipped with solid shock absorbers on light planes, and air/oil oleo struts on larger aircraft. As aircraft weights have increased more wheels have been added and runway thickness has increased to keep within
SECTION 10
#1732776357577792-403: A lower fuselage with the shape of a boat hull giving it buoyancy. Wing-mounted floats or stubby wing-like sponsons are added for stability. Sponsons are attached to the lower sides of the fuselage. A floatplane has two or three streamlined floats. Amphibious floats have retractable wheels for land operation. An amphibious aircraft or amphibian usually has two distinct landing gears, namely
858-537: A nosewheel) chassis. Landing is done on skids or similar simple devices (fixed or retractable). The SNCASE Baroudeur used this arrangement. Historical examples include the "dolly"-using Messerschmitt Me 163 Komet rocket fighter, the Messerschmitt Me 321 Gigant troop glider, and the first eight "trolley"-using prototypes of the Arado Ar 234 jet reconnaissance bomber. The main disadvantage to using
924-457: A similar arrangement, except that the fore and aft gears each have two twin-wheel units side by side. Quadricycle gear is similar to bicycle but with two sets of wheels displaced laterally in the fore and aft positions. Raymer classifies the B-52 gear as quadricycle. The experimental Fairchild XC-120 Packplane had quadricycle gear located in the engine nacelles to allow unrestricted access beneath
990-478: A single wheel, retractable or fixed, centered under the fuselage, which is referred to as monowheel gear or monowheel landing gear . Monowheel gear is also used on some powered aircraft, where drag reduction is a priority, such as the Europa XS . Monowheel power aircraft use retractable wingtip legs (with small castor wheels attached) to prevent the wingtips from striking the ground. A monowheel aircraft may have
1056-520: A smaller wheel near the tip of each wing. On second generation Harriers, the wing is extended past the outrigger wheels to allow greater wing-mounted munition loads to be carried, or to permit wing-tip extensions to be bolted on for ferry flights. A tandem layout was evaluated by Martin using a specially-modified Martin B-26 Marauder (the XB-26H) to evaluate its use on Martin's first jet bomber,
1122-650: A tailwheel (like the Europa) or a nosewheel (like the Schleicher ASK 23 glider). Taildragger aircraft require more training time for student pilots to master. This was a large factor in the 1950s switch by most manufacturers to nosewheel-equipped trainers, and for many years nosewheel aircraft have been more popular than taildraggers. As a result, most Private Pilot Licence (PPL) pilots now learn to fly in tricycle gear aircraft (e.g. Cessna 172 or Piper Cherokee ) and only later transition to taildraggers. Landing
1188-557: A tricycle undercarriage to prevent damage to the underside of the fuselage if over-rotation occurs on take-off leading to a tail strike . Aircraft with tail-strike protection include the B-29 Superfortress , Boeing 727 trijet and Concorde . Some aircraft with retractable conventional landing gear have a fixed tailwheel. Hoerner estimated the drag of the Bf 109 fixed tailwheel and compared it with that of other protrusions such as
1254-412: Is also unique in that all four pairs of main wheels can be steered. This allows the landing gear to line up with the runway and thus makes crosswind landings easier (using a technique called crab landing ). Since tandem aircraft cannot rotate for takeoff, the forward gear must be long enough to give the wings the correct angle of attack during takeoff. During landing, the forward gear must not touch
1320-622: Is also used on some tricycle gear aircraft, with the nosewheel being the freely castering wheel instead. Like the steerable tailwheel/skid, it is usually integrated with the rudder pedals on the craft to allow an easy transition between wheeled and aerodynamic control. The tailwheel configuration offers several advantages over the tricycle landing gear arrangement, which make tailwheel aircraft less expensive to manufacture and maintain. The conventional landing gear arrangement has disadvantages compared to nosewheel aircraft. Jet aircraft generally cannot use conventional landing gear, as this orients
1386-403: Is an aircraft undercarriage consisting of two main wheels forward of the center of gravity and a small wheel or skid to support the tail. The term taildragger is also used. The term "conventional" persists for historical reasons, but all modern jet aircraft and most modern propeller aircraft use tricycle gear . In early aircraft, a tailskid made of metal or wood was used to support
SECTION 20
#17327763575771452-465: Is required to reduce the impact with the surface of the water. A vee bottom parts the water and chines deflect the spray to prevent it damaging vulnerable parts of the aircraft. Additional spray control may be needed using spray strips or inverted gutters. A step is added to the hull, just behind the center of gravity, to stop water clinging to the afterbody so the aircraft can accelerate to flying speed. The step allows air, known as ventilation air, to break
1518-527: Is the undercarriage of an aircraft or spacecraft that is used for taxiing , takeoff or landing . For aircraft, it is generally needed for all three of these. It was also formerly called alighting gear by some manufacturers, such as the Glenn L. Martin Company . For aircraft, Stinton makes the terminology distinction undercarriage (British) = landing gear (US) . For aircraft, the landing gear supports
1584-705: The Beriev A-40 Hydro flaps were used on the Martin Marlin and Martin SeaMaster . Hydroflaps, submerged at the rear of the afterbody, act as a speed brake or differentially as a rudder. A fixed fin, known as a skeg , has been used for directional stability. A skeg, was added to the second step on the Kawanishi H8K flying boat hull. High speed impacts in rough water between the hull and wave flanks may be reduced using hydro-skis which hold
1650-517: The Camel fighter) were equipped with steerable tailskids, which operate similar to a tailwheel. When the pilot pressed the right rudder pedal — or the right footrest of a "rudder bar" in World War I — the skid pivoted to the right, creating more drag on that side of the plane and causing it to turn to the right. While less effective than a steerable wheel, it gave the pilot some control of the direction
1716-561: The Martin Marlin , the Martin M-270, was tested with a new hull with a greater length/beam ratio of 15 obtained by adding 6 feet to both the nose and tail. Rough-sea capability can be improved with lower take-off and landing speeds because impacts with waves are reduced. The Shin Meiwa US-1A is a STOL amphibian with blown flaps and all control surfaces. The ability to land and take-off at relatively low speeds of about 45 knots and
1782-702: The Martin XB-48 . This configuration proved so manoeuvrable that it was also selected for the B-47 Stratojet . It was also used on the U-2, Myasishchev M-4 , Yakovlev Yak-25 , Yak-28 and Sud Aviation Vautour . A variation of the multi tandem layout is also used on the B-52 Stratofortress which has four main wheel bogies (two forward and two aft) underneath the fuselage and a small outrigger wheel supporting each wing-tip. The B-52's landing gear
1848-470: The maximum takeoff weight (MTOW) and 1.5 to 1.75% of the aircraft cost, but 20% of the airframe direct maintenance cost. A suitably-designed wheel can support 30 t (66,000 lb), tolerate a ground speed of 300 km/h and roll a distance of 500,000 km (310,000 mi) ; it has a 20,000 hours time between overhaul and a 60,000 hours or 20 year life time. Wheeled undercarriages normally come in two types: The taildragger arrangement
1914-666: The British Supermarine Attacker naval fighter and the Soviet Yakovlev Yak-15 . Both first flew in 1946 and owed their configurations to being developments of earlier propeller powered aircraft. The Attacker's tailwheel configuration was a result of it using the Supermarine Spiteful 's wing, avoiding expensive design modification or retooling. The engine exhaust was behind the elevator and tailwheel, reducing problems. The Yak-15
1980-416: The aircraft can be landed in a satisfactory manner in a range of failure scenarios. The Boeing 747 was given four separate and independent hydraulic systems (when previous airliners had two) and four main landing gear posts (when previous airliners had two). Safe landing would be possible if two main gear legs were torn off provided they were on opposite sides of the fuselage. In the case of power failure in
2046-565: The aircraft to balance properly with the nose wheel, the main gear was flipped around so that the center of balance would move forward. The pilot would sit in the front seat for added stability. A number of Cub Specials have been converted for flight operation using floats. Data from Piper Aircraft and Their Forerunners General characteristics Performance [REDACTED] Media related to Piper PA-11 Cub Special at Wikimedia Commons Conventional landing gear Conventional landing gear , or tailwheel-type landing gear ,
Piper PA-11 Cub Special - Misplaced Pages Continue
2112-470: The airstream, it is called a semi-retractable gear. Most retractable gear is hydraulically operated, though some is electrically operated or even manually operated on very light aircraft. The landing gear is stowed in a compartment called a wheel well. Pilots confirming that their landing gear is down and locked refer to "three greens" or "three in the green.", a reference to the electrical indicator lights (or painted panels of mechanical indicator units) from
2178-434: The craft was moving while taxiing or beginning the takeoff run, before there was enough airflow over the rudder for it to become effective. Another form of control, which is less common now than it once was, is to steer using " differential braking ", in which the tailwheel is a simple, freely castering mechanism, and the aircraft is steered by applying brakes to one of the mainwheels in order to turn in that direction. This
2244-422: The craft when it is not flying, allowing it to take off, land, and taxi without damage. Wheeled landing gear is the most common, with skis or floats needed to operate from snow/ice/water and skids for vertical operation on land. Retractable undercarriages fold away during flight, which reduces drag , allowing for faster airspeeds . Landing gear must be strong enough to support the aircraft and its design affects
2310-520: The engines at a high angle, causing their jet blast to bounce off the ground and back into the air, preventing the elevators from functioning properly. This problem occurred with the third, or "V3" prototype of the German Messerschmitt Me 262 jet fighter. After the first four prototype Me 262 V-series airframes were built with retracting tailwheel gear, the fifth prototype was fitted with fixed tricycle landing gear for trials, with
2376-410: The entire aircraft. In the former case, the beaching gear is manually attached or detached with the aircraft in the water; in the latter case, the aircraft is maneuvered onto the cradle. Helicopters are able to land on water using floats or a hull and floats. For take-off a step and planing bottom are required to lift from the floating position to planing on the surface. For landing a cleaving action
2442-418: The fuselage for attaching a large freight container. Helicopters use skids, pontoons or wheels depending on their size and role. To decrease drag in flight, undercarriages retract into the wings and/or fuselage with wheels flush with the surrounding surface, or concealed behind flush-mounted doors; this is called retractable gear. If the wheels do not retract completely but protrude partially exposed to
2508-424: The fuselage lower sides as retractable main gear units on modern designs—were first seen during World War II, on the experimental German Arado Ar 232 cargo aircraft, which used a row of eleven "twinned" fixed wheel sets directly under the fuselage centerline to handle heavier loads while on the ground. Many of today's large cargo aircraft use this arrangement for their retractable main gear setups, usually mounted on
2574-438: The fuselage. The 640 t (1,410,000 lb) Antonov An-225 , the largest cargo aircraft, had 4 wheels on the twin-strut nose gear units like the smaller Antonov An-124 , and 28 main gear wheels. The 97 t (214,000 lb) A321neo has a twin-wheel main gear inflated to 15.7 bar (228 psi), while the 280 t (620,000 lb) A350 -900 has a four-wheel main gear inflated to 17.1 bar (248 psi). STOL aircraft have
2640-603: The hull out of the water at higher speeds. Hydro skis replace the need for a boat hull and only require a plain fuselage which planes at the rear. Alternatively skis with wheels can be used for land-based aircraft which start and end their flight from a beach or floating barge. Hydro-skis with wheels were demonstrated as an all-purpose landing gear conversion of the Fairchild C-123 , known as the Panto-base Stroukoff YC-134 . A seaplane designed from
2706-471: The hydrodynamic features of the hull, long length/beam ratio and inverted spray gutter for example, allow operation in wave heights of 15 feet. The inverted gutters channel spray to the rear of the propeller discs. Low speed maneuvring is necessary between slipways and buoys and take-off and landing areas. Water rudders are used on seaplanes ranging in size from the Republic RC-3 Seabee to
Piper PA-11 Cub Special - Misplaced Pages Continue
2772-402: The landing gear usually consists of skis or a combination of wheels and skis. Some aircraft use wheels for takeoff and jettison them when airborne for improved streamlining without the complexity, weight and space requirements of a retraction mechanism. The wheels are sometimes mounted onto axles that are part of a separate "dolly" (for main wheels only) or "trolley" (for a three-wheel set with
2838-405: The landing gear usually only supports the vehicle on landing and during subsequent surface movement, and is not used for takeoff. Given their varied designs and applications, there exist dozens of specialized landing gear manufacturers. The three largest are Safran Landing Systems , Collins Aerospace (part of Raytheon Technologies ) and Héroux-Devtek . The landing gear represents 2.5 to 5% of
2904-417: The lower corners of the central fuselage structure. The prototype Convair XB-36 had most of its weight on two main wheels, which needed runways at least 22 in (56 cm) thick. Production aircraft used two four-wheel bogies, allowing the aircraft to use any airfield suitable for a B-29. A relatively light Lockheed JetStar business jet, with four wheels supporting 44,000 lb (20 t), needed
2970-504: The main gear struts lengthened as they were extended to give sufficient ground clearance for their large four-bladed propellers. One exception to the need for this complexity in many WW II fighter aircraft was Japan's famous Zero fighter, whose main gear stayed at a perpendicular angle to the centerline of the aircraft when extended, as seen from the side. The main wheels on the Vought F7U Cutlass could move 20 inches between
3036-489: The main gears, which retract aft into the ends of the engine nacelles . The rearward-retracting nosewheel strut on the Heinkel He 219 and the forward-retracting nose gear strut on the later Cessna Skymaster similarly rotated 90 degrees as they retracted. On most World War II single-engined fighter aircraft (and even one German heavy bomber design ) with sideways retracting main gear, the main gear that retracted into
3102-611: The nacelle under the control of dampers and springs as an anti-flutter device. Some experimental aircraft have used gear from existing aircraft to reduce program costs. The Martin-Marietta X-24 lifting body used the nose/main gear from the North American T-39 / Northrop T-38 and the Grumman X-29 from the Northrop F-5 / General Dynamics F-16 . When an airplane needs to land on surfaces covered by snow,
3168-444: The nosewheel/tailwheel and the two main gears. Blinking green lights or red lights indicate the gear is in transit and neither up and locked or down and locked. When the gear is fully stowed up with the up-locks secure, the lights often extinguish to follow the dark cockpit philosophy; some airplanes have gear up indicator lights. Redundant systems are used to operate the landing gear and redundant main gear legs may also be provided so
3234-722: The outset with hydro-skis was the Convair F2Y Sea Dart prototype fighter. The skis incorporated small wheels, with a third wheel on the fuselage, for ground handling. In the 1950s hydro-skis were envisaged as a ditching aid for large piston-engined aircraft. Water-tank tests done using models of the Lockheed Constellation , Douglas DC-4 and Lockheed Neptune concluded that chances of survival and rescue would be greatly enhanced by preventing critical damage associated with ditching. The landing gear on fixed-wing aircraft that land on aircraft carriers have
3300-610: The pilot to land the aircraft on the mainwheels while maintaining the tailwheel in the air with elevator to keep the angle of attack low. Once the aircraft has slowed to a speed that can ensure control will not be lost, but above the speed at which rudder effectiveness is lost, then the tailwheel is lowered to the ground. Examples of tailwheel aircraft include: Several aftermarket modification companies offer kits to convert many popular nose-wheel equipped aircraft to conventional landing gear. Aircraft for which kits are available include: Differential braking Landing gear
3366-556: The pilot's canopy. A third arrangement (known as tandem or bicycle) has the main and nose gear located fore and aft of the center of gravity (CG) under the fuselage with outriggers on the wings. This is used when there is no convenient location on either side of the fuselage to attach the main undercarriage or to store it when retracted. Examples include the Lockheed U-2 spy plane and the Harrier jump jet . The Boeing B-52 uses
SECTION 50
#17327763575773432-582: The port wing root . Both seats were slightly moved back, and solo flying was usually from the front seat. The prototype and two subsequent pre-production models were built using a modified J-3 fuselage and wings. The prototype first flew in August 1946 followed by the two pre-production aircraft later in 1946. The first production aircraft was completed at Lock Haven in March 1947 and production continued at Lock Haven until September 1949. A second production line
3498-513: The runway loading limit . The Zeppelin-Staaken R.VI , a large German World War I long-range bomber of 1916, used eighteen wheels for its undercarriage, split between two wheels on its nose gear struts, and sixteen wheels on its main gear units—split into four side-by-side quartets each, two quartets of wheels per side—under each tandem engine nacelle, to support its loaded weight of almost 12 t (26,000 lb). Multiple "tandem wheels" on an aircraft—particularly for cargo aircraft , mounted to
3564-538: The same thickness pavements with a third main leg for ten wheels, like the first Boeing 747 -100, weighing 700,000 lb (320 t) on four legs and 16 wheels. The similar-weight Lockheed C-5 , with 24 wheels, needs an 18 in (46 cm) pavement. The twin-wheel unit on the fuselage centerline of the McDonnell Douglas DC-10 -30/40 was retained on the MD-11 airliner and the same configuration
3630-558: The sixth prototype onwards getting fully retracting tricycle gear. A number of other experimental and prototype jet aircraft had conventional landing gear, including the first successful jet, the Heinkel He 178 , the Ball-Bartoe Jetwing research aircraft, and a single Vickers VC.1 Viking , which was modified with Rolls-Royce Nene engines to become the world's first jet airliner. Rare examples of jet-powered tailwheel aircraft that went into production and saw service include
3696-443: The tail on the ground. In most modern aircraft with conventional landing gear, a small articulated wheel assembly is attached to the rearmost part of the airframe in place of the skid. This wheel may be steered by the pilot through a connection to the rudder pedals, allowing the rudder and tailwheel to move together. Before aircraft commonly used tailwheels, many aircraft (like a number of First World War Sopwith aircraft, such as
3762-508: The takeoff dolly/trolley and landing skid(s) system on German World War II aircraft—intended for a sizable number of late-war German jet and rocket-powered military aircraft designs—was that aircraft would likely be scattered all over a military airfield after they had landed from a mission, and would be unable to taxi on their own to an appropriately hidden "dispersal" location, which could easily leave them vulnerable to being shot up by attacking Allied fighters. A related contemporary example are
3828-685: The water suction on the afterbody. Two steps were used on the Kawanishi H8K . A step increases the drag in flight. The drag contribution from the step can be reduced with a fairing. A faired step was introduced on the Short Sunderland III. One goal of seaplane designers was the development of an open ocean seaplane capable of routine operation from very rough water. This led to changes in seaplane hull configuration. High length/beam ratio hulls and extended afterbodies improved rough water capabilities. A hull much longer than its width also reduced drag in flight. An experimental development of
3894-482: The weight, balance and performance. It often comprises three wheels, or wheel-sets, giving a tripod effect. Some unusual landing gear have been evaluated experimentally. These include: no landing gear (to save weight), made possible by operating from a catapult cradle and flexible landing deck: air cushion (to enable operation over a wide range of ground obstacles and water/snow/ice); tracked (to reduce runway loading). For launch vehicles and spacecraft landers ,
3960-415: The wheel. Cables run underneath the belly directly from fixtures on the rudder pedals to the nose wheel shaft. This gave the ability to steer by pivoting the nose wheel shaft with the rudder pedals. The shock system consisted of six circular bungee cords, sometimes four for softer landings, located on either side of the nose wheel shaft to ears on the top tube and the bottom shaft connected to the wheel. For
4026-499: The wings was raked forward in the "down" position for better ground handling, with a retracted position that placed the main wheels at some distance aft of their position when downairframe—this led to a complex angular geometry for setting up the "pintle" angles at the top ends of the struts for the retraction mechanism's axis of rotation. with some aircraft, like the P-47 Thunderbolt and Grumman Bearcat , even mandating that
SECTION 60
#17327763575774092-424: The wingtip support wheels ("pogos") on the Lockheed U-2 reconnaissance aircraft, which fall away after take-off and drop to earth; the aircraft then relies on titanium skids on the wingtips for landing. Some main landing gear struts on World War II aircraft, in order to allow a single-leg main gear to more efficiently store the wheel within either the wing or an engine nacelle, rotated the single gear strut through
4158-530: Was based on the Yakovlev Yak-3 propeller fighter. Its engine was mounted under the forward fuselage. Despite its unusual configuration, the Yak-15 was easy to fly. Although a fighter, it was mainly used as a trainer aircraft to prepare Soviet pilots for flying more advanced jet fighters. A variation of the taildragger layout is the monowheel landing gear . To minimize drag, many modern gliders have
4224-445: Was common during the early propeller era, as it allows more room for propeller clearance. Most modern aircraft have tricycle undercarriages. Taildraggers are considered harder to land and take off (because the arrangement is usually unstable , that is, a small deviation from straight-line travel will tend to increase rather than correct itself), and usually require special pilot training. A small tail wheel or skid/bumper may be added to
4290-544: Was established at Ponca City between September 1947 and January 1948. On the early PA-11s, the fuselage was painted with a metallic blue on the lower half the rest being Lock Haven Yellow. The later PA-11s were all yellow with a simple brown stripe. The PA-11 also formed the basis for the next evolution in the Cub series, the PA-18 Super Cub, which shares many features. A small number of PA-11s have been modified to use
4356-467: Was used on the initial 275 t (606,000 lb) Airbus A340 -200/300, which evolved in a complete four-wheel undercarriage bogie for the heavier 380 t (840,000 lb) Airbus A340-500/-600. The up to 775,000 lb (352 t) Boeing 777 has twelve main wheels on two three-axles bogies, like the later Airbus A350 . The 575 t (1,268,000 lb) Airbus A380 has a four-wheel bogie under each wing with two sets of six-wheel bogies under
#576423