Misplaced Pages

#696303

46-490: Three engines have been produced: a 1.8 L, a 2.0 L, and a 2.4 L. The initial design of the engine block and cylinder head was handled by Hyundai as part of the Global Engine Alliance. The engines feature an aluminum engine block with siamesed cast iron cylinder liners (which do not allow coolant to flow between adjacent liners). By using cylinder liners, the engine's bore can be altered, therefore

92-461: A bore and stroke of 88 mm × 82 mm (3.46 in × 3.23 in) and a 10.2:1 compression ratio . Applications: The 2.4 L Tigershark SOHC inline 4-cylinder gasoline engine uses MultiAir 2 variable valve timing and variable valve lift technology and produces 184 hp (137 kW) and 174 lb⋅ft (236 N⋅m) of torque. Only Multi-Air heads feature electro-hydraulic variable valve timing and lift, although only on

138-510: A monobloc . The main structure of an engine typically consists of the cylinders , coolant passages, oil galleries, crankcase, and cylinder head(s) . The first production engines of the 1880s to 1920s usually used separate components for each element, which were bolted together during engine assembly. Modern engines, however, often combine many elements into a single component to reduce production costs. The evolution from separate components to monobloc engine blocks has gradually progressed since

184-499: A bore of 3.38 in (86 mm) and a stroke of 3.05 in (77 mm). The compression ratio is 10.5:1. The 1.8L DOHC inline 4-cylinder engine served as the standard engine in the Dodge Caliber SE and SXT trim for the 2007–2009 model years. Applications: The 2.0L DOHC inline four-cylinder gasoline engine is capable of 158 hp (118 kW) and produces 141 lb⋅ft (191 N⋅m) of torque. The engine has

230-456: A construction where the cylinders (or at least their liners) were cast as individuals, and the outer water jacket was applied later from copper or steel sheet. This complex construction was expensive, but lightweight, and so it was only widely used for aircraft. V engines remained with a separate block casting for each bank . The complex ducting required for inlet manifolds between the banks were too complicated to cast otherwise. For economy,

276-498: A displacement of 2.0 L; 121.9 cu in (1,998 cc) with a bore and a stroke of 3.38 in × 3.38 in (86 mm × 86 mm). The compression ratio of the engine is 10.5:1. The 2.0 L engine was offered by Dodge in the Dodge Caliber . Outside North America, the 2.0 was the base engine for the 2007 Chrysler Sebring and 2008 Dodge Avenger. Applications: The 2.4 L, 172 hp (128 kW) engine

322-524: A few engines, such as the V12 Pierce-Arrow , were designed to use identical castings for each bank, left and right. Some rare engines, such as the Lancia 22½° narrow-angle V12 of 1919, did use a single block casting for both banks. A 322 cu in (5.3 L) monobloc engine was used in 1936's Series 60 . It was designed to be the company's next-generation powerplant at reduced cost from

368-716: A monobloc cylinder head were and continue to be a severe drawback. As head gaskets became able to handle greater heat and pressure, the technique went out of use. It is almost unknown today, but has found a few niche uses, as the technique of monobloc cylinder heads was adopted by the Japanese model engine manufacturer Saito Seisakusho for their glow fueled and spark ignition model four-stroke engines for RC aircraft propulsion needs. Monobloc cylinders also continue to be used on small 2 stroke-cycle engines for power equipment used to maintain lawns and gardens, such as string trimmers, tillers and leaf blowers. Casting technology at

414-652: A monobloc design where the cylinder head, block, and half of the crankcase share the same casting. Apart from cost, one reason for this is to produce an overall lower engine height. The primary disadvantage can be that repairs become more time-consuming and impractical. An example of engines with integrated cylinder heads are the Honda GC -series and GXV-series engines, which are sometimes called "Uniblock" by Honda. Several cars with transverse engines have used an engine block consisting of an integrated transmission and crankcase. Cars that have used this arrangement include

460-631: A monobloc design with one block for all cylinders plus an integrated crankcase. In such cases, the skirts of the cylinder banks form a crankcase area of sorts, which is still often called a crankcase despite no longer being a discrete part. Using steel cylinder liners and bearing shells minimizes the effect of the relative softness of aluminium. Some engine designs use plasma transferred wire arc thermal spraying , instead of cylinder sleeves, to further reduce weight. These types of engines can also be made of compacted graphite iron , such as in some diesel engines. Some modern consumer-grade small engines use

506-405: A monobloc, it also became possible to cast both cylinders and crankcase as one unit. The main reason for this was to improve stiffness of the engine construction, reducing vibration and permitting higher speeds. Most engines, except some V engines, are now a monobloc of crankcase and cylinder block. Light-duty consumer-grade Honda GC -family small engines use a headless monobloc design where

SECTION 10

#1732797934697

552-489: A removable sleeve. A combination of materials are used in their construction, such as steel for the cylinder barrels and aluminum alloys for the cylinder heads to save weight. Common rebuilding techniques include chrome plating the inside of the cylinder barrels in a "cracked" finish that mimics the " cross-hatched " finish normally created by typical cylinder honing. Older engines operated on unleaded automotive gasoline as allowed by supplemental type certificates approved by

598-412: A separate crankcase. As casting techniques improved, an entire cylinder block of 4, 6, or 8 cylinders could be produced in one piece. This monobloc construction was more straightforward and more cost-effective to produce. All the cylinders and crankcase could be made in a single component for straight engine cylinder layouts. One of the early engines produced using this method is the 4-cylinder engine in

644-475: A single unit. An early example is the Fordson tractor. Monobloc engine A monobloc or en bloc engine is an internal-combustion piston engine some of whose major components (such as cylinder head , cylinder block , or crankcase ) are formed, usually by casting , as a single integral unit, rather than being assembled later. This has the advantages of improving mechanical stiffness, and improving

690-410: Is less restricted than on an inline engine with a monobloc crankcase and cylinders, as most modern engines are. As they have high specific power and require great reliability, the advantages of the monobloc remained attractive. General aviation engines such as Franklin , Continental , and Lycoming are still manufactured new and continue to use monobloc individual cylinders, although Franklin uses

736-421: Is the name for the next generation of World Gasoline Engines, with work starting on them shortly after Fiat's acquisition of Chrysler. The major differences compared to the first generation are the updated valvetrain and intakes. The 2.0 L Tigershark DOHC inline 4-cylinder gasoline engine has dual-variable valve timing and produces 160 hp (119 kW) and 148 lb⋅ft (201 N⋅m) of torque. It utilizes

782-466: The FAA may require more frequent machining replacement of valves and seats. Special tools are used to maintain valve seats in these cylinders. Non-destructive testing should be performed to look for flaws that may have arisen during extreme use, engine damage from sudden propeller stoppage or extended engine operation at every overhaul or rebuild. Historically the difficulties of machining, and maintaining

828-467: The Ford Model T , introduced in 1908. The technique spread to straight-six engines and was commonly used by the mid-1920s. Up until the 1930s, most V engines retained a separate block casting for each cylinder bank, with both bolted onto a common crankcase (itself a separate casting). For economy, some engines were designed to use identical castings for each bank, left and right. A rare exception

874-429: The crankshaft . As with cylinder blocks, this is primarily an integrated component in modern engines. Engine blocks are typically cast from either cast iron or an aluminium alloy . Aluminium blocks are much lighter and transfer heat more effectively to coolant, but iron blocks retain some advantages, such as durability and reduced thermal expansion . Weight reductions through material selection . Presently, most of

920-543: The 1930s. Aircraft engines at this time were beginning to use high supercharging pressures, increasing the stress on their head gaskets. Engines such as the Rolls-Royce Buzzard used monobloc heads for reliability. The last engines to make widespread use of monobloc cylinder heads were large air-cooled aircraft radial engines , such as the Wasp Major . These have individual cylinder barrels, so access

966-539: The 1966-1973 Lamborghini Miura and cars using the BMC A-series and E-series engines. This design often results in the engine and transmission sharing the same oil. Motorcycles such as the Honda CB750 use a similar layout, with the cylinder block and crankcase integrated with part of the transmission. Many farm tractor designs integrate the cylinder block, crankcase, transmission, and rear axle into

SECTION 20

#1732797934697

1012-445: The 353 and Cadillac V16 . The monobloc's cylinders and crankcase were cast as a single unit, and it used hydraulic valve lifters for durability. This design allowed the creation of the mid-priced Series 60 line. Modern cylinders, except for air-cooled engines and some V engines , are now universally cast as a single cylinder block, and modern heads are nearly always separate components. As casting improved and cylinder blocks became

1058-400: The backbone of the cylinder wall. Additional sleeves are inserted within, which remain "dry" outside, surrounded by the block's material. For either wet or dry liner designs, the liners (or sleeves) can be replaced, potentially allowing an engine overhaul or rebuild without replacing the block itself. However, there are more practical repair options. The crankcase is the structure that houses

1104-399: The crankshaft from beneath. One solution to this for side-valve engines was to place a screwed plug directly above each valve, and to access the valves through this (illustrated). The tapered threads of the screwed plug provided a reliable seal. For low-powered engines this was a popular solution for some years, but it was difficult to cool this plug, as the water jacket didn't extend into

1150-477: The cylinder block, to which a separate crankcase was attached. Modern engine blocks typically have the crankcase integrated with the cylinder block as a single component. Engine blocks often also include elements such as coolant passages and oil galleries. The term "cylinder block" is often used interchangeably with "engine block". However, technically, the block of a modern engine (i.e., multiple cylinders integrated with another component) would be classified as

1196-413: The cylinder head, block, and half the crankcase share the same casting, termed 'uniblock' by Honda. One reason for this, apart from cost, is to produce an overall lower engine height. Being an air-cooled OHC design, this is possible thanks to current aluminum casting techniques and lack of complex hollow spaces for liquid cooling. The valves are vertical, so as to permit assembly in this confined space. On

1242-473: The dawn of the internal combustion engine could reliably cast either large castings, or castings with complex internal cores to allow for water jackets, but not both simultaneously. Most early engines, particularly those with more than four cylinders, had their cylinders cast as pairs or triplets of cylinders, then bolted to a single crankcase. As casting techniques improved, the entire cylinder block of four, six or even eight cylinders could be cast as one. This

1288-434: The displacement as well, just by adding a different set of cylinder liners. The engine also features an aluminum cylinder head with double overhead camshafts and variable valve timing . The 1.8L is a dual overhead cam (DOHC) inline 4-cylinder gasoline engine capable of 148 hp (110 kW) and 125 lb⋅ft (169 N⋅m) of torque. The engine has displacement of 1.8 L; 109.7 cu in (1,798 cc) with

1334-461: The earliest decades of internal combustion engine development, cylinders were usually cast individually, so cylinder blocks were usually produced separately for each cylinder. Following that, engines began to combine two or three cylinders into a single-cylinder block, with an engine combining several of these cylinder blocks. In early engines with multiple cylinder banks – such as V6 , V8 , or flat-6 engines – each bank

1380-442: The early 20th century. The integration of elements has relied on the development of foundry and machining techniques. For example, a practical, low-cost V8 engine was not feasible until Ford developed the methods used to build its flathead V8 engine . Other manufacturers then applied those techniques to their engines. A cylinder block is a structure that contains the cylinder , plus any cylinder sleeves and coolant passages. In

1426-676: The engine block, taking into account the particular needs of the material. An engine where all the cylinders share a common block is called a monobloc engine . Most modern engines use a monobloc design, and few have a separate block for each cylinder. This has led to the term "engine block," which usually implies a monobloc design, with "monobloc" rarely used. In the early years of the internal combustion engine, casting technology couldn't produce large castings with complex internal cores (for water jackets etc). Most early engines, particularly those with more than four cylinders, had their cylinders cast as pairs or triplets of cylinders, then bolted to

World Gasoline Engine - Misplaced Pages Continue

1472-438: The engine blocks in mass production are gray castings. Reducing weight has resulted in using aluminum-silicon alloys more frequently for the engine block in small-displacement engines. Engine blocks of comparable design, but using Al-Si alloys, are not lighter than cast iron engine blocks in the same ratio as that for the specific weights of the materials. In engine blocks made of gray cast iron, weight can be reduced by optimizing

1518-416: The engine's coolant. In other words, the liner is the entire cylinder wall, rather than merely a sleeve. The advantages of wet liners are a lower mass, reduced space requirements, and coolant being heated faster from a cold start, reducing start-up fuel consumption and heating the car cabin sooner. Dry liner cylinder blocks use either the block's material or a discrete liner inserted into the block to form

1564-417: The intake side. The system is based on FIAT technology. It utilizes a bore and stroke of 88 mm × 97 mm (3.46 in × 3.82 in) and a 10.0:1 compression ratio. Applications: Engine block In an internal combustion engine , the engine block is the structure that contains the cylinders and other components. The engine block in an early automotive engine consisted of just

1610-444: The monobloc head is that access to the inside of the combustion chamber (the upper volume of the cylinder) is difficult. Access through the cylinder bore is restricted for machining the valve seats, or for inserting angled valves. An even more serious restriction is de-coking and re-grinding valve seats, a regular task on older engines. Rather than removing the cylinder head from above, the mechanic must remove pistons, connecting rods and

1656-522: The more common contemporary practice. Where the monobloc technique has later become the norm, the specific term fell from favour. It is now usual practice to use monobloc cylinders and crankcases, but a monobloc head (for a water-cooled inline engine at least) would be regarded as peculiar and obsolescent. The head gasket is the most highly stressed static seal in an engine, and was a source of considerable trouble in early years. The monobloc cylinder head forms both cylinder and head in one unit, thus averting

1702-436: The need for a seal. Along with head gasket failure, one of the least reliable parts of the early petrol engine was the exhaust valve, which tended to fail by overheating. A monobloc head could provide good water cooling, thus reduced valve wear, as it could extend the water jacket uninterrupted around both head and cylinder. Engines with gaskets required a metal-to-metal contact face here, disrupting water flow. The drawback to

1748-402: The other hand, performing basic repairs becomes so time-consuming that the engine can be considered disposable. Commercial-duty Honda GX -family engines (and their many popular knock-offs ) have a more conventional design of a single crankcase and cylinder casting, with a separate cylinder head. Honda produces many other head-block-crankcase monoblocs under a variety of different names, such as

1794-444: The plug. As performance increased, it also became important to have better combustion chamber designs with less "dead space". One solution was to place the spark plug in the centre of this plug, which at least made use of the space. This placed the spark plug further from the combustion chamber, leading to long flame paths and slower ignition. During World War I , development of the internal combustion engine greatly progressed. After

1840-408: The reliability of the sealing between them. Monobloc techniques date back to the beginnings of the internal combustion engine . Use of this term has changed over time, usually to address the most pressing mechanical problem affecting the engines of its day. There have been three distinct uses of the technique: In most cases, any use of the term describes single-unit construction that is opposed to

1886-463: The structure and thin-wall casting. With this casting technique, a wall thickness of as little as about 3 mm is generally possible. In comparison, the walls of cast iron engine blocks are usually from 4.0 to 5.5 mm thick. Using vermicular graphite cast iron (GGV), a casting material with great strength, enables weight reductions by about 30% compared to conventional casting materials such as GG 25. Weight reduction, to this extent, requires engineering for

World Gasoline Engine - Misplaced Pages Continue

1932-494: The war, as civilian car production resumed, the monobloc cylinder head was required less frequently. Only high-performance cars such as the Leyland Eight of 1920 persisted with it. Bentley and Bugatti were other racing marques who notably adhered to them, through the 1920s and into the 1930s, most famously being used in the purpose-built American Offenhauser straight-four racing engines, first designed and built in

1978-401: Was a simpler construction, thus less expensive to manufacture, and the communal water jacket permitted closer spacing between cylinders. This also improved the mechanical stiffness of the engine, against bending and the increasingly important torsional twist, as cylinder numbers and engine lengths increased. In the context of aircraft engines, the non-monobloc precursor to monobloc cylinders was

2024-713: Was the Lancia 22½° narrow-angle V12 of 1919, which used a single block casting combining both banks. The Ford flathead V8  – introduced in 1932 – represented a significant development in the production of affordable V engines. It was the first V8 engine with a single-engine block casting, putting a V8 into an affordable car for the first time. The communal water jacket of monobloc designs permitted closer spacing between cylinders. The monobloc design approach also improved engines' torsional rigidity as cylinder numbers, engine lengths, and power ratings increased. Most engine blocks today, except some unusual V or radial engines and large marine engines, use

2070-405: Was typically made of one or multiple separate cylinder blocks. Since the 1930s, mass production methods have developed to allow both banks of cylinders to be integrated into the same cylinder block. Wet liner cylinder blocks use cylinder walls that are entirely removable and fit into the block using special gaskets. They are called "wet liners" because their outer sides come in direct contact with

2116-559: Was used by Dodge in the R/T trim line of the Caliber. The dual overhead cam (DOHC) inline four-cylinder engine had 2.4 L; 144.0 cu in (2,360 cc) of displacement with a bore and a stroke of 3.46 in × 3.82 in (88 mm × 97 mm). A 285 hp (213 kW) turbocharged variant of this engine was used in the high-performance SRT-4 version of the Caliber. Applications: The Tigershark engine family

#696303