Misplaced Pages

#869130

70-433: Plans had been in the works to build a lighthouse on the site since 1837. The tower is lined with brick and sheathed with cast iron . It stands 41 feet (12 m) tall but the light is 88 feet (27 m) above sea level because of the additional height of the steep rocky islet on which it sits. Unusually, the stanchions of the walkway railing around the lantern room are decorated with 4-inch (100 mm) brass replicas of

140-464: A 10-tonne impeller) to be sand cast, as the chromium reduces cooling rate required to produce carbides through the greater thicknesses of material. Chromium also produces carbides with impressive abrasion resistance. These high-chromium alloys attribute their superior hardness to the presence of chromium carbides. The main form of these carbides are the eutectic or primary M 7 C 3 carbides, where "M" represents iron or chromium and can vary depending on

210-439: A dimensionless nominal size, which approximately corresponded with the internal diameter in inches of the pipe, and four pressure classes, Class A, Class B, Class C and Class D, each with a specified wall thickness and outer diameter. It is noted that the outer diameter is identical between classes with the exception of sizes 12 to 27, where Classes A and B share one diameter and Classes C and D have another, larger diameter. BS 78

280-409: A metal flask and molding sand was rammed into the annular space between the flask and pattern. The pattern was then removed for casting of the pipe using molten grey iron. The second method did not entail a metal pattern, but entailed the forming of the mold centrifugally by lining the heated flask with a measured amount of thermosetting resin and sand. Either way, the casting machine was stopped after

350-423: A pressure pipe for transmission of water, gas and sewage, and as a water drainage pipe during the 17th, 18th, 19th and 20th centuries. In many modern applications, cast iron pipe has been replaced by ductile iron pipe , but this newer product is still often loosely referred to by the older historical name. The oldest cast iron water pipes date from the 17th century and were installed to distribute water throughout

420-563: A rule of mixtures. In any case, they offer hardness at the expense of toughness . Since carbide makes up a large fraction of the material, white cast iron could reasonably be classified as a cermet . White iron is too brittle for use in many structural components, but with good hardness and abrasion resistance and relatively low cost, it finds use in such applications as the wear surfaces ( impeller and volute ) of slurry pumps , shell liners and lifter bars in ball mills and autogenous grinding mills , balls and rings in coal pulverisers . It

490-424: A spongy steel without the stress concentration effects that flakes of graphite would produce. The carbon percentage present is 3-4% and percentage of silicon is 1.8-2.8%.Tiny amounts of 0.02 to 0.1% magnesium , and only 0.02 to 0.04% cerium added to these alloys slow the growth of graphite precipitates by bonding to the edges of the graphite planes. Along with careful control of other elements and timing, this allows

560-437: A superior product. Many public utilities, municipalities, and private industries still have functional cast iron pipe in service to this day. In a bell and spigot joint one end of the pipe stick is flared, termed the bell or socket, to enable the opposite end of the next stick, the spigot end, to be inserted to create a joint. The gaps in these joints were stuffed with oakum or yarn to retain molten-lead, which solidified into

630-566: A waterproof joint. This was a labor-intensive operation, and the quality of the seal was dependent on the skill of the laborer. Mechanical joints were made by bolting a movable follower ring on the spigot close to the corresponding bell, which compressed a gasket in between. Many water pipes today use mechanical joints, since they are easily made and do not require special skills to install. This type of joint also allows some deflection to occur without sacrificing joint integrity, so that minor alignment adjustments can be made during installation, and

700-399: A year after it was opened. The Dee bridge disaster was caused by excessive loading at the centre of the beam by a passing train, and many similar bridges had to be demolished and rebuilt, often in wrought iron . The bridge had been badly designed, being trussed with wrought iron straps, which were wrongly thought to reinforce the structure. The centres of the beams were put into bending, with

770-438: Is added in the ladle or in the furnace, on the order of 0.5–2.5%, to decrease chill, refine graphite, and increase fluidity. Molybdenum is added on the order of 0.3–1% to increase chill and refine the graphite and pearlite structure; it is often added in conjunction with nickel, copper, and chromium to form high strength irons. Titanium is added as a degasser and deoxidizer, but it also increases fluidity. Vanadium at 0.15–0.5%

SECTION 10

#1732787308870

840-439: Is added to cast iron to stabilize cementite, increase hardness, and increase resistance to wear and heat. Zirconium at 0.1–0.3% helps to form graphite, deoxidize, and increase fluidity. In malleable iron melts, bismuth is added at 0.002–0.01% to increase how much silicon can be added. In white iron, boron is added to aid in the production of malleable iron; it also reduces the coarsening effect of bismuth. Grey cast iron

910-420: Is characterised by its graphitic microstructure, which causes fractures of the material to have a grey appearance. It is the most commonly used cast iron and the most widely used cast material based on weight. Most cast irons have a chemical composition of 2.5–4.0% carbon, 1–3% silicon, and the remainder iron. Grey cast iron has less tensile strength and shock resistance than steel, but its compressive strength

980-485: Is comparable to low- and medium-carbon steel. These mechanical properties are controlled by the size and shape of the graphite flakes present in the microstructure and can be characterised according to the guidelines given by the ASTM . White cast iron displays white fractured surfaces due to the presence of an iron carbide precipitate called cementite. With a lower silicon content (graphitizing agent) and faster cooling rate,

1050-417: Is different than cast iron, because the introduction of magnesium during the casting process causes the graphite to form spheres (graphite nodules) rather than flakes. While this allows the material to remain castable, the end product is much tougher than cast iron, and allows elastic behavior at lower stress levels. Little cast iron pipe is currently manufactured, since ductile iron pipe is widely accepted as

1120-453: Is difficult to cool thick castings fast enough to solidify the melt as white cast iron all the way through. However, rapid cooling can be used to solidify a shell of white cast iron, after which the remainder cools more slowly to form a core of grey cast iron. The resulting casting, called a chilled casting , has the benefits of a hard surface with a somewhat tougher interior. High-chromium white iron alloys allow massive castings (for example,

1190-523: Is notoriously difficult to weld . The earliest cast-iron artefacts date to the 5th century BC, and were discovered by archaeologists in what is now Jiangsu , China. Cast iron was used in ancient China to mass-produce weaponry for warfare, as well as agriculture and architecture. During the 15th century AD, cast iron became utilized for cannons and shot in Burgundy , France, and in England during

1260-433: Is one of the most common alloying elements, because it refines the pearlite and graphite structures, improves toughness, and evens out hardness differences between section thicknesses. Chromium is added in small amounts to reduce free graphite, produce chill, and because it is a powerful carbide stabilizer; nickel is often added in conjunction. A small amount of tin can be added as a substitute for 0.5% chromium. Copper

1330-417: Is the most important alloyant because it forces carbon out of solution. A low percentage of silicon allows carbon to remain in solution, forming iron carbide and producing white cast iron. A high percentage of silicon forces carbon out of solution, forming graphite and producing grey cast iron. Other alloying agents, manganese , chromium , molybdenum , titanium , and vanadium counteract silicon, and promote

1400-698: The Chirk Aqueduct and the Pontcysyllte Aqueduct , both of which remain in use following the recent restorations. The best way of using cast iron for bridge construction was by using arches , so that all the material is in compression. Cast iron, again like masonry, is very strong in compression. Wrought iron, like most other kinds of iron and indeed like most metals in general, is strong in tension, and also tough – resistant to fracturing. The relationship between wrought iron and cast iron, for structural purposes, may be thought of as analogous to

1470-527: The Congo region of the Central African forest, blacksmiths invented sophisticated furnaces capable of high temperatures over 1000 years ago. There are countless examples of welding, soldering, and cast iron created in crucibles and poured into molds. These techniques were employed for the use of composite tools and weapons with cast iron or steel blades and soft, flexible wrought iron interiors. Iron wire

SECTION 20

#1732787308870

1540-605: The Reformation . The amounts of cast iron used for cannons required large-scale production. The first cast-iron bridge was built during the 1770s by Abraham Darby III , and is known as the Iron Bridge in Shropshire , England. Cast iron was also used in the construction of buildings . Cast iron is made from pig iron , which is the product of melting iron ore in a blast furnace . Cast iron can be made directly from

1610-542: The Warring States period . This is based on an analysis of the artifact's microstructures. Because cast iron is comparatively brittle, it is not suitable for purposes where a sharp edge or flexibility is required. It is strong under compression, but not under tension. Cast iron was invented in China in the 5th century BC and poured into molds to make ploughshares and pots as well as weapons and pagodas. Although steel

1680-403: The surface tension to form the graphite into spheroidal particles rather than flakes. Due to their lower aspect ratio , the spheroids are relatively short and far from one another, and have a lower cross section vis-a-vis a propagating crack or phonon . They also have blunt boundaries, as opposed to flakes, which alleviates the stress concentration problems found in grey cast iron. In general,

1750-652: The 13th century and other travellers subsequently noted an iron industry in the Alburz Mountains to the south of the Caspian Sea . This is close to the silk route , thus the use of cast-iron technology being derived from China is conceivable. Upon its introduction to the West in the 15th century it was used for cannon and shot . Henry VIII (reigned 1509–1547) initiated the casting of cannon in England. Soon, English iron workers using blast furnaces developed

1820-533: The 1720s and 1730s by a small number of other coke -fired blast furnaces. Application of the steam engine to power blast bellows (indirectly by pumping water to a waterwheel) in Britain, beginning in 1743 and increasing in the 1750s, was a key factor in increasing the production of cast iron, which surged in the following decades. In addition to overcoming the limitation on water power, the steam-pumped-water powered blast gave higher furnace temperatures which allowed

1890-559: The American Water Works Association. Corrosion of cast-iron-pipe can occur on both the internal and external surfaces. In electro-chemical corrosion, internal anodes develop where bare iron is exposed to aggressive waters, promoting iron to move into solution. The iron combines with various components in the water, forming a tubercle on the pipe interior. This process of tuberculation can eventually cause significant restrictions in cross-sectional area within

1960-482: The Industrial Revolution, cast iron was also widely used for frame and other fixed parts of machinery, including spinning and later weaving machines in textile mills. Cast iron became widely used, and many towns had foundries producing industrial and agricultural machinery. Cast iron pipe Cast iron pipe is pipe made predominantly from gray cast iron . It was historically used as

2030-488: The alloy's composition. The eutectic carbides form as bundles of hollow hexagonal rods and grow perpendicular to the hexagonal basal plane. The hardness of these carbides are within the range of 1500-1800HV. Malleable iron starts as a white iron casting that is then heat treated for a day or two at about 950 °C (1,740 °F) and then cooled over a day or two. As a result, the carbon in iron carbide transforms into graphite and ferrite plus carbon. The slow process allows

2100-429: The benefit of what is called precipitation hardening (as in some steels, where much smaller cementite precipitates might inhibit [plastic deformation] by impeding the movement of dislocations through the pure iron ferrite matrix). Rather, they increase the bulk hardness of the cast iron simply by virtue of their own very high hardness and their substantial volume fraction, such that the bulk hardness can be approximated by

2170-537: The blast furnaces at Coalbrookdale. Other inventions followed, including one patented by Thomas Paine . Cast-iron bridges became commonplace as the Industrial Revolution gathered pace. Thomas Telford adopted the material for his bridge upstream at Buildwas , and then for Longdon-on-Tern Aqueduct , a canal trough aqueduct at Longdon-on-Tern on the Shrewsbury Canal . It was followed by

Cape Neddick Light - Misplaced Pages Continue

2240-539: The bolt holes were also cast and not drilled. Thus, because of casting's draft angle, the tension from the tie bars was placed on the hole's edge rather than being spread over the length of the hole. The replacement bridge was built in wrought iron and steel. Further bridge collapses occurred, however, culminating in the Norwood Junction rail accident of 1891. Thousands of cast-iron rail underbridges were eventually replaced by steel equivalents by 1900 owing to

2310-522: The carbon in white cast iron precipitates out of the melt as the metastable phase cementite , Fe 3 C, rather than graphite. The cementite which precipitates from the melt forms as relatively large particles. As the iron carbide precipitates out, it withdraws carbon from the original melt, moving the mixture toward one that is closer to eutectic , and the remaining phase is the lower iron-carbon austenite (which on cooling might transform to martensite ). These eutectic carbides are much too large to provide

2380-439: The carbon to separate as spheroidal particles as the material solidifies. The properties are similar to malleable iron, but parts can be cast with larger sections. Cast iron and wrought iron can be produced unintentionally when smelting copper using iron ore as a flux. The earliest cast-iron artifacts date to the 5th century BC, and were discovered by archaeologists in what is now modern Luhe County , Jiangsu in China during

2450-627: The cotton, hemp , or wool being spun. As a result, textile mills had an alarming propensity to burn down. The solution was to build them completely of non-combustible materials, and it was found convenient to provide the building with an iron frame, largely of cast iron, replacing flammable wood. The first such building was at Ditherington in Shrewsbury , Shropshire. Many other warehouses were built using cast-iron columns and beams, although faulty designs, flawed beams or overloading sometimes caused building collapses and structural failures. During

2520-404: The crown of the pipe creating a much weaker section. In 1845, the first pipe was cast vertically in a pit and by the end of the century, all pipe was manufactured by this method. Using this method the slag would all collect at the top of the casting and could be removed by simply cutting off the end of the pipe. Pipes cast using this method often suffered from off centre bores caused by the core of

2590-599: The development of steel-framed skyscrapers. Cast iron was also used sometimes for decorative facades, especially in the United States, and the Soho district of New York has numerous examples. It was also used occasionally for complete prefabricated buildings, such as the historic Iron Building in Watervliet, New York . Another important use was in textile mills . The air in the mills contained flammable fibres from

2660-520: The effects of sulfur, manganese is added, because the two form into manganese sulfide instead of iron sulfide. The manganese sulfide is lighter than the melt, so it tends to float out of the melt and into the slag . The amount of manganese required to neutralize sulfur is 1.7 × sulfur content + 0.3%. If more than this amount of manganese is added, then manganese carbide forms, which increases hardness and chilling , except in grey iron, where up to 1% of manganese increases strength and density. Nickel

2730-513: The form in which its carbon appears: white cast iron has its carbon combined into an iron carbide named cementite , which is very hard, but brittle, as it allows cracks to pass straight through; grey cast iron has graphite flakes which deflect a passing crack and initiate countless new cracks as the material breaks, and ductile cast iron has spherical graphite "nodules" which stop the crack from further progressing. Carbon (C), ranging from 1.8 to 4 wt%, and silicon (Si), 1–3 wt%, are

2800-511: The gardens of the Chateau de Versailles. These amount to some 35 km of pipe, typically 1 m lengths with flanged joints. The extreme age of these pipes make them of considerable historical value. Despite extensive refurbishment in 2008 by Saint-Gobain PAM, 80% remain original. Cast iron proved to be a beneficial material for the manufacture of water pipes and was used as a replacement for

2870-525: The hands of intelligent extraterrestrials. Cape Neddick Light is one of the last eight lights in Maine to still have its Fresnel lens . It was added to the National Register of Historic Places as Cape Neddick Light Station on April 16, 1985, reference number 85000844. The lighthouse and island were featured in the movie Lost Boundaries (1949) starring Mel Ferrer . Although the origin of

Cape Neddick Light - Misplaced Pages Continue

2940-520: The inside ‘ceiling’ of the pipe. Starting in 1922, internal cement linings were introduced to act as a barrier to minimize internal corrosion. In 1929, the American Standard Association (ASA) Sectional Committee issued a tentative standard for cement-mortar linings, which was published in 1932. In 1939, American Standard A21.4 was published, which defined a Type I cement coating on the inside of waterline pipe to be used. When

3010-416: The island with his 19-pound (8.6 kg) cat who was an attraction in himself, especially when he reputedly swam across the channel to visit mainland friends. It is not always summer, though, and another story lends balance to lighthouse living. The Nubble is such a windy spot that in the winter, the temperature dropped so low that the flow of lamp oil to the incandescent oil vapor lamp was impeded. The problem

3080-546: The joints retain their integrity when subjected to limited subsidence . Typical joint deflections at mechanical joints today range anywhere from 3 to 5 degrees. Ball-and-socket joints introduced more "rounded" sockets, allowing a relatively large amount of deflection at each joint. This type of joint, still in use today, was considered a special-purpose joint, and has been used primarily in both submerged and mountainous terrain. This type of joint can typically allow around 15 degrees of deflection at each joint, making 'snaking' of

3150-662: The lighthouse and a gift shop with a "Nubble" theme. Nubble Light is a famous American icon and a classic example of a lighthouse. An image of the lighthouse is included on the Voyager Golden Record carried by the Voyager spacecraft as one of Earth's most prominent man-made structures or natural features, alongside features such as the Great Wall of China and the Taj Mahal , to be viewed should it fall into

3220-481: The lighthouse itself. The Cape Neddick Light stands on Nubble Island about 100 yards (91 m) off Cape Neddick Point. It is commonly known as "Nubble Light" or simply "the Nubble". Cape Neddick Point is at the north end of Long Sands Beach in the village of York Beach. The lighthouse is inaccessible to the general public, but the nearby mainland is occupied by Sohier Park which offers a telescope with which to view

3290-543: The little lighthouse adornments is unknown, there are many other stories about the Nubble Light. Among them is the story of the keeper and his wife who, in 1912, decided to take advantage of the booming tourist business at the York beaches. They developed a lively business ferrying tourists across to the island and giving tours. The trade grew so lively that the light was neglected and the keeper fired. Another keeper lived on

3360-539: The lower edge in tension, where cast iron, like masonry , is very weak. Nevertheless, cast iron continued to be used in inappropriate structural ways, until the Tay Rail Bridge disaster of 1879 cast serious doubt on the use of the material. Crucial lugs for holding tie bars and struts in the Tay Bridge had been cast integral with the columns, and they failed in the early stages of the accident. In addition,

3430-605: The main alloying elements of cast iron. Iron alloys with lower carbon content are known as steel . Cast iron tends to be brittle , except for malleable cast irons . With its relatively low melting point, good fluidity, castability , excellent machinability , resistance to deformation and wear resistance , cast irons have become an engineering material with a wide range of applications and are used in pipes , machines and automotive industry parts, such as cylinder heads , cylinder blocks and gearbox cases. Some alloys are resistant to damage by oxidation . In general, cast iron

3500-466: The melt before the final form is produced by casting . Cast iron is sometimes melted in a special type of blast furnace known as a cupola , but in modern applications, it is more often melted in electric induction furnaces or electric arc furnaces. After melting is complete, the molten cast iron is poured into a holding furnace or ladle. Cast iron's properties are changed by adding various alloying elements, or alloyants . Next to carbon , silicon

3570-508: The molten pig iron or by re-melting pig iron, often along with substantial quantities of iron, steel, limestone, carbon (coke) and taking various steps to remove undesirable contaminants. Phosphorus and sulfur may be burnt out of the molten iron, but this also burns out the carbon, which must be replaced. Depending on the application, carbon and silicon content are adjusted to the desired levels, which may be anywhere from 2–3.5% and 1–3%, respectively. If desired, other elements are then added to

SECTION 50

#1732787308870

3640-543: The mould being placed off centre, resulting in one side of the pipe being thicker than the other. Subsequent to its invention by Dimitri Sensaud deLavaud, a French-Brazilian, in 1918, much cast iron pipe manufacturing shifted to the dramatically different technique of centrifugal casting . Modern ductile iron pipe production continues to use this general method of casting. Historically, two different types of molds have been used in centrifugal casting of cast iron pipe: metal molds and sand molds. With metal molds, molten iron

3710-468: The original elm pipelines utilized earlier. These water pipelines were composed of individually cast pipe sections, often termed sticks, jointed together by a variety of joint mechanisms. Flanged joints consisted of flat machined surfaces that were tightly bolted together with a gasket between them to prevent leakage. This type of pipe joint is still in use today, typically for above-ground pipelines in water treatment and manufacturing plants. Cast iron pipe

3780-491: The pipe had solidified and the flask was removed. Cast iron pipe formed using this procedure was typically oven-cooled under controlled time and temperature conditions. As with metal molds, pipe was typically annealed to eliminate any stresses in the pipe, and were then cleaned, inspected, tested, gauged (for dimensions), coated internally and/or externally, and stored for use. Standards for cast-iron pipe centrifugally cast in sand molds for water were established and published by

3850-458: The pipe possible. The advantage of this joint type was that it was quicker than bell and spigot joints, and did not require special skills or tools to install. Push-on joints, developed in the mid 1950s, allowed a quicker and relatively non-skilled method of jointing pipe. This joint consisted of a bell with a recessed groove which held a rubberized gasket. A lubricated beveled spigot section can be pushed into this joint with care, as not to roll

3920-423: The pipe, and were then cleaned, inspected, tested, gauged (for dimensions), coated internally and/or externally, and stored for use. Standards for cast-iron pipe centrifugally cast in metal molds for water were established and published by the American Water Works Association. When cast with sand molds, two types of manufacturing processes were used. In the first method, a metal pattern was typically positioned in

3990-416: The pipe. Since the tubercles are irregularly shaped, buildup of bacterial growths on the surface are likely. As more iron moves into solution, the result is a loss of pipe structure over time potentially affecting pipe integrity. In storm and sanitary sewer systems , the creation of acidic gases (such as hydrogen sulfide ) by microbial action can further corrode internal pipe walls but is most pronounced on

4060-418: The properties of malleable cast iron are more like those of mild steel . There is a limit to how large a part can be cast in malleable iron, as it is made from white cast iron. Developed in 1948, nodular or ductile cast iron has its graphite in the form of very tiny nodules with the graphite in the form of concentric layers forming the nodules. As a result, the properties of ductile cast iron are that of

4130-762: The relationship between wood and stone. Cast-iron beam bridges were used widely by the early railways, such as the Water Street Bridge in 1830 at the Manchester terminus of the Liverpool and Manchester Railway , but problems with its use became all too apparent when a new bridge carrying the Chester and Holyhead Railway across the River Dee in Chester collapsed killing five people in May 1847, less than

4200-475: The retention of carbon and the formation of those carbides. Nickel and copper increase strength and machinability, but do not change the amount of graphite formed. Carbon as graphite produces a softer iron, reduces shrinkage, lowers strength, and decreases density. Sulfur , largely a contaminant when present, forms iron sulfide , which prevents the formation of graphite and increases hardness . Sulfur makes molten cast iron viscous, which causes defects. To counter

4270-446: The rubberized gasket, and once installed became watertight. This type of jointing system is popular today with ductile iron and polyvinyl chloride (PVC) pipes. The first cast iron pipe was produced in horizontal moulds, the core of the mould would be supported on small iron rods which would become part of the pipe. Horizontal casting resulted in an uneven distribution of metal around the pipe circumference. Typically slag would collect at

SECTION 60

#1732787308870

4340-497: The standard was updated in 1953, the Type I cement was replaced with Type II, since it was believed that Type II was a more closely controlled product. The standard was further revised in 1964, which included the use of either Type I or Type II cement, and making two different mortar thicknesses available. The first standardization of cast iron water pipes in Britain occurred in 1917 with the publishing of BS 78. This standard specified

4410-501: The technique of producing cast-iron cannons, which, while heavier than the prevailing bronze cannons, were much cheaper and enabled England to arm her navy better. Cast-iron pots were made at many English blast furnaces at the time. In 1707, Abraham Darby patented a new method of making pots (and kettles) thinner and hence cheaper than those made by traditional methods. This meant that his Coalbrookdale furnaces became dominant as suppliers of pots, an activity in which they were joined in

4480-566: The use of higher lime ratios, enabling the conversion from charcoal (supplies of wood for which were inadequate) to coke. The ironmasters of the Weald continued producing cast irons until the 1760s, and armament was one of the main uses of irons after the Restoration . The use of cast iron for structural purposes began in the late 1770s, when Abraham Darby III built The Iron Bridge , although short beams had already been used, such as in

4550-518: The widespread concern about cast iron under bridges on the rail network in Britain. Cast-iron columns , pioneered in mill buildings, enabled architects to build multi-storey buildings without the enormously thick walls required for masonry buildings of any height. They also opened up floor spaces in factories, and sight lines in churches and auditoriums. By the mid 19th century, cast iron columns were common in warehouse and industrial buildings, combined with wrought or cast iron beams, eventually leading to

4620-514: Was also produced. Numerous testimonies were made by early European missionaries of the Luba people pouring cast iron into molds to make hoes. These technological innovations were accomplished without the invention of the blast furnace which was the prerequisite for the deployment of such innovations in Europe and Asia. The technology of cast iron was transferred to the West from China. Al-Qazvini in

4690-421: Was frequently used uncoated, although later coatings and linings reduced corrosion and improved hydraulics. In cast iron pipe, the graphite forms flakes during the casting process, when examined under a microscope. Cast iron pipe was superseded by ductile iron pipe , which is a direct development, with most existing manufacturing plants transitioning to the new material during the 1970s and 1980s. Ductile iron pipe

4760-439: Was introduced into the mold to uniformly distribute metal over the interior of the mold surface by the centrifugal force generated. The outside mold was typically protected from damage by a controlled water bath or water spray system. When the pipe was cool enough to be handled and hold its shape, the mold was stopped and the pipe removed. Pipe formed in metal molds were typically annealed after casting to eliminate any stresses in

4830-410: Was more desirable, cast iron was cheaper and thus was more commonly used for implements in ancient China, while wrought iron or steel was used for weapons. The Chinese developed a method of annealing cast iron by keeping hot castings in an oxidizing atmosphere for a week or longer in order to burn off some carbon near the surface in order to keep the surface layer from being too brittle. Deep within

4900-403: Was solved in 1938 when the lamp was electrified. That same year, the outhouse was closed, and the keeper and his family also received indoor plumbing . Cast iron Cast iron is a class of iron – carbon alloys with a carbon content of more than 2% and silicon content around 1–3%. Its usefulness derives from its relatively low melting temperature. The alloying elements determine

#869130