Misplaced Pages

#581418

28-641: There are three configurations of the R4000: the R4000PC, an entry-level model with no support for a secondary cache; the R4000SC, a model with secondary cache but no multiprocessor capability; and the R4000MC, a model with secondary cache and support for the cache coherency protocols required by multiprocessor systems. The R4000 is a scalar superpipelined microprocessor with an eight-stage integer pipeline. During

56-470: A i486 -compatible bus. Scalar processor Scalar processors are a class of computer processors that process only one data item at a time. Typical data items include integers and floating point numbers . A scalar processor is classified as a single instruction, single data ( SISD ) processor in Flynn's taxonomy . The Intel 486 is an example of a scalar processor. It is to be contrasted with

84-414: A vector processor where a single instruction operates simultaneously on multiple data items (and thus is referred to as a single instruction, multiple data ( SIMD ) processor). The difference is analogous to the difference between scalar and vector arithmetic. The term scalar in computing dates to the 1970 and 1980s when vector processors were first introduced. It was originally used to distinguish

112-403: A 16- or 32-byte line size. Architecturally, it could be expanded to 32 KB. During the third stage (RF), the instruction is decoded and the register file is read. The MIPS III defines two register files, one for the integer unit and the other for floating-point. Each register file is 64 bits wide and contained 32 entries. The integer register file has two read ports and one write port, while

140-502: A 447-pin ceramic staggered pin grid array (SPGA). The pin out of the R4000MC is different from the R4000SC, with some pins which are unused on the R4000SC used for signals to implement cache coherency on the R4000MC. The pin-out of the R4000PC is similar to that of the PGA-packaged R4200 and R4600 microprocessors. This characteristic enables a properly designed system to use any of the three microprocessors. The R4400

168-408: A 64-bit carry-select adder and a logic unit and is pipelined. The shifter is a 32-bit barrel shifter . It performs 64-bit shifts in two cycles, stalling the pipeline as a result. This design was chosen to save die area. The multiplier and divider are not pipelined and have significant latencies: multiplies have a 10- or 20-cycle latency for 32-bit or 64-bit integers, respectively; whereas divides have

196-420: A 69- or 133-cycle latency for 32-bit or 64-bit integers, respectively. Most instructions have a single cycle latency. The ALU adder is also used for calculating virtual addresses for loads, stores and branches. Load and store instructions are executed by the integer pipeline, and access the on-chip 8 KB data cache. The R4000 has an on-die IEEE 754-1985 -compliant floating-point unit (FPU), referred to as

224-440: A capacity of 128 KB to 4 MB. The cache is accessed via a dedicated 128-bit data bus. The secondary cache can be configured either as a unified cache or as a split instruction and data cache. In the latter configuration, each cache can have a capacity of 128 KB to 2 MB. The secondary cache is physically indexed, physically tagged and has a programmable line size of 128, 256, 512 or 1,024 bytes. The cache controller

252-457: A computer supporting virtual memory , the term physical address is used mostly to differentiate from a virtual address . In particular, in computers utilizing a memory management unit (MMU) to translate memory addresses, the virtual and physical addresses refer to an address before and after translation performed by the MMU, respectively. Depending upon its underlying computer architecture ,

280-405: A multiplier. The Cortex-M7 , like many consumer CPUs today, is a superscalar processor. A scalar data type, or just scalar , is any non- composite value . Generally, all basic primitive data types are considered scalar: Some programming languages also treat strings as scalar types, while other languages treat strings as arrays or objects . This computer hardware article

308-408: Is a stub . You can help Misplaced Pages by expanding it . Physical address In computing , a physical address (also real address , or binary address ), is a memory address that is represented in the form of a binary number on the address bus circuitry in order to enable the data bus to access a particular storage cell of main memory , or a register of memory-mapped I/O device. In

SECTION 10

#1732771993582

336-581: Is a further development of the R4000. It was announced in early November 1992. Samples of the microprocessor had been shipped to selected customers before then, with general availability in January 1993. The R4400 operates at clock frequencies of 100, 133, 150, 200, and 250 MHz. The only major improvement from the R4000 is larger primary caches, which were doubled in capacity to 16 KB each from 8 KB each. It contained 2.3 million transistors. The R4400

364-456: Is capable of retiring one instruction per cycle. The adder and multiplier are pipelined. The multiplier has a four-stage multiplier pipeline. It is clocked at twice the clock frequency of the microprocessor for adequate performance and uses dynamic logic to achieve the high clock frequency. Division has a 23- or 36-cycle latency for single- or double-precision operations and square-root has a 54- or 112-cycle latency. Division and square-root uses

392-494: Is on-die. The cache is built from standard static random access memory (SRAM). The data and tag buses are ECC-protected. The R4000 uses a 64-bit system bus called the SysAD bus. The SysAD bus was an address and data multiplexed bus, that is, it used the same set of wires to transfer data and addresses. While this reduces bandwidth, it is also less expensive than providing a separate address bus, which requires more pins and increases

420-553: The SRT algorithm. The memory management unit (MMU) uses a 48-entry translation lookaside buffer to translate virtual addresses . The R4000 uses a 64-bit virtual address, but only implements 40 of the 64 bits, allowing 1 TB of virtual memory ; the remaining bits are checked to ensure that they contain zero. The R4000 uses a 36-bit physical address , thus is able to address 64 GB of physical memory . The R4000 (SC and MC configurations only) supports an external secondary cache with

448-495: The ALU unless there is a data or resource dependency, which causes it to stall. It contains three sub-units: an adder, a multiplier and a divider. The multiplier and divider can execute an instruction in parallel with the adder, but they use the adder in their final stages of execution, thus imposing limits to overlapping execution. Thus, under certain conditions, it can execute up to three instructions at any time, one in each unit. The FPU

476-443: The R4000 was fabricated by partners in their own processes, which had a 0.8 μm minimum feature size. The R4000 generates the various clock signals from a master clock signal generated externally. For the operating frequency, the R4000 multiplies the master clock signal by two by use of an on-die phase-locked loop (PLL). The R4000PC is packaged in a 179-pin ceramic pin grid array (CPGA). The R4000SC and R4000MC are packaged in

504-721: The R4010. The FPU is a coprocessor designated CP1 (the MIPS ISA defined four coprocessors, designated CP0 to CP3). The FPU can operate in two modes, 32- or 64-bit which are selected by setting a bit, the FR bit, in the CPU status register. In 32-bit mode, the 32 floating-point registers become 32 bits wide when used to hold single-precision floating-point numbers. When used to hold double-precision numbers, there are 16 floating-point registers (the registers are paired). The FPU can operate in parallel with

532-522: The R4400MC at $ 2,150 in quantities of 10,000. The R4400 is used by: The R4000 and R4400 microprocessors were interfaced to the system by custom ASICs or by commercially available chipsets. System vendors such as SGI developed their own ASICs for their systems. Commercial chipsets were developed, fabricated and marketed by companies such as Toshiba with their the Tiger Shark chipset, which provided

560-591: The VR4400. The first version, a 150 MHz part, was announced in November 1992. Early versions were fabricated in a 0.6 μm process. In mid-1995, a 250 MHz part began sampling. It was fabricated in a 0.35 μm four-layer-metal process. NEC also produced the MR4401, a ceramic multi-chip module (MCM) that contained a VR4400SC with ten 1 Mbit SRAM chips that implemented a 1 MB secondary cache. The MCM

588-413: The complexity of the system. The SysAD bus can be configured to operate at half, a third or a quarter of the internal clock frequency. The SysAD bus generates its clock signal by dividing the operating frequency. The R4000 contains 1.2 million transistors. It was designed for a 1.0 μm two-layer metal complementary metal–oxide–semiconductor (CMOS) process. As MIPS was a fabless company,

SECTION 20

#1732771993582

616-409: The first stage (IF), a virtual address for an instruction is generated and the instruction translation lookaside buffer (TLB) begins the translation of the address to a physical address. In the second stage (IS), translation is completed and the instruction is fetched from an internal 8 KB instruction cache. The instruction cache is direct-mapped and virtually indexed, physically tagged . It has

644-430: The floating-point register file has two read ports and two write ports. Execution begins at stage four (EX) for both integer and floating-point instructions; and is written back to the register files when completed in stage eight (WB). Results may be bypassed if possible. The R4000 has an arithmetic logic unit (ALU), a shifter, multiplier and divider and load aligner for executing integer instructions. The ALU consists of

672-462: The older designs from the new vector processors. A superscalar processor (such as the Intel P5 ) may execute more than one instruction during a clock cycle by simultaneously dispatching multiple instructions to redundant functional units on the processor. Each functional unit is not a separate CPU core but an execution resource within a single CPU such as an arithmetic logic unit, a bit shifter, or

700-410: The performance of a computer may be hindered by unaligned access to memory. For example, a 16-bit computer with a 16-bit memory data bus, such as Intel 8086 , generally has less overhead if the access is aligned to an even address. In that case fetching one 16-bit value requires a single memory read operation, a single transfer over a data bus. If the 16-bit data value starts at an odd address,

728-496: The processor may need to perform two memory read cycles to load the value into it, i.e. one for the low address (throwing away half of it) and then a second read cycle to load the high address (throwing away again half of the retrieved data). On some processors , such as the Motorola 68000 and Motorola 68010 processors, and SPARC processors, unaligned memory accesses will result in an exception being raised (usually resulting in

756-519: Was licensed by Integrated Device Technology (IDT), LSI Logic , NEC , Performance Semiconductor, Siemens AG and Toshiba . IDT, NEC, Siemens and Toshiba fabricated and marketed the microprocessor. LSI Logic used the R4400 in custom products. Performance Semiconductor sold their logic division to Cypress Semiconductor where the MIPS microprocessor products were discontinued. NEC marketed their version as

784-571: Was pin-compatible with the R4x00PC. The first version, a 150 MHz part, was announced in 1994. In 1995, a 200 MHz part was announced. Toshiba marketed their version as the TC86R4400. A 200 MHz part containing 2.3 million transistors and measuring 134 mm fabricated in a 0.3 μm process was introduced in mid-1994. The R4400PC was priced at $ 1,600 , the R4400SC at $ 1,950 , and

#581418