A turbofan or fanjet is a type of airbreathing jet engine that is widely used in aircraft propulsion . The word "turbofan" is a combination of references to the preceding generation engine technology of the turbojet and the additional fan stage. It consists of a gas turbine engine which achieves mechanical energy from combustion, and a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all the air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust .
156-528: The Rolls-Royce RB211 is a British family of high-bypass turbofan engines made by Rolls-Royce . The engines are capable of generating 41,030 to 59,450 lbf (182.5 to 264.4 kN) of thrust . The RB211 engine was the first production three-spool engine and turned Rolls-Royce from a significant player in the aero-engine industry into a global leader. Originally developed for the Lockheed L-1011 TriStar , it entered service in 1972 and
312-703: A constant power setting. Work on the RB211 as essentially a scaled-down RB207 began in 1966-7 with the first certificated engines being scheduled to be available by December 1970 at 33,260lb take-off thrust and at a price of $ 511,000 each. In February 1968, American Airlines had chosen the Rolls-Royce RB211 to power its order for up to 50 McDonnell-Douglas DC-10s. On 7 March 1968, the Washington correspondent of The Times wrote of an attempt being made by Congress to block Rolls-Royce's bid to supply engines for
468-434: A corresponding increase in pressure and temperature in the exhaust duct which in turn cause a higher gas speed from the propelling nozzle (and higher KE and wasted fuel). Although the engine would use less fuel to produce a pound of thrust, more fuel is wasted in the faster propelling jet. In other words, the independence of thermal and propulsive efficiencies, as exists with the piston engine/propeller combination which preceded
624-419: A discordant nature known as "buzz saw" noise. All modern turbofan engines have acoustic liners in the nacelle to damp their noise. They extend as much as possible to cover the largest surface area. The acoustic performance of the engine can be experimentally evaluated by means of ground tests or in dedicated experimental test rigs. In the aerospace industry, chevrons are the "saw-tooth" patterns on
780-419: A discordant nature known as "buzz saw" noise. All modern turbofan engines have acoustic liners in the nacelle to damp their noise. They extend as much as possible to cover the largest surface area. The acoustic performance of the engine can be experimentally evaluated by means of ground tests or in dedicated experimental test rigs. In the aerospace industry, chevrons are the "saw-tooth" patterns on
936-516: A few weeks on the RB211 he came to understand that £50 million is peanuts." – Stanley Hooker. The RB211's initial reliability in service was not as good as had been expected because of the focus of the development programme on meeting the engine's performance guarantees. Early deliveries were of the RB211-22C model, derated slightly from the later -22B. A programme of modifications during the first few years in service improved matters considerably, and
1092-410: A fixed total applied fuel:air ratio, the total fuel flow for a given fan airflow will be the same, regardless of the dry specific thrust of the engine. However, a high specific thrust turbofan will, by definition, have a higher nozzle pressure ratio, resulting in a higher afterburning net thrust and, therefore, a lower afterburning specific fuel consumption (SFC). However, high specific thrust engines have
1248-410: A fixed total applied fuel:air ratio, the total fuel flow for a given fan airflow will be the same, regardless of the dry specific thrust of the engine. However, a high specific thrust turbofan will, by definition, have a higher nozzle pressure ratio, resulting in a higher afterburning net thrust and, therefore, a lower afterburning specific fuel consumption (SFC). However, high specific thrust engines have
1404-519: A full cowl nacelle with deep-chute forced mixer as already present on the -535E4. These were the first versions to feature FADEC . This was later adopted by GE and Pratt & Whitney for their engines. The -524H was also offered as a third engine choice on the Boeing 767 , and the first of these entered service with British Airways in February 1990. These would have been the final developments of
1560-426: A high dry SFC. The situation is reversed for a medium specific thrust afterburning turbofan: i.e., poor afterburning SFC/good dry SFC. The former engine is suitable for a combat aircraft which must remain in afterburning combat for a fairly long period, but has to fight only fairly close to the airfield (e.g. cross border skirmishes). The latter engine is better for an aircraft that has to fly some distance, or loiter for
1716-426: A high dry SFC. The situation is reversed for a medium specific thrust afterburning turbofan: i.e., poor afterburning SFC/good dry SFC. The former engine is suitable for a combat aircraft which must remain in afterburning combat for a fairly long period, but has to fight only fairly close to the airfield (e.g. cross border skirmishes). The latter engine is better for an aircraft that has to fly some distance, or loiter for
SECTION 10
#17327722133571872-416: A higher nozzle pressure ratio than the turbojet, but with a lower exhaust temperature to retain net thrust. Since the temperature rise across the whole engine (intake to nozzle) would be lower, the (dry power) fuel flow would also be reduced, resulting in a better specific fuel consumption (SFC). Some low-bypass ratio military turbofans (e.g. F404 , JT8D ) have variable inlet guide vanes to direct air onto
2028-416: A higher nozzle pressure ratio than the turbojet, but with a lower exhaust temperature to retain net thrust. Since the temperature rise across the whole engine (intake to nozzle) would be lower, the (dry power) fuel flow would also be reduced, resulting in a better specific fuel consumption (SFC). Some low-bypass ratio military turbofans (e.g. F404 , JT8D ) have variable inlet guide vanes to direct air onto
2184-590: A long time, before going into combat. However, the pilot can afford to stay in afterburning only for a short period, before aircraft fuel reserves become dangerously low. The first production afterburning turbofan engine was the Pratt & Whitney TF30 , which initially powered the F-111 Aardvark and F-14 Tomcat . Low-bypass military turbofans include the Pratt & Whitney F119 , the Eurojet EJ200 ,
2340-414: A long time, before going into combat. However, the pilot can afford to stay in afterburning only for a short period, before aircraft fuel reserves become dangerously low. The first production afterburning turbofan engine was the Pratt & Whitney TF30 , which initially powered the F-111 Aardvark and F-14 Tomcat . Low-bypass military turbofans include the Pratt & Whitney F119 , the Eurojet EJ200 ,
2496-401: A pound of thrust, more fuel is wasted in the faster propelling jet. In other words, the independence of thermal and propulsive efficiencies, as exists with the piston engine/propeller combination which preceded the turbojet, is lost. In contrast, Roth considers regaining this independence the single most important feature of the turbofan which allows specific thrust to be chosen independently of
2652-403: A pure-jet of the same thrust, and jet noise is no longer the predominant source. Turbofan engine noise propagates both upstream via the inlet and downstream via the primary nozzle and the by-pass duct. Other noise sources are the fan, compressor and turbine. Modern commercial aircraft employ high-bypass-ratio (HBPR) engines with separate flow, non-mixing, short-duct exhaust systems. Their noise
2808-403: A pure-jet of the same thrust, and jet noise is no longer the predominant source. Turbofan engine noise propagates both upstream via the inlet and downstream via the primary nozzle and the by-pass duct. Other noise sources are the fan, compressor and turbine. Modern commercial aircraft employ high-bypass-ratio (HBPR) engines with separate flow, non-mixing, short-duct exhaust systems. Their noise
2964-550: A series of triple-spool designs as replacements for the Conway, which promised to deliver higher efficiency. In this configuration , three groups of turbines spin three separate concentric shafts to power three sections of the compressor area running at different speeds. In addition to allowing each stage of the compressor to run at its optimal speed, the triple-spool design is more compact and rigid, although more complex to build and maintain. Several designs were being worked on at
3120-569: A static thrust of 4,320 lb (1,960 kg), and had a bypass ratio of 6:1. The General Electric TF39 became the first production model, designed to power the Lockheed C-5 Galaxy military transport aircraft. The civil General Electric CF6 engine used a derived design. Other high-bypass turbofans are the Pratt & Whitney JT9D , the three-shaft Rolls-Royce RB211 and the CFM International CFM56 ; also
3276-424: A static thrust of 4,320 lb (1,960 kg), and had a bypass ratio of 6:1. The General Electric TF39 became the first production model, designed to power the Lockheed C-5 Galaxy military transport aircraft. The civil General Electric CF6 engine used a derived design. Other high-bypass turbofans are the Pratt & Whitney JT9D , the three-shaft Rolls-Royce RB211 and the CFM International CFM56 ; also
SECTION 20
#17327722133573432-473: A turbofan engine is the ratio between the mass flow rate of the bypass stream to the mass flow rate entering the core. A bypass ratio of 6, for example, means that 6 times more air passes through the bypass duct than the amount that passes through the combustion chamber. Turbofan engines are usually described in terms of BPR, which together with overall pressure ratio, turbine inlet temperature and fan pressure ratio are important design parameters. In addition BPR
3588-473: A turbofan engine is the ratio between the mass flow rate of the bypass stream to the mass flow rate entering the core. A bypass ratio of 6, for example, means that 6 times more air passes through the bypass duct than the amount that passes through the combustion chamber. Turbofan engines are usually described in terms of BPR, which together with overall pressure ratio, turbine inlet temperature and fan pressure ratio are important design parameters. In addition BPR
3744-421: A turbojet engine uses all of the engine's output to produce thrust in the form of a hot high-velocity exhaust gas jet, a turbofan's cool low-velocity bypass air yields between 30% and 70% of the total thrust produced by a turbofan system. The thrust ( F N ) generated by a turbofan depends on the effective exhaust velocity of the total exhaust, as with any jet engine, but because two exhaust jets are present
3900-421: A turbojet engine uses all of the engine's output to produce thrust in the form of a hot high-velocity exhaust gas jet, a turbofan's cool low-velocity bypass air yields between 30% and 70% of the total thrust produced by a turbofan system. The thrust ( F N ) generated by a turbofan depends on the effective exhaust velocity of the total exhaust, as with any jet engine, but because two exhaust jets are present
4056-496: A turbojet even though an extra turbine, a gearbox and a propeller are added to the turbojet's low-loss propelling nozzle. The turbofan has additional losses from its greater number of compressor stages/blades, fan and bypass duct. Froude, or propulsive, efficiency can be defined as: η f = 2 1 + V j V a {\displaystyle \eta _{f}={\frac {2}{1+{\frac {V_{j}}{V_{a}}}}}} where: While
4212-496: A turbojet even though an extra turbine, a gearbox and a propeller are added to the turbojet's low-loss propelling nozzle. The turbofan has additional losses from its greater number of compressor stages/blades, fan and bypass duct. Froude, or propulsive, efficiency can be defined as: η f = 2 1 + V j V a {\displaystyle \eta _{f}={\frac {2}{1+{\frac {V_{j}}{V_{a}}}}}} where: While
4368-704: A turbojet which accelerates a smaller amount more quickly, which is a less efficient way to generate the same thrust (see the efficiency section below). The ratio of the mass-flow of air bypassing the engine core compared to the mass-flow of air passing through the core is referred to as the bypass ratio . Engines with more jet thrust relative to fan thrust are known as low-bypass turbofans , those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are high-bypass, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofans on combat aircraft. The bypass ratio (BPR) of
4524-704: A turbojet which accelerates a smaller amount more quickly, which is a less efficient way to generate the same thrust (see the efficiency section below). The ratio of the mass-flow of air bypassing the engine core compared to the mass-flow of air passing through the core is referred to as the bypass ratio . Engines with more jet thrust relative to fan thrust are known as low-bypass turbofans , those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are high-bypass, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofans on combat aircraft. The bypass ratio (BPR) of
4680-431: A type of airbreathing jet engine that is widely used in aircraft propulsion . The word "turbofan" is a combination of references to the preceding generation engine technology of the turbojet and the additional fan stage. It consists of a gas turbine engine which achieves mechanical energy from combustion, and a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all
4836-507: Is best suited to high supersonic speeds. If it is all transferred to a separate big mass of air with low kinetic energy, the aircraft is best suited to zero speed (hovering). For speeds in between, the gas power is shared between a separate airstream and the gas turbine's own nozzle flow in a proportion which gives the aircraft performance required. The trade off between mass flow and velocity is also seen with propellers and helicopter rotors by comparing disc loading and power loading. For example,
Rolls-Royce RB211 - Misplaced Pages Continue
4992-507: Is best suited to high supersonic speeds. If it is all transferred to a separate big mass of air with low kinetic energy, the aircraft is best suited to zero speed (hovering). For speeds in between, the gas power is shared between a separate airstream and the gas turbine's own nozzle flow in a proportion which gives the aircraft performance required. The trade off between mass flow and velocity is also seen with propellers and helicopter rotors by comparing disc loading and power loading. For example,
5148-410: Is considerable potential for reducing fuel consumption for the same core cycle by increasing BPR.This is achieved because of the reduction in pounds of thrust per lb/sec of airflow (specific thrust) and the resultant reduction in lost kinetic energy in the jets (increase in propulsive efficiency). If all the gas power from a gas turbine is converted to kinetic energy in a propelling nozzle, the aircraft
5304-410: Is considerable potential for reducing fuel consumption for the same core cycle by increasing BPR.This is achieved because of the reduction in pounds of thrust per lb/sec of airflow (specific thrust) and the resultant reduction in lost kinetic energy in the jets (increase in propulsive efficiency). If all the gas power from a gas turbine is converted to kinetic energy in a propelling nozzle, the aircraft
5460-430: Is due to the speed, temperature, and pressure of the exhaust jet, especially during high-thrust conditions, such as those required for takeoff. The primary source of jet noise is the turbulent mixing of shear layers in the engine's exhaust. These shear layers contain instabilities that lead to highly turbulent vortices that generate the pressure fluctuations responsible for sound. To reduce the noise associated with jet flow,
5616-430: Is due to the speed, temperature, and pressure of the exhaust jet, especially during high-thrust conditions, such as those required for takeoff. The primary source of jet noise is the turbulent mixing of shear layers in the engine's exhaust. These shear layers contain instabilities that lead to highly turbulent vortices that generate the pressure fluctuations responsible for sound. To reduce the noise associated with jet flow,
5772-444: Is emphasised by Qantas ' adoption of RB.211-524 power for its new Boeing 747s – the only aircraft on which all big three fans are available. Qantas found that British Airways' Boeing 747s fitted with RB211s burnt roughly 7% less fuel than its JT9D-equipped fleet, a saving of about $ 1 million a year per aircraft, at today's prices." Rolls-Royce continued to develop the -524, increasing its thrust through 51,500 lbf (229 kN) with
5928-413: Is quoted for turboprop and unducted fan installations because their high propulsive efficiency gives them the overall efficiency characteristics of very high bypass turbofans. This allows them to be shown together with turbofans on plots which show trends of reducing specific fuel consumption (SFC) with increasing BPR. BPR can also be quoted for lift fan installations where the fan airflow is remote from
6084-413: Is quoted for turboprop and unducted fan installations because their high propulsive efficiency gives them the overall efficiency characteristics of very high bypass turbofans. This allows them to be shown together with turbofans on plots which show trends of reducing specific fuel consumption (SFC) with increasing BPR. BPR can also be quoted for lift fan installations where the fan airflow is remote from
6240-420: Is sufficient core power to drive the fan. A smaller core flow/higher bypass ratio cycle can be achieved by raising the inlet temperature of the high-pressure (HP) turbine rotor. To illustrate one aspect of how a turbofan differs from a turbojet, comparisons can be made at the same airflow (to keep a common intake for example) and the same net thrust (i.e. same specific thrust). A bypass flow can be added only if
6396-420: Is sufficient core power to drive the fan. A smaller core flow/higher bypass ratio cycle can be achieved by raising the inlet temperature of the high-pressure (HP) turbine rotor. To illustrate one aspect of how a turbofan differs from a turbojet, comparisons can be made at the same airflow (to keep a common intake for example) and the same net thrust (i.e. same specific thrust). A bypass flow can be added only if
Rolls-Royce RB211 - Misplaced Pages Continue
6552-424: Is that combustion is less efficient at lower speeds. Any action to reduce the fuel consumption of the engine by increasing its pressure ratio or turbine temperature to achieve better combustion causes a corresponding increase in pressure and temperature in the exhaust duct which in turn cause a higher gas speed from the propelling nozzle (and higher KE and wasted fuel). Although the engine would use less fuel to produce
6708-411: Is very fuel intensive. Consequently, afterburning can be used only for short portions of a mission. Unlike in the main engine, where stoichiometric temperatures in the combustor have to be reduced before they reach the turbine, an afterburner at maximum fuelling is designed to produce stoichiometric temperatures at entry to the nozzle, about 2,100 K (3,800 °R; 3,300 °F; 1,800 °C). At
6864-411: Is very fuel intensive. Consequently, afterburning can be used only for short portions of a mission. Unlike in the main engine, where stoichiometric temperatures in the combustor have to be reduced before they reach the turbine, an afterburner at maximum fuelling is designed to produce stoichiometric temperatures at entry to the nozzle, about 2,100 K (3,800 °R; 3,300 °F; 1,800 °C). At
7020-479: The Bristol Olympus , and Pratt & Whitney JT3C engines, increased the overall pressure ratio and thus the thermodynamic efficiency of engines. They also had poor propulsive efficiency, because pure turbojets have a high specific thrust/high velocity exhaust, which is better suited to supersonic flight. The original low-bypass turbofan engines were designed to improve propulsive efficiency by reducing
7176-415: The Bristol Olympus , and Pratt & Whitney JT3C engines, increased the overall pressure ratio and thus the thermodynamic efficiency of engines. They also had poor propulsive efficiency, because pure turbojets have a high specific thrust/high velocity exhaust, which is better suited to supersonic flight. The original low-bypass turbofan engines were designed to improve propulsive efficiency by reducing
7332-702: The General Electric F110 , the Klimov RD-33 , and the Saturn AL-31 , all of which feature a mixed exhaust, afterburner and variable area propelling nozzle. To further improve fuel economy and reduce noise, almost all jet airliners and most military transport aircraft (e.g., the C-17 ) are powered by low-specific-thrust/high-bypass-ratio turbofans. These engines evolved from the high-specific-thrust/low-bypass-ratio turbofans used in such aircraft in
7488-460: The General Electric F110 , the Klimov RD-33 , and the Saturn AL-31 , all of which feature a mixed exhaust, afterburner and variable area propelling nozzle. To further improve fuel economy and reduce noise, almost all jet airliners and most military transport aircraft (e.g., the C-17 ) are powered by low-specific-thrust/high-bypass-ratio turbofans. These engines evolved from the high-specific-thrust/low-bypass-ratio turbofans used in such aircraft in
7644-484: The Trent 700 . The -535E4 is considered by many to be an extremely reliable engine, and achieved 180-minute ETOPS approval on the 757 in 1990. When Rolls-Royce was developing the -22, it realised that it would be straightforward to develop a version of the engine for land-based power generation , and in 1974 the industrial RB211 was launched. When the -524 arrived shortly afterwards, its improvements were incorporated in
7800-520: The bypass ratio . The engine produces thrust through a combination of these two portions working together. Engines that use more jet thrust relative to fan thrust are known as low-bypass turbofans ; conversely those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are of the high-bypass type, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofan engines with bypass and core mixing before
7956-518: The -524, but when Rolls developed the successor Trent engine, it was found it could fit the Trent 700's improved HP system to the -524G and -524H. These variants were lighter and offered improved fuel efficiency and reduced emissions; they were designated -524G-T and -524H-T respectively. It was also possible to upgrade existing -524G/H engines to the improved -T configuration, and a number of airlines did this. The -524 became increasingly reliable as it
SECTION 50
#17327722133578112-411: The -524C, then 53,000 lbf (240 kN) in the -524D which was certificated in 1981. Notable airline customers included Qantas , Cathay Pacific , Air New Zealand , Cargolux and South African Airways . When Boeing launched the heavier 747-400 more thrust was required, and Rolls responded with the -524G rated at 58,000 lbf (260 kN) thrust and then the -524H with 60,600, both introducing
8268-543: The -535C for the PW2037 version. Boeing put Rolls-Royce under pressure to supply a more competitive engine for the 757, and using the more advanced -524 core as a basis, the company produced the 40,100 lbf (178,000 N) thrust RB211-535E4 which entered service in October 1984. While not as efficient as the PW2037, it was more reliable and quieter. Visible differences include a long cowl with no jet nozzle protruding beyond
8424-421: The 1960s. Modern combat aircraft tend to use low-bypass ratio turbofans, and some military transport aircraft use turboprops . Low specific thrust is achieved by replacing the multi-stage fan with a single-stage unit. Unlike some military engines, modern civil turbofans lack stationary inlet guide vanes in front of the fan rotor. The fan is scaled to achieve the desired net thrust. The core (or gas generator) of
8580-421: The 1960s. Modern combat aircraft tend to use low-bypass ratio turbofans, and some military transport aircraft use turboprops . Low specific thrust is achieved by replacing the multi-stage fan with a single-stage unit. Unlike some military engines, modern civil turbofans lack stationary inlet guide vanes in front of the fan rotor. The fan is scaled to achieve the desired net thrust. The core (or gas generator) of
8736-641: The E4 was offered on the Russian Tupolev Tu-204-120 airliner, entering service in 1992. This was the first time a Russian airliner had been supplied with western engines. The -535E4 was also proposed by Boeing for re-engining the B-52H Stratofortress , replacing the aircraft's eight TF33s with four of the turbofans. Further upgrading of the -535E4 took place in the late 1990s to reduce emissions, borrowing technology developed for
8892-661: The L-1011, as well as the Boeing 747 . Rolls-Royce tried unsuccessfully to sell the RB211 to Boeing in the 1960s, but the new -524 offered significant performance and efficiency improvements over the Pratt & Whitney JT9D which Boeing had originally selected to power the 747. In October 1973 Boeing agreed to offer the RB211-524 on the 747-200, and British Airways became the first airline to order this combination which entered service in 1977. Flight International stated in 1980: "The importance placed on fuel saving by airlines
9048-643: The RB.178 was £2.6 million. As a comparison, the GE and P&W companies were awarded nearly $ 20 million by the US Department of Defense to develop and build the TF39 and STF200 technology demonstrators. The RB.178 was built on the reliable and economic advantages inherent in the Conway and, given that engine's heritage, the new engine's performance looked certain. The RB.178 (designated the 16 series) appears to have been
9204-710: The RB211-06 for the L-1011 . The new engine was to be rated at 33,260 lbf (147,900 N) thrust and combined features of several engines then under development: the large high-power, high-bypass design from the RB207 and the triple-spool design of the RB203. To this was added one new piece of technology, a fan stage built of a new carbon fibre material called Hyfil developed at the RAE Farnborough . The weight saving
9360-464: The aerospace industry has sought to disrupt shear layer turbulence and reduce the overall noise produced. Fan noise may come from the interaction of the fan-blade wakes with the pressure field of the downstream fan-exit stator vanes. It may be minimized by adequate axial spacing between blade trailing edge and stator entrance. At high engine speeds, as at takeoff, shock waves from the supersonic fan tips, because of their unequal nature, produce noise of
9516-464: The aerospace industry has sought to disrupt shear layer turbulence and reduce the overall noise produced. Fan noise may come from the interaction of the fan-blade wakes with the pressure field of the downstream fan-exit stator vanes. It may be minimized by adequate axial spacing between blade trailing edge and stator entrance. At high engine speeds, as at takeoff, shock waves from the supersonic fan tips, because of their unequal nature, produce noise of
SECTION 60
#17327722133579672-422: The afterburner, raising the temperature of exhaust gases by a significant degree, resulting in a higher exhaust velocity/engine specific thrust. The variable geometry nozzle must open to a larger throat area to accommodate the extra volume and increased flow rate when the afterburner is lit. Afterburning is often designed to give a significant thrust boost for take off, transonic acceleration and combat maneuvers, but
9828-422: The afterburner, raising the temperature of exhaust gases by a significant degree, resulting in a higher exhaust velocity/engine specific thrust. The variable geometry nozzle must open to a larger throat area to accommodate the extra volume and increased flow rate when the afterburner is lit. Afterburning is often designed to give a significant thrust boost for take off, transonic acceleration and combat maneuvers, but
9984-409: The afterburner. Modern turbofans have either a large single-stage fan or a smaller fan with several stages. An early configuration combined a low-pressure turbine and fan in a single rear-mounted unit. The turbofan was invented to improve the fuel consumption of the turbojet. It achieves this by pushing more air, thus increasing the mass and lowering the speed of the propelling jet compared to that of
10140-404: The air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust . The ratio of the mass-flow of air bypassing the engine core to the mass-flow of air passing through the core is referred to as
10296-441: The aircraft is going forwards, leaving a very fast wake. This wake contains kinetic energy that reflects the fuel used to produce it, rather than the fuel used to move the aircraft forwards. A turbofan harvests that wasted velocity and uses it to power a ducted fan that blows air in bypass channels around the rest of the turbine. This reduces the speed of the propelling jet while pushing more air, and thus more mass. The other penalty
10452-516: The assets of Rolls-Royce from the Receiver, and shortly afterwards signed a new contract with Lockheed. This revised agreement cancelled penalties for late delivery, and increased the price of each engine by £110,000. Hugh Conway (managing director RR Gas Turbines), persuaded Stanley Hooker to come out of retirement and return to Rolls-Royce. As technical director he led a team of other retirees - including Cyril Lovesey and Arthur Rubbra - to fix
10608-474: The average stage loading and to maintain LP turbine efficiency. Reducing core flow also increases bypass ratio. Bypass ratios greater than 5:1 are increasingly common; the Pratt & Whitney PW1000G , which entered commercial service in 2016, attains 12.5:1. Further improvements in core thermal efficiency can be achieved by raising the overall pressure ratio of the core. Improvements in blade aerodynamics can reduce
10764-426: The average stage loading and to maintain LP turbine efficiency. Reducing core flow also increases bypass ratio. Bypass ratios greater than 5:1 are increasingly common; the Pratt & Whitney PW1000G , which entered commercial service in 2016, attains 12.5:1. Further improvements in core thermal efficiency can be achieved by raising the overall pressure ratio of the core. Improvements in blade aerodynamics can reduce
10920-497: The bypass duct. Partial mixing of hot and cold airflows takes place in the integrated or common nozzle. It was also the first to use a wide chord fan blade which increases efficiency, reduces noise and gives added protection against foreign object damage . Probably the most important single -535E order came in May 1988 when American Airlines ordered 50 757s powered by the -535E4 citing the engine's low noise as an important factor: this
11076-448: The engine and doesn't flow past the engine core. Considering a constant core (i.e. fixed pressure ratio and turbine inlet temperature), core and bypass jet velocities equal and a particular flight condition (i.e. Mach number and altitude) the fuel consumption per lb of thrust (sfc) decreases with increase in BPR. At the same time gross and net thrusts increase, but by different amounts. There
11232-399: The engine and doesn't flow past the engine core. Considering a constant core (i.e. fixed pressure ratio and turbine inlet temperature), core and bypass jet velocities equal and a particular flight condition (i.e. Mach number and altitude) the fuel consumption per lb of thrust (sfc) decreases with increase in BPR. At the same time gross and net thrusts increase, but by different amounts. There
11388-523: The engine had insufficient thrust, was over weight and its fuel consumption was excessive. The situation deteriorated further when in May 1970 the new Hyfil (a carbon fibre composite) fan stage, after passing other tests, shattered when a chicken carcass was fired into it at high speed as part of the bird ingestion test. The company had been developing a titanium blade as an insurance against difficulties with Hyfil , but this meant extra cost and more weight. It also brought its own technical problems when it
11544-427: The engine must generate enough power to drive the fan at its rated mass flow and pressure ratio. Improvements in turbine cooling/material technology allow for a higher (HP) turbine rotor inlet temperature, which allows a smaller (and lighter) core, potentially improving the core thermal efficiency. Reducing the core mass flow tends to increase the load on the LP turbine, so this unit may require additional stages to reduce
11700-427: The engine must generate enough power to drive the fan at its rated mass flow and pressure ratio. Improvements in turbine cooling/material technology allow for a higher (HP) turbine rotor inlet temperature, which allows a smaller (and lighter) core, potentially improving the core thermal efficiency. Reducing the core mass flow tends to increase the load on the LP turbine, so this unit may require additional stages to reduce
11856-877: The engine proposed for the Vickers Superb DB.265 ( VC10 ), with four engines powering the high capacity transatlantic airliner. There are perhaps many reasons why the RB.178 failed. Chief among them was Boeing declining to offer the Rolls-Royce engine on the 747. The RB.178 was cancelled in May 1966 and in June 1966 Rolls-Royce indicated it did not want to battle with P&W over the Boeing 747. In September 1966 Rolls-Royce revealed its decision to launch an Advanced Technology Engine (A.T.E) family covering thrusts ranging from 10,000lbf (RB.203) through to 60,000lbf. (RB.207). The A.T.E family introduced new technologies such as
12012-416: The engine, from the gas generator, to a ducted fan which produces a second, additional mass of accelerated air. The transfer of energy from the core to bypass air results in lower pressure and temperature gas entering the core nozzle (lower exhaust velocity), and fan-produced higher pressure and temperature bypass-air entering the fan nozzle. The amount of energy transferred depends on how much pressure rise
12168-524: The exhaust velocity to a value closer to that of the aircraft. The Rolls-Royce Conway , the world's first production turbofan, had a bypass ratio of 0.3, similar to the modern General Electric F404 fighter engine. Civilian turbofan engines of the 1960s, such as the Pratt & Whitney JT8D and the Rolls-Royce Spey , had bypass ratios closer to 1 and were similar to their military equivalents. The first Soviet airliner powered by turbofan engines
12324-458: The exhaust velocity to a value closer to that of the aircraft. The Rolls-Royce Conway , the world's first production turbofan, had a bypass ratio of 0.3, similar to the modern General Electric F404 fighter engine. Civilian turbofan engines of the 1960s, such as the Pratt & Whitney JT8D and the Rolls-Royce Spey , had bypass ratios closer to 1 and were similar to their military equivalents. The first Soviet airliner powered by turbofan engines
12480-411: The fan is designed to produce (fan pressure ratio). The best energy exchange (lowest fuel consumption) between the two flows, and how the jet velocities compare, depends on how efficiently the transfer takes place which depends on the losses in the fan-turbine and fan. The fan flow has lower exhaust velocity, giving much more thrust per unit energy (lower specific thrust ). Both airstreams contribute to
12636-494: The fan nozzle. The amount of energy transferred depends on how much pressure rise the fan is designed to produce (fan pressure ratio). The best energy exchange (lowest fuel consumption) between the two flows, and how the jet velocities compare, depends on how efficiently the transfer takes place which depends on the losses in the fan-turbine and fan. The fan flow has lower exhaust velocity, giving much more thrust per unit energy (lower specific thrust ). Both airstreams contribute to
12792-450: The first fan rotor stage. This improves the fan surge margin (see compressor map ). Since the 1970s, most jet fighter engines have been low/medium bypass turbofans with a mixed exhaust, afterburner and variable area exit nozzle. An afterburner is a combustor located downstream of the turbine blades and directly upstream of the nozzle, which burns fuel from afterburner-specific fuel injectors. When lit, large volumes of fuel are burnt in
12948-450: The first fan rotor stage. This improves the fan surge margin (see compressor map ). Since the 1970s, most jet fighter engines have been low/medium bypass turbofans with a mixed exhaust, afterburner and variable area exit nozzle. An afterburner is a combustor located downstream of the turbine blades and directly upstream of the nozzle, which burns fuel from afterburner-specific fuel injectors. When lit, large volumes of fuel are burnt in
13104-561: The first generation three-engine jets. According to Cownie, Gunston, Hayward and the UK Department of Trade & Industry (DTI), the roots of the advanced RB.178 go back to 1961 when Rolls-Royce officially initiated work on a high by-pass ratio aero-engine as a replacement for the Conway . The company went ahead with the project and under the leadership of Adrian Lombard built the twin-spool demonstrator. Overall development costs of
13260-483: The fuel consumption of the turbojet. It achieves this by pushing more air, thus increasing the mass and lowering the speed of the propelling jet compared to that of the turbojet. This is done mechanically by adding a ducted fan rather than using viscous forces. A vacuum ejector is used in conjunction with the fan as first envisaged by inventor Frank Whittle . Whittle envisioned flight speeds of 500 mph in his March 1936 UK patent 471,368 "Improvements relating to
13416-496: The fuel used to move the aircraft forwards. A turbofan harvests that wasted velocity and uses it to power a ducted fan that blows air in bypass channels around the rest of the turbine. This reduces the speed of the propelling jet while pushing more air, and thus more mass. The other penalty is that combustion is less efficient at lower speeds. Any action to reduce the fuel consumption of the engine by increasing its pressure ratio or turbine temperature to achieve better combustion causes
13572-400: The gas generator cycle. The working substance of the thermodynamic cycle is the only mass accelerated to produce thrust in a turbojet which is a serious limitation (high fuel consumption) for aircraft speeds below supersonic. For subsonic flight speeds the speed of the propelling jet has to be reduced because there is a price to be paid in producing the thrust. The energy required to accelerate
13728-443: The gas inside the engine (increase in kinetic energy) is expended in two ways, by producing a change in momentum ( i.e. a force), and a wake which is an unavoidable consequence of producing thrust by an airbreathing engine (or propeller). The wake velocity, and fuel burned to produce it, can be reduced and the required thrust still maintained by increasing the mass accelerated. A turbofan does this by transferring energy available inside
13884-429: The gross thrust of the engine. The additional air for the bypass stream increases the ram drag in the air intake stream-tube, but there is still a significant increase in net thrust. The overall effective exhaust velocity of the two exhaust jets can be made closer to a normal subsonic aircraft's flight speed and gets closer to the ideal Froude efficiency . A turbofan accelerates a larger mass of air more slowly, compared to
14040-429: The gross thrust of the engine. The additional air for the bypass stream increases the ram drag in the air intake stream-tube, but there is still a significant increase in net thrust. The overall effective exhaust velocity of the two exhaust jets can be made closer to a normal subsonic aircraft's flight speed and gets closer to the ideal Froude efficiency . A turbofan accelerates a larger mass of air more slowly, compared to
14196-409: The high-bypass type, and most modern fighter engines are low-bypass. Afterburners are used on low-bypass turbofan engines with bypass and core mixing before the afterburner. Modern turbofans have either a large single-stage fan or a smaller fan with several stages. An early configuration combined a low-pressure turbine and fan in a single rear-mounted unit. The turbofan was invented to improve
14352-474: The hot nozzle to convert to kinetic energy. Turbofans represent an intermediate stage between turbojets , which derive all their thrust from exhaust gases, and turbo-props which derive minimal thrust from exhaust gases (typically 10% or less). Extracting shaft power and transferring it to a bypass stream introduces extra losses which are more than made up by the improved propulsive efficiency. The turboprop at its best flight speed gives significant fuel savings over
14508-474: The hot nozzle to convert to kinetic energy. Turbofans represent an intermediate stage between turbojets , which derive all their thrust from exhaust gases, and turbo-props which derive minimal thrust from exhaust gases (typically 10% or less). Extracting shaft power and transferring it to a bypass stream introduces extra losses which are more than made up by the improved propulsive efficiency. The turboprop at its best flight speed gives significant fuel savings over
14664-405: The industrial RB211 which was designated RB211-24. The generator was gradually developed over the following years and is still marketed today as a range of generators producing 25.2–32 MW. Many of its installations have been in the offshore oil and gas production industries. An advanced 25 MW class WR-21 Intercooled Recuperated (ICR) gas turbine was derived for marine propulsion. The -535E4
14820-468: The mass-flow of air bypassing the engine core to the mass-flow of air passing through the core is referred to as the bypass ratio . The engine produces thrust through a combination of these two portions working together. Engines that use more jet thrust relative to fan thrust are known as low-bypass turbofans ; conversely those that have considerably more fan thrust than jet thrust are known as high-bypass . Most commercial aviation jet engines in use are of
14976-417: The mechanical power produced by the turbine. In a bypass design, extra turbines drive a ducted fan that accelerates air rearward from the front of the engine. In a high-bypass design, the ducted fan and nozzle produce most of the thrust. Turbofans are closely related to turboprops in principle because both transfer some of the gas turbine's gas power, using extra machinery, to a bypass stream leaving less for
15132-417: The mechanical power produced by the turbine. In a bypass design, extra turbines drive a ducted fan that accelerates air rearward from the front of the engine. In a high-bypass design, the ducted fan and nozzle produce most of the thrust. Turbofans are closely related to turboprops in principle because both transfer some of the gas turbine's gas power, using extra machinery, to a bypass stream leaving less for
15288-411: The mid 1970s, Boeing was considering designs for a new twin-engined aircraft to replace its successful 727 . As the size of the proposed plane grew from 150 passengers towards 200, Rolls-Royce realised that the RB211 could be adapted by reducing the diameter of the fan and removing the first IP compressor stage to produce an engine with the necessary 37,400 lbf (166,000 N) thrust. The new version
15444-483: The number of extra compressor stages required, and variable geometry stators enable high-pressure-ratio compressors to work surge-free at all throttle settings. The first (experimental) high-bypass turbofan engine was the AVCO-Lycoming PLF1A-2, a Honeywell T55 turboshaft-derived engine that was first run in February 1962. The PLF1A-2 had a 40 in diameter (100 cm) geared fan stage, produced
15600-411: The number of extra compressor stages required, and variable geometry stators enable high-pressure-ratio compressors to work surge-free at all throttle settings. The first (experimental) high-bypass turbofan engine was the AVCO-Lycoming PLF1A-2, a Honeywell T55 turboshaft-derived engine that was first run in February 1962. The PLF1A-2 had a 40 in diameter (100 cm) geared fan stage, produced
15756-414: The point of arrogance, had slid from bad to worse when their great leader, Lombard, had been so suddenly plucked from them in 1967. His death had left a vacuum which nobody could fill ... " – Stanley Hooker In September 1970, Rolls-Royce reported to the government that development costs for the RB211 had risen to £170.3 million – nearly double the original estimate. The estimated production costs now exceeded
15912-420: The projected United States airbus. Representative Robert Taft Jr. of Ohio had marshalled opposition because of a report that Rolls-Royce had won approval for the engine. On 9 March 1968, The Times reported that President Lyndon Johnson had received written protests from six senators and five representatives, from Ohio and New Mexico – states that would benefit if a US manufacturer was selected. Their complaint
16068-414: The propulsion of aircraft", in which he describes the principles behind the turbofan, although not called as such at that time. While the turbojet uses the gas from its thermodynamic cycle as its propelling jet, for aircraft speeds below 500 mph there are two penalties to this design which are addressed by the turbofan. Firstly, energy is wasted as the propelling jet is going much faster rearwards than
16224-526: The remaining problems on the RB211-22. The engine was finally certified on 14 April 1972, about a year later than originally planned, and the first TriStar entered service with Eastern Air Lines on 26 April 1972. Hooker was knighted for his role in 1974. Speaking of a famous banker in relation to the RB211: "We (Rolls-Royce) added a zero to his stature; he used to think £5 million a lot of money, but after
16380-622: The required 45,000 lbf (200 kN) thrust class for an abortive attempt to introduce an updated Hawker Siddeley Trident as the RB178 . This work was later developed for the 47,500 lbf (211 kN) thrust RB207 to be used on the Airbus A300 , before, with the withdrawal of the UK from the Airbus programme, it was cancelled in favour of the RB211 programme. Rolls-Royce was also working on
16536-467: The required thrust still maintained by increasing the mass accelerated. A turbofan does this by transferring energy available inside the engine, from the gas generator, to a ducted fan which produces a second, additional mass of accelerated air. The transfer of energy from the core to bypass air results in lower pressure and temperature gas entering the core nozzle (lower exhaust velocity), and fan-produced higher pressure and temperature bypass-air entering
16692-428: The response was a 35,400 lbf (157,000 N) thrust version of the RB211 designated RB211-10. There followed a period of intense negotiation between airframe manufacturers Lockheed and Douglas, engine suppliers Rolls-Royce, General Electric and Pratt & Whitney , and the major US airlines. During this time prices were negotiated downwards and the required thrust ratings were increased. By early 1968, Rolls-Royce
16848-399: The same helicopter weight can be supported by a high power engine and small diameter rotor or, for less fuel, a lower power engine and bigger rotor with lower velocity through the rotor. Bypass usually refers to transferring gas power from a gas turbine to a bypass stream of air to reduce fuel consumption and jet noise. Alternatively, there may be a requirement for an afterburning engine where
17004-399: The same helicopter weight can be supported by a high power engine and small diameter rotor or, for less fuel, a lower power engine and bigger rotor with lower velocity through the rotor. Bypass usually refers to transferring gas power from a gas turbine to a bypass stream of air to reduce fuel consumption and jet noise. Alternatively, there may be a requirement for an afterburning engine where
17160-535: The series has since matured into a highly reliable engine. Although originally designed for the L-1011-1, Rolls-Royce knew that the RB211 could be developed to provide greater thrust. By redesigning the fan and the IP compressor, Hooker's team increased the engine's thrust to 50,000 lbf (220 kN). The new version, which first ran on 1 October 1973, was designated RB211-524, and would be able to power new variants of
17316-406: The significant increases in passenger numbers and air traffic which were then being forecast by the industry. In Europe, large capacity airliner concept studies had been carried out by both private and government organisations since the late 1950s and early 1960s. Many of the studies conducted by the aviation companies were weighted towards a 200 to 300 seat aircraft, with a high cycle performance that
17472-524: The smaller TF34 . More recent large high-bypass turbofans include the Pratt & Whitney PW4000 , the three-shaft Rolls-Royce Trent , the General Electric GE90 / GEnx and the GP7000 , produced jointly by GE and P&W. The Pratt & Whitney JT9D engine was the first high bypass ratio jet engine to power a wide-body airliner. High bypass turbofan A turbofan or fanjet is
17628-502: The sole requirement for bypass is to provide cooling air. This sets the lower limit for BPR and these engines have been called "leaky" or continuous bleed turbojets (General Electric YJ-101 BPR 0.25) and low BPR turbojets (Pratt & Whitney PW1120). Low BPR (0.2) has also been used to provide surge margin as well as afterburner cooling for the Pratt & Whitney J58 . Propeller engines are most efficient for low speeds, turbojet engines for high speeds, and turbofan engines between
17784-502: The sole requirement for bypass is to provide cooling air. This sets the lower limit for BPR and these engines have been called "leaky" or continuous bleed turbojets (General Electric YJ-101 BPR 0.25) and low BPR turbojets (Pratt & Whitney PW1120). Low BPR (0.2) has also been used to provide surge margin as well as afterburner cooling for the Pratt & Whitney J58 . Propeller engines are most efficient for low speeds, turbojet engines for high speeds, and turbofan engines between
17940-454: The speed of the propelling jet has to be reduced because there is a price to be paid in producing the thrust. The energy required to accelerate the gas inside the engine (increase in kinetic energy) is expended in two ways, by producing a change in momentum ( i.e. a force), and a wake which is an unavoidable consequence of producing thrust by an airbreathing engine (or propeller). The wake velocity, and fuel burned to produce it, can be reduced and
18096-536: The technology and materials available at the time. The first turbofan engine, which was only run on a test bed, was the German Daimler-Benz DB 670 , designated the 109-007 by the German RLM ( Ministry of Aviation ), with a first run date of 27 May 1943, after the testing of the turbomachinery using an electric motor, which had been undertaken on 1 April 1943. Development of the engine
18252-402: The technology and materials available at the time. The first turbofan engine, which was only run on a test bed, was the German Daimler-Benz DB 670 , designated the 109-007 by the German RLM ( Ministry of Aviation ), with a first run date of 27 May 1943, after the testing of the turbomachinery using an electric motor, which had been undertaken on 1 April 1943. Development of the engine
18408-497: The thrust equation can be expanded as: F N = m ˙ e v h e − m ˙ o v o + B P R ( m ˙ c ) v f {\displaystyle F_{N}={\dot {m}}_{e}v_{he}-{\dot {m}}_{o}v_{o}+BPR\,({\dot {m}}_{c})v_{f}} where: The cold duct and core duct's nozzle systems are relatively complex due to
18564-497: The thrust equation can be expanded as: F N = m ˙ e v h e − m ˙ o v o + B P R ( m ˙ c ) v f {\displaystyle F_{N}={\dot {m}}_{e}v_{he}-{\dot {m}}_{o}v_{o}+BPR\,({\dot {m}}_{c})v_{f}} where: The cold duct and core duct's nozzle systems are relatively complex due to
18720-669: The time, including a 10,000 lbf (44 kN) thrust design known as the RB203 intended to replace the Spey . Work started on the Conway replacement engine in July 1961 and a twin-spool demonstrator engine to prove the HP compressor, combustor, and turbine system designs, had been run by 1966. Rolls-Royce chose the triple-spool system in 1965 as the simplest, lowest cost solution to the problem of obtaining lower fuel consumption and reduced noise levels at
18876-729: The time, this demanded three engines to provide redundancy. Other airlines also favored three engines. Lockheed and Douglas responded with designs, the L-1011 TriStar and DC-10 respectively. Both had three engines, transcontinental range and seated around 300 passengers in a widebody layout with two aisles. The wide-body McDonnell-Douglas DC-10 was representative of the innovative aircraft and aero-engine technologies which were then being adopted by US and European airframe manufacturers to provide airlines with aircraft of very large carrying capacity and short/medium to long range. These very large capacity aircraft were needed to address
19032-673: The trailing edges of some jet engine nozzles that are used for noise reduction . The shaped edges smooth the mixing of hot air from the engine core and cooler air flowing through the engine fan, which reduces noise-creating turbulence. Chevrons were developed by GE under a NASA contract. Some notable examples of such designs are Boeing 787 and Boeing 747-8 – on the Rolls-Royce Trent 1000 and General Electric GEnx engines. Early turbojet engines were not very fuel-efficient because their overall pressure ratio and turbine inlet temperature were severely limited by
19188-606: The trailing edges of some jet engine nozzles that are used for noise reduction . The shaped edges smooth the mixing of hot air from the engine core and cooler air flowing through the engine fan, which reduces noise-creating turbulence. Chevrons were developed by GE under a NASA contract. Some notable examples of such designs are Boeing 787 and Boeing 747-8 – on the Rolls-Royce Trent 1000 and General Electric GEnx engines. Early turbojet engines were not very fuel-efficient because their overall pressure ratio and turbine inlet temperature were severely limited by
19344-403: The triple-shaft architecture, an annular combustor and a structurally integrated power-plant (nacelle). Both planes also required new engines. Engines were undergoing a period of rapid advance due to the introduction of the high bypass concept, which provided for greater thrust, improved fuel economy and less noise than the earlier low-bypass designs. Rolls-Royce had been working on an engine of
19500-428: The turbine inlet temperature is not too high to compensate for the smaller core flow. Future improvements in turbine cooling/material technology can allow higher turbine inlet temperature, which is necessary because of increased cooling air temperature, resulting from an overall pressure ratio increase. The resulting turbofan, with reasonable efficiencies and duct loss for the added components, would probably operate at
19656-428: The turbine inlet temperature is not too high to compensate for the smaller core flow. Future improvements in turbine cooling/material technology can allow higher turbine inlet temperature, which is necessary because of increased cooling air temperature, resulting from an overall pressure ratio increase. The resulting turbofan, with reasonable efficiencies and duct loss for the added components, would probably operate at
19812-425: The turbojet uses the gas from its thermodynamic cycle as its propelling jet, for aircraft speeds below 500 mph there are two penalties to this design which are addressed by the turbofan. Firstly, energy is wasted as the propelling jet is going much faster rearwards than the aircraft is going forwards, leaving a very fast wake. This wake contains kinetic energy that reflects the fuel used to produce it, rather than
19968-445: The turbojet, is lost. In contrast, Roth considers regaining this independence the single most important feature of the turbofan which allows specific thrust to be chosen independently of the gas generator cycle. The working substance of the thermodynamic cycle is the only mass accelerated to produce thrust in a turbojet which is a serious limitation (high fuel consumption) for aircraft speeds below supersonic. For subsonic flight speeds
20124-453: The turbojet. This is done mechanically by adding a ducted fan rather than using viscous forces. A vacuum ejector is used in conjunction with the fan as first envisaged by inventor Frank Whittle . Whittle envisioned flight speeds of 500 mph in his March 1936 UK patent 471,368 "Improvements relating to the propulsion of aircraft", in which he describes the principles behind the turbofan, although not called as such at that time. While
20280-476: The two flows may combine within the ducts, and share a common nozzle, which can be fitted with afterburner. Most of the air flow through a high-bypass turbofan is lower-velocity bypass flow: even when combined with the much-higher-velocity engine exhaust, the average exhaust velocity is considerably lower than in a pure turbojet. Turbojet engine noise is predominately jet noise from the high exhaust velocity. Therefore, turbofan engines are significantly quieter than
20436-476: The two flows may combine within the ducts, and share a common nozzle, which can be fitted with afterburner. Most of the air flow through a high-bypass turbofan is lower-velocity bypass flow: even when combined with the much-higher-velocity engine exhaust, the average exhaust velocity is considerably lower than in a pure turbojet. Turbojet engine noise is predominately jet noise from the high exhaust velocity. Therefore, turbofan engines are significantly quieter than
20592-418: The two. Turbofans are the most efficient engines in the range of speeds from about 500 to 1,000 km/h (270 to 540 kn; 310 to 620 mph), the speed at which most commercial aircraft operate. In a turbojet (zero-bypass) engine, the high temperature and high pressure exhaust gas is accelerated when it undergoes expansion through a propelling nozzle and produces all the thrust. The compressor absorbs
20748-418: The two. Turbofans are the most efficient engines in the range of speeds from about 500 to 1,000 km/h (270 to 540 kn; 310 to 620 mph), the speed at which most commercial aircraft operate. In a turbojet (zero-bypass) engine, the high temperature and high pressure exhaust gas is accelerated when it undergoes expansion through a propelling nozzle and produces all the thrust. The compressor absorbs
20904-510: The use of two separate exhaust flows. In high bypass engines, the fan is situated in a short duct near the front of the engine and typically has a convergent cold nozzle, with the tail of the duct forming a low pressure ratio nozzle that under normal conditions will choke creating supersonic flow patterns around the core . The core nozzle is more conventional, but generates less of the thrust, and depending on design choices, such as noise considerations, may conceivably not choke. In low bypass engines
21060-510: The use of two separate exhaust flows. In high bypass engines, the fan is situated in a short duct near the front of the engine and typically has a convergent cold nozzle, with the tail of the duct forming a low pressure ratio nozzle that under normal conditions will choke creating supersonic flow patterns around the core . The core nozzle is more conventional, but generates less of the thrust, and depending on design choices, such as noise considerations, may conceivably not choke. In low bypass engines
21216-701: The world, with an experience base of over 10 million service hours. The CF700 turbofan engine was also used to train Moon-bound astronauts in Project Apollo as the powerplant for the Lunar Landing Research Vehicle . A high-specific-thrust/low-bypass-ratio turbofan normally has a multi-stage fan behind inlet guide vanes, developing a relatively high pressure ratio and, thus, yielding a high (mixed or cold) exhaust velocity. The core airflow needs to be large enough to ensure there
21372-495: The world, with an experience base of over 10 million service hours. The CF700 turbofan engine was also used to train Moon-bound astronauts in Project Apollo as the powerplant for the Lunar Landing Research Vehicle . A high-specific-thrust/low-bypass-ratio turbofan normally has a multi-stage fan behind inlet guide vanes, developing a relatively high pressure ratio and, thus, yielding a high (mixed or cold) exhaust velocity. The core airflow needs to be large enough to ensure there
21528-541: The £230,375 selling price of each engine. The project was in crisis. By January 1971 Rolls-Royce had become insolvent , and on 4 February 1971 was placed into receivership , seriously jeopardising the L-1011 TriStar programme. Because of its strategic importance, the company was nationalised by the Conservative government of Edward Heath , allowing development of the RB211 to be completed. As Lockheed
21684-614: Was abandoned with its problems unsolved, as the war situation worsened for Germany. Later in 1943, the British ground tested the Metrovick F.3 turbofan, which used the Metrovick F.2 turbojet as a gas generator with the exhaust discharging into a close-coupled aft-fan module comprising a contra-rotating LP turbine system driving two co-axial contra-rotating fans. Improved materials, and the introduction of twin compressors, such as in
21840-446: Was abandoned with its problems unsolved, as the war situation worsened for Germany. Later in 1943, the British ground tested the Metrovick F.3 turbofan, which used the Metrovick F.2 turbojet as a gas generator with the exhaust discharging into a close-coupled aft-fan module comprising a contra-rotating LP turbine system driving two co-axial contra-rotating fans. Improved materials, and the introduction of twin compressors, such as in
21996-510: Was based on the utilisation of the game-changing new technology of the high by-pass ratio aero-engine. Between 1964 and 1967, Hawker Siddeley 's examination of British European Airways (BEA)'s requirements produced the 160-seat HS.132 and the 185-seat HS.134; both offered the prospect of a 25–30% reduction in seat mile costs over aircraft then in service. Both of the designs would have used two new-technology Rolls-Royce RB.178 aero-engines of 30,000lbf to provide superior operating performance over
22152-551: Was considerable over a similar fan made of titanium, and gave the RB211 an advantage over its competitors in terms of power-to-weight ratio . Despite knowing that the timetable was challenging for an engine incorporating these new features, Rolls-Royce committed to putting the RB211 into service in 1971. Lockheed felt that the new engine enabled the L-1011 to offer a distinct advantage over the otherwise similar DC-10 product. However, Douglas had also requested proposals from Rolls-Royce for an engine to power its DC-10, and in October 1967
22308-660: Was derived from the General Electric J85/CJ610 turbojet 2,850 lbf (12,700 N) to power the larger Rockwell Sabreliner 75/80 model aircraft, as well as the Dassault Falcon 20 , with about a 50% increase in thrust to 4,200 lbf (19,000 N). The CF700 was the first small turbofan to be certified by the Federal Aviation Administration (FAA). There were at one time over 400 CF700 aircraft in operation around
22464-431: Was derived from the General Electric J85/CJ610 turbojet 2,850 lbf (12,700 N) to power the larger Rockwell Sabreliner 75/80 model aircraft, as well as the Dassault Falcon 20 , with about a 50% increase in thrust to 4,200 lbf (19,000 N). The CF700 was the first small turbofan to be certified by the Federal Aviation Administration (FAA). There were at one time over 400 CF700 aircraft in operation around
22620-556: Was designated RB211-535. On 31 August 1978 Eastern Airlines and British Airways announced orders for the new 757 , powered by the -535. Designated RB211-535C, the engine entered service in January 1983. This was the first time that Rolls-Royce had provided a launch engine on a Boeing aircraft. Eastern Airlines president Frank Borman called the -535C "The finest airline engine in the world". In 1979 Pratt & Whitney launched its PW2000 engine, claiming 8% better fuel efficiency than
22776-478: Was developed, and the -524H achieved 180-minute ETOPS approval on the 767 in 1993. An RB211 may have a thrust specific fuel consumption around 0.6 lb/(lbf·h). The -524L, begun in 1987 to allow further growth in the A330 and 777 market, was more extensively redesigned, the considerable differences incorporated leading to the engine eventually receiving the name Trent , under which name development has continued. In
22932-504: Was discovered that only one side of the titanium billet was of the right metallurgical quality for blade fabrication. In addition, the project suffered a setback with the death of Chief Engineer Adrian "Lom" Lombard in July 1967, a loss that was described as Rolls-Royce having been "deprived of one of the finest trouble-shooting engineers in the industry". "It was all too obvious that the Derby engineers, normally proud and self-confident to
23088-478: Was itself in a vulnerable position, the British government required that the US government guarantee the bank loans that Lockheed needed to complete the L-1011 project. If Lockheed (which was itself weakened by the difficulties) had failed, the market for the RB211 would have evaporated. Despite some opposition, the US government provided these guarantees. In May 1971, a new company called "Rolls-Royce (1971) Ltd." acquired
23244-425: Was offering a 40,600 lbf (181,000 N) thrust engine designated RB211-18. On 29 March 1968 Lockheed announced that it had received orders for 94 TriStars, and placed an order with Rolls-Royce for 150 sets of engines designated RB211-22. The RB211's complexity required a lengthy development and testing period. By Autumn 1969 Rolls-Royce was struggling to meet the performance guarantees to which it had committed:
23400-587: Was renamed, in 1989, to become the basis of the Rolls-Royce Trent family of engines when the RB211-524L was renamed to the Trent. In 1966, American Airlines announced a requirement for a new short-medium range airliner with a focus on low-cost per-seat operations. While it was looking for a twin-engined plane, aircraft manufacturers needed more than one customer to justify developing a new airliner. Eastern Airlines had expressed interest, but required greater range and needed to operate long routes over water. At
23556-553: Was that 'not adequately balanced information was given during talks between representatives of airlines and the British Government concerning the American Government's position on buying foreign engines'. The US Congress was concerned that the import of foreign engines would result in a US payments deficit of $ 3,800 million and the loss of 18,000 to 20,000 jobs. On 23 June 1967, Rolls-Royce offered Lockheed
23712-587: Was the Tupolev Tu-124 introduced in 1962. It used the Soloviev D-20 . 164 aircraft were produced between 1960 and 1965 for Aeroflot and other Eastern Bloc airlines, with some operating until the early 1990s. The first General Electric turbofan was the aft-fan CJ805-23 , based on the CJ805-3 turbojet. It was followed by the aft-fan General Electric CF700 engine, with a 2.0 bypass ratio. This
23868-407: Was the Tupolev Tu-124 introduced in 1962. It used the Soloviev D-20 . 164 aircraft were produced between 1960 and 1965 for Aeroflot and other Eastern Bloc airlines, with some operating until the early 1990s. The first General Electric turbofan was the aft-fan CJ805-23 , based on the CJ805-3 turbojet. It was followed by the aft-fan General Electric CF700 engine, with a 2.0 bypass ratio. This
24024-437: Was the exclusive engine to power the L-1011. Mismanagement of the initial development and consequent cost issues led to the effective nationalisation of Rolls-Royce Limited , to save the workforce and the engine businesses important to the UK and many other aerospace and aircraft operating companies. In the early 1970s, the engine was reckoned by the company to be capable of at least 50 years of continuous development. The RB.211
24180-404: Was the first engine to incorporate a hollow wide-chord unsnubbered fan to improve efficiency. It used advanced materials, including titanium in the HP compressor and carbon composites in the nacelle . Later engines incorporate some features (e.g. FADEC ) from improved models of the -524. Related development Comparable engines Related lists High-bypass turbofan The ratio of
24336-462: Was the first time since the TriStar that Rolls-Royce had received a significant order from a US airline, and it led to the -535E4's subsequent market domination on the 757. Unusually, at the time of the announcement made by American, selection of the -535E4 was made public prior to the selection of the 757, though this was welcome news to both Rolls-Royce and Boeing. After being certified for the 757,
#356643