131-541: The Vauxhall Light 6 is an automobile which was produced by Vauxhall in the United Kingdom from 1933 to 1938. Based on the Vauxhall Cadet the new car had a smaller version of the existing engine created by lengthening the stroke to 100 mm and reducing the bore to 57 mm for the 1530 cc ASY and 61.5 mm for the 1781 cc ASX. With overhead valves and Zenith down-draught carburetor
262-536: A Flemish member of a Jesuit mission in China around 1672. It was a 65-centimetre-long (26 in) scale-model toy for the Kangxi Emperor that was unable to carry a driver or a passenger. It is not known with certainty if Verbiest's model was successfully built or run. Nicolas-Joseph Cugnot is widely credited with building the first full-scale, self-propelled mechanical vehicle in about 1769; he created
393-433: A carburetor or fuel injection as port injection or direct injection . Most SI engines have a single spark plug per cylinder but some have 2 . A head gasket prevents the gas from leaking between the cylinder head and the engine block. The opening and closing of the valves is controlled by one or several camshafts and springs—or in some engines—a desmodromic mechanism that uses no springs. The camshaft may press directly
524-409: A deflector head . Pistons are open at the bottom and hollow except for an integral reinforcement structure (the piston web). When an engine is working, the gas pressure in the combustion chamber exerts a force on the piston crown which is transferred through its web to a gudgeon pin . Each piston has rings fitted around its circumference that mostly prevent the gases from leaking into the crankcase or
655-428: A gas engine . Also in 1794, Robert Street patented an internal combustion engine, which was also the first to use liquid fuel , and built an engine around that time. In 1798, John Stevens built the first American internal combustion engine. In 1807, French engineers Nicéphore Niépce (who went on to invent photography ) and Claude Niépce ran a prototype internal combustion engine, using controlled dust explosions,
786-470: A locomotive operated by electricity.) In boating, an internal combustion engine that is installed in the hull is referred to as an engine, but the engines that sit on the transom are referred to as motors. Reciprocating piston engines are by far the most common power source for land and water vehicles , including automobiles , motorcycles , ships and to a lesser extent, locomotives (some are electrical but most use diesel engines ). Rotary engines of
917-410: A rotor (Wankel engine) , or a nozzle ( jet engine ). This force moves the component over a distance. This process transforms chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to. The first commercially successful internal combustion engine was created by Étienne Lenoir around 1860, and the first modern internal combustion engine, known as
1048-407: A Fiat vehicle. Toyota , Nissan , Suzuki , Mazda , and Honda began as companies producing non-automotive products before the war, switching to car production during the 1950s. Kiichiro Toyoda's decision to take Toyoda Loom Works into automobile manufacturing would create what would eventually become Toyota Motor Corporation , the largest automobile manufacturer in the world. Subaru , meanwhile,
1179-594: A battery and charging system; nevertheless, this system is secondary and is added by manufacturers as a luxury for the ease of starting, turning fuel on and off (which can also be done via a switch or mechanical apparatus), and for running auxiliary electrical components and accessories. Most new engines rely on electrical and electronic engine control units (ECU) that also adjust the combustion process to increase efficiency and reduce emissions. Surfaces in contact and relative motion to other surfaces require lubrication to reduce wear, noise and increase efficiency by reducing
1310-404: A carefully timed high-voltage to the proper cylinder. This spark, via the spark plug, ignites the air-fuel mixture in the engine's cylinders. While gasoline internal combustion engines are much easier to start in cold weather than diesel engines, they can still have cold weather starting problems under extreme conditions. For years, the solution was to park the car in heated areas. In some parts of
1441-437: A combination of the use of feet and hands, and occasionally by voice on 21st-century cars. These controls include a steering wheel , pedals for operating the brakes and controlling the car's speed (and, in a manual transmission car, a clutch pedal), a shift lever or stick for changing gears, and a number of buttons and dials for turning on lights, ventilation, and other functions. Modern cars' controls are now standardised, such as
SECTION 10
#17327795562831572-499: A common power source for lawnmowers , string trimmers , chain saws , leafblowers , pressure washers , snowmobiles , jet skis , outboard motors , mopeds , and motorcycles . There are several possible ways to classify internal combustion engines. By number of strokes: By type of ignition: By mechanical/thermodynamic cycle (these cycles are infrequently used but are commonly found in hybrid vehicles , along with other vehicles manufactured for fuel efficiency ): The base of
1703-452: A hand crank. Larger engines typically power their starting motors and ignition systems using the electrical energy stored in a lead–acid battery . The battery's charged state is maintained by an automotive alternator or (previously) a generator which uses engine power to create electrical energy storage. The battery supplies electrical power for starting when the engine has a starting motor system, and supplies electrical power when
1834-483: A long-established wagon and coach manufacturer, started to build cars in 1897 and commenced sales of electric vehicles in 1902 and petrol vehicles in 1904. In Britain, there had been several attempts to build steam cars with varying degrees of success, with Thomas Rickett even attempting a production run in 1860. Santler from Malvern is recognised by the Veteran Car Club of Great Britain as having made
1965-670: A new model DMG car was produced and the model was named Mercedes after the Maybach engine, which generated 35 hp. Maybach quit DMG shortly thereafter and opened a business of his own. Rights to the Daimler brand name were sold to other manufacturers. In 1890, Émile Levassor and Armand Peugeot of France began producing vehicles with Daimler engines, and so laid the foundation of the automotive industry in France . In 1891, Auguste Doriot and his Peugeot colleague Louis Rigoulot completed
2096-408: A problem would occur as the compression ratio increased as the fuel was igniting due to the rise in temperature that resulted. Charles Kettering developed a lead additive which allowed higher compression ratios, which was progressively abandoned for automotive use from the 1970s onward, partly due to lead poisoning concerns. The fuel mixture is ignited at different progressions of the piston in
2227-423: A quarter of world oil production as of 2019 . Both petrol and diesel cars pollute more than electric cars. Cars and vans caused 8% of direct carbon dioxide emissions in 2021. As of 2021 , due to greenhouse gases emitted during battery production, electric cars must be driven tens of thousands of kilometres before their lifecycle carbon emissions are less than fossil fuel cars; however this varies considerably and
2358-731: A reciprocating internal combustion engine is the engine block , which is typically made of cast iron (due to its good wear resistance and low cost) or aluminum . In the latter case, the cylinder liners are made of cast iron or steel, or a coating such as nikasil or alusil . The engine block contains the cylinders . In engines with more than one cylinder they are usually arranged either in 1 row ( straight engine ) or 2 rows ( boxer engine or V engine ); 3 or 4 rows are occasionally used ( W engine ) in contemporary engines, and other engine configurations are possible and have been used. Single-cylinder engines (or thumpers ) are common for motorcycles and other small engines found in light machinery. On
2489-419: A result, Ford's cars came off the line in 15-minute intervals, much faster than previous methods, increasing productivity eightfold, while using less manpower (from 12.5 manhours to 1 hour 33 minutes). It was so successful, paint became a bottleneck. Only Japan black would dry fast enough, forcing the company to drop the variety of colours available before 1913, until fast-drying Duco lacquer
2620-422: A separate ICE as an auxiliary power unit . Wankel engines are fitted to many unmanned aerial vehicles . ICEs drive large electric generators that power electrical grids. They are found in the form of combustion turbines with a typical electrical output in the range of some 100 MW. Combined cycle power plants use the high temperature exhaust to boil and superheat water steam to run a steam turbine . Thus,
2751-481: A separate blower avoids many of the shortcomings of crankcase scavenging, at the expense of increased complexity which means a higher cost and an increase in maintenance requirement. An engine of this type uses ports or valves for intake and valves for exhaust, except opposed piston engines , which may also use ports for exhaust. The blower is usually of the Roots-type but other types have been used too. This design
SECTION 20
#17327795562832882-416: A separate crankcase ventilation system. The cylinder head is attached to the engine block by numerous bolts or studs . It has several functions. The cylinder head seals the cylinders on the side opposite to the pistons; it contains short ducts (the ports ) for intake and exhaust and the associated intake valves that open to let the cylinder be filled with fresh air and exhaust valves that open to allow
3013-467: A steam-powered road vehicle. It was unable to maintain sufficient steam pressure for long periods and was of little practical use. The development of external combustion (steam) engines is detailed as part of the history of the car but often treated separately from the development of true cars. A variety of steam-powered road vehicles were used during the first part of the 19th century, including steam cars , steam buses , phaetons , and steam rollers . In
3144-544: A steam-powered tricycle. He also constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts . His inventions were limited by problems with water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of
3275-579: A three-wheeled car powered by electricity at the International Exposition of Electricity . Although several other German engineers (including Gottlieb Daimler , Wilhelm Maybach , and Siegfried Marcus ) were working on cars at about the same time, the year 1886 is regarded as the birth year of the modern car—a practical, marketable automobile for everyday use—when the German Carl Benz patented his Benz Patent-Motorwagen ; he
3406-673: A way to head off on unchaperoned dates, plus they had a private space to snuggle up close at the end of the night." Similarly the costs to society of car use may include; maintaining roads , land use , air pollution , noise pollution , road congestion , public health , health care, and of disposing of the vehicle at the end of its life; and can be balanced against the value of the benefits to society that car use generates. Societal benefits may include: economy benefits, such as job and wealth creation, of car production and maintenance, transportation provision, society wellbeing derived from leisure and travel opportunities, and revenue generation from
3537-460: Is a heat engine in which the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high- temperature and high- pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons ( piston engine ), turbine blades ( gas turbine ),
3668-474: Is a motor vehicle with wheels . Most definitions of cars state that they run primarily on roads , seat one to eight people, have four wheels , and mainly transport people over cargo . There are around one billion cars in use worldwide. The French inventor Nicolas-Joseph Cugnot built the first steam-powered road vehicle in 1769, while the Swiss inventor François Isaac de Rivaz designed and constructed
3799-405: Is a fly-back system, using interruption of electrical primary system current through some type of synchronized interrupter. The interrupter can be either contact points or a power transistor. The problem with this type of ignition is that as RPM increases the availability of electrical energy decreases. This is especially a problem, since the amount of energy needed to ignite a more dense fuel mixture
3930-421: Is also why diesel and HCCI engines are more susceptible to cold-starting issues, although they run just as well in cold weather once started. Light duty diesel engines with indirect injection in automobiles and light trucks employ glowplugs (or other pre-heating: see Cummins ISB#6BT ) that pre-heat the combustion chamber just before starting to reduce no-start conditions in cold weather. Most diesels also have
4061-479: Is called " Fordism " and was copied by most major industries. The efficiency gains from the assembly line also coincided with the economic rise of the US. The assembly line forced workers to work at a certain pace with very repetitive motions which led to more output per worker while other countries were using less productive methods. In the automotive industry, its success was dominating, and quickly spread worldwide seeing
Vauxhall Light Six - Misplaced Pages Continue
4192-503: Is commonplace in CI engines, and has been occasionally used in SI engines. CI engines that use a blower typically use uniflow scavenging . In this design the cylinder wall contains several intake ports placed uniformly spaced along the circumference just above the position that the piston crown reaches when at BDC. An exhaust valve or several like that of 4-stroke engines is used. The final part of
4323-542: Is driven downward with power, it first uncovers the exhaust port where the burned fuel is expelled under high pressure and then the intake port where the process has been completed and will keep repeating. Later engines used a type of porting devised by the Deutz company to improve performance. It was called the Schnurle Reverse Flow system. DKW licensed this design for all their motorcycles. Their DKW RT 125
4454-448: Is expected to improve in future due to lower carbon electricity , and longer lasting batteries produced in larger factories. Many governments use fiscal policies, such as road tax , to discourage the purchase and use of more polluting cars; and many cities are doing the same with low-emission zones . Fuel taxes may act as an incentive for the production of more efficient, hence less polluting, car designs (e.g., hybrid vehicles ) and
4585-469: Is generally acknowledged as the inventor of the car. In 1879, Benz was granted a patent for his first engine, which had been designed in 1878. Many of his other inventions made the use of the internal combustion engine feasible for powering a vehicle. His first Motorwagen was built in 1885 in Mannheim , Germany. He was awarded the patent for its invention as of his application on 29 January 1886 (under
4716-415: Is held in place relative to the engine block by main bearings , which allow it to rotate. Bulkheads in the crankcase form a half of every main bearing; the other half is a detachable cap. In some cases a single main bearing deck is used rather than several smaller caps. A connecting rod is connected to offset sections of the crankshaft (the crankpins ) in one end and to the piston in the other end through
4847-406: Is higher. The result was often a high RPM misfire. Capacitor discharge ignition was developed. It produces a rising voltage that is sent to the spark plug. CD system voltages can reach 60,000 volts. CD ignitions use step-up transformers . The step-up transformer uses energy stored in a capacitance to generate electric spark . With either system, a mechanical or electrical control system provides
4978-445: Is not possible to dedicate a stroke exclusively for each of them. Starting at TDC the cycle consists of: While a 4-stroke engine uses the piston as a positive displacement pump to accomplish scavenging taking 2 of the 4 strokes, a 2-stroke engine uses the last part of the power stroke and the first part of the compression stroke for combined intake and exhaust. The work required to displace the charge and exhaust gases comes from either
5109-621: Is that cars can use lighter batteries. Most cars are designed to carry multiple occupants, often with four or five seats. Cars with five seats typically seat two passengers in the front and three in the rear. Full-size cars and large sport utility vehicles can often carry six, seven, or more occupants depending on the arrangement of the seats. On the other hand, sports cars are most often designed with only two seats. Utility vehicles like pickup trucks , combine seating with extra cargo or utility functionality. The differing needs for passenger capacity and their luggage or cargo space has resulted in
5240-514: Is the Wärtsilä-Sulzer RTA96-C turbocharged 2-stroke diesel, used in large container ships. It is the most efficient and powerful reciprocating internal combustion engine in the world with a thermal efficiency over 50%. For comparison, the most efficient small four-stroke engines are around 43% thermally-efficient (SAE 900648); size is an advantage for efficiency due to the increase in the ratio of volume to surface area. See
5371-826: Is the replacement of physical knobs and switches by secondary controls with touchscreen controls such as BMW 's iDrive and Ford 's MyFord Touch . Another change is that while early cars' pedals were physically linked to the brake mechanism and throttle, in the early 2020s, cars have increasingly replaced these physical linkages with electronic controls. Cars are typically equipped with interior lighting which can be toggled manually or be set to light up automatically with doors open, an entertainment system which originated from car radios , sideways windows which can be lowered or raised electrically (manually on earlier cars), and one or multiple auxiliary power outlets for supplying portable appliances such as mobile phones , portable fridges, power inverters , and electrical air pumps from
Vauxhall Light Six - Misplaced Pages Continue
5502-471: Is the usual formal term in British English . "Autocar", a variant likewise attested from 1895 and literally meaning " self-propelled car", is now considered archaic. " Horseless carriage " is attested from 1895. "Automobile", a classical compound derived from Ancient Greek autós ( αὐτός ) "self" and Latin mobilis "movable", entered English from French and was first adopted by
5633-593: The Automobile Club of Great Britain in 1897. It fell out of favour in Britain and is now used chiefly in North America , where the abbreviated form "auto" commonly appears as an adjective in compound formations like " auto industry " and " auto mechanic ". In 1649, Hans Hautsch of Nuremberg built a clockwork-driven carriage. The first steam-powered vehicle was designed by Ferdinand Verbiest ,
5764-639: The Great Depression , by 1940, only 17 of those were left. In Europe, much the same would happen. Morris set up its production line at Cowley in 1924, and soon outsold Ford, while beginning in 1923 to follow Ford's practice of vertical integration , buying Hotchkiss' British subsidiary (engines), Wrigley (gearboxes), and Osberton (radiators), for instance, as well as competitors, such as Wolseley : in 1925, Morris had 41 per cent of total British car production. Most British small-car assemblers, from Abbey to Xtra , had gone under. Citroën did
5895-611: The Otto engine , was created in 1876 by Nicolaus Otto . The term internal combustion engine usually refers to an engine in which combustion is intermittent , such as the more familiar two-stroke and four-stroke piston engines, along with variants, such as the six-stroke piston engine and the Wankel rotary engine . A second class of internal combustion engines use continuous combustion: gas turbines , jet engines and most rocket engines , each of which are internal combustion engines on
6026-679: The Portsmouth Block Mills , England, in 1802. The assembly line style of mass production and interchangeable parts had been pioneered in the US by Thomas Blanchard in 1821, at the Springfield Armory in Springfield, Massachusetts . This concept was greatly expanded by Henry Ford , beginning in 1913 with the world's first moving assembly line for cars at the Highland Park Ford Plant . As
6157-565: The Pyréolophore , which was granted a patent by Napoleon Bonaparte . This engine powered a boat on the Saône river in France. In the same year, Swiss engineer François Isaac de Rivaz invented a hydrogen-based internal combustion engine and powered the engine by electric spark. In 1808, De Rivaz fitted his invention to a primitive working vehicle – "the world's first internal combustion powered automobile". In 1823, Samuel Brown patented
6288-468: The Wankel engine has had more than very limited success. All in all, it is estimated that over 100,000 patents created the modern automobile and motorcycle. Large-scale, production-line manufacturing of affordable cars was started by Ransom Olds in 1901 at his Oldsmobile factory in Lansing, Michigan , and based upon stationary assembly line techniques pioneered by Marc Isambard Brunel at
6419-473: The external links for an in-cylinder combustion video in a 2-stroke, optically accessible motorcycle engine. Dugald Clerk developed the first two-cycle engine in 1879. It used a separate cylinder which functioned as a pump in order to transfer the fuel mixture to the cylinder. In 1899 John Day simplified Clerk's design into the type of 2 cycle engine that is very widely used today. Day cycle engines are crankcase scavenged and port timed. The crankcase and
6550-440: The tax opportunities. The ability of humans to move flexibly from place to place has far-reaching implications for the nature of societies. Cars are a major cause of urban air pollution , with all types of cars producing dust from brakes, tyres, and road wear , although these may be limited by vehicle emission standards . While there are different ways to power cars, most rely on petrol or diesel , and they consume almost
6681-756: The 1.8% annual average reduction between 2010 and 2015. Given slow progress to date, the IEA estimates fuel consumption will have to decrease by 4.3% per year on average from 2019 to 2030. The increase in sales of SUVs is bad for fuel economy. Many cities in Europe have banned older fossil fuel cars and all fossil fuel vehicles will be banned in Amsterdam from 2030. Many Chinese cities limit licensing of fossil fuel cars, and many countries plan to stop selling them between 2025 and 2050. Internal combustion engine An internal combustion engine ( ICE or IC engine )
SECTION 50
#17327795562836812-577: The 14hp ASX was sold for the same price and became by far the better seller. 1933 was also the first year all GM vehicles were installed with optional vent windows which were initially called “No Draft Individually Controlled Ventilation” later renamed "Ventiplanes" which the patent application was filed on Nov. 28, 1932. It was assigned to the Ternstedt Manufacturing Company, a GM subsidiary that manufactured components for Fisher Body . 23,294 cars were produced. The model
6943-487: The 1950s, Chevrolet shared bonnet, doors, roof, and windows with Pontiac ; by the 1990s, corporate powertrains and shared platforms (with interchangeable brakes , suspension, and other parts) were common. Even so, only major makers could afford high costs, and even companies with decades of production, such as Apperson , Cole , Dorris , Haynes , or Premier, could not manage: of some two hundred American car makers in existence in 1920, only 43 survived in 1930, and with
7074-812: The 20th and 21st centuries because there are more cars; the 1980s oil glut even fuelled the sales of low-economy vehicles in OECD countries. The BRIC countries are adding to this consumption. As of 2023 few production cars use wheel hub motors . In almost all hybrid (even mild hybrid ) and pure electric cars regenerative braking recovers and returns to a battery some energy which would otherwise be wasted by friction brakes getting hot. Although all cars must have friction brakes (front disc brakes and either disc or drum rear brakes ) for emergency stops, regenerative braking improves efficiency, particularly in city driving. Cars are equipped with controls used for driving, passenger comfort, and safety, normally operated by
7205-561: The Benz car to his line of products. Because France was more open to the early cars, initially more were built and sold in France through Roger than Benz sold in Germany. In August 1888, Bertha Benz , the wife and business partner of Carl Benz, undertook the first road trip by car, to prove the road-worthiness of her husband's invention. In 1896, Benz designed and patented the first internal-combustion flat engine , called boxermotor . During
7336-614: The US's first pedestrian car casualties in 1899 in New York City. There are now standard tests for safety in new cars, such as the Euro and US NCAP tests, and insurance-industry-backed tests by the Insurance Institute for Highway Safety (IIHS). However, not all such tests consider the safety of people outside the car, such as drivers of other cars, pedestrians and cyclists. The costs of car usage, which may include
7467-640: The US, where they replaced horse-drawn carriages . In Europe and other parts of the world, demand for automobiles did not increase until after World War II . In the 21st century, car usage is still increasing rapidly, especially in China, India, and other newly industrialised countries . Cars have controls for driving , parking , passenger comfort, and a variety of lamps . Over the decades, additional features and controls have been added to vehicles, making them progressively more complex. These include rear-reversing cameras , air conditioning , navigation systems , and in-car entertainment . Most cars in use in
7598-519: The United Kingdom, sentiment against them led to the Locomotive Acts of 1865. In 1807, Nicéphore Niépce and his brother Claude created what was probably the world's first internal combustion engine (which they called a Pyréolophore ), but installed it in a boat on the river Saone in France. Coincidentally, in 1807, the Swiss inventor François Isaac de Rivaz designed his own " de Rivaz internal combustion engine ", and used it to develop
7729-658: The United States. His patent was challenged by Henry Ford and others, and overturned in 1911. In 1893, the first running, petrol-driven American car was built and road-tested by the Duryea brothers of Springfield, Massachusetts . The first public run of the Duryea Motor Wagon took place on 21 September 1893, on Taylor Street in Metro Center Springfield. Studebaker , subsidiary of
7860-619: The Wankel design are used in some automobiles, aircraft and motorcycles. These are collectively known as internal-combustion-engine vehicles (ICEV). Where high power-to-weight ratios are required, internal combustion engines appear in the form of combustion turbines , or sometimes Wankel engines. Powered aircraft typically use an ICE which may be a reciprocating engine. Airplanes can instead use jet engines and helicopters can instead employ turboshafts ; both of which are types of turbines. In addition to providing propulsion, aircraft may employ
7991-489: The associated process. While an engine is in operation, the crankshaft rotates continuously at a nearly constant speed . In a 4-stroke ICE, each piston experiences 2 strokes per crankshaft revolution in the following order. Starting the description at TDC, these are: The defining characteristic of this kind of engine is that each piston completes a cycle every crankshaft revolution. The 4 processes of intake, compression, power and exhaust take place in only 2 strokes so that it
SECTION 60
#17327795562838122-412: The auspices of his major company, Benz & Cie. , which was founded in 1883). Benz began promotion of the vehicle on 3 July 1886, and about 25 Benz vehicles were sold between 1888 and 1893, when his first four-wheeler was introduced along with a cheaper model. They also were powered with four-stroke engines of his own design. Emile Roger of France, already producing Benz engines under license, now added
8253-462: The availability of a large variety of body styles to meet individual consumer requirements that include, among others, the sedan/saloon , hatchback , station wagon/estate , coupe , and minivan . Traffic collisions are the largest cause of injury-related deaths worldwide. Mary Ward became one of the first documented car fatalities in 1869 in Parsonstown , Ireland, and Henry Bliss one of
8384-564: The brand name Daimler . It was a horse-drawn stagecoach built by another manufacturer, which they retrofitted with an engine of their design. By 1895, about 30 vehicles had been built by Daimler and Maybach, either at the Daimler works or in the Hotel Hermann, where they set up shop after disputes with their backers. Benz, Maybach, and the Daimler team seem to have been unaware of each other's early work. They never worked together; by
8515-455: The car visible to other users, so that the vehicle can be used at night; in some jurisdictions, daytime running lights ; red brake lights to indicate when the brakes are applied; amber turn signal lights to indicate the turn intentions of the driver; white-coloured reverse lights to illuminate the area behind the car (and indicate that the driver will be or is reversing); and on some vehicles, additional lights (e.g., side marker lights) to increase
8646-619: The combustion gases to escape. The valves are often poppet valves but they can also be rotary valves or sleeve valves . However, 2-stroke crankcase scavenged engines connect the gas ports directly to the cylinder wall without poppet valves; the piston controls their opening and occlusion instead. The cylinder head also holds the spark plug in the case of spark ignition engines and the injector for engines that use direct injection. All CI (compression ignition) engines use fuel injection, usually direct injection but some engines instead use indirect injection . SI (spark ignition) engines can use
8777-455: The compressed air and combustion products and slide continuously within it while the engine is in operation. In smaller engines, the pistons are made of aluminum; while in larger applications, they are typically made of cast iron. In performance applications, pistons can also be titanium or forged steel for greater strength. The top surface of the piston is called its crown and is typically flat or concave. Some two-stroke engines use pistons with
8908-432: The compressed charge, four-cycle engine. In 1879, Karl Benz patented a reliable two-stroke gasoline engine. Later, in 1886, Benz began the first commercial production of motor vehicles with an internal combustion engine, in which a three-wheeled, four-cycle engine and chassis formed a single unit. In 1892, Rudolf Diesel developed the first compressed charge, compression ignition engine. In 1926, Robert Goddard launched
9039-410: The corresponding ports. The intake manifold connects to the air filter directly, or to a carburetor when one is present, which is then connected to the air filter . It distributes the air incoming from these devices to the individual cylinders. The exhaust manifold is the first component in the exhaust system . It collects the exhaust gases from the cylinders and drives it to the following component in
9170-443: The cost of: acquiring the vehicle, repairs and auto maintenance , fuel, depreciation , driving time, parking fees , taxes, and insurance, are weighed against the cost of the alternatives, and the value of the benefits—perceived and real—of vehicle usage. The benefits may include on-demand transportation, mobility, independence, and convenience, and emergency power . During the 1920s, cars had another benefit: "[c]ouples finally had
9301-400: The crankcase or a separate blower. For scavenging, expulsion of burned gas and entry of fresh mix, two main approaches are described: Loop scavenging, and Uniflow scavenging. SAE news published in the 2010s that 'Loop Scavenging' is better under any circumstance than Uniflow Scavenging. Some SI engines are crankcase scavenged and do not use poppet valves. Instead, the crankcase and the part of
9432-401: The crankcase pressure is slightly below intake pressure, to let it be filled with a new charge; this happens when the piston is moving upwards. When the piston is moving downwards the pressure in the crankcase increases and the reed valve closes promptly, then the charge in the crankcase is compressed. When the piston is moving downwards, it also uncovers the exhaust port and the transfer port and
9563-413: The crankcase to the port in the cylinder to provide for intake and another from the exhaust port to the exhaust pipe. The height of the port in relationship to the length of the cylinder is called the "port timing". On the first upstroke of the engine there would be no fuel inducted into the cylinder as the crankcase was empty. On the downstroke, the piston now compresses the fuel mix, which has lubricated
9694-431: The cylinder below the piston is used as a pump. The intake port is connected to the crankcase through a reed valve or a rotary disk valve driven by the engine. For each cylinder, a transfer port connects in one end to the crankcase and in the other end to the cylinder wall. The exhaust port is connected directly to the cylinder wall. The transfer and exhaust port are opened and closed by the piston. The reed valve opens when
9825-411: The cylinder block has fins protruding away from it to cool the engine by directly transferring heat to the air. The cylinder walls are usually finished by honing to obtain a cross hatch , which is able to retain more oil. A too rough surface would quickly harm the engine by excessive wear on the piston. The pistons are short cylindrical parts which seal one end of the cylinder from the high pressure of
9956-407: The cylinder. Because there is no obstruction in the cylinder of the fuel to move directly out of the exhaust port prior to the piston rising far enough to close the port, early engines used a high domed piston to slow down the flow of fuel. Later the fuel was "resonated" back into the cylinder using an expansion chamber design. When the piston rose close to TDC, a spark ignited the fuel. As the piston
10087-414: The cylinder. At low rpm, the spark is timed to occur close to the piston achieving top dead center. In order to produce more power, as rpm rises the spark is advanced sooner during piston movement. The spark occurs while the fuel is still being compressed progressively more as rpm rises. The necessary high voltage, typically 10,000 volts, is supplied by an induction coil or transformer. The induction coil
10218-588: The development of alternative fuels . High fuel taxes or cultural change may provide a strong incentive for consumers to purchase lighter, smaller, more fuel-efficient cars, or to not drive . The lifetime of a car built in the 2020s is expected to be about 16 years, or about 2 millionkm (1.2 millionmiles) if driven a lot. According to the International Energy Agency the average rated fuel consumption of new light-duty vehicles fell by only 0.9% between 2017 and 2019, far smaller than
10349-749: The driver from a crash perspective, but more dangerous for other vehicles and road users. The weight of a car influences fuel consumption and performance, with more weight resulting in increased fuel consumption and decreased performance. The Wuling Hongguang Mini EV , a typical city car , weighs about 700 kilograms (1,500 lb). Heavier cars include SUVs and extended-length SUVs like the Suburban . Cars have also become wider. Some places tax heavier cars more: as well as improving pedestrian safety this can encourage manufacturers to use materials such as recycled aluminium instead of steel. It has been suggested that one benefit of subsidising charging infrastructure
10480-567: The early 2020s are propelled by an internal combustion engine , fueled by the combustion of fossil fuels . Electric cars , which were invented early in the history of the car , became commercially available in the 2000s and are predicted to cost less to buy than petrol-driven cars before 2025. The transition from fossil fuel-powered cars to electric cars features prominently in most climate change mitigation scenarios , such as Project Drawdown 's 100 actionable solutions for climate change. There are costs and benefits to car use . The costs to
10611-413: The early engines which used Hot Tube ignition. When Bosch developed the magneto it became the primary system for producing electricity to energize a spark plug. Many small engines still use magneto ignition. Small engines are started by hand cranking using a recoil starter or hand crank. Prior to Charles F. Kettering of Delco's development of the automotive starter all gasoline engined automobiles used
10742-453: The efficiency is higher because more energy is extracted from the fuel than what could be extracted by the combustion engine alone. Combined cycle power plants achieve efficiencies in the range of 50–60%. In a smaller scale, stationary engines like gas engines or diesel generators are used for backup or for providing electrical power to areas not connected to an electric grid . Small engines (usually 2‐stroke gasoline/petrol engines) are
10873-412: The end of that year there were more than 16 million electric cars on the world's roads. Despite rapid growth, less than two per cent of cars on the world's roads were fully electric and plug-in hybrid cars by the end of 2021. Cars for racing or speed records have sometimes employed jet or rocket engines, but these are impractical for common use. Oil consumption has increased rapidly in
11004-543: The engine is off. The battery also supplies electrical power during rare run conditions where the alternator cannot maintain more than 13.8 volts (for a common 12 V automotive electrical system). As alternator voltage falls below 13.8 volts, the lead-acid storage battery increasingly picks up electrical load. During virtually all running conditions, including normal idle conditions, the alternator supplies primary electrical power. Some systems disable alternator field (rotor) power during wide-open throttle conditions. Disabling
11135-435: The field reduces alternator pulley mechanical loading to nearly zero, maximizing crankshaft power. In this case, the battery supplies all primary electrical power. Gasoline engines take in a mixture of air and gasoline and compress it by the movement of the piston from bottom dead center to top dead center when the fuel is at maximum compression. The reduction in the size of the swept area of the cylinder and taking into account
11266-671: The first internal combustion engine to be applied industrially. In 1854, in the UK, the Italian inventors Eugenio Barsanti and Felice Matteucci obtained the certification: "Obtaining Motive Power by the Explosion of Gases". In 1857 the Great Seal Patent Office conceded them patent No.1655 for the invention of an "Improved Apparatus for Obtaining Motive Power from Gases". Barsanti and Matteucci obtained other patents for
11397-543: The first internal combustion-powered automobile in 1808. The modern car—a practical, marketable automobile for everyday use—was invented in 1886, when the German inventor Carl Benz patented his Benz Patent-Motorwagen . Commercial cars became widely available during the 20th century. The 1901 Oldsmobile Curved Dash and the 1908 Ford Model T , both American cars, are widely considered the first mass-produced and mass-affordable cars, respectively. Cars were rapidly adopted in
11528-595: The first liquid-fueled rocket. In 1939, the Heinkel He 178 became the world's first jet aircraft . At one time, the word engine (via Old French , from Latin ingenium , "ability") meant any piece of machinery —a sense that persists in expressions such as siege engine . A "motor" (from Latin motor , "mover") is any machine that produces mechanical power . Traditionally, electric motors are not referred to as "engines"; however, combustion engines are often referred to as "motors". (An electric engine refers to
11659-569: The first petrol-driven car in the country in 1894, followed by Frederick William Lanchester in 1895, but these were both one-offs. The first production vehicles in Great Britain came from the Daimler Company , a company founded by Harry J. Lawson in 1896, after purchasing the right to use the name of the engines. Lawson's company made its first car in 1897, and they bore the name Daimler. In 1892, German engineer Rudolf Diesel
11790-556: The following conditions: The main advantage of 2-stroke engines of this type is mechanical simplicity and a higher power-to-weight ratio than their 4-stroke counterparts. Despite having twice as many power strokes per cycle, less than twice the power of a comparable 4-stroke engine is attainable in practice. In the US, 2-stroke engines were banned for road vehicles due to the pollution. Off-road only motorcycles are still often 2-stroke but are rarely road legal. However, many thousands of 2-stroke lawn maintenance engines are in use. Using
11921-425: The founding of Ford France and Ford Britain in 1911, Ford Denmark 1923, Ford Germany 1925; in 1921, Citroën was the first native European manufacturer to adopt the production method. Soon, companies had to have assembly lines, or risk going broke; by 1930, 250 companies which did not, had disappeared. Development of automotive technology was rapid, due in part to the hundreds of small manufacturers competing to gain
12052-517: The gudgeon pin and thus transfers the force and translates the reciprocating motion of the pistons to the circular motion of the crankshaft. The end of the connecting rod attached to the gudgeon pin is called its small end, and the other end, where it is connected to the crankshaft, the big end. The big end has a detachable half to allow assembly around the crankshaft. It is kept together to the connecting rod by removable bolts. The cylinder head has an intake manifold and an exhaust manifold attached to
12183-505: The high temperature and pressure created by the engine in its compression process. The compression level that occurs is usually twice or more than a gasoline engine. Diesel engines take in air only, and shortly before peak compression, spray a small quantity of diesel fuel into the cylinder via a fuel injector that allows the fuel to instantly ignite. HCCI type engines take in both air and fuel, but continue to rely on an unaided auto-combustion process, due to higher pressures and temperature. This
12314-416: The higher pressure of the charge in the crankcase makes it enter the cylinder through the transfer port, blowing the exhaust gases. Lubrication is accomplished by adding two-stroke oil to the fuel in small ratios. Petroil refers to the mix of gasoline with the aforesaid oil. This kind of 2-stroke engine has a lower efficiency than comparable 4-strokes engines and releases more polluting exhaust gases for
12445-451: The highest thermal efficiencies among internal combustion engines of any kind. Some diesel–electric locomotive engines operate on the 2-stroke cycle. The most powerful of them have a brake power of around 4.5 MW or 6,000 HP . The EMD SD90MAC class of locomotives are an example of such. The comparable class GE AC6000CW , whose prime mover has almost the same brake power, uses a 4-stroke engine. An example of this type of engine
12576-528: The idea of different makes of cars produced by one company, called the General Motors Companion Make Program , so that buyers could "move up" as their fortunes improved. Reflecting the rapid pace of change, makes shared parts with one another so larger production volume resulted in lower costs for each price range. For example, in the 1930s, LaSalles , sold by Cadillac , used cheaper mechanical parts made by Oldsmobile ; in
12707-403: The individual include acquiring the vehicle, interest payments (if the car is financed), repairs and maintenance , fuel, depreciation , driving time, parking fees, taxes, and insurance . The costs to society include maintaining roads, land-use , road congestion , air pollution , noise pollution , public health , and disposing of the vehicle at the end of its life . Traffic collisions are
12838-419: The intake manifold is an air sleeve that feeds the intake ports. The intake ports are placed at a horizontal angle to the cylinder wall (I.e: they are in plane of the piston crown) to give a swirl to the incoming charge to improve combustion. The largest reciprocating IC are low speed CI engines of this type; they are used for marine propulsion (see marine diesel engine ) or electric power generation and achieve
12969-429: The inventor of the diesel engine, Rudolf Diesel , was using peanut oil to run his engines. Renewable fuels are commonly blended with fossil fuels. Hydrogen , which is rarely used, can be obtained from either fossil fuels or renewable energy. Various scientists and engineers contributed to the development of internal combustion engines. In 1791, John Barber developed the gas turbine . In 1794 Thomas Mead patented
13100-476: The largest cause of injury-related deaths worldwide. Personal benefits include on-demand transportation, mobility, independence, and convenience. Societal benefits include economic benefits, such as job and wealth creation from the automotive industry , transportation provision, societal well-being from leisure and travel opportunities, and the generation of revenue from taxation. People's ability to move flexibly from place to place has far-reaching implications for
13231-637: The last years of the 19th century, Benz was the largest car company in the world with 572 units produced in 1899 and, because of its size, Benz & Cie., became a joint-stock company . The first motor car in central Europe and one of the first factory-made cars in the world, was produced by Czech company Nesselsdorfer Wagenbau (later renamed to Tatra ) in 1897, the Präsident automobil. Daimler and Maybach founded Daimler Motoren Gesellschaft (DMG) in Cannstatt in 1890, and sold their first car in 1892 under
13362-580: The location for the accelerator and brake, but this was not always the case. Controls are evolving in response to new technologies, for example, the electric car and the integration of mobile communications. Some of the original controls are no longer required. For example, all cars once had controls for the choke valve, clutch, ignition timing , and a crank instead of an electric starter . However, new controls have also been added to vehicles, making them more complex. These include air conditioning , navigation systems , and in-car entertainment . Another trend
13493-422: The longest trip by a petrol-driven vehicle when their self-designed and built Daimler powered Peugeot Type 3 completed 2,100 kilometres (1,300 mi) from Valentigney to Paris and Brest and back again. They were attached to the first Paris–Brest–Paris bicycle race, but finished six days after the winning cyclist, Charles Terront . The first design for an American car with a petrol internal combustion engine
13624-545: The market. In Japan, car production was very limited before World War II. Only a handful of companies were producing vehicles in limited numbers, and these were small, three-wheeled for commercial uses, like Daihatsu , or were the result of partnering with European companies, like Isuzu building the Wolseley A-9 in 1922. Mitsubishi was also partnered with Fiat and built the Mitsubishi Model A based on
13755-426: The nature of societies . The English word car is believed to originate from Latin carrus / carrum "wheeled vehicle" or (via Old North French ) Middle English carre "two-wheeled cart", both of which in turn derive from Gaulish karros " chariot ". It originally referred to any wheeled horse-drawn vehicle , such as a cart , carriage , or wagon . "Motor car", attested from 1895,
13886-407: The oil into the combustion chamber. A ventilation system drives the small amount of gas that escapes past the pistons during normal operation (the blow-by gases) out of the crankcase so that it does not accumulate contaminating the oil and creating corrosion. In two-stroke gasoline engines the crankcase is part of the air–fuel path and due to the continuous flow of it, two-stroke engines do not need
14017-404: The on-board electrical system. More costly upper-class and luxury cars are equipped with features earlier such as massage seats and collision avoidance systems . Dedicated automotive fuses and circuit breakers prevent damage from electrical overload . Cars are typically fitted with multiple types of lights. These include headlights , which are used to illuminate the way ahead and make
14148-402: The outer side of the cylinder, passages that contain cooling fluid are cast into the engine block whereas, in some heavy duty engines, the passages are the types of removable cylinder sleeves which can be replaceable. Water-cooled engines contain passages in the engine block where cooling fluid circulates (the water jacket ). Some small engines are air-cooled, and instead of having a water jacket
14279-460: The part of the cylinder below the exhaust port is used as a pump. The operation of the Day cycle engine begins when the crankshaft is turned so that the piston moves from BDC upward (toward the head) creating a vacuum in the crankcase/cylinder area. The carburetor then feeds the fuel mixture into the crankcase through a reed valve or a rotary disk valve (driven by the engine). There are cast in ducts from
14410-427: The path. The exhaust system of an ICE may also include a catalytic converter and muffler . The final section in the path of the exhaust gases is the tailpipe . The top dead center (TDC) of a piston is the position where it is nearest to the valves; bottom dead center (BDC) is the opposite position where it is furthest from them. A stroke is the movement of a piston from TDC to BDC or vice versa, together with
14541-412: The piston in the cylinder and the bearings due to the fuel mix having oil added to it. As the piston moves downward it first uncovers the exhaust, but on the first stroke there is no burnt fuel to exhaust. As the piston moves downward further, it uncovers the intake port which has a duct that runs to the crankcase. Since the fuel mix in the crankcase is under pressure, the mix moves through the duct and into
14672-409: The power wasting in overcoming friction , or to make the mechanism work at all. Also, the lubricant used can reduce excess heat and provide additional cooling to components. At the very least, an engine requires lubrication in the following parts: In 2-stroke crankcase scavenged engines, the interior of the crankcase, and therefore the crankshaft, connecting rod and bottom of the pistons are sprayed by
14803-403: The primary power supply for vehicles such as cars , aircraft and boats . ICEs are typically powered by hydrocarbon -based fuels like natural gas , gasoline , diesel fuel , or ethanol . Renewable fuels like biodiesel are used in compression ignition (CI) engines and bioethanol or ETBE (ethyl tert-butyl ether) produced from bioethanol in spark ignition (SI) engines. As early as 1900
14934-472: The same in France, coming to cars in 1919; between them and other cheap cars in reply such as Renault 's 10CV and Peugeot 's 5CV , they produced 550,000 cars in 1925, and Mors , Hurtu , and others could not compete. Germany's first mass-manufactured car, the Opel 4PS Laubfrosch (Tree Frog), came off the line at Rüsselsheim in 1924, soon making Opel the top car builder in Germany, with 37.5 per cent of
15065-452: The same invention in France, Belgium and Piedmont between 1857 and 1859. In 1860, Belgian engineer Jean Joseph Etienne Lenoir produced a gas-fired internal combustion engine. In 1864, Nicolaus Otto patented the first atmospheric gas engine. In 1872, American George Brayton invented the first commercial liquid-fueled internal combustion engine. In 1876, Nicolaus Otto began working with Gottlieb Daimler and Wilhelm Maybach , patented
15196-684: The same principle as previously described. ( Firearms are also a form of internal combustion engine, though of a type so specialized that they are commonly treated as a separate category, along with weaponry such as mortars and anti-aircraft cannons.) In contrast, in external combustion engines , such as steam or Stirling engines , energy is delivered to a working fluid not consisting of, mixed with, or contaminated by combustion products. Working fluids for external combustion engines include air, hot water, pressurized water or even boiler -heated liquid sodium . While there are many stationary applications, most ICEs are used in mobile applications and are
15327-409: The smaller engine produced 36bhp at 4000 rpm and the 1781 cc produced 43bhp at 3500 rpm. The power was transmitted to the rear axle via a single-plate clutch to a 4-speed gearbox, with “silent third” and synchromesh on 3rd & 4th gears. Twelve volt electrics were fitted. The Cadet chassis was shortened by 6 in (150 mm) and extra cross-members added. Semi-elliptic leaf spring suspension
15458-400: The stem of the valve or may act upon a rocker arm , again, either directly or through a pushrod . The crankcase is sealed at the bottom with a sump that collects the falling oil during normal operation to be cycled again. The cavity created between the cylinder block and the sump houses a crankshaft that converts the reciprocating motion of the pistons to rotational motion. The crankshaft
15589-405: The time of the merger of the two companies, Daimler and Maybach were no longer part of DMG. Daimler died in 1900 and later that year, Maybach designed an engine named Daimler-Mercedes that was placed in a specially ordered model built to specifications set by Emil Jellinek . This was a production of a small number of vehicles for Jellinek to race and market in his country. Two years later, in 1902,
15720-530: The visibility of the car. Interior lights on the ceiling of the car are usually fitted for the driver and passengers. Some vehicles also have a boot light and, more rarely, an engine compartment light. During the late 20th and early 21st century, cars increased in weight due to batteries, modern steel safety cages, anti-lock brakes, airbags, and "more-powerful—if more efficient—engines" and, as of 2019 , typically weigh between 1 and 3 tonnes (1.1 and 3.3 short tons; 0.98 and 2.95 long tons). Heavier cars are safer for
15851-423: The volume of the combustion chamber is described by a ratio. Early engines had compression ratios of 6 to 1. As compression ratios were increased, the efficiency of the engine increased as well. With early induction and ignition systems the compression ratios had to be kept low. With advances in fuel technology and combustion management, high-performance engines can run reliably at 12:1 ratio. With low octane fuel,
15982-482: The world's attention. Key developments included electric ignition and the electric self-starter (both by Charles Kettering , for the Cadillac Motor Company in 1910–1911), independent suspension , and four-wheel brakes. Since the 1920s, nearly all cars have been mass-produced to meet market needs, so marketing plans often have heavily influenced car design. It was Alfred P. Sloan who established
16113-645: The world's first vehicle to be powered by such an engine. The Niépces' Pyréolophore was fuelled by a mixture of Lycopodium powder (dried spores of the Lycopodium plant), finely crushed coal dust and resin that were mixed with oil, whereas de Rivaz used a mixture of hydrogen and oxygen . Neither design was successful, as was the case with others, such as Samuel Brown , Samuel Morey , and Etienne Lenoir , who each built vehicles (usually adapted carriages or carts) powered by internal combustion engines. In November 1881, French inventor Gustave Trouvé demonstrated
16244-549: The world, the oil was actually drained and heated overnight and returned to the engine for cold starts. In the early 1950s, the gasoline Gasifier unit was developed, where, on cold weather starts, raw gasoline was diverted to the unit where part of the fuel was burned causing the other part to become a hot vapor sent directly to the intake valve manifold. This unit was quite popular until electric engine block heaters became standard on gasoline engines sold in cold climates. For ignition, diesel, PPC and HCCI engines rely solely on
16375-407: Was developed in 1926. This is the source of Ford's apocryphal remark, "any color as long as it's black". In 1914, an assembly line worker could buy a Model T with four months' pay. Ford's complex safety procedures—especially assigning each worker to a specific location instead of allowing them to roam about—dramatically reduced the rate of injury. The combination of high wages and high efficiency
16506-470: Was fitted to front and rear axles. The factory standard bodies used many panels from the Cadet but the radiator was now sloped back slightly and the filler cap was under the bonnet. All the windows used "Triplex" toughened glass. The chassis was also supplied to external coachbuilders. The launch price for the standard saloon was GBP195 allowing Vauxhall to advertise a 12hp car for less than GBP200. Unusually,
16637-1429: Was formed from a conglomerate of six companies who banded together as Fuji Heavy Industries , as a result of having been broken up under keiretsu legislation. The transport sector is a major contributor to air pollution , noise pollution and climate change . Most cars in use in the early 2020s run on petrol burnt in an internal combustion engine (ICE). The International Organization of Motor Vehicle Manufacturers says that, in countries that mandate low sulphur motor spirit, petrol-fuelled cars built to late 2010s standards (such as Euro-6) emit very little local air pollution. Some cities ban older petrol-driven cars and some countries plan to ban sales in future. However, some environmental groups say this phase-out of fossil fuel vehicles must be brought forwards to limit climate change. Production of petrol-fuelled cars peaked in 2017. Other hydrocarbon fossil fuels also burnt by deflagration (rather than detonation ) in ICE cars include diesel , autogas , and CNG . Removal of fossil fuel subsidies , concerns about oil dependence , tightening environmental laws and restrictions on greenhouse gas emissions are propelling work on alternative power systems for cars. This includes hybrid vehicles , plug-in electric vehicles and hydrogen vehicles . Out of all cars sold in 2021, nine per cent were electric, and by
16768-414: Was granted a patent for a "New Rational Combustion Engine". In 1897, he built the first diesel engine . Steam-, electric-, and petrol-driven vehicles competed for a few decades, with petrol internal combustion engines achieving dominance in the 1910s. Although various pistonless rotary engine designs have attempted to compete with the conventional piston and crankshaft design, only Mazda 's version of
16899-427: Was made in 1877 by George Selden of Rochester, New York . Selden applied for a patent for a car in 1879, but the patent application expired because the vehicle was never built. After a delay of 16 years and a series of attachments to his application, on 5 November 1895, Selden was granted a US patent ( U.S. patent 549,160 ) for a two-stroke car engine, which hindered, more than encouraged , development of cars in
17030-405: Was one of the first motor vehicles to achieve over 100 mpg as a result. Internal combustion engines require ignition of the mixture, either by spark ignition (SI) or compression ignition (CI) . Before the invention of reliable electrical methods, hot tube and flame methods were used. Experimental engines with laser ignition have been built. The spark-ignition engine was a refinement of
17161-459: Was revised in 1935 and given new designations although they kept the same engines. The chassis was re-designed with Dubonnet type independent front suspension enabling the engine to be moved forwards. A revised version appeared in 1937 with a curved radiator grille and pressed-steel wheels replacing the wire-spoked ones. 20,026 of the earlier cars and 39,537 of the post 1937 version were produced. Automobile A car , or an automobile ,
#282717