An anti-lock braking system ( ABS ) is a safety anti- skid braking system used on aircraft and on land vehicles , such as cars , motorcycles , trucks , and buses . ABS operates by preventing the wheels from locking up during braking, thereby maintaining tractive contact with the road surface and allowing the driver to maintain more control over the vehicle.
135-499: The Dodge Avenger is a front-wheel drive , mid-sized sedan that was marketed by Dodge . The Avenger made its North American debut in 1994 for the 1995 model year as a coupe that was produced until 2000. The model name was reintroduced to the market as a four-door sedan in 2007 for the 2008 model year. The Dodge Avenger name was used on the South African market Hillman Avengers in 1975 and 1976. The 2014 model year marked
270-420: A Munich study, half a fleet of taxicabs was equipped with anti-lock brakes, while the other half had conventional brake systems. The crash rate was substantially the same for both types of cab, and Wilde concludes this was due to drivers of ABS-equipped cabs taking more risks, assuming that ABS would take care of them, while the non-ABS drivers drove more carefully since ABS would not be there to help in case of
405-543: A Royal Enfield Super Meteor motorcycle was used by the Road Research Laboratory to test the Maxaret anti-lock brake. The experiments demonstrated that anti-lock brakes can be of great value to motorcycles, for which skidding is involved in a high proportion of accidents. Stopping distances were reduced in most of the tests compared with locked wheel braking, particularly on slippery surfaces, in which
540-427: A flywheel and valve attached to a hydraulic line that feeds the brake cylinders. The flywheel is attached to a drum that runs at the same speed as the wheel. In normal braking, the drum and flywheel should spin at the same speed. However, when a wheel slows down, then the drum would do the same, leaving the flywheel spinning at a faster rate. This causes the valve to open, allowing a small amount of brake fluid to bypass
675-537: A pump , and a controller . The majority of problems with the valve system occur due to clogged valves. When a valve is clogged it is unable to open, close, or change position. An inoperable valve will prevent the system from modulating the valves and controlling pressure supplied to the brakes. There are many different variations and control algorithms for use in ABS. One of the simpler systems works as follows: Anti-lock braking systems use different schemes depending on
810-417: A transverse engine , rather than the conventional longitudinal engine arrangement generally found in rear-wheel-drive and four-wheel-drive vehicles. By far the most common layout for a front-wheel-drive car is with the engine and transmission at the front of the car, mounted transversely. Other layouts of front-wheel drive that have been occasionally produced are a front-engine mounted longitudinally,
945-638: A 2008 model year sedan to replace the Dodge Stratus, whose coupe version had replaced the original Avenger in 2001. Like its Dodge Journey stablemate, the Avenger's exterior was styled by Chrysler's Ryan Nagode . Ben S. Chang designed the interior. The Avenger was officially unveiled as a concept car at the Paris Motor Show on 28 September 2006. It was launched in Europe and marketed in
1080-562: A cheaper, and even more successful Trumpf Junior model, which sold over 100,000 in August 1939, and in the same year Citroën introduced the very successful Traction Avant models in France, over time selling them in the hundred thousands. Hupmobile made 2 experimental models with front-wheel drive in 1932 and 1934, but neither came into production In the late 1930s, the Cord 810/812 of
1215-411: A dangerous situation. The Insurance Institute for Highway Safety released a study in 2010 that found motorcycles with ABS 37% less likely to be involved in a fatal crash than models without ABS. On a motorcycle, an anti-lock brake system prevents the wheels of a motorcycle from locking during braking situations. Based on information from wheel speed sensors the ABS unit adjusts the pressure of
1350-422: A dedicated micro-controller . ABS is offered or comes standard on most road vehicles and is the foundation for electronic stability control systems, which are rapidly increasing in popularity due to the great reduction in the price of vehicle electronics over the years. Modern electronic stability control (ESC) systems are an evolution of the ABS concept. Here, a minimum of two additional sensors are added to help
1485-456: A flexibly located electronically controlled cooling fan. This configuration was pioneered by Dante Giacosa in the 1964 Autobianchi Primula and popularized with the Fiat 128 . Fiat promoted in its advertising that mechanical features consumed only 20% of the vehicle's volume and that Enzo Ferrari drove a 128 as his personal vehicle. The 1959 Mini used a substantially different arrangement with
SECTION 10
#17327825609581620-456: A front-wheel-drive system for motorising horse-drawn carts. In 1899 the inventor Henry Sutton designed and built one of Australia's first cars, called The Sutton Autocar. This car may have been the first front-wheel-drive car in the world. Henry's car was reported in the English press at the time and featured in the English magazine Autocar , after which the car was named. Two prototypes of
1755-674: A fully independent double wishbone suspension and variable-speed rack-and-pinion steering. Trims included the Highline base model (the V6 engine, among other options, were made standard in 2000) and the ES. A DOHC 16-valve 2.0 L I4 engine (140 hp (104 kW; 142 PS) and 130 lb⋅ft (176 N⋅m) of torque) is standard. A SOHC 24-valve 2.5 L V6 engine and an automatic transmission (155 hp (116 kW; 157 PS) and 160 lb⋅ft (217 N⋅m) of torque) are optional on
1890-441: A massive increase in grip and handling over all but the most expensive cars on the market. It initially used flexing rubber instead of needle rollers at the inboard universal joints of the driveshafts but later changed to needle rollers, and GKN designed constant-velocity joint at each outboard end of the drive shafts to allow for steering movement. The Mini revived the use of front-wheel drive which had been largely abandoned since
2025-433: A mid-engine layout and a rear-engine layout. Experiments with front-wheel-drive cars date to the early days of the automobile. The world's first self-propelled vehicle, Nicolas-Joseph Cugnot 's 1769/1770 "fardier à vapeur" , was a front-wheel-driven three-wheeled steam-tractor. It then took at least a century for the first experiments with mobile internal combustion engines to gain traction. Sometime between 1895 and 1898
2160-471: A more powerful transverse engine: accordingly, faster versions featured longitudinally mounted (north–south) engines. Despite these developments, however, by the end of the 1980s, almost all major European and Japanese manufacturers had converged around the Fiat-pioneered system of a transversely mounted engine with an "end-on" transmission with unequal length driveshafts. For example, Renault dropped
2295-442: A normal stop where the pedal pressure would usually be gradually increased. Some systems additionally monitor the rate at the accelerator was released, and/or the time between accelerator release and brake application) and the system automatically increases braking force where not enough pressure is applied. Hard or panic braking on bumpy surfaces, because of the bumps causing the speed of the wheel(s) to become erratic may also trigger
2430-613: A power driver's seat. The coupe did not achieve high sales numbers, so in 2000, the Avenger was discontinued. It was replaced by the Dodge Stratus coupe for the 2001 model year. This coupe utilized the third-generation Eclipse platform and architecture. Mitsubishi assembled it at the former Diamond Star plant. However, the Stratus sedan was engineered and built by Chrysler. The Dodge Avenger nameplate returned in February 2007 as
2565-509: A soft ride while the R/T versions included a firmer suspension, front and rear stabilizer bars, and 18-inch wheels. For the 2011 model year, the Avenger received its first significant overhaul since its 2008 reintroduction. Exterior changes include slightly revised sheet metal with a new crosshair grille displaying the new Dodge logo on the lower right corner of the grille, a sleeker bumper cut design, and standard LED combination taillights. Changes to
2700-576: A transverse-mounted engine behind the front axle. This design would continue for 3 decades in Germany. Buckminster Fuller adopted rear-engine, front-wheel drive for his three Dymaxion Car prototypes. Other German car producers followed: Stoewer offered a car with front-wheel drive in 1931, Adler in 1932 and Audi in 1933. Versions of the Adler Trumpf sold five-figure numbers from 1932 to 1938, totalling over 25,600 units. In 1934, Adler added
2835-758: A transversely installed engine was the Suzuki Suzulight , which was a small "city" car, called a kei car in Japanese. In 1955, the Polish producer FSO in Warsaw introduced the front-wheel-driven Syrena of its own design. In 1959 Austin Mini was launched by the British Motor Corporation , designed by Alec Issigonis as a response to the first oil crisis, the 1956 Suez Crisis , and
SECTION 20
#17327825609582970-473: A very slippery surface such as sheet ice or gravel, it is possible to lock multiple wheels at once, and this can defeat ABS (which relies on comparing all four wheels and detecting individual wheels skidding). The availability of ABS relieves most drivers from learning threshold braking. A June 1999 National Highway Traffic Safety Administration (NHTSA) study found that ABS increased stopping distances on loose gravel by an average of 27.2 percent. According to
3105-540: A water cooled 3.5 horsepower (2.6 kW) Aster engine. The engine was mounted on the front axle and so was rotated by the tiller steering. The name Victoria Combination described the lightweight, two-seater trailer commonly known as a Victoria, combined with the rear axle and drive mechanism from a motor tricycle that was placed in front to achieve front wheel drive. It also known as the Eureka . By 1899 Victoria Combinations were participating in motoring events such as
3240-476: Is also known as the CAB (Controller Anti-lock Brake). Typically ABS includes a central electronic control unit (ECU), four wheel speed sensors , and at least two hydraulic valves within the brake hydraulics . The ECU constantly monitors the rotational speed of each wheel; if it detects the wheel rotating significantly slower than the speed of the vehicle, a condition indicative of impending wheel lock, it actuates
3375-533: Is an automated system that uses the principles of threshold braking and cadence braking , techniques which were once practiced by skillful drivers before ABS was widespread. ABS operates at a much faster rate and more effectively than most drivers could manage. Although ABS generally offers improved vehicle control and decreases stopping distances on dry and some slippery surfaces, on loose gravel or snow-covered surfaces ABS may significantly increase braking distance , while still improving steering control. Since ABS
3510-491: Is near the centre of the car, making the main component of its moment of inertia relatively low). Another result of this design is a lengthened chassis. Except for Citroën, after the 1930s, front-wheel drive would largely be abandoned for the following twenty years. Save the interruption of World War II , Citroën built some 3 ⁄ 4 million Traction Avants through 1957; adding their cheap 2CV people's car in 1948, and introducing an equally front-wheel driven successor for
3645-420: Is realized through the movement of a spring-tensioned piston. When pressure should be released, a linear motor pulls back the plunger piston and opens up more space for the fluid. The system was used for example in the ABS I (1988) and ABS II (1993) of BMW. The ABS II differed in size and an electronically controlled friction clutch was mounted on the shaft instead of a plunger. Further displacement sensors record
3780-409: Is that in the case of the motorcycle the front wheel is much more important for stability than the rear wheel. If the front wheel locks up between 0.2-0.7s, it loses gyrostatic forces and the motorcycle starts to oscillate because of the increased influence of side forces operating on the wheel contact line. The motorcycle becomes unstable and falls. Piston Systems : The pressure release in this system
3915-452: Is the change of the dynamic wheel load during braking. Compared to cars, the wheel load changes are more drastic, which can lead to a wheel lift up and a fall over. This can be intensified by a soft suspension. Some systems are equipped with a rear-wheel lift-off mitigation functionality. When the indicators of a possible rear lift-off are detected, the system releases brake pressure on the front wheel to counter this behavior. Another difference
4050-475: The British Motor Corporation – moved over to the industry-standard solution for the Austin Maestro in 1983, and all its subsequent front-wheel-drive models. By reducing drivetrain weight and space needs, vehicles could be made smaller and more efficient without sacrificing acceleration. Integrating the powertrain with a transverse as opposed to a longitudinal layout, along with unibody construction and
4185-612: The Cadillac lineup) back to rear-wheel drive. There were relatively few rear-wheel-drive cars marketed in North America by the early 1990s; Chrysler 's car line-up was entirely front-wheel drive by 1990. GM followed suit in 1996 where its B-body line was phased out, where its sports cars (Camaro, Firebird, Corvette) were the only RWDs marketed; by the early 2000s, the Chevrolet Corvette and Cadillac Catera were
Dodge Avenger - Misplaced Pages Continue
4320-492: The Douvrin engines used in the larger Renaults (20, 21, 25 and 30) used this longitudinal "forward" layout. The Saab Saab 99 , launched in 1968, also used a longitudinal engine with a transmission underneath with helical gears. The 1966 Oldsmobile Toronado was the first U.S. front-wheel-drive car since the Cord 810 . It used a longitudinal engine placement for its V8, coupled with an unusual "split" transmission, which turned
4455-578: The Fiat 128 featured a transverse-mounted engine with unequal-length drive shafts and an innovative clutch release mechanism – an arrangement which Fiat had strategically tested on a previous production model, the Primula , from its less market-critical subsidiary, Autobianchi . Ready for production in 1964, the Primula featured a gear train offset from the differential and final drive with unequal length drive shafts . The layout enabled
4590-617: The Great Depression , by 1932 the Cord L-29 was discontinued, with just 4,400 sold. The 1929 Ruxton sold just 200 cars built that year. The first successful consumer application came in 1929. The BSA (Birmingham Small Arms Company) produced the unique front-wheel-drive BSA three-wheeler. Production continued until 1936 during which time sports and touring models were available. In 1931 the DKW F1 from Germany made its debut, with
4725-626: The Infineon Raceway . In 2008, the Dodge CoT appearance was changed back to the Charger model. Rebadged models, mostly from Japanese or Korean manufacturers – Rebadged Chrysler/Plymouth models for external markets Front-wheel drive Front-wheel drive ( FWD ) is a form of engine and transmission layout used in motor vehicles, in which the engine drives the front wheels only. Most modern front-wheel-drive vehicles feature
4860-547: The Plymouth Cricket between 1972 and 1974. In place of the Hillman engines, this version used a Peugeot 1.6 L engine (as also installed in locally assembled Peugeot 404s ) to satisfy local content requirements. The Dodge-branded Avenger was introduced in 1975 and was then renamed Chrysler in 1976. This generation has nothing in common with later Dodge Avengers. After Chrysler ZA was merged into Sigma in 1976,
4995-620: The Prince Motor Company also developed a transmission-in-sump type layout for its first front wheel drive model, which after the company's takeover by Nissan , emerged as the Datsun 100A (Cherry) in 1971. In 1960 Lancia could evolve the project CemsaF11 of Antonio Fessia with the innovative Lancia Flavia for first time with motor Boxer on auxiliary frame for low centre of gravity. This scheme continued in Lancia until 1984 with
5130-458: The Taunus P4 . The 1965 Triumph 1300 was designed for a longitudinal engine with the transmission underneath. Audi has also used a longitudinally mounted engine overhung over the front wheels since the 1970s. Audi is one of the few manufacturers which still uses this particular configuration. It allows the use of equal-length half shafts and the easy addition of all-wheel drive , but has
5265-839: The Tracta constant-velocity joint in 1926. In October 1928 a sensation at the 22nd Paris Motor Show was the Bucciali TAV-6. Six years before the appearance of the Citroën Traction Avant and more than two years before the launch of the DKW F1, the Bucciali TAV-6 featured front-wheel drive. Both German makers DKW in 1931 and Adler in 1933 bought Tracta licenses for their first front-wheel-drive cars. Imperia in Belgium and Rosengart in France manufactured
5400-587: The "Top Safety Pick+" award in 2013. The discontinuation of the Dodge Avenger was announced by the automaker in early 2014, along with the end of the Chrysler 200 convertible model. The final 2014 model year Avengers were produced during the first quarter 2014. The Avenger nameplate has since been revived as the Jeep Avenger with the 2023 model year. The first-generation Dodge Avenger body style
5535-443: The 1930s. The transversely mounted engine combined with front-wheel drive was popularized by the 1959 Mini ; there the transmission was built into the sump of the engine, and drive was transferred to it via a set of primary gears . Another variant transmission concept was used by Simca in the 1960s keeping the engine and transmission in line, but transverse mounted and with unequal length driveshafts. This has proven itself to be
Dodge Avenger - Misplaced Pages Continue
5670-596: The 1948 Saab 92 . In 1946, English car company Lloyd cars produced the Lloyd 650 , a front-wheel-drive roadster. The two-stroke, two-cylinder motor was mounted transversely in the front and connected to the front wheels through a four-speed synchronised gearbox. The high price and lacklustre performance doomed its production. Only 600 units were produced from 1946 to 1950. In 1946 in Italy, Antonio Fessia created his Cemsa Caproni F11 , with 7 examples produced. His innovation
5805-420: The 1986 Ford Taurus . By the mid-1980s, most formerly rear-wheel-drive Japanese models were front-wheel drive, and by the mid-1990s, most American brands only sold a handful of rear-wheel-drive models. The vast majority of front-wheel-drive vehicles today use a transversely mounted engine with "end-on" mounted transmission, driving the front wheels via driveshafts linked via constant velocity (CV) joints , and
5940-418: The 2.0 L naturally aspirated World Engine, as well as a 2.0 L turbocharged diesel ( Pumpe-Düse ) made by Volkswagen . Although a 2008 model, the Dodge Avenger was available in February 2007. In the U.S. market, the Avenger was launched with a 30-second television advertisement, "Tuned Up", that debuted on 4 March 2007, during NHL hockey, an ad in which a lab technician discovers he can play " Smoke on
6075-502: The 2011 Avenger came standard with the existing 173 hp (129 kW) 2.4 L GEMA I4. However, it was now paired with a six-speed automatic or the option of having the previous four-speed. Also available was the new 3.6 L Pentastar V6, rated at 283 hp (211 kW) and 260 lb⋅ft (350 N⋅m) of torque. The suspension was revised to improve handling and ride quality. Trim level designations were replaced by Express, Mainstreet, Lux, and Heat models. The Dodge Avenger
6210-551: The 371 km (231 mi) Paris– St Malo race, finishing 23rd overall and second(last) in the class. In October a Victoria Combination won its class in the Paris-Rambouillet-Paris event, covering the 100-kilometre course at 26 km/h (16 mph). In 1900 it completed 240 kilometres (150 mi) non-stop at 29 km/h (18 mph). When production ceased in mid-1901, over 400 units had been sold for 3,000 Francs (circa $ 600) each. A different concept
6345-469: The ABS controller can detect the situation and take suitable action so that traction is regained. More sophisticated versions of this can also control throttle levels and brakes simultaneously. The speed sensors of ABS are sometimes used in indirect tire pressure monitoring system (TPMS), which can detect under-inflation of the tire(s) by the difference in the rotational speed of wheels. There are four main components of ABS: wheel speed sensors , valves ,
6480-419: The ABS, sometimes causing the system to enter its ice mode, where the system severely limits maximum available braking power. Nevertheless, ABS significantly improves safety and control for drivers in most on-road situations. Anti-lock brakes are the subject of some experiments centred around risk compensation theory, which asserts that drivers adapt to the safety benefit of ABS by driving more aggressively. In
6615-575: The Adler under the licenses using the Tracta CV joints. During the second World War, all British vehicles, U.S. Jeeps made by Ford and Dodge command cars used Tracta CV joints. Russia and Germany also used the Tracta CV joints, but without the licensing. The United States only saw a few limited production experiments like the Cord L-29 of 1929, the first American front-wheel-drive car to be offered to
6750-495: The Austrian brothers and bicycle producers Franz, Heinrich and Karl Gräf (see Gräf & Stift ) commissioned the technician Josef Kainz to build a voiturette with a one-cylinder De Dion-Bouton engine fitted in the front of the vehicle, powering the front axle . It is possibly the world's first front-wheel-drive automobile, but it never saw series production, with just one prototype made. In 1898, Latil , in France, devised
6885-673: The Autocar were built and the Austral Otis Company was going to go into business with Henry to manufacture Henry's car but the cost of the car was too prohibitive as it could not compete with the cost of imported cars. In 1898–99, the French manufacturer Société Parisienne patented their front-wheel-drive articulated vehicle concept which they manufactured as a Victoria Combination . It was variously powered by 1.75 or 2.5 horsepower (1.30 or 1.86 kW) De Dion-Bouton engine or
SECTION 50
#17327825609587020-512: The Avenger was soon canceled to allow Sigma to free up more production capacity for the Mazda 323 . The Avenger nameplate returned as a 2023 subcompact Jeep model available as a plug-in hybrid version or an all-electric drivetrain. Introduced as a two-door coupe in North America, the Dodge Avenger was built from 1994 until 2000 in a similar size and price class as the Dodge Daytona , which
7155-578: The Dutch Fokker F27 Friendship (which unusually had a Dunlop high pressure (200 Bar) pneumatic system in lieu of hydraulics for braking, nose wheel steering and landing gear retraction), being fitted with Maxaret as standard. Maxaret, while reducing braking distances by up to 30% in icy or wet conditions, also increased tire life, and had the additional advantage of allowing take-offs and landings in conditions that would preclude flying at all in non-Maxaret equipped aircraft. In 1958,
7290-509: The ES. Fog lamps and ABS are optional on the ES. Standard were 16-inch wheels, and the license plate was moved from the decklid to the rear bumper. The front and rear fasciae were redesigned. A Sport model was introduced (in addition to the base and ES). The Avenger Sport package consisted of exclusive 16-inch aluminum wheels and a body-color spoiler. This appearance package was available on the base model. A body-color rear spoiler, P215/50HR17 tires, and 17-inch cast-aluminum wheels were added for
7425-452: The ES. The V6 is also standard for the ES, and rear disc brakes. An onboard recycling vapor recovery system, Cafe Latte exterior color, and a black and gray interior color combination are added. Next-generation driver and front passenger airbags are added, as well as a new exterior color: Shark Blue. The V6 engine and automatic transmission are standard on all models in mid-year, as well as several options. An antilock braking system (ABS)
7560-742: The Honda brand. However, the Norwegian tax system made the well-equipped car very expensive, and the sales suffered from high costs. From 1984 the ALB-system, as well as the other optional features from Honda, was no longer a standard feature in Norway. In 1985 the Ford Scorpio was introduced to the European market with a Teves electronic system throughout the range as standard. For this the model
7695-579: The Mitsubishi GS as a starting point. The SE and SXT trim levels' base engine was the 2.4 L GEMA I4 naturally aspirated "World Engine", a joint venture between DaimlerChrysler, Mitsubishi, and Hyundai . Additional engines included an optional 2.7 L V6 in the SXT and a standard 3.5 L V6 in the R/T trim level. In addition to the 2.4 L World Engine and the V6s, export vehicles were offered with
7830-458: The NHTSA, "ABS works with your regular braking system by automatically pumping them. In vehicles not equipped with ABS, the driver has to manually pump the brakes to prevent wheel lockup. In vehicles equipped with ABS, your foot should remain firmly planted on the brake pedal, while ABS pumps the brakes for you so you can concentrate on steering to safety." When activated, some earlier ABSes caused
7965-891: The Sydney motoring industry and invented a system that used a "spherical radial gear" that was fitted to what is believed to have been a Standard (built by the Standard Motor Company of England). A photo of the car with the system fitted is available from the Mitchell Library and the patent design drawing is still available from the Australian Patent Office. reference; "Gilltraps Australian Cars from 1879 – A history of cars built in Australia" (authors Gilltrap T and M) ISBN 0 85558 936 1 (Golden Press Pty Ltd) The next application of front-wheel drive
8100-520: The TA, the DS model, in 1955. Front-wheel drive continued with the 1948 Citroën 2CV , where the air-cooled lightweight aluminium flat twin engine was mounted ahead of the front wheels, but used Hooke type universal joint driveshaft joints, and 1955 Citroën DS , featuring the mid-engine layout. Panhard of France, DKW of Germany and Saab of Sweden offered exclusively front-wheel-drive cars, starting with
8235-635: The United Kingdom, filling a gap in the Chrysler range left by the Neon's discontinuation four years earlier. It was also launched in Australia with only the 2.4 L engine. The Avenger was discontinued in that market in 2010 due to slow sales. The 2007 through 2014 models were sold in New Zealand. According to some reports, the Avenger and the redesigned Chrysler Sebring share a DaimlerChrysler / Mitsubishi Motors platform called JS, which used
SECTION 60
#17327825609588370-506: The United Kingdom. Sales of the Avenger continued in the Republic of Ireland and Western Europe until late 2009, following Fiat's takeover of Chrysler Group. This version continued with SE and SXT trim levels but was not badged the same way as North American or South American versions. Under the influence of Fiat, the 2010 model year Avenger sedan had few changes.New were front side and head-curtain airbags as well as head-impact protection in
8505-612: The United States managed a bit better than its predecessor one decade earlier. These vehicles featured a layout that places the engine behind the transmission, running "backwards," (save for the Cord, which drove the transmission from the front of the engine). The basic front-wheel-drive layout provides sharp turning, and better weight distribution creates "positive handling characteristics" due to its low polar inertia and relatively favourable weight distribution. (The heaviest component
8640-557: The United States, and even competed in the 1906 Vanderbilt Cup and the French Grand Prix . In 1912 he began manufacturing a line of wheeled fire engine tractors which used his front-wheel-drive system, but due to lack of sales this venture failed. In Australia in 1915 G.J. Hoskins designed and was granted a patent for his front-wheel-drive system. Based in Burwood NSW Mr Hoskins was a prominent member of
8775-509: The Water " by Deep Purple on the Avenger's transmission. Another television spot likened the Avenger to the "superhero" vehicle for the everyman, depicting a driver piloting his Avenger through Gotham-like streets and alleys, speaking to the MyGig entertainment system in distinctly Batman -reminiscent tones, to arrive home, pull into a two-car garage, and open the rear door to a sleeping child in
8910-403: The benefit of ABS. In real-world conditions, even an alert and experienced driver without ABS would find it difficult to match or improve on the performance of a typical driver with a modern ABS-equipped vehicle. ABS reduces the chances of crashing, and/or the severity of impact. The recommended technique for non-expert drivers in an ABS-equipped car, in a typical full-braking emergency, is to press
9045-429: The boom in bubble cars that followed. It was the first production front-wheel-drive car with a watercooled inline four-cylinder engine mounted transversely. This allowed eighty percent of the floor plan for the use of passengers and luggage. The majority of modern cars use this configuration. Its progressive rate rubber sprung independent suspension, low centre of gravity, and wheel at each corner with radial tyres, gave
9180-557: The brake fluid in order to keep traction during deceleration to avoid accidents. Motorcycle ABS helps the rider to maintain stability during braking and to decrease the stopping distance. It provides traction even on low friction surfaces. While older ABS models are derived from cars, recent Motorcycle ABS is the result of research, oriented to the specifics of motorcycles in case of size, weight, and functionality. National and international organizations have evaluated Motorcycle ABS to be an important factor in increasing safety and reducing
9315-432: The brake pedal as firmly as possible and, where appropriate, to steer around obstructions. In such situations, ABS will significantly reduce the chances of a skid and subsequent loss of control. In gravel, sand, and deep snow, ABS tends to increase braking distances. On these surfaces, locked wheels dig in and stop the vehicle more quickly. ABS prevents this from occurring. Some ABS calibrations reduce this problem by slowing
9450-423: The brake pedal to pulse noticeably. As most drivers rarely or do not brake hard enough to cause brake lock-up, and drivers typically do not read the vehicle's owner's manual, this may not be noticeable until an emergency. Some manufacturers have therefore implemented a brake assist system that determines that the driver is attempting a "panic stop" (by detecting that the brake pedal was depressed very quickly, unlike
9585-439: The center of the curve turn slower than the outer two. For this same reason, a differential is used in virtually all roadgoing vehicles. If a fault develops in any part of the ABS, a warning light will usually be illuminated on the vehicle instrument panel, and the ABS will be disabled until the fault is rectified. Modern ABS applies individual brake pressure to all four wheels through a control system of hub-mounted sensors and
9720-434: The cycling time, thus letting the wheels repeatedly briefly lock and unlock. Some vehicle manufacturers provide an "off-road" button to turn the ABS function off. The primary benefit of ABS on such surfaces is to increase the ability of the driver to maintain control of the car rather than go into a skid, though the loss of control remains more likely on soft surfaces such as gravel or on slippery surfaces such as snow or ice. On
9855-448: The deceleration of one wheel exceeds a fixed threshold and 2) whether the brake slip, calculated based on information of both wheels, rises above a certain percentage and enters an unstable zone. These are indicators for a high possibility of a locking wheel. To countermeasure these irregularities the ECU signals the hydraulic unit to hold or to release pressure. After signals show the return to
9990-467: The development of the anti-locking braking system on commercial vehicles to prevent locking on slippery roads, followed in 1986 by the electronic braking system (EBS) for heavy-duty vehicles. 1978: Mercedes-Benz W116 As one of the firsts, used an electronic four-wheel multi-channel anti-lock braking system (ABS) from Bosch as an option from 1978 on. 1982: Honda introduced electronically controlled multi-channel ALB (Anti Locking Brakes) as an option for
10125-442: The disadvantage that it makes it difficult to achieve 50/50 weight distribution (although they remedy this in four-wheel-drive models by mounting the gearbox at the rear of the transaxle ). The Subaru 1000 appeared in 1966 using front-wheel drive mated to a flat-4 engine, with the driveshafts of equal length extending from the transmission, which addressed some of the issues of the powertrain being somewhat complex and unbalanced in
10260-404: The driver intends. The steering wheel sensor also helps in the operation of Cornering Brake Control (CBC), since this will tell the ABS that wheels on the inside of the curve should brake more than wheels on the outside, and by how much. ABS equipment may also be used to implement a traction control system (TCS) on the acceleration of the vehicle. If, when accelerating, the tire loses traction,
10395-415: The driver via brake pedal pulsation. Some anti-lock systems can apply or release braking pressure 15 times per second. Because of this, the wheels of cars equipped with ABS are practically impossible to lock even during panic braking in extreme conditions. The ECU is programmed to disregard differences in wheel rotative speed below a critical threshold because when the car is turning, the two wheels towards
10530-529: The end of Avenger production as the mid-sized models for both the Dodge and Chrysler brands were consolidated into the new Chrysler 200 introduced for the 2015 model year while Dodge received the new compact Dart . The first use of the Dodge Avenger name was on a badge-engineered version of the European Hillman Avenger , exclusive to South Africa . The same car was sold in North America as
10665-557: The end production of Lancia Gamma and successfully cloned until today by Subaru . Lancia, however also made front-wheel drive its flagship even in sport cars as the winner of the Rally, Lancia Fulvia , and then with large-scale models with excellent road qualities and performances including Lancia Beta , Lancia Delta , Lancia Thema including the powerful Lancia Thema 8.32 with engine Ferrari and all subsequent models. Ford introduced front-wheel drive to its European customers in 1962 with
10800-439: The engine and gearbox to be located side by side without sharing lubricating fluid while orienting the cooling fan toward fresh air flow. By using the Primula as a test-bed, Fiat was able to sufficiently resolve the layout's disadvantages, including uneven side-to-side power transmission, uneven tire wear and potential torque steer , the tendency for the power of the engine alone to steer the car under heavy acceleration. The problem
10935-807: The engine compartment – the Alfa Romeo Alfasud (and its replacement, the 1983 Alfa 33 as well as the Alfa 145/146 up to the late 1990s) also used the same layout. Honda also introduced several small front-wheel drive vehicles, with the N360 and N600 , the Z360 and Z600 in 1967, the Honda 1300 in 1969, followed by the Honda Civic in 1972 and the Honda Accord in 1976. Also in the 1970s and 1980s,
11070-412: The engine driving the front wheels through an offset final drive and unequal-length driveshafts, combined with MacPherson struts and an independently located radiator – subsequently became common with competitors and arguably an industry standard. The Corporate Average Fuel Economy standard drove a mass changeover of cars in the U.S. to front-wheel drive. The change began in 1978, with
11205-517: The engine power 180 degrees. Power then went to a differential mounted to the transmission case, from which half-shafts took it to the wheels. The driveline was set fairly at centre-point of the wheels for better weight distribution, though this raised the engine, requiring lowered intake systems. Little known outside of Italy, the Primula is today primarily known for innovating the modern economy-car layout. – Hemmings Motor News , August 2011 Front-wheel-drive layout had been highly impacted by
11340-533: The engine. The layout often required the engine be removed to service the clutch. This Active Tourer MPV wants to be more stable than a BMW M3, and using the Dante Giacosa-pattern front-wheel-drive layout compacts the mechanicals and saves space for people in the reduced overall length of what will surely become a production 1-series tall-sedan crossover. – Robert Cumberford , Automobile Magazine , March 2013 As engineered by Dante Giacosa ,
11475-586: The first motorcycle with an electro-hydraulic ABS: the BMW K100 . Yamaha Introduced the FJ1200 model with optional ABS in 1991. Honda followed suit in 1992 with the launch of its first motorcycle ABS on the ST1100 Pan European. In 2007, Suzuki launched its GSF1200SA (Bandit) with an ABS. In 2005, Harley-Davidson began offering an ABS option on police bikes. The anti-lock brake controller
11610-670: The first four-wheel vehicle ABS for series production. Motorcycles of BMW K100 series were optionally equipped with the ABS, which added 11 kg to the bike. It was developed together with FAG Kugelfischer and regulated the pressure in the braking circuits via a plunger piston . Japanese manufacturers followed with an ABS option by 1992 on the Honda ST1100 and the Yamaha FJ1200 . Continental presented its first Motorcycle Integral ABS (MIB) in 2006. It has been developed in cooperation with BMW and weighed 2.3 kg. While
11745-419: The first generation of motorcycle ABS weighed around 11 kg, the generation (2011) presented by Bosch in 2009 weighs 0.7 kg (ABS base) and 1.6 kg (ABS enhanced) with integral braking. Wheel speed sensors mounted on the front and rear wheel constantly measures the rotational speed of each wheel and delivers this information to an Electronic Control Unit (ECU). The ECU detects two things: 1) if
11880-402: The front axles of almost every four-wheel or all-wheel drive vehicle. Neither automobile was particularly successful in the open market. In spite of the Cord's hallmark innovation, using CV joints, and being competitively priced against contemporaneous alternatives, the buyers demographic were expecting more than the car's 80 mph (130 km/h) top speed, and combined with the effect of
12015-466: The front seats. The optional all-wheel drive was discontinued, limiting the Avenger to only front-wheel drive. The 2.7 L V6 was dropped, leaving two different drivetrains: a 2.4 L (173 hp (129 kW; 175 PS) I4 with four-speed automatic transmission (the SXT model) or a 3.5 L (235 hp (175 kW; 238 PS) V6 with AutoStick six-speed (available on the R/T). The Avenger featured
12150-469: The higher-priced American cars such as the Mercury Milan , Pontiac G6 , and Saturn Aura . For the 2009 model year, like its Caliber , Charger , Grand Caravan , Journey , and Nitro models, the "AVENGER" badge at the trunk lid's left was repositioned to the right side to make way for "DODGE" at the left. Following Fiat's takeover of Chrysler Group, marketing of the Avenger was discontinued in
12285-606: The improvement could be as much as 30%. Enfield's technical director at the time, Tony Wilson-Jones, saw little future in the system, however, and it was not put into production by the company. A fully-mechanical system saw limited automobile use in the 1960s in the Ferguson P99 racing car, the Jensen FF , and the experimental all-wheel drive Ford Zodiac , but saw no further use; the system proved expensive and unreliable. The first fully-electronic anti-lock braking system
12420-493: The interior are more noticeable with a completely redesigned dashboard and instrument panel featuring an available 6.5-inch navigation/media center screen. Higher-quality soft-touch plastics for dashboard, door, and trim panels replaced the old materials, which were criticized for their poor fit and finish quality, as well as being unpleasant to the touch. The seats receive better cushioning and higher-grade upholstery. Two-tone interior color combinations were available. Mechanically,
12555-493: The introduction of the first American-built transverse-engined cars, the Plymouth Horizon and Dodge Omni (based on the European designed Simca Horizon ), followed by the 1980 Chevrolet Citation and numerous other vehicles. Meanwhile, European car makers, that had moved to front-wheel drive decades before, began to homogenize their engine arrangement only in this decade, leaving Saab , Audi (and Volkswagen ) as
12690-404: The master cylinder into a local reservoir, lowering the pressure on the cylinder and releasing the brakes. The use of the drum and flywheel meant the valve only opened when the wheel was turning. In testing, a 30% improvement in braking performance was noted, because the pilots immediately applied full brakes instead of slowly increasing pressure in order to find the skid point. An additional benefit
12825-527: The model on which almost all modern FWD vehicles are now based. Peugeot and Renault on their jointly developed small car engine of the 1970s where the 4-cylinder block was canted over to reduce the overall height of the engine with the transmission mounted on the side of the crankcase in what became popularly known as the "suitcase" arrangement ( PSA X engine ). The tendency of this layout to generate unwanted transmission "whine" has seen it fall out of favour. Also, clutch changes required engine removal. In Japan,
12960-429: The modern systems that were introduced in the 1950s. In 1908, for example, J.E. Francis introduced his 'Slip Prevention Regulator for Rail Vehicles'. In 1920 the French automobile and aircraft pioneer Gabriel Voisin experimented with systems that modulated the hydraulic braking pressure on his aircraft brakes to reduce the risk of tire slippage, as threshold braking on aircraft is nearly impossible. These systems used
13095-511: The number and severity of motorcycle crashes and collisions. The European Commission passed legislation in 2012 that made the fitment with ABS for all new motorcycles above 125cc to be mandatory from 1 January 2016. Consumer Reports said in 2016 that "ABS is commonly offered on large, expensive models, but it has been spreading to several entry-level sportbikes and midsized bikes". In 1988, BMW introduced an electronic/ hydraulic ABS for motorcycles, ten years after Daimler Benz and Bosch released
13230-634: The only RWD cars offered by General Motors until the introduction of the Sigma platform . After the phaseout of the Ford Panther platform (except for the Mustang), Ford automobiles (including the Transit Connect van) manufactured for the 2012 model year to present are front-wheel drive; its D3 platform (based on a Volvo platform) has optional all-wheel drive. Antilock braking system ABS
13365-551: The only manufacturers offering a front-drive longitudinal engine layout. Years before this was the most common layout in Europe, with examples like Citroën DS , Renault 12 , Renault 5 , Renault 25 (a Chrysler LH ancestor) Alfa Romeo 33 , Volkswagen Passat , etc. This transition can be exemplified in the Renault 21 that was offered with disparate engine configurations. The 1.7-litre version featured an "east–west" (transversely) mounted engine, but Renault had no gearbox suitable for
13500-1085: The option the True-Track Braking System on the Oldsmobile Toronado . In 1972, the option was made available in all Cadillacs. In 1971, Nissan offered an EAL (Electro Anti-lock System) developed by Japanese company Denso as an option on the Nissan President , which became Japan 's first electronic ABS. 1971: The Imperial became the first production car with a 4 wheel computer-operated anti-lock braking system. Toyota introduced electronically controlled anti-skid brakes on Toyota Crown labeled as ESC (Electronic Skid Control). 1971: First truck application: "Antislittamento" system developed by Fiat Veicoli Industriali and installed on Fiat truck model 691N1. 1972: four-wheel-drive Triumph 2500 Estates were fitted with Mullard electronic systems as standard. Such cars were rare however and very few remain. 1976: WABCO began
13635-963: The pre-war DKW F8 and F9 reappeared as the IFA F8 and IFA F9 in 1949, followed by the AWZ P70 in 1955, the Wartburg 311 in 1956 and the Trabant in 1958, all with front-wheel drive. The P70 and Trabant had Duroplast bodies, and the Trabant had both a monocoque body and a transversely mounted engine, a modern design in some ways. In 1950 West German makers also reintroduced front-wheel-drive cars: DKW had lost its production facilities in Eisenach (now in DDR) and reestablished itself in Ingolstadt. A version of
13770-570: The pre-war F9 was introduced as the DKW F89. Borgward introduced 2 new makes with front-wheel drive, the Goliath and the Lloyd in 1950. Gutbrod also came with a car in 1950; the Superior, but withdrew the car in 1954 and concentrated on other products. This car is best remembered for its Bosch fuel-injection . In 1955, one of the first Japanese manufacturers to utilize front-wheel drive with
13905-725: The public, and a few months later the Ruxton automobile . The Cord L-29's drive system was again inspired by racing, copying from the Indianapolis 500 -dominating racers, using the same de Dion layout and inboard brakes. Moreover, the Auburn (Indiana) built Cord was the first ever front-wheel drive production car to use constant-velocity joints . These very specific components allow motive power to be delivered to steered wheels more seamlessly than universal joints , and have become common on almost every front-wheel-drive car, including on
14040-472: The rear car seat. Features on the new Avenger included optional heated/cooled cup holders and Dodge's new "Chill Zone", a feature that comes standard on all Avenger models, which can store up to four 12-US-fl oz cans in the glove box and chill them to 40 °F. The Avenger competed directly with the Chevrolet Malibu and Ford Fusion , with the 2007 and later Chrysler Sebring being aimed at
14175-520: The same transverse-mounted, forward-motor layout as modern front-wheel-drive automobiles. It even resembled the smaller version of its popular Alfa Romeo Giulia . However, due to the financial difficulties in post-war Italy, the 33 never saw production. Had Alfa-Romeo succeed in producing 33, it would have preceded the Mini as the first "modern" European front-wheel-drive compact car. The German car industry resumed from WW2 in 1949/1950. In East Germany (DDR),
14310-427: The second generation of Prelude, launched worldwide in 1982. Additional info: the general agent for Honda in Norway required all Preludes for the Norwegian market to have the ALB-system as a standard feature, making Honda Prelude be the first car delivered in Europe with ABS as a standard feature. The Norwegian general agent also included a sunroof and other options to be standard equipment in Norway, adding more luxury to
14445-424: The small overlap test due to marginal dummy kinematics and slight intrusion into the passenger compartment. In the side test, the Avenger earned a "Good" rating; however, rib fractures were possible for the driver. In the roof strength evaluation, it gained a "Good" rating, as well as for its head restraints and seats. The Avenger earned the "Top Safety Pick" award in 2009, 2010, 2011, 2012, and 2014 as well as earned
14580-424: The stable zone, the pressure is increased again. Past models used a piston for the control of the fluid pressure . Most recent models regulate the pressure by rapidly opening and closing solenoid valves . While the basic principle and architecture has been carried over from passenger car ABS, typical motorcycle characteristics have to be considered during the development and application processes. One characteristic
14715-471: The success of small, inexpensive cars, especially the British Mini . As engineered by Alec Issigonis , the compact arrangement located the transmission and engine sharing a single oil sump – despite disparate lubricating requirements – and had the engine's radiator mounted to the side of the engine, away from the flow of fresh air and drawing heated rather than cool air over
14850-449: The system work: these are a steering wheel angle sensor and a gyroscopic sensor. The theory of operation is simple: when the gyroscopic sensor detects that the direction taken by the car does not coincide with what the steering wheel sensor reports, the ESC software will brake the necessary individual wheel(s) (up to three with the most sophisticated systems), so that the vehicle goes the way
14985-473: The transmission in the sump, and the cooling fan drawing hot air from its side-facing location. Volvo Cars has switched its entire lineup after the 900 series to front-wheel drive. Swedish engineers at the company have said that transversely mounted engines allow for more crumple zone area in a head-on collision. American auto manufacturers are now shifting larger models (such as the Chrysler 300 and most of
15120-586: The transmission-in-sump " Suitcase " engine that it had co-developed with Peugeot in the 1970s for its compact models, starting with the Renault 9 in 1982. Peugeot-Citroen themselves also moved over to the end-on gearbox solution when it phased out the Suitcase unit in favour of the TU-series engine in 1986. Nissan also abandoned the transmission-in-sump concept for its N12-series Cherry/Pulsar in 1982. Perhaps symbolically, British Leyland themselves, heirs to
15255-440: The travel distance of the piston to allow the control unit a more precise regulation. Honda also uses this system of pressure modulation for big sports and touring bikes . Valve and Pump Systems : The main parts which are part of the pressure modulation system are solenoid inlet and outlet valves, a pump, motor, and accumulators/reservoirs. The number of the valves differs from model to model due to additional functionalities and
15390-464: The type of brakes in use. They can be differentiated by the number of channels: that is, how many valves that are individually controlled—and the number of speed sensors. A 2004 Australian study by Monash University Accident Research Centre found that ABS: On high-traction surfaces such as bitumen , or concrete , many (though not all) ABS-equipped cars are able to attain braking distances better (i.e. shorter) than those that would be possible without
15525-473: The use of constant velocity jointed drive axles, along with front wheel drive has evolved into the modern-day mass-market automobile. Some suggest that the introduction of the modern Volkswagen Golf in 1974, from a traditional U.S. competitor, and the introduction of the 1973 Honda Civic , and the 1976 Honda Accord served as a wake-up call for the "Big Three" (only Chrysler already produced front-wheel-drive vehicles in their operations outside North America). GM
15660-407: The valves to reduce hydraulic pressure to the brake at the affected wheel, thus reducing the braking force on that wheel; the wheel then turns faster. Conversely, if the ECU detects a wheel turning significantly faster than the others, brake hydraulic pressure to the wheel is increased so the braking force is reapplied, slowing down the wheel. This process is repeated continuously and can be detected by
15795-455: Was also used on race cars by several ARCA race teams from 1995 until 2000. The Avenger replaced the Charger as Dodge's car for the 2007 NASCAR Nextel Cup Season . It appeared in Dodge Avenger grille, headlights, and taillights as the standard "spec" Car of Tomorrow (CoT) model. It got its first win with former Formula One driver Juan Pablo Montoya in the 2007 Toyota/Save Mart 350 at
15930-588: Was available for several years thereafter, functioned as intended, and proved reliable. In 1969, Ford introduced an anti-lock braking system called "Sure-Track" to the rear wheels of the Lincoln Continental Mark III and Ford Thunderbird , as an option; it became standard in 1971. The Sure-Track braking system was designed with help from Kelsey-Hayes. In 1971, General Motors introduced the "Trackmaster" rear-wheel only ABS as an option on their rear-wheel drive Cadillac models and called
16065-467: Was awarded the coveted European Car of the Year Award in 1986, with very favorable praise from motoring journalists. After this success, Ford began research into Anti-Lock systems for the rest of their range, which encouraged other manufacturers to follow suit. Since 1987 ABS has been standard equipment on all Mercedes-Benz automobiles. Lincoln followed suit in 1993. In 1988, BMW introduced
16200-531: Was built on a 103.7 in (2,634 mm) wheelbase and used either a 2.0 L inline-four engine (the Chrysler 420A) or a Mitsubishi-designed 2.5 L V6 . The four-cylinder was coupled to a five-speed manual transmission , shared with the Mitsubishi Eclipse and Eagle Talon , or a four-speed automatic. The V6 engine was only available with the A604 automatic transmission. The Avengers featured
16335-672: Was developed in the late-1960s for the Concorde aircraft. The modern ABS system was invented in 1971 by Mario Palazzetti (known as 'Mister ABS') in the Fiat Research Center and has become standard in almost every car. The system was called Antiskid and the patent was sold to Bosch who named it ABS. Chrysler , together with the Bendix Corporation , introduced a computerized, three-channel, four-sensor all-wheel ABS called "Sure Brake" for its 1971 Imperial . It
16470-658: Was discontinued in February 1993. The Avenger, along with the similar Chrysler Sebring coupe, was built by Diamond Star Motors (DSM), a joint venture between Chrysler Corporation and Mitsubishi Motors , on a version of the Mitsubishi Galant platform (which also spawned the similar Mitsubishi Eclipse ). Chrysler sold its equity stake to Mitsubishi in 1993. Diamond-Star Motors was renamed Mitsubishi Motors Manufacturing America (MMMA) on July 1, 1995. Avengers and Sebring coupes built from 1994 until 1996 have DSM identification in their engine compartments. The Avenger
16605-541: Was even later with the 1979 Vauxhall Astra / Opel Kadett . Captive imports were the US car makers initial response to the increased demand for economy cars . The popularity of front-wheel drive began to gain momentum, with the 1981 Ford Escort , the 1982 Nissan Sentra , and the 1983 Toyota Corolla . Front-wheel drive became the norm for mid-sized cars starting with the 1982 Chevrolet Celebrity , 1982 Toyota Camry , 1983 Dodge 600 , 1985 Nissan Maxima , 1986 Honda Legend , and
16740-488: Was held at the Indianapolis Motor Speedway on Saturday, 30 May 1925. However, the idea of front-wheel drive languished outside the motor racing arena as few manufacturers attempted the same for production automobiles. Alvis Cars did introduce a commercial model of the front-wheel drive 12/50 racer in 1928, but it was not a success. In France, Jean-Albert Grégoire and Pierre Fenaille developed
16875-485: Was introduced in production vehicles, such systems have become increasingly sophisticated and effective. Modern versions may not only prevent wheel lock under braking, but may also alter the front-to-rear brake bias . This latter function, depending on its specific capabilities and implementation, is known variously as electronic brakeforce distribution , traction control system , emergency brake assist , or electronic stability control (ESC). The concept for ABS predates
17010-486: Was largely solved by making the shorter driveshaft solid, and the longer one hollow, to ensure both shafts experienced elastic twist which was roughly the same. After the 128, Fiat further demonstrated the layout's flexibility, re-configurating the 128 drive train as a mid-engined layout for the Fiat X1/9 . The compact, efficient Giacosa layout – a transversely-mounted engine with transmission mounted beside
17145-752: Was no public information of the test results. By the early 1950s, the Dunlop Maxaret anti-skid system was in widespread aviation use in the UK, with aircraft such as the Avro Vulcan and Handley Page Victor , Vickers Viscount , Vickers Valiant , English Electric Lightning , de Havilland Comet 2c , de Havilland Sea Vixen , and later aircraft, such as the Vickers VC10 , Hawker Siddeley Trident , Hawker Siddeley 125 , Hawker Siddeley HS 748 and derived British Aerospace ATP , and BAC One-Eleven , and
17280-708: Was ranked the "Most American Made" sedan by the American University 's Kogod School of Business 2013 Made in America Auto Index. The Dodge Avenger also has an overall rating of 6.7. The 2008 through 2013 Avenger, also sold as the Chrysler Sebring from 2008 until 2010, and the Chrysler 200 from 2011 through 2013, received an overall "Good" rating by the IIHS, indicating no significant injuries. The car received an overall "Acceptable" rating in
17415-642: Was the Lohner–Porsche of 1897 with an electric motor in each front wheel, produced by Lohner-Werke in Vienna. It was developed by Ferdinand Porsche in 1897 based on a concept developed by American inventor Wellington Adams . Porsche also raced it in 1897. J. Walter Christie of the United States patented a design for a front-wheel-drive car, the first prototype of which he built in 1904. He promoted and demonstrated several such vehicles, notably with transversely mounted engines, by racing at various speedways in
17550-517: Was the elimination of burned or burst tires. The first proper recognition of the ABS system came later with the German engineer Karl Wässel, whose system for modulating braking power was officially patented in 1928. Wässel, however, never developed a working product and neither did Robert Bosch who produced a similar patent eight years later. A similar braking system called Decelostat that used direct-current generators to measure wheel slippage
17685-605: Was the supercharged Alvis 12/50 racing car designed by George Thomas Smith-Clarke and William M. Dunn of Alvis Cars of the United Kingdom. This vehicle was entered in the 1925 Kop Hill Climb in Princes Risborough in Buckinghamshire on 28 March 1925. Harry Arminius Miller of Menomonie, Wisconsin designed the Miller 122 front-wheel drive race-car that was entered in the 1925 Indianapolis 500 , which
17820-401: Was to create the happy combination of a low centre of gravity boxer engine (flat four) with a special frame. Due to post-war financial problems Cemsa could not continue production, but the project was resumed when taken on by Lancia in the 50s. In 1954, Alfa-Romeo had experimented with its first front-wheel-drive compact car named "33" (not related to the sports car similarly named "33"). It had
17955-462: Was used in all ES models until 1999. For the 2000 model year, the V6 and automatic transmission combination were standard on all Avengers, and ABS was an "option" for ES models. The four-cylinder engine was no longer available. Standard features that had previously been optional included power windows and locks. Base models added cruise control and four-wheel disc brakes . The ES coupes now come with standard leather upholstery, keyless remote entry, and
18090-617: Was used in railroads in the 1930s. By 1951, flywheel-based Decelostat was used in aircraft to provide anti skid in landings. The device was on trials first in the United States and later by the British. In 1954, Popular Science revealed that there was preliminary testing of the Decelostat system to prevent car swirling on a heavy brake by the US car manufacturers in Detroit . However, there
18225-622: Was widely used in the National Hot Rod Association and earned the most prominence driven by Darrell Alderman and Scott Geoffrion from 1994 until 2000 as the Dodge Boys . The coupe was used for the 1994 and 1995 incarnations of the International Race of Champions . Although Dodge was IROC's car of choice since 1990, Dodge dropped out of this racing series after the 1995 season. Avenger sheet metal
#957042