Misplaced Pages

#31968

89-457: The Airbus Helicopters H155 (formerly Eurocopter EC155 ) is a long-range medium-lift passenger transport helicopter developed by Eurocopter from its Dauphin family for civil aviation use. It is a twin-engined aircraft and can carry up to 13 passengers along with 1 or 2 crew, depending on customer configuration. The helicopter is marketed for passenger transport, offshore support, VIP corporate transport and casualty transport duties. In 2015,

178-616: A runway . In 1942, the Sikorsky R-4 became the first helicopter to reach full-scale production . Although most earlier designs used more than one main rotor, the configuration of a single main rotor accompanied by a vertical anti-torque tail rotor (i.e. unicopter , not to be confused with the single-blade monocopter ) has become the most common helicopter configuration. However, twin-rotor helicopters (bicopters), in either tandem or transverse rotors configurations, are sometimes in use due to their greater payload capacity than

267-444: A collective input is made, all the blades change equally, and the result is the helicopter increasing or decreasing in altitude. A swashplate controls the collective and cyclic pitch of the main blades. The swashplate moves up and down, along the main shaft, to change the pitch of both blades. This causes the helicopter to push air downward or upward, depending on the angle of attack . The swashplate can also change its angle to move

356-595: A complete range of turbine engines for this market. More than 18,000 Safran Helicopter engines already power helicopters built by the world's leading manufacturers: Airbus Helicopters, AVIC, Sikorsky, Bell Helicopter, Finmeccanica Helicopters (formerly AgustaWestland), Denel, Russian Helicopters, HAL, Boeing, etc. In the military sector, Safran powers the Tiger, NH90, Finmeccanica Helicopters A109 Power, AW101 and many others. Helicopters powered by Safran are deployed by 2,500 customers in 150 countries. Most Turbomeca engines bear

445-417: A constant altitude. The pedals serve the same function in both a helicopter and a fixed-wing aircraft, to maintain balanced flight. This is done by applying a pedal input in whichever direction is necessary to center the ball in the turn and bank indicator . Due to the operating characteristics of the helicopter—its ability to take off and land vertically, and to hover for extended periods of time, as well as

534-612: A cumulative total of 7,000,000 flying hours. Deciding to build on its success with another engine, Rolls-Royce Turbomeca handled development and production of the RTM322 turboshaft engine. During 1995, it was announced that the Rolls-Royce Turbomeca RTM322 turboshaft engine had been selected to power the British Army 's fleet of AgustaWestland Apache attack helicopters . Over the following decades,

623-472: A few more flights and achieved a height of nearly 2.0 metres (6.5 ft), but it proved to be unstable and was abandoned. Turbomeca Since its founding as Turbomeca during 1938, Safran Helicopter Engines has produced over 72,000 turbines. In its early years, it benefitted greatly from a rearmament programme conducted by the French state; operations were disrupted by the occupation of France during

712-464: A five-blade Spheriflex composite main rotor combined with the familiar shrouded Fenestron tail rotor to reduce vibration levels significantly. The EC155 B is powered by two 635 kW (851 shp) Turbomeca Arriel 2C1 turboshaft engines which feature a dual-channel Full Authority Digital Engine Control (FADEC) system. The EC155 B1 features uprated 697 kW (935 shp) Arriel 2C2s. The helicopter can be fitted with an anti-icing system to enable

801-711: A fully operational status during June 1940, the French Government had advised the relocation to the south of France to avoid to the German advance . That same month, Turbomeca repositioned its operations to a newly requisitioned workshop in Saint-Pé-de-Bigorre near the Hispano-Suiza engine factory in Tarbes . However, these buildings were quickly found to be too small for its needs, thus, in 1941,

890-463: A gift by their father, would inspire the Wright brothers to pursue the dream of flight. In 1861, the word "helicopter" was coined by Gustave de Ponton d'Amécourt , a French inventor who demonstrated a small steam-powered model. While celebrated as an innovative use of a new metal, aluminum, the model never lifted off the ground. D'Amecourt's linguistic contribution would survive to eventually describe

979-405: A helicopter determines the size, function and capability of that helicopter design. The earliest helicopter engines were simple mechanical devices, such as rubber bands or spindles, which relegated the size of helicopters to toys and small models. For a half century before the first airplane flight, steam engines were used to forward the development of the understanding of helicopter aerodynamics, but

SECTION 10

#1732793195032

1068-510: A helicopter powered by a gasoline engine with box kites attached to a mast by cables for a rotor, but it never flew. In 1906, two French brothers, Jacques and Louis Breguet , began experimenting with airfoils for helicopters. In 1907, those experiments resulted in the Gyroplane No.1 , possibly as the earliest known example of a quadcopter. Although there is some uncertainty about the date, sometime between 14 August and 29 September 1907,

1157-416: A helicopter. This is because a helicopter generates its own gusty air while in a hover, which acts against the fuselage and flight control surfaces. The result is constant control inputs and corrections by the pilot to keep the helicopter where it is required to be. Despite the complexity of the task, the control inputs in a hover are simple. The cyclic is used to eliminate drift in the horizontal plane, that

1246-725: A higher maximum take-off weight (10,846 lb vs. 10,580 lb). Deliveries of this model began in November 2002 with the Hong Kong Government Flying Service becoming the first operator. In early 2003, Eurocopter completed studies for an even more powerful version of the EC155 B1, designed to better compete with new rotorcraft such as the AgustaWestland AW139 and to better meet military customer's requirements. Several major elements of

1335-589: A price tag of US$ 7–8 million depending on installed equipment. In March 1999, deliveries of the EC155 B commenced, the German Federal Police became the first operator of the type. Between March 1999 and June 2003, roughly 50 EC155 Dauphins were sold, mainly to VIP and off-shore customers. The EC155 B1 was developed with uprated engines, giving it improved performance at high altitude and in hot temperature conditions; this derivative also features

1424-477: A process of rebracketing , the word is often (erroneously, from an etymological point of view) perceived by English speakers as consisting of heli- and -copter , leading to words like helipad and quadcopter . English language nicknames for "helicopter" include "chopper", "copter", "heli", and "whirlybird". In the United States military, the common slang is "helo" pronounced /ˈhiː.loʊ/. A helicopter

1513-441: A rearmament programme during 1937. Over the course of three years, Turbomeca expanded rapidly from an artisanal production to an industrial one to meet the extensive demands of the French aircraft industry. The production figures of the company's first few years of operation indicate this rapid expansion: 18 compressors were produced in 1938, 300 in 1939 and 1,200 in 1940. Although the factory at Mézières-sur-Seine only attaining

1602-494: A rotor. The spinning creates lift, and the toy flies when released. The 4th-century AD Daoist book Baopuzi by Ge Hong ( 抱朴子 "Master who Embraces Simplicity") reportedly describes some of the ideas inherent to rotary wing aircraft. Designs similar to the Chinese helicopter toy appeared in some Renaissance paintings and other works. In the 18th and early 19th centuries Western scientists developed flying machines based on

1691-441: A single main rotor, but torque created by its aerodynamic drag must be countered by an opposed torque. The design that Igor Sikorsky settled on for his VS-300 was a smaller tail rotor. The tail rotor pushes or pulls against the tail to counter the torque effect, and this has become the most common configuration for helicopter design, usually at the end of a tail boom . Some helicopters use other anti-torque controls instead of

1780-562: A site was acquired in Bordes near Pau . Turbomeca progressively transferred to this site between the autumn of 1941 and June 1942. During November 1942, Szydlowski fled to neutral Switzerland . Between October 1942 and 1944, production stalled while its workforce dropped from about 300 to about 50 personnel. Following the liberation of the region by Allied forces in August 1944, Szydlowski returned to Bordes to help revive Turbomeca; much of

1869-586: A staple of the business over subsequent decades. From 1950, Turbomeca produced the tiny centrifugal flow Palas turbojet, producing 1.6 kN (353 lbf ). In addition to the company's own production, the Palas was also produced under license by Blackburn and General Aircraft in the United Kingdom and Continental in the United States . Blackburn had a licence for producing other Turbomeca designs. During 1955, Turbomeca's Artouste II turboshaft engine

SECTION 20

#1732793195032

1958-417: A state called translational lift which provides extra lift without increasing power. This state, most typically, occurs when the airspeed reaches approximately 16–24 knots (30–44 km/h; 18–28 mph), and may be necessary for a helicopter to obtain flight. In forward flight a helicopter's flight controls behave more like those of a fixed-wing aircraft. Applying forward pressure on the cyclic will cause

2047-429: Is a cylindrical metal shaft that extends upwards from the transmission. At the top of the mast is the attachment point for the rotor blades called the hub. Main rotor systems are classified according to how the rotor blades are attached and move relative to the hub. There are three basic types: hingeless, fully articulated, and teetering; although some modern rotor systems use a combination of these. Most helicopters have

2136-460: Is a type of rotorcraft in which lift and thrust are supplied by horizontally spinning rotors . This allows the helicopter to take off and land vertically , to hover , and to fly forward, backward and laterally. These attributes allow helicopters to be used in congested or isolated areas where fixed-wing aircraft and many forms of short take-off and landing ( STOL ) or short take-off and vertical landing ( STOVL ) aircraft cannot perform without

2225-452: Is a type of rotorcraft in which lift and thrust are supplied by one or more horizontally-spinning rotors. By contrast the autogyro (or gyroplane) and gyrodyne have a free-spinning rotor for all or part of the flight envelope, relying on a separate thrust system to propel the craft forwards, so that the airflow sets the rotor spinning to provide lift. The compound helicopter also has a separate thrust system, but continues to supply power to

2314-505: Is being available. During June 1989, another joint venture, MTU Turbomeca Rolls-Royce (MTR) was established as a part of the framework created on behalf of the French and West German governments to developed an advanced multirole battlefield helicopter , the Eurocopter Tiger . Being responsible for developing and producing the Tiger's MTR390 powerplant, MTR was designated as the programme management company responsible for

2403-452: Is called an aerial crane . Aerial cranes are used to place heavy equipment, like radio transmission towers and large air conditioning units, on the tops of tall buildings, or when an item must be raised up in a remote area, such as a radio tower raised on the top of a hill or mountain. Helicopters are used as aerial cranes in the logging industry to lift trees out of terrain where vehicles cannot travel and where environmental concerns prohibit

2492-547: Is equipped to stabilize and provide limited medical treatment to a patient while in flight. The use of helicopters as air ambulances is often referred to as " MEDEVAC ", and patients are referred to as being "airlifted", or "medevaced". This use was pioneered in the Korean War , when time to reach a medical facility was reduced to three hours from the eight hours needed in World War II , and further reduced to two hours by

2581-742: Is offered with a Health and Usage Monitoring System (HUMS). Eurocopter designed the EC155 originally with three configurations, however, another two configurations were added in 2005. The Passenger Transport version can carry 12 passengers in comfort seats or 13 passengers in utility seats, along with 1 or 2 crew. The VIP or Corporate Transport version has a VIP lounge with working space accommodating up to 8 executives. The Casualty Transport version can carry 2 stretchered patients with up to 4 seated medical staff, or 4 patients on stretchers plus 2 seated medical staff. The configurations added in 2005 were for offshore operation and police and parapublic missions ranging from patrol, airborne surveillance, SAR and EMS ,

2670-678: Is the Sud-Ouest Djinn , and an example of the hot tip jet helicopter is the YH-32 Hornet . Some radio-controlled helicopters and smaller, helicopter-type unmanned aerial vehicles , use electric motors or motorcycle engines. Radio-controlled helicopters may also have piston engines that use fuels other than gasoline, such as nitromethane . Some turbine engines commonly used in helicopters can also use biodiesel instead of jet fuel. There are also human-powered helicopters . A helicopter has four flight control inputs. These are

2759-488: Is the leading European manufacturer of turbojet engines for missiles, drones and auxiliary power units. Safran Helicopter Engines has 6,300 employees worldwide, with 5000 based in France. In 2015, the company reportedly produced and delivered 718 new engines, and repaired around 1,700 engines. On 29 August 1938, the company was founded as Turbomeca by the aero engine designers Joseph Szydlowski and André Planiol, following

Eurocopter EC155 - Misplaced Pages Continue

2848-411: Is to control forward and back, right and left. The collective is used to maintain altitude. The pedals are used to control nose direction or heading . It is the interaction of these controls that makes hovering so difficult, since an adjustment in any one control requires an adjustment of the other two, creating a cycle of constant correction. As a helicopter moves from hover to forward flight it enters

2937-468: Is to serve as the basis for KAI's Light Civil Helicopter (LCH) and Light Armed Helicopter (LAH) , featuring numerous changes including a new cockpit, improved gearbox and rotor blades; the LAH shall have a chin-mounted 20 mm cannon and side-mounted guided rockets, countermeasures systems, and be able to carry 6–10 combat troops. The LCH is to enter service in 2020, and the LAH will follow in 2022 to replace

3026-919: The Adour turbojet engine to power the Anglo-French SEPECAT Jaguar . In addition to manufacturing the aero-engine, the company also provided associated support services to end users. The Adour would not only be adopted for the Jaguar, but also various other aircraft, such as the BAE Systems Hawk , the McDonnell Douglas T-45 Goshawk , and Mitsubishi T-2 trainer aircraft, as well as the Mitsubishi F-1 ground attack fighter. In excess of 2,800 Adour engines would eventually be produced, reportedly amassing

3115-572: The Bell 205 and the Erickson S-64 Aircrane helitanker. Helicopters are used as air ambulances for emergency medical assistance in situations when an ambulance cannot easily or quickly reach the scene, or cannot transport the patient to a medical facility in time. Helicopters are also used when patients need to be transported between medical facilities and air transportation is the most practical method. An air ambulance helicopter

3204-588: The Bell 206 with 3,400. Most were in North America with 34.3% then in Europe with 28.0% followed by Asia-Pacific with 18.6%, Latin America with 11.6%, Africa with 5.3% and Middle East with 1.7%. The earliest references for vertical flight came from China. Since around 400 BC, Chinese children have played with bamboo flying toys (or Chinese top). This bamboo-copter is spun by rolling a stick attached to

3293-527: The Cornu helicopter which used two 6.1-metre (20 ft) counter-rotating rotors driven by a 24 hp (18 kW) Antoinette engine. On 13 November 1907, it lifted its inventor to 0.3 metres (1 ft) and remained aloft for 20 seconds. Even though this flight did not surpass the flight of the Gyroplane No. 1, it was reported to be the first truly free flight with a pilot. Cornu's helicopter completed

3382-463: The MD 500 Defender and AH-1J/S Cobra . Airbus foresees a South Korean demand for 100 LCHs and 214 LAHs, and estimates an international market of 300–400 LAH versions to replace legacy attack helicopters. The EC155 B features a completely redesigned cabin providing 30% more passenger space than previous Dauphin helicopter models, plus a 130% increase in baggage hold volume. Other major improvements include

3471-734: The Second World War , but the company survived and rebuilt quickly during the immediate postwar years. Prominent successes during the Cold War include the use of its Artouste II turboshaft engine to power the new Sud Aviation Alouette II helicopter (the first production turbine-powered helicopter in the world) as well as its involvement in Rolls-Royce Turbomeca Limited (a joint venture with British engine manufacturer Rolls-Royce Ltd that produced turbojet and turboshaft engines). During September 2001,

3560-499: The Vietnam War . In naval service a prime function of rescue helicopters is to promptly retrieve downed aircrew involved in crashes occurring upon launch or recovery aboard aircraft carriers. In past years this function was performed by destroyers escorting the carrier, but since then helicopters have proved vastly more effective. Police departments and other law enforcement agencies use helicopters to pursue suspects and patrol

3649-558: The Bambi bucket, are usually filled by submerging the bucket into lakes, rivers, reservoirs, or portable tanks. Tanks fitted onto helicopters are filled from a hose while the helicopter is on the ground or water is siphoned from lakes or reservoirs through a hanging snorkel as the helicopter hovers over the water source. Helitack helicopters are also used to deliver firefighters, who rappel down to inaccessible areas, and to resupply firefighters. Common firefighting helicopters include variants of

Eurocopter EC155 - Misplaced Pages Continue

3738-762: The Chinese top in a model consisting of contrarotating turkey flight feathers as rotor blades, and in 1784, demonstrated it to the French Academy of Sciences . Sir George Cayley , influenced by a childhood fascination with the Chinese flying top, developed a model of feathers, similar to that of Launoy and Bienvenu, but powered by rubber bands. By the end of the century, he had progressed to using sheets of tin for rotor blades and springs for power. His writings on his experiments and models would become influential on future aviation pioneers. Alphonse Pénaud would later develop coaxial rotor model helicopter toys in 1870, also powered by rubber bands. One of these toys, given as

3827-478: The Chinese toy. It was not until the early 1480s, when Italian polymath Leonardo da Vinci created a design for a machine that could be described as an " aerial screw ", that any recorded advancement was made towards vertical flight. His notes suggested that he built small flying models, but there were no indications for any provision to stop the rotor from making the craft rotate. As scientific knowledge increased and became more accepted, people continued to pursue

3916-717: The EC155 was formally renamed to the H155, in line with Eurocopter's corporate rebranding as Airbus Helicopters . It was succeeded in the product line by the Airbus Helicopters H160 . Originally designated AS365 N4, the EC155 was developed from the Eurocopter AS365 N3 Dauphin 2 with the aim of significantly increasing the cabin space of the Dauphin. Development began in September 1996 with

4005-497: The EC155, such its rotor system (albeit modified to operate at slower rotational speeds), were used in the Eurocopter X3 , an experimental high-speed compound helicopter which set an unofficial speed record of 255 knots (293 mph; 472 km/h) in 2013. In 2015, an EC155 was also used by Airbus Helicopters as a flying testbed for new aerodynamic features, such as the rotor blades, biplane stabilizer and canted fenestron, for

4094-526: The French aerospace specialist SNECMA Group acquired the company, after which it was rebranded as Safran Helicopter Engines. The company states that it has more than 2,500 customers in 155 countries. Safran Helicopter Engines has 15 sites and operates on each continent, providing its customers with a proximity service through 44 distributors and certified maintenance centers, 18 Repair & Overhaul Centers, and 90 Field Representatives and Field Technicians. Safran Helicopter Engines subsidiary Safran Power Units

4183-453: The Gyroplane No. 1 lifted its pilot into the air about 0.6 metres (2 ft) for a minute. The Gyroplane No.   1 proved to be extremely unsteady and required a man at each corner of the airframe to hold it steady. For this reason, the flights of the Gyroplane No.   1 are considered to be the first manned flight of a helicopter, but not a free or untethered flight. That same year, fellow French inventor Paul Cornu designed and built

4272-571: The Martian atmosphere is 100 times thinner than Earth's, its two blades spin at close to 3,000 revolutions a minute, approximately 10 times faster than that of a terrestrial helicopter. In 2017, 926 civil helicopters were shipped for $ 3.68 billion, led by Airbus Helicopters with $ 1.87 billion for 369 rotorcraft, Leonardo Helicopters with $ 806 million for 102 (first three-quarters only), Bell Helicopter with $ 696 million for 132, then Robinson Helicopter with $ 161 million for 305. By October 2018,

4361-583: The RTM322 engine was adopted by various operators to power a number of rotorcraft, including the NHIndustries NH90 and AgustaWestland AW101 medium-sized transport helicopters, along with the Eurocopter X³ , a high speed technology demonstrator. During 2003, it was announced that the joint venture was undertaking the development of an enhanced version of the RTM322, taking the powerplant from

4450-562: The Tiger are furnished with more powerful models of the MTU390 engine than had been installed upon the initial examples. During 2013, an agreement between Rolls-Royce and Turbomeca to buy out the former's involvement in Rolls-Royce Turbomeca in exchange for around €293 million ($ 381 million), after which responsibility for undertaking all activities related to the RTM322 engine, including manufacturing and maintenance/services,

4539-403: The aircraft to operate in very cold climates. The all-glass cockpit is equipped with an 'Avionique Nouvelle' integrated digital flight control system featuring Eurocopter's Vehicle and Engine Management Display (VEMD), which utilizes active matrix liquid crystal displays . The EC155 is also equipped with a four-axis digital autopilot, coupled to the engine FADECs for full-envelope protection, and

SECTION 50

#1732793195032

4628-550: The aircraft's handling properties under low airspeed conditions—it has proved advantageous to conduct tasks that were previously not possible with other aircraft, or were time- or work-intensive to accomplish on the ground. Today, helicopter uses include transportation of people and cargo, military uses, construction, firefighting, search and rescue , tourism , medical transport, law enforcement, agriculture, news and media , and aerial observation , among others. A helicopter used to carry loads connected to long cables or slings

4717-466: The aviation industry; and the turboshaft engine for helicopter use, pioneered in December 1951 by the aforementioned Kaman K-225, finally gave helicopters an engine with a large amount of power and a low weight penalty. Turboshafts are also more reliable than piston engines, especially when producing the sustained high levels of power required by a helicopter. The turboshaft engine was able to be scaled to

4806-435: The blades angle forwards or backwards, or left and right, to make the helicopter move in those directions. The anti-torque pedals are located in the same position as the rudder pedals in a fixed-wing aircraft, and serve a similar purpose, namely to control the direction in which the nose of the aircraft is pointed. Application of the pedal in a given direction changes the pitch of the tail rotor blades, increasing or reducing

4895-677: The building of roads. These operations are referred to as longline because of the long, single sling line used to carry the load. In military service helicopters are often useful for delivery of outsized slung loads that would not fit inside ordinary cargo aircraft: artillery pieces, large machinery (field radars, communications gear, electrical generators), or pallets of bulk cargo. In military operations these payloads are often delivered to remote locations made inaccessible by mountainous or riverine terrain, or naval vessels at sea. In electronic news gathering , helicopters have provided aerial views of some major news stories, and have been doing so, from

4984-406: The cockpit from overhead. The control is called the cyclic because it changes cyclic pitch of the main blades. The result is to tilt the rotor disk in a particular direction, resulting in the helicopter moving in that direction. If the pilot pushes the cyclic forward, the rotor disk tilts forward, and the rotor produces a thrust in the forward direction. If the pilot pushes the cyclic to the side,

5073-502: The current 2,400shp (1,800 kW) power range to beyond 2,500shp in the near term and potentially 3,300shp in the longer term after further improvements are finalised. Keith Reid, Rolls-Royce Turbomeca international marketing manager, noted that the RM322 had been originally designed with future growth in mind, and that operators had been placing an increasing emphasis upon hot and high flight capabilities, which necessitated more engine power

5162-470: The cyclic, the collective, the anti-torque pedals, and the throttle. The cyclic control is usually located between the pilot's legs and is commonly called the cyclic stick or just cyclic . On most helicopters, the cyclic is similar to a joystick. However, the Robinson R22 and Robinson R44 have a unique teetering bar cyclic control system and a few helicopters have a cyclic control that descends into

5251-401: The developing Airbus Helicopters H160 helicopter. In 2015, Airbus Helicopters and Korean Aerospace Industries (KAI) formed an agreement to transfer principle manufacturing activity for the EC155 to South Korea ; KAI shall become the sole manufacturer of the type after 2018, and both firms shall be jointly involved in the international marketing and further development of the type. The EC155

5340-483: The early 21st century, as well as recently weaponized utilities such as artillery spotting , aerial bombing and suicide attacks . The English word helicopter is adapted from the French word hélicoptère , coined by Gustave Ponton d'Amécourt in 1861, which originates from the Greek helix ( ἕλιξ ), genitive helikos (ἕλῐκος), "helix, spiral, whirl, convolution" and pteron ( πτερόν ) "wing". In

5429-501: The engine, and was jointly staffed by the partner companies, Turbomeca, Germany 's MTU Aero Engines and Britain's Rolls-Royce . During early 2000, an initial production contract was signed by the German Federal Office of Defence Technology and Procurement (BWB) and MTR; valued at DM430 million and comprising 320 engines plus spares, the contract represented the MTU390's clearance for production. Later-built models of

SECTION 60

#1732793195032

5518-439: The event was taken by Max Skladanowsky , but it remains lost . In 1885, Thomas Edison was given US$ 1,000 (equivalent to $ 34,000 today) by James Gordon Bennett, Jr. , to conduct experiments towards developing flight. Edison built a helicopter and used the paper for a stock ticker to create guncotton , with which he attempted to power an internal combustion engine. The helicopter was damaged by explosions and one of his workers

5607-430: The firm's former staff were re-employed and much of its machinery was recovered as well, enabling a speedy revival during the postwar era. During the late 1940s, Szydlowski opted to focus Turbomeca's design resources on low-power jet propulsion , intended for a new range of jet-powered aircraft, including turbine-powered helicopters . The production of turboshaft engines, which became widely used for rotorcraft, became

5696-486: The first half of the 20th century was that the amount of power produced by an engine was not able to overcome the engine's weight in vertical flight. This was overcome in early successful helicopters by using the smallest engines available. When the compact, flat engine was developed, the helicopter industry found a lighter-weight powerplant easily adapted to small helicopters, although radial engines continued to be used for larger helicopters. Turbine engines revolutionized

5785-466: The granting of their patent application for a supercharger during the previous year. Engine manufacturer Hispano-Suiza promptly ordered a demonstrator to equip its 12 Y engine, which was used on the MS 405 C1 fighter, amongst others. The company benefitted greatly from a decision by the French Government, recognising the looming threat of another World War with neighbouring Nazi Germany , having launched

5874-485: The helicopter being fitted with specific mission equipment for these duties. The aircraft is operated by private individuals, companies and charter operators. It is also operated by government organisations and as an offshore transport for the gas and oil industry. Data from {Eurocopter.com} General characteristics Performance Related development Aircraft of comparable role, configuration, and era Related lists Helicopter A helicopter

5963-531: The helicopter officially announced by Eurocopter at the Paris Air Show in June 1997. The first EC155 helicopter, a modified Dauphin airframe, made its maiden flight at Marignane on 17 June 1997 and the first pre-production EC155 B flew on 11 March 1998. The aircraft received safety certification by the French and German civil aviation authorities on 11 December 1998 and went into production soon after, with

6052-515: The high operating cost of helicopters cost-effective in ensuring that oil platforms continue to operate. Various companies specialize in this type of operation. NASA developed Ingenuity , a 1.8 kg (4.0 lb) helicopter used to survey Mars (along with a rover). It began service in February 2021 and was retired due to sustained rotor blade damage in January 2024 after 73 sorties. As

6141-480: The idea of vertical flight. In July 1754, Russian Mikhail Lomonosov had developed a small coaxial modeled after the Chinese top but powered by a wound-up spring device and demonstrated it to the Russian Academy of Sciences . It was powered by a spring, and was suggested as a method to lift meteorological instruments. In 1783, Christian de Launoy , and his mechanic , Bienvenu, used a coaxial version of

6230-504: The in-service and stored helicopter fleet of 38,570 with civil or government operators was led Robinson Helicopter with 24.7% followed by Airbus Helicopters with 24.4%, then Bell with 20.5 and Leonardo with 8.4%, Russian Helicopters with 7.7%, Sikorsky Aircraft with 7.2%, MD Helicopters with 3.4% and other with 2.2%. The most widespread model is the piston Robinson R44 with 5,600, then the H125/ AS350 with 3,600 units, followed by

6319-662: The lack of an airstrip would make transport via fixed-wing aircraft impossible. The use of transport helicopters to deliver troops as an attack force on an objective is referred to as " air assault ". Unmanned aerial systems (UAS) helicopter systems of varying sizes are developed by companies for military reconnaissance and surveillance duties. Naval forces also use helicopters equipped with dipping sonar for anti-submarine warfare , since they can operate from small ships. Oil companies charter helicopters to move workers and parts quickly to remote drilling sites located at sea or in remote locations. The speed advantage over boats makes

6408-581: The late 1960s. Helicopters have also been used in films, both in front and behind the camera. The largest single non-combat helicopter operation in history was the disaster management operation following the 1986 Chernobyl nuclear disaster . Hundreds of pilots were involved in airdrop and observation missions, making dozens of sorties a day for several months. " Helitack " is the use of helicopters to combat wildland fires . The helicopters are used for aerial firefighting (water bombing) and may be fitted with tanks or carry helibuckets . Helibuckets, such as

6497-555: The limited power did not allow for manned flight. The introduction of the internal combustion engine at the end of the 19th century became the watershed for helicopter development as engines began to be developed and produced that were powerful enough to allow for helicopters able to lift humans. Early helicopter designs utilized custom-built engines or rotary engines designed for airplanes, but these were soon replaced by more powerful automobile engines and radial engines . The single, most-limiting factor of helicopter development during

6586-432: The monorotor design, and coaxial-rotor , tiltrotor and compound helicopters are also all flying today. Four-rotor helicopters ( quadcopters ) were pioneered as early as 1907 in France, and along with other types of multicopters , have been developed mainly for specialized applications such as commercial unmanned aerial vehicles (drones) due to the rapid expansion of drone racing and aerial photography markets in

6675-601: The nearby park, the Parco Forlanini. Emmanuel Dieuaide's steam-powered design featured counter-rotating rotors powered through a hose from a boiler on the ground. In 1887 Parisian inventor, Gustave Trouvé , built and flew a tethered electric model helicopter. In July 1901, the maiden flight of Hermann Ganswindt 's helicopter took place in Berlin-Schöneberg; this was probably the first heavier-than-air motor-driven flight carrying humans. A movie covering

6764-464: The nose to pitch down, with a resultant increase in airspeed and loss of altitude. Aft cyclic will cause the nose to pitch up, slowing the helicopter and causing it to climb. Increasing collective (power) while maintaining a constant airspeed will induce a climb while decreasing collective will cause a descent. Coordinating these two inputs, down collective plus aft cyclic or up collective plus forward cyclic, will result in airspeed changes while maintaining

6853-411: The power normally required to be diverted for the tail rotor to be applied fully to the main rotors, increasing the aircraft's power efficiency and lifting capacity. There are several common configurations that use the counter-rotating effect to benefit the rotorcraft: Tip jet designs let the rotor push itself through the air and avoid generating torque. The number, size and type of engine(s) used on

6942-436: The rotor disk tilts to that side and produces thrust in that direction, causing the helicopter to hover sideways. The collective pitch control or collective is located on the left side of the pilot's seat with a settable friction control to prevent inadvertent movement. The collective changes the pitch angle of all the main rotor blades collectively (i.e. all at the same time) and independently of their position. Therefore, if

7031-406: The rotor in cruise, which allows its rotation to be slowed down , thus increasing the maximum speed of the aircraft. The Lockheed AH-56A Cheyenne diverted up to 90% of its engine power to a pusher propeller during forward flight. There are three basic flight conditions for a helicopter: hover, forward flight and the transition between the two. Hovering is the most challenging part of flying

7120-422: The rotor throughout normal flight. The rotor system, or more simply rotor , is the rotating part of a helicopter that generates lift . A rotor system may be mounted horizontally, as main rotors are, providing lift vertically, or it may be mounted vertically, such as a tail rotor, to provide horizontal thrust to counteract torque from the main rotors. The rotor consists of a mast, hub and rotor blades. The mast

7209-418: The size of the helicopter being designed, so that all but the lightest of helicopter models are powered by turbine engines today. Special jet engines developed to drive the rotor from the rotor tips are referred to as tip jets . Tip jets powered by a remote compressor are referred to as cold tip jets, while those powered by combustion exhaust are referred to as hot tip jets. An example of a cold jet helicopter

7298-483: The skies. Since helicopters can achieve a unique aerial view, they are often used in conjunction with police on the ground to report on suspects' locations and movements. They are often mounted with lighting and heat-sensing equipment for night pursuits. Military forces use attack helicopters to conduct aerial attacks on ground targets. Such helicopters are mounted with missile launchers and miniguns . Transport helicopters are used to ferry troops and supplies where

7387-479: The tail rotor, such as the ducted fan (called Fenestron or FANTAIL ) and NOTAR . NOTAR provides anti-torque similar to the way a wing develops lift through the use of the Coandă effect on the tail boom. The use of two or more horizontal rotors turning in opposite directions is another configuration used to counteract the effects of torque on the aircraft without relying on an anti-torque tail rotor. This allows

7476-448: The throttle is to maintain enough engine power to keep the rotor RPM within allowable limits so that the rotor produces enough lift for flight. In single-engine helicopters, the throttle control is a motorcycle-style twist grip mounted on the collective control, while dual-engine helicopters have a power lever for each engine. A compound helicopter has an additional system for thrust and, typically, small stub fixed wings . This offloads

7565-417: The thrust produced by the tail rotor and causing the nose to yaw in the direction of the applied pedal. The pedals mechanically change the pitch of the tail rotor altering the amount of thrust produced. Helicopter rotors are designed to operate in a narrow range of RPM . The throttle controls the power produced by the engine, which is connected to the rotor by a fixed ratio transmission. The purpose of

7654-572: The vertical flight he had envisioned. Steam power was popular with other inventors as well. In 1877, the Italian engineer, inventor and aeronautical pioneer Enrico Forlanini developed an unmanned helicopter powered by a steam engine . It rose to a height of 13 meters (43 feet), where it remained for 20 seconds, after a vertical take-off from a park in Milan . Milan has dedicated its city airport to Enrico Forlanini, also named Linate Airport , as well as

7743-537: Was adopted for the new Sud Aviation Alouette II helicopter, which became the world's first production turbine-powered helicopter one year later. Starting in 1957, the firm stated manufacture of the Bastan turboprop for the Aérospatiale N 262 airliner. During 1968, a joint venture with British engine manufacturer Rolls-Royce Ltd , named Rolls-Royce Turbomeca Limited , was established to develop and produce

7832-486: Was badly burned. Edison reported that it would take a motor with a ratio of three to four pounds per horsepower produced to be successful, based on his experiments. Ján Bahýľ , a Slovak inventor, adapted the internal combustion engine to power his helicopter model that reached a height of 0.5 meters (1.6 feet) in 1901. On 5 May 1905, his helicopter reached 4 meters (13 feet) in altitude and flew for over 1,500 meters (4,900 feet). In 1908, Edison patented his own design for

7921-503: Was transferred to Turbomeca. Accordingly, Rolls-Royce Turbomeca is now a wholly owned subsidiary of Safran Helicopter Engines. By 2010, Safran Helicopter Engines turbines powered civil, parapublic and defence helicopters for all the leading helicopter manufacturers (mainly Eurocopter , but also AgustaWestland , Sikorsky , Kamov , HAL , NHI). Safran is the world's leading manufacturer of gas turbine engines for both civil and military helicopters. They design, produce, sell and support

#31968