39-703: The Pont Ambroix or Pont d'Ambrussum (French for Ambrussum Bridge ) was a 1st-century BC Roman bridge in the south of France that was part of the Via Domitia . It crossed the Vidourle at Ambrussum between today's Gallargues-le-Montueux in the Gard department and Villetelle in the Hérault department. In the High Middle Ages , a chapel devoted to St Mary was added to the structure. Only one of
78-677: A battle against the Sabines the Romans set one of their wooden bridges on fire, driving the enemy back. Other early wooden bridges used post and lintel construction. Pontoon bridges were built by laying boats from side to side across a river. During Julius Caesar 's campaign in Germany , he built bridges by driving wooden piles into the stream bed from floating platforms and fixing beams at right angles across them to create trestles. Trajan built another bridge supported by stone during
117-456: A flat downstream face, though some bridges, such as a bridge in Chester , are exceptions. Two niches carrying cornices were inserted between pilasters . They were then put above the framed starlings. Roman bridges had spandrels , between which images of dolphins were often inserted. They rarely had wide spans and thick piers with bow -shaped piers that used small openings to allow for
156-448: A foundation. At first, they used heavy timbers as deep foundations in the riverbed, but a later technique involved using watertight walls to redirect the water and then laying a stone foundation in the area. To aid in the construction of a foundation, work was exclusively done during the dry season . This ensured as many piers as possible were accessible. There is some evidence that in order to construct bridges rivers were diverted. Such
195-420: A practice might have been performed by Trajan when constructing his Danube bridge. Roman engineers might have diverted rivers using rudimentary methods and tools. Sometimes dirt was added to the foundation. The foundation of a bridge could either be built above or below water level . Building the bridge above water level resulted in a need for a wider span. Bridge's tunnels and spandrels were designed to decrease
234-531: A reconstruction during the reign of Augustus (27 BC – 14 AD). The Pons Fabricius, built in 62 BC during the late Republic, is the oldest Roman bridge that is still intact and in use. The largest Roman bridge was Trajan's Bridge over the lower Danube , constructed by Apollodorus of Damascus , which remained for over a millennium the longest bridge to have been built both in terms of overall and span length. Roman engineers built stone arch or stone pillar bridges over all major rivers of their Imperium , save two:
273-533: A span of 1.3 metres (4 ft 3 in). Another bridge over the Bibey River in Galicia has a pier 1 metre (3 ft 3 in) wide, arches with a 4.3-metre (14 ft) span, 6-and-9-metre (20 and 30 ft) side arches, and an arch spanning 18.5 metres (61 ft). Wider spans increase the bridge's drainage, reduce water pressure on the spandrels , and reduced the bridge's weight. Trajan's Bridge over
312-670: Is less than a semicircle. The Romans built both single spans and lengthy multiple-arch aqueducts , such as the Pont du Gard and Segovia Aqueduct . Their bridges often had flood openings in the piers, e.g. in the Pons Fabricius in Rome (62 BC), one of the world's oldest major bridges still standing. There were two main types of wooden bridge in Britain. Small timber bridges with girders , and large ones made of stone and wood. Throughout
351-557: The Dacian Wars . Roman engineers gradually developed new techniques to build bridges, such as oval-shaped bases and pierced bases to facilitate the movement of water. Many bridges would have marble reliefs or carvings , but these bridges were likely used exclusively by government officials because of the difficulty and expense of carving marble artwork. There were three major types of Roman bridges. These were wooden, pontoon, and stone bridges. A list of Roman bridges compiled by
390-477: The Danube featured open-spandrel segmental arches made of wood (standing on 40 metres (130 ft) high concrete piers). This was to be the longest arch bridge for a thousand years both in terms of overall and individual span length. The longest extant Roman bridge is the 790-metre (2,590 ft) Puente Romano at Mérida . When building bridges across moving bodies of water, Roman engineers would begin by laying
429-739: The Euphrates , which lay at the frontier to the rival Persian empires , and the Nile , the longest river in the world, which was 'bridged' as late as 1902 by the British Old Aswan Dam . The largest rivers to be spanned by solid bridges by the Romans were the Danube and the Rhine , the two largest European rivers west of the Eurasian Steppe . The lower Danube was crossed by least two ( Trajan's Bridge , Constantine's Bridge ) and
SECTION 10
#1732775401687468-531: The Pons Fabricius , and even after the Fall of the Western Roman Empire , engineers copied their bridges. Roman bridge-building techniques persisted until the 18th century: for example, the prevalence of arches in bridges can be attributed to the Romans. Roman bridges were much larger than the bridges of other civilizations. They could be anywhere from 4.6 to 18.3 metres (15 to 60 ft) long. By
507-757: The voussoir , stronger keystones , vaults , and superior arched bridges. Roman arched bridges were capable of withstanding more stress by dispersing forces across bridges. Many Roman bridges had semicircular arches, but a few were segmental , i.e. with an arc of less than 180 degrees. By the 2nd century BC, the Romans had further refined their bridge-building techniques, using stronger materials such as volcanic ash , lime and gypsum . Also, they began to use iron clamps to hold together bridges, constructing midstream arches, and pentagonal stones to allow for wider vaults . According to Canadian classicist John Peter Oleson , no known stone bridges existed in Italy before
546-527: The 2nd century BC. This view is not supported unanimously: Spanish engineer Leonardo Fernández Troyano suggested that stone bridges have existed since Pre-Roman Italy . Between 150 and 50 BC, many stone Roman bridges were built, the Pons Aemilius being the first. Engineers began to use stone instead of wood to exemplify the Pax Romana and to construct longer-lasting bridges. These were
585-608: The Pons Sublicius, the oldest bridge in ancient Rome, and they were probably common across northern Europe and the Tyrrhenian coast ; however, because of their lack of durability few have survived to the modern day. These bridges were supported by wooden trestles spanned by horizontal timbers and reinforced with struts , and they were possibly cantilevered . In order to simplify the process of cutting trees, multiple shorter timbers were used. Wooden poles were driven into
624-611: The arch as their basic structure , and most used concrete , the first use of this material in bridge-building. Following the conquests of Tarquinius Priscus , Etruscan engineers migrated to Rome, bringing with them their knowledge of bridge-building techniques. The oldest bridge in ancient Rome was the Pons Sublicius . It was built in the 6th century BC by Ancus Marcius over the Tiber River . The Romans improved on Etruscan architectural techniques. They developed
663-540: The bridge from two arches to the one we see today. The site was abandoned when transit patterns changed; the Via Domitia became less important and the community relocated to Lunel-Viel which better served a north–south transit pattern, but the bridge continued in use until the late Middle Ages. The bridge is a Mérimée list National Monument No. PA00103057. The oppidum is Mérimée list National Monument No. PA00103760 Roman bridge The ancient Romans were
702-499: The concrete. Travertine limestone and tuff were used to build Roman bridges, or they could be made of dry rubble or concrete. Often the building materials varied in smoothness , or rustication . Other bridges were made of bossed limestone combined with cornices, voussoirs and slabs. Sometimes bedrock , buttresses , and vaults were used to construct bridges. Bridges built in Iberia tended to have cylindrical vault geometry. In
741-545: The drawing shows only four arches. An 1839 lithograph and a painting by Gustave Courbet (1857) show two arches. The Vidourlades are violent floods on the Vidourle, in which the water flow increases from a minimum of 3 m/s to over 3000 m/s. Floods were recorded 8 October 1723. The floods of 18 November 1745 reduced the bridge from four arches to three. Further major floods occurred 6 October 1812, 21 October 1891, 21 September 1907. The floods of 7 September 1933 reduced
780-455: The earliest surviving bridge featuring a pointed arch, though it is now submerged by the Keban Dam . Roman arches were unable to properly fit into the arch springings, forcing the base of the arches upwards. In the 2nd century, arches become thinner, and spandrels became flat and pierced with holes. They were constructed using a wooden frame to hold wedge-shaped blocks in place. Afterwards
819-471: The empire for opus pontis . The Anglo-Saxons continued this practice with bricg-geworc , a literal translation of opus pontis . Built in 142 BC, the Pons Aemilius , later named Ponte Rotto (broken bridge), is the oldest Roman stone bridge in Rome , with only one surviving arch and pier. However, evidence suggests only the abutment is original to the 2nd century BC while the arch and pier perhaps date to
SECTION 20
#1732775401687858-469: The engineer Colin O'Connor features 330 stone bridges for traffic, 34 timber bridges and 54 aqueduct bridges , a substantial number still standing and even used to carry vehicles. A more complete survey by the Italian scholar Vittorio Galliazzo found 931 Roman bridges, mostly of stone, in as many as 26 different countries (including former Yugoslavia ; see right table). A segmental arch is an arch that
897-416: The first civilization to build large, permanent bridges . Early Roman bridges used techniques introduced by Etruscan immigrants , but the Romans improved those skills, developing and enhancing methods such as arches and keystones . There were three major types of Roman bridge : wooden, pontoon, and stone. Early Roman bridges were wooden, but by the 2nd century BC stone was being used. Stone bridges used
936-486: The first half of the 2nd century BC, blocks of stone held together with iron clamps were used to aid in the construction of bridges. Although Roman bricks were used to build many bridges, they were far more commonly used to build aqueducts. Bridges built from bricks were rare as bricks often failed to survive erosion . The brick bridges that were built were generally used by the military , and they used construction techniques called opus vittatum and opus mixtum ,
975-561: The first large-scale bridges ever constructed. Bridges were constructed by the Roman government to serve the needs of the military and the empire's administration. Sometimes roads and bridges were used for commercial purposes, but this was rare as boats better served the needs of the Roman economy . By the 2nd century Roman techniques had declined, and they had been mostly lost by the 4th century. Some Roman bridges are still used today, such as
1014-418: The flow of water. During construction, cranes were used to move materials and lift heavy objects. Some bridges had aprons . They were used to surround piers. Usually, the aprons covered the area of the stream bed near the bridge. Agrippa used ashlar and bricks to cover the outside of bridges and concrete for footings and water channels. Ashlar was used because large amounts of wood was needed to cast
1053-528: The foundation of the bridge would be put in this area. Cofferdams were constructed of many piles held together. It is possible the piles were interconnected, likely to improve positioning, waterproofness , or both. Cofferdams would have been sealed with packed clay. The cofferdams also needed to be consistently dry. In order to achieve this, engineers would use tools such as buckets to drain the water. Wooden bridges could be burned to stop an attacker, or dismantled quickly. For example, according to Livy , during
1092-509: The ground, and flat pieces of timber laid across them to create a flat surface. Other early techniques used to build wooden bridges involved barges , sometimes they were moored side by side. Workmen would raise weights, sometimes by rope, then it would fall down onto the piles. This method of construction, called pile driving , was necessary for wooden bridges to properly function. Because this technique created cofferdams , which are enclosures build to pump water out of an area. The base for
1131-624: The latter alternating rows of bricks in opus reticulatum . Examples are bridges in Carmona , Palomas , Extremadura , and the Ponte della Chianche in Italy. One brick bridge in Ticino , Switzerland , has stone arches and brick spandrels. Bricks were sometimes used to create parts of bridges, such as vaults , piers with welding joints , and brick and mortar rubble . Early Roman bridges were wooden, including one constructed by Apollodorus and
1170-493: The middle and lower Rhine by four different bridges (the Roman Bridge at Mainz , Caesar's Rhine bridges , the Roman Bridge at Koblenz , the Roman Bridge at Cologne ). For rivers with strong currents and to allow swift army movements, pontoon bridges were also routinely employed. Judging by the distinct lack of records of pre-modern solid bridges spanning larger rivers, the Roman feat appears to be unsurpassed anywhere in
1209-542: The original eleven arches remains in the middle of the river. Ambrussum contains three archaeological sites of international importance: the Colline de Devès which was first occupied in 2300 BC and settled as an oppidum between 300 BC and 100 AD; the Roman staging post on the Via Domitia which had hotels, a baths and industrial buildings; and the Pont Ambroix. The bridge was sketched by Anne Rulman in 1620 and
Pont Ambroix - Misplaced Pages Continue
1248-516: The responsibility of multiple local municipalities. Their shared costs prove Roman bridges belonged to the region overall, and not to any one town (or two, if on a border). The Alcántara Bridge in Lusitania , for example, was built at the expense of 12 local municipalities, whose names were added on an inscription. Later, in the Roman Empire , the local lords of the land had to pay tithes to
1287-585: The rest of the Roman world, except for northern Europe, arched bridges made of stone were common. This was likely due to the climate and rivers of the regions. Rivers were much calmer and water levels were lower in the southern parts of the Empire. This ensured foundations were easy to construct. While in the northern parts it was much harder to lay down foundations due to the high water level, muddy water, and substantial waterflow. The costs of building and repairing bridges, known as opus pontis ("bridge work"), were
1326-473: The time of Augustus around the turn of the 1st millennium the maximum span of Roman bridges increased from around 24 metres (79 ft) in 142 BC to 35 metres (115 ft). The Ponte Sant'Angelo , built during the reign of Hadrian , has five arches each with a span of 18 metres (59 ft). A bridge in Alcántara has piers 1 metre (3 ft 3 in) wide, 47 metres (154 ft) high, and arches with
1365-409: The use of pointed arches . Roman piers were thick enough to support the pressure of an arch. Stone arches allowed bridges to have much longer spans. Usually, iron clamps covered in lead were used to build piers. Because of poor performance underwater, Roman piers were often destroyed over time. Bridges that survived to the modern day were often furnished with cut waters on the upstream side and
1404-790: The weight of the bridge and function as flood arches . The Pons Aemilius probably had stone piers, with wooden roadbeds and arches. They were rebuilt in stone in 142 BC, and either extended from the abutments to the piers , or vice versa. Throughout Roman history, brick or stone arches were used to support bridges' weight. Roman engineers built bridges with one long arch instead of several smaller ones. This practice made construction easier, as they only needed to build one arch on land, instead of many in water. Roman arches were semi-circular and used voussoirs with equal dimensions and conic sections with equal circumference. Later in Roman history arches started to become semi-circular . Sometimes arches were segmented , or not semicircular. This technique
1443-486: The wooden frame was removed, but the weight of the keystone , the last block to be put in place, held it together. Bridges had abutments at each end and piers in the middle, these two design features carrying most of the bridge's weight. Abutments could be constructed in the many arches of a bridge, allowing each to be built separately. Piers were usually twenty-six feet thick and framed with starlings . The late antique Karamagara Bridge represents an early example of
1482-472: The world until into the 19th century. Leonardo Fern%C3%A1ndez Troyano Leonardo Fernández Troyano ( July 9, 1938, Madrid, Spain) is a Spanish engineer , architect and author. He is the co-chair of CFCSL . Leonardo Fernández Troyano is the son to Carlos Fernández Casado and Rita María Troyano de los Ríos. He studied at the School of Civil Engineers, Canals and Ports of Madrid , being part of
1521-508: Was invented by the Romans. Segmented arches allowed greater amounts of flood water to pass, preventing the bridge from being swept away and allowing it to be lighter. The Limyra Bridge in southwestern Turkey has 26 segmental arches with an average span-to-rise ratio of 5.3:1, giving the bridge an unusually flat profile unsurpassed for more than a millennium. The late Roman Karamagara Bridge in Cappadocia in eastern Turkey may represent
#686313