121-613: The Triumph Spitfire is a British sports car manufactured over five production iterations between 1962 and 1980. Styled for Standard - Triumph in 1957 by Italian designer Giovanni Michelotti , the Spitfire was introduced at the London Motor Show in 1962. It was manufactured at the Standard-Triumph Canley works, with approximately 315,000 produced over 18 years. Developed on a shortened variant of
242-526: A Volvo version. The Volvo version kept the same package size as the J-type but with the updated 18 element freewheel and stronger splines through the planet carrier. The Gear Vendors U.S. version uses a larger 1.375 outer diameter output shaft for higher capacity and a longer rear case. Over a period of 40 years, Laycock Engineering manufactured over three and a half million overdrive Units, and over one million of these were fitted to Volvo motorcars. In 2008
363-399: A compression ratio reduced to 7.5:1 to allow it to run on lower octane unleaded fuel. With the addition of a catalytic converter and exhaust gas recirculating system , the engine only delivered 53 bhp (40 kW) (DIN) with a slower 0–60 mph time of 16.3 seconds. The notable exception to this was the 1976 model year, where the compression ratio was raised to 9.1:1. This improvement
484-399: A controversial choice for a "purist" sports car. The Elan sold poorly and was discontinued after three years. The 1996 Lotus Elise , a mid-engined, rear-wheel drive roadster, was much more successful and remained in production until 2021. Roadsters enjoyed a resurgence in the mid-1990s, including the 1989-present Mazda MX-5 , the 1995-2002 BMW Z3 (succeeded by the 2002-2016 BMW Z4 ),
605-488: A cowl composed of the bonnet and wings that opened forward for engine access. The Spitfire's introduction was delayed by its company's financial troubles in the early 1960's and was subsequently announced shortly after Standard Triumph was taken over by Leyland Motors . While taking stock of their new acquisition, Leyland officials found Michelotti's prototype under a dust sheet in a factory corner, and quickly approved it for production. The production design changed little from
726-453: A curve describing the overall drag on the vehicle, it is simple to find the speed at which the total drag forces are the same as the maximum power of the engine. This defines the maximum speed the vehicle is able to reach. The rotational speed of the wheels for that given forward speed is simple to calculate, being the tire circumference multiplied by the RPM. As the tire RPM at maximum speed is not
847-409: A definition. Insurance companies have also attempted to use mathematical formulae to categorise sports cars, often charging more for insurance due to the inherent risk of performance driving. There is no fixed distinction between sports cars and other categories of performance cars, such as muscle cars and grand tourers , with some cars being members of several categories. Traditionally,
968-413: A different gear ratio. If one is not supplied, the engine is forced to run at a higher RPM than optimal. As the engine requires more power to overcome internal friction at higher RPM, this means more fuel is used simply to keep the engine running at this speed. Every cycle of the engine leads to wear, so keeping the engine at higher RPM is also unfavorable for engine life. Additionally, the sound of an engine
1089-498: A distributor with idle speed ignition timing retarded to address emissions. The twin SU carburettors now included overrun valves in the throttle discs and anti-tampering features on carburettor fuel-air mixture nuts. Starting in 1969, US-bound models were "federalised" to comply with safety and emissions regulations. A reduced compression ratio of 8.5:1 resulted in a slight decrease in power (68 bhp) and 73 ft-lbs of torque. However,
1210-816: A few. Another British company, the former aircraft builder Fairey , built a successful all-mechanical unit for the Land Rover , which is still in production in America today. The first production vehicle to feature the Laycock system was the 1948 Standard Vanguard Saloon. The first unit to be created was the A-type overdrive, which was fitted to many sports cars during the 1950s, and into the late 1960s. Several famous marques used A-type overdrives, including Jaguar, Aston Martin, Ferrari, Austin-Healey, Jensen, Bristol, AC, Armstrong Siddeley and Triumph's TR sports car range, from
1331-407: A fixed-ratio transmission arrangement that was much simpler to build. Final drive ratios of 4:1 were common, meaning that the wheels would turn at one fourth the rate they would if directly connected to the engine. In an era when different models of car with different wheel sizes could be accommodated by simply changing the final drive ratio, it made sense for all transmissions to use direct drive as
SECTION 10
#17327723941751452-438: A flatter rear screen. Importantly, the heavily criticised rear suspension was decambered, incorporating what Triumph called a "swing spring". One leaf of the suspension "stack" was eliminated and only the bottom leaf was attached rigidly to the differential. The remaining leaves were mounted to pivot freely — eliminating the worst characteristics of the original swing-axle . This was a different approach than that taken with
1573-409: A higher ratio first gear, which means more gears between the first and the last to keep the engine at its most efficient speed. This is part of the reason that modern automobiles tend to have larger numbers of gears in their transmissions. It is also why more than one overdrive gear is seldom seen in a vehicle except in special circumstances i.e. where high (numerical) differential gear is required to get
1694-436: A large plastic steering wheel. It was nonetheless considered fairly comfortable at the time, as it had wind-down windows and exterior door locks, as well as relatively full instrumentation. These early cars were referred to both as "Triumph Spitfire Mark Is" and "Spitfire 4s", different from the later Spitfire Mark IV. The "Spitfire 4" name indicated the possibility of the appearance of a six-cylinder version. In UK specification
1815-470: A new black spoked steering wheel. Under the bonnet, some markets had the twin SU carburettors replaced with a single Zenith-Stromberg carburettor. The Mark IV featured a redesigned rear, similar to the Triumph Stag and Triumph 2000 models, both also designed by Michelotti. The front end was revised with a new bonnet pressing, eliminating the weld lines on top of the wings, door handles were recessed,
1936-589: A new grille and badges, and the interior featured revised seats, covering most exposed surfaces with rubber cloth. Carpeting replaced the original moulded rubber floor mats. Its base price was £550; the Austin-Healey Sprite's was £505 and the MG Midget's £515. Top speed was claimed to be 96 mph (154 km/h) and its 0–60 mph time of 14.8 seconds was considered "lively". The factory claimed that at highway speeds (70 mph (110 km/h))
2057-493: A new set of column stalk operated minor controls (as fitted already in the TR7 ) replacing the old dashboard mounted knobs and switches. Also added for the model's final years were a wood dash, hazard flashers and an electric screen washer, in place of the previous manual pump operated ones. Options such as the hard top, tonneau cover, map light and overdrive continued to be popular, but wire wheels ceased to be available. The 1980 model
2178-399: A pressed-steel chassis, a gated 4-speed transmission, pushrod-actuated overhead inlet valves , a honeycomb radiator, low-tension magneto ignition , a long wheelbase, a low center of mass and a very effective suspension system. The overall result was a "safe and well-balanced machine" with a higher performance than any other contemporary production car. At the 1903 Gordon Bennett Cup ,
2299-427: A production Simplex 60 hp was entered only due to a specially-built 90 hp racing car being destroyed in a fire; the 60 hp famously went on to win the race. The 1910 Austro-Daimler 27/80 is another early sports car which had success in motor racing. The 27/80 was designed by Ferdinand Porsche , who drove the car to victory in the 1910 Prince Henry Tour motor race. The Vauxhall and Austro-Daimler —like
2420-567: A single Zenith Stromberg carburettor and an 8.5:1 compression ratio) due to the German DIN system; the output was the same for the early Mark IV. Performance was slower than the Mark III due to its weight increase and taller 3.89:1 final drive as opposed to the earlier 4.11:1. The Mk. IV engine displaced 1,296 cc (79.1 cu in) throughout the production run, and in 1973 received larger big-end bearings to rationalise production with
2541-420: A single transverse-leaf swing axle , an arrangement, that unless ameliorated by any of several options, can allow rear tyres to undergo large camber changes during fast cornering, leading to oversteer – a dynamically unstable condition in which a vehicle can lose control and spin. As did many manufacturers who used a swing axle arrangement (e.g., Mercedes, Renault, Volkswagen), Triumph would later modify
SECTION 20
#17327723941752662-513: A variety of models, including 1968–1980 MGBs , the MGC , the Ford Zephyr , early Reliant Scimitars , TVRs, and Gilberns . The J-type overdrive was introduced in the late 1960s, and was adapted to fit Volvo, Triumph, Vauxhall/Opel, American Motors and Chrysler motorcars, and Ford Transit vans. The P-type overdrive marked the last updates and was manufactured in a Gear Vendors U.S. version and
2783-422: Is a range of gear ratios that can match engine power to air resistance, and the most fuel efficient is the one that results in the lowest engine speed. Therefore, a car needs one gearing to reach maximum speed but another to reach maximum fuel efficiency at a lower speed. With the early development of cars and the almost universal rear-wheel drive layout, the final drive (i.e. rear axle ) ratio for fast cars
2904-452: Is an iconic sports car of the early 1960s, due to its attractive styling and claimed top speed of 241 km/h (150 mph). The E-type was produced for 14 years and was initially powered by a six-cylinder engine, followed by a V12 engine for the final generation. In 1962, the MG B introduced a new era of affordable lightweight four-cylinder roadsters. The MG B used a unibody construction and
3025-402: Is common. However, due to historical particularities, this was not always practical. In the conventional rear-wheel drive layout , the transmission system normally contained two sections, the "gearbox" or "transmission" mounted behind the engine, and the "final drive" mounted in the rear axle at the rear of the car. The reason for this separation of duties between the front and back of the car
3146-545: Is identified by large plastic over-riders and wing mounted reflectors on the front and back wings. US specification models up to 1978 featured chrome bumpers, and on the 1979 and 1980 models these were replaced by black rubber bumpers with built-in over-riders, using chassis extensions to support the bumpers. Detail improvements continued to be made throughout the 1500's production run, including reclining seats with "chequered brushed nylon centre panels" and head restraints, introduced for domestic market cars early in 1977 along with
3267-481: Is limited by the power required to drive it against air resistance, which increases with speed. At the maximum possible speed, the engine is running at its point of maximum power, or power peak , and the car is traveling at the speed where air resistance equals that maximum power. There is therefore one specific gear ratio at which the car can achieve its maximum speed: the one that matches that engine speed with that travel speed. At travel speeds below this maximum, there
3388-406: Is notable for using a three-seat layout, where the front row consists of a centrally-located driver's seat. The location of the engine and driven wheels significantly influence the handling characteristics of a car and are therefore crucial in the design of a sports car. Traditionally, most sports cars have used rear-wheel drive with the engine either located at the front ( FR layout ) or in
3509-399: Is off, the automatic transmission shifting is limited to the lower gears. Overdrive should usually be selected when the average speed is above 70 km/h (40-45 mph). The automatic transmission automatically shifts from OD to direct drive when more load is present. When less load is present, it shifts back to OD. Under certain conditions, for example driving uphill, or towing a trailer,
3630-416: Is one additional consideration which meant that the top gear of most gearboxes was 1:1 or "direct drive". This is chosen for efficiency, as it does not require any gears to transmit power and so reduces the power lost by them. This was particularly important in the early days of cars, as their straight-cut gears were poorly finished, noisy and inefficient. The final drive then took this output and adjusted it in
3751-509: Is strongly related to the RPM, so running at lower RPM is generally quieter. If one runs the same RPM transmission exercise outlined above for maximum speed, but instead sets the "maximum speed" to that of highway cruising, the output is a higher gear ratio that provides ideal fuel mileage. In an era when cars were not able to travel very fast, the maximum power point might be near enough to the desired speed that additional gears were not needed. But as more powerful cars appeared, especially during
Triumph Spitfire - Misplaced Pages Continue
3872-409: Is the highest gear in the transmission. Overdrive allows the engine to operate at a lower RPM for a given road speed. This allows the vehicle to achieve better fuel efficiency, and often quieter operation on the highway. When it is switched on, an automatic transmission can shift into overdrive mode after a certain speed is reached (usually 70+ km/h [40-45 mph or more] depending on the load). When it
3993-448: Is thus overdriven, and a transmission capable of doing this became termed an "overdrive" transmission. The device for achieving an overdrive transmission was usually a small separate gearbox, attached to the rear of the main gearbox and controlled by its own shift lever. These were often optional on some models of the same car. As popular cars became faster relative to legal limits and fuel costs became more important, particularly after
4114-449: The 1973 oil crisis , the use of five-speed gearboxes became more common in mass-market cars. These had a direct (1:1) fourth gear with an overdrive fifth gear, replacing the need for the separate overdrive gearbox. With the popularity of front wheel drive cars, the separate gearbox and final drive have merged into a single transaxle . There is no longer a propeller shaft and so one meaning of "overdrive" can no longer be applied. However
4235-520: The Audi RS 2 Avant . Ford Europe withdrew from the sports car market at the end of 1986 when the Capri was discontinued after a production run of nearly two decades. There was no direct successor, as Ford was concentrating on higher-performance versions of its hatchback and saloon models at the time. In 1989, a new generation of Lotus Elan roadster was released which used a front-wheel drive layout,
4356-541: The BMW 303 , Citroën Traction Avant and Fiat 508 — offered similar handling and comfort to the more expensive sports cars. Powerful, reliable, and economical (although softly suspended) American saloons began to be imported to Europe in significant numbers. Sports car ownership was increased through models such as the Austin 7 and Wolseley Hornet six , however many of these sports cars did not offer any performance upgrades over
4477-623: The Bentley Speed Six (1928-1930), with the former famously described by Bugatti's founder as "the fastest lorry in the world". Between the Great Depression and the World War II the pre-war era was a period of decline in importance for sports car manufacturers, although the period was not devoid of advances, for example streamlining . Cheap, light-weight family sedans with independent front suspension— such as
4598-555: The English company Laycock Engineering (later GKN Laycock), at its Little London Road site in Sheffield . The system devised by de Normanville was adopted and manufactured by Laycock after his chance meeting with a Laycock Products Engineer. De Normanville overdrives were found in vehicles manufactured by Standard-Triumph , who were first, followed by Ford , BMC and British Leyland , Jaguar , Rootes Group and Volvo to name only
4719-520: The Jensen FF became the first sports car to use all-wheel drive . The Ford Capri is a 2+2 coupe that was produced from 1968 to 1986 and intended to be a smaller European equivalent of the Ford Mustang. A main rival to the Capri was Opel Manta , which was produced from 1970 to 1988. The 1973-1978 Lancia Stratos was a mid-engined two-seat coupe that was powered by a Ferrari V6 engine. This
4840-517: The TR6 2.5-litre engines. The engine was also detuned to meet new emissions regulations. With the overall weight also increasing to 1,717 lb (779 kg) performance dropped, with 0 to 60 mph (0 to 97 km/h) now in 15.8 seconds and top speed reduced to 90 mph (140 km/h). Fuel economy was 32 mpg ‑imp (8.8 L/100 km; 26.6 mpg ‑US ). A revised hardtop also became available, with rear quarter-lights and
4961-632: The Triumph GT6 Mk II (GT6+) and Triumph Vitesse Mark 2 , both of which received new lower wishbones and Rotoflex half-shaft couplings. The result on all these cars was improved handling. The Mark IV went on sale in the UK at the end of 1970 with a base price of £735. In 1973 in the United States and Canada, and 1975 in the rest of the world, the 1500 engine was used on the MK IV body to make
Triumph Spitfire - Misplaced Pages Continue
5082-526: The Triumph Herald saloon's chassis, the Spitfire shared the Herald's running gear and Standard SC engine . The design used body-on-frame construction, augmented by structural components within the bodywork and rear trailing arms attached to the body rather than the chassis. A manually deployable convertible top, substantially improved on later models, provided weather protection and a bespoke hard-top
5203-440: The transmission unit. It can either couple the input driveshaft directly to the output shaft (or propeller shaft ) (1:1), or increase the output speed so that it turns faster than the input shaft (1:1 + n ). Thus the output shaft may be "overdriven" relative to the input shaft. In newer transmissions, the overdrive speed(s) are typically as a result of combinations of planetary/epicyclic gearsets which are integrated in
5324-520: The "thrill of driving" or are marketed "using the excitement of speed and the glamour of the (race)track" However, other people have more specific definitions, such as "must be a two-seater or a 2+2 seater" or a car with two seats only. In the United Kingdom, early recorded usage of the "sports car" was in The Times newspaper in 1919. The first known use of the term in the United States
5445-493: The 0–60 time of 14 seconds was still faster than the Mark II. The instrument panel was moved in front of the driver, and new seats were introduced with integrated headrests to help against whiplash. Cosmetically, the wood dash was replaced with a matte black finished assembly intended to imitate an aircraft cockpit. The Mark III's final production year (1970) included an integrated rear reverse and license plate lamp, side lamps at
5566-403: The 1905 Isotta Fraschini Tipo D, the 1906 Rolls-Royce Silver Ghost , the 1908 Delage , the 1910 Bugatti Type 13 , and the 1912 DFP 12/15 . Early motor racing events included the 1903 Paris–Madrid race , the 1905-1907 Herkomer Trophy, the 1908-1911 Prince Henry Tour and the 1911–present Monte Carlo Rally . The Prince Henry Tours (which were similar to modern car rallies) were among
5687-495: The 1921 Coppa Florio . Another approach— such as that used by Morris Garages— was to convert touring cars into sports cars. The first 24 Hours of Le Mans race for sports cars was held in 1923, although the two-seat sports cars only competed in the smallest class, with the majority of cars entered being four-seat fast touring cars. "This race, together with the Tourist Trophy Series of Races , organised after
5808-404: The 1948 Ferrari 166 S . A new concept altogether was the modern Gran Turismo class from Italy, which was in effect unknown before the war: sustained high-speed motoring from relatively modest engine size and compact closed or berlinetta coachwork. The 1947 Maserati A6 1500 two-seat berlinetta was the first production model from Maserati. In Germany, the motor industry was devastated by
5929-432: The 1960s, this disparity between the maximum power point and desired speed grew considerably. This meant that cars were often operating far from their most efficient point. As the desire for better fuel economy grew, especially after the 1973 oil crisis , the need for a "cruising gear" became more pressing. The obvious solution to this problem would be to add more gears to the transmission. Indeed, in modern vehicles this
6050-529: The 1964 Tour de France rally, coming in second overall, and won the 1964 Geneva Rally. In 1965, a Spitfire won its class in the Alpine Rally . Notes Bibliography Sports car A sports car is a type of car that is designed with an emphasis on dynamic performance, such as handling , acceleration, top speed, the thrill of driving, and racing capability. Sports cars originated in Europe in
6171-499: The 1980 Deutsche Rennsport Meisterschaft and Giro d'Italia automobilistico marathon. The Montecarlo was a basis for the silhouette racing car , Lancia Rally 037 . In the 1970s, turbocharging began to be adopted by sports cars, such as the BMW 2002 Turbo in 1973, the first Porsche 911 Turbo in 1975, and the Saab 99 Turbo in 1978. Turbocharging became increasingly popular in the 1980s, from relatively affordable coupes such as
SECTION 50
#17327723941756292-452: The 1980–1986 Renault Fuego and 1992–1996 Rover 220 Coupé Turbo , to expensive supercars such as the 1984-1987 Ferrari 288 GTO and 1987-1992 Ferrari F40 . In the late 1980s and early 1990s, several manufacturers developed supercars that competed for production car top speed records . These cars included the 1986–1993 Porsche 959 , 1991–1995 Bugatti EB 110 , 1992–1994 Jaguar XJ220 and 1993–998 McLaren F1 . The 1980-1995 Audi Quattro
6413-506: The 1990s, all-wheel drive has become more common in sports cars. All-wheel drive offers better acceleration and favorable handling characteristics (especially in slippery conditions), but is often heavier and more mechanically complex than traditional layouts. Examples of all-wheel drive sports cars are the Lamborghini Huracan , Bugatti Veyron , and Nissan GT-R . Rear engine layouts are not typical for sports cars, with
6534-425: The 1995-2002 MG F , the 1996–present Porsche Boxster and the 1998–present Audi TT . Overdrive (mechanics) Overdrive is the operation of an automobile cruising at sustained speed with reduced engine speed (rpm), leading to better fuel consumption, lower noise, and lower wear. The term is ambiguous. The most fundamental meaning is that of an overall gear ratio between engine and wheels, such that
6655-515: The Herald saloon. Where the Austin A30 used unitary construction , the Herald used a separate backbone chassis — which Triumph was able to downsize, saving the cost of developing a completely new chassis-body unit. Giovanni Michelotti , who had designed the Herald, styled the bodywork, which featured wind-down windows (in contrast to the Sprite and Midget , which used side curtains) and
6776-418: The Mark III a comparatively quick car by the standards of the day. Options included wire wheels, factory hard top and a Laycock de Normanville overdrive . The Mark III was the fastest Spitfire yet, achieving 60 mph (97 km/h) in 13.4 seconds, and reaching a top speed of 95 mph (153 km/h). Average fuel consumption was 33mpg. The Mark III continued production into 1971, well after introduction of
6897-569: The Mark IV. On 8 February 1968, Standard-Triumph general manager George Turnbull drove the 100,000th Triumph Spitfire off the Canley production line. More than 75% of this number had been exported outside the UK, including 45% to the US and 25% to mainland European markets. The 1968 model featured dual system (aka tandem) brakes with a brake failure warning device. The engine used a revised camshaft and
7018-468: The Mercedes Simplex 60 hp— were production fast touring cars. The 1912 Hispano-Suiza Alfonso XIII is also considered one of the earliest sports cars, as it was a "purpose built, high performance, two-seater production automobile". The model was named after King Alfonso XIII of Spain , a patron of the car's chief designer and an enthusiast for the marque. Other early sports cars include
7139-490: The Spitfire 1500. Although in this final incarnation the engine was rather rough and more prone to failure than the earlier units, torque was greatly increased by increasing the cylinder stroke to 87.5 mm (3.44 in), which made it much more drivable in traffic. While the rest of the world saw 1500s with a compression ratio of 8.0:1, the American market model was fitted with a single Zenith-Stromberg carburettor and
7260-566: The Spitfire Mark II launched with a retuned engine, featuring a revised camshaft profile, water-heated intake manifold, and tubular exhaust manifold, increasing power to 67 bhp (50 kW) at 6,000 rpm. The coil-spring design clutch of the Mark I was replaced with a Borg & Beck diaphragm spring clutch; North American models retained the coil-spring housing and were also equipped with ACDelco distributors. Exterior trim featured
7381-692: The TR2 through to the end of the 1972 model year of the TR6. In 1959, the Laycock Engineering Company introduced the D-type overdrive, which was fitted to a variety of motor cars including Volvo 120 and 1800s , Sunbeam Alpines and Rapiers , Triumph Spitfires , and also 1962–1967 MGBs (those with 3-synchro transmissions). From 1967 the LH-type overdrive was introduced, and this featured in
SECTION 60
#17327723941757502-411: The U.S. company Gear Vendors, Inc. of El Cajon, California purchased all the overdrive assets of GKN to continue production of the U.S. version and all spares for J and P types worldwide. The system features an oil pressure operated device attached to the back of the standard gearbox operating on the gearbox output shaft. Through a system of oil pressure, solenoids and pistons, the overdrive would drop
7623-534: The automotive aftermarket you can also retrofit overdrive to existing early transmissions. Overdrive was widely used in European automobiles with manual transmission in the 60s and 70s to improve mileage and sport driving as a bolt-on option but it became increasingly more common for later transmissions to have this gear built in. If a vehicle is equipped with a bolt-on overdrive (e.g.: GKN or Gear Vendors) as opposed to having an overdrive built in one will typically have
7744-450: The axle), and tire size. The rotation speed problem comes into effect when the differential gearing is a high ratio and an overdrive is used to compensate. This may create unpleasant vibrations at high speeds and possible destruction of the driveshaft due to the centripetal forces or uneven balance. The driveshaft is usually a hollow metal tube that requires balancing to reduce vibration and contains no internal bracing. The higher speeds on
7865-426: The benefit to fuel economy. Overdrive is included in both automatic and manual transmissions as an extra gear (or two in some cases). When using overdrive gearing, the car's engine speed drops, reducing wear and normally saving fuel. Since 1981 U.S. corporate average fuel economy (CAFE) legislation, virtually all domestic vehicles have included overdrive to save fuel. One should refer to the car's owner's manual for
7986-464: The bonnet. Additional exterior changes introduced included a zip up rear window, black radiator grille and a black (vs body coloured) windscreen surround. Full wheel covers of two styles were used including the 1969 introduced model with "SPITFIRE" circumscribing the hub and a unique derivative without the branding. Interior changes included a steering column mounted ignition switch, a key-in-ignition warning buzzer, driver's side under-dash courtesy lamp and
8107-543: The car achieved 38.1 miles per imperial gallon (7.41 L/100 km; 31.7 mpg ‑US ). The Mark III, introduced in March 1967, was the first major facelift to the Spitfire. The front bumper was raised in response to new crash regulations, and the front coil springs were slightly raised. Slightly revised bonnet pressings were carried over. Rear overriders were deleted and bumper mounted reversing lights became standard (initially as two separate lights on either side of
8228-479: The car appeared during the next year or two, all conforming to the same basic design and earning for themselves a reputation second to none for fast and reliable travel. The 60-h.p. cars were announced late in 1902. The cars were possessed of a very real performance superior to anything else which could be bought at the time... and the model achieved an almost invincible position among the fast cars of its day. The Sports Car: Development and Design The basis for
8349-408: The car is over-geared , and cannot reach its potential top speed, i.e. the car could travel faster if it were in a lower gear, with the engine turning at higher RPM. The power produced by an engine increases with the engine's RPM to a maximum, then falls away. The point of maximum power is somewhat lower than the absolute maximum engine speed to which it is limited, the " redline ". A car's speed
8470-490: The convertible top received squared-off corners. The interior was revised to include a full-width dashboard, with instruments ahead of the driver rather than over the centre console, initially finished in black plastic and then from 1973 finished in wood. The engine was now rated at 63 horsepower for the UK market, with a 9:1 compression ratio and twin SU HS2 carburettors. (The less powerful North American version continued to use
8591-455: The days before automatic transmissions were common, especially in the 1950s, many rear-wheel drive American cars were available with an overdrive option. With substantial improvements developed in Muncie, Indiana , by William B. Barnes for production by its Warner Gear Division, BorgWarner provided the box that was factory-installed between the transmission and a foreshortened driveshaft. Since
8712-411: The development of performance cars such as the 1910 Vauxhall Prince Henry , 1910 Sunbeam 12/16 , 1910 Talbot 25 hp , 1910 Straker-Squire 15 hp and 1913 Star 15.9 hp . Following the halt in sports car production caused by World War I , Europe returned to manufacturing automobiles from around 1920. It was around this time that the term 'Sports Car' began to appear in the motor catalogues, although
8833-399: The driveshaft and related parts can cause heat and wear problems if an overdrive and high differential gearing (or even very small tires) are combined, and create unnecessary friction. This is especially important because the differential gears are bathed in heavy oil and seldom provided with any cooling besides air blowing over the housing. The impetus is to minimize overdrive use and provide
8954-489: The early 1910s and are currently produced by many manufacturers around the world. Definitions of sports cars often relate to how the car design is optimised for dynamic performance, without any specific minimum requirements; both a Triumph Spitfire and Ferrari 488 Pista can be considered sports cars, despite vastly different levels of performance. Broader definitions of sports cars include cars "in which performance takes precedence over carrying capacity", or that emphasise
9075-400: The early 1920s, the cost to produce a racing car was not significantly higher than a road car, therefore several manufacturers used the design from the current year's racing car for the next year's sports car. For example, the 1921 Ballot 2LS based on the racing car that finished third at the 1921 French Grand Prix. The Benz 28/95PS was also a successful racing car, with victories including
9196-463: The exact origin of the name is not known. The decade that followed became known as the vintage era and featured rapid technical advances over the preceding Brass Era cars . Engine performance benefited from the abandonment of " tax horsepower " (where vehicles were taxed based on bore and number of cylinders, rather than actual power output) and the introduction of leaded fuel , which increased power by allowing for higher compression ratios . In
9317-472: The first supercars . Other significant European models of the 1960s and 1970s which might be considered supercars today are the Ferrari 250 GTO (1962-1964), Ferrari 250 GT Lusso (1963-1964), Ferrari 275 GTB/4 (1966-1968), Maserati Ghibli (1967-1973), Ferrari Daytona (1968-1973), Dino 246 (1969-1974), De Tomaso Pantera (1971-1993), Ferrari 308 GTB (1975-1980) and BMW M1 (1978-1981). In 1966,
9438-528: The first World War by the R.A.C. , appealed to the public imagination and offered to the manufacturers of the more sporting cars an excellent opportunity for boosting sales of their products." The classic Italian road races— the Targa Florio , and the Mille Miglia (first held in 1927)— also captured the public's imagination. By 1925, the higher profits available for four-seater cars resulted in
9559-454: The front and rear and new badging. The separate "Triumph" letters on the front of the bonnet were removed and "Triumph" and "Spitfire" rectangular badges were used in the front, rear sides and rear. A limited number of U.S. market 1970s were adorned with an RAF style "Spitfire" badge (U.K. models had a plain badge without the RAF roundel) that rested in the right corner (car opposing point of view) of
9680-474: The fundamental meaning, that of an overall ratio higher than the ratio for maximum speed, still applies: higher gears, with greater ratios than 1:1, are described as "overdrive gears". The power needed to propel a car at any given set of conditions and speed is straightforward to calculate, based primarily on the total weight and the vehicle's speed. These produce two primary forces slowing the car: rolling resistance and air drag . The former varies roughly with
9801-451: The highest gear. As noted earlier, however, this would cause the engine to operate at too high an RPM for efficient cruising. Although adding the cruising gear to the main gearbox was possible, it was generally simpler to add a separate two-gear overdrive system to the existing gearbox. This not only meant that it could be tuned for different vehicles, but had the additional advantage that it could be offered as an easily installed option. With
9922-430: The inline four produced 63 bhp (47 kW) at 5,750 rpm, and 67 lb⋅ft (91 N⋅m) of torque at 3,500 rpm. This gave a top speed of 92 mph (148 km/h), and a 0 to 60 mph (97 km/h) acceleration in 16.4 seconds. Average fuel consumption was 31 mpg. For 1964 an overdrive became optional to the four-speed manual gearbox . Wire wheels and a hard top were also available. In March 1965
10043-573: The late 1920s were AC Cars , Alfa Romeo , Alvis , Amilcar , Bignan and Samson, Chenard-Walcker , Delage , Hispano-Suiza , Hotchkiss , Mercedes-Benz and Nazzaro . Two cars from the Vintage Era that would influence sports cars for many years were the Austin Seven and MG M-type "Midget". Successful sports cars from Bentley during this era were the Bentley 3 Litre (1921-1929) and
10164-518: The mass-produced cars upon which they were based. The highest selling sports car company of the 1930s was Morris Garages , who produced 'MG Midget' models of the M-Type , J-Type , P-Type and T-Type . The K3 version of the K-Type Magnette was a successful racing car, achieving success in the Mille Miglia , Tourist Trophy and 24 Hours of Le Mans . The Bugatti Type 57 (1934-1940)
10285-537: The middle of the vehicle ( MR layout ). Examples of FR layout sports cars include the Caterham 7 , Mazda MX-5 , and the Dodge Viper . Examples of MR layout sports cars are the Ferrari 488 , Ford GT , and Toyota MR2 . To avoid a front-heavy weight distribution , many FR layout sports cars are designed so that the engine is located further back in the engine bay, as close to the firewall as possible. Since
10406-544: The most common layout for sports cars was a roadster (a two-seat car without a fixed roof). However, there are also several examples of early sports cars with four seats. Sports cars are not usually intended to transport more than two adult occupants regularly, so most modern sports cars are generally two-seat or 2+2 layout (two smaller rear seats for children or occasional adult use). Larger cars with more spacious rear-seat accommodation are usually considered sports sedans rather than sports cars. The 1993-1998 McLaren F1
10527-809: The notable exception of the Porsche 911 . The front-wheel drive layout with the engine at the front ( FF layout ) is generally the most common for cars, but it is not as common among traditional sports cars. Nonetheless, the FF layout is used by sport compacts and hot hatches such as the Mazdaspeed3 . Sports cars with an FF layout include the Fiat Barchetta , Saab Sonett , or Opel Tigra . The ancestor of all high-performance cars had its origin in Germany. The 28-h.p. Cannstatt-Daimler racing car of 1899
10648-457: The number plate, latterly as a single light in a new unit above the number plate). The interior received a wood-veneer instrument surround and a smaller, 15-inch, wire spoked steering wheel. A folding hood replaced the earlier, more complicated design. For most of the Mark III range, the instrument cluster remained centre-mounted (as in the Mark I and Mark II), easily accommodating right-hand and left-hand drive versions. The 1,147 cc engine
10769-543: The option to use the overdrive in more gears than just the top gear. In this case gear changing is still possible in all gears, even with overdrive disconnected. Overdrive simply adds effective ranges to the gears, thus overdrive third and fourth become in effect "third-and-a-half" and a fifth gear. In practice this gives the driver more ratios which are closer together providing greater flexibility particularly in performance cars. An overdrive consists of an electrically or hydraulically operated epicyclic gear train bolted behind
10890-425: The overdrive function, if enabled, could be shifted by simply easing up on the accelerator without depressing the clutch pedal , the action was much like a semi-automatic. Also, an electrically operated solenoid would deactivate the unit via a switch under the accelerator pedal providing the equivalent of the kickdown of the automatic. A knob connected to a bowden cable , similar to some emergency brake applications,
11011-456: The philosophy of achieving performance through minimizing weight and has been rated as one of the top 10 sports cars of the 1960s. The Elan featured fibreglass bodies, a backbone chassis, and overhead camshaft engines. A different style of roadster was the AC Cobra , released in 1962, which was fitted with V8 engines up to 7.0 L (427 cu in) in size by Shelby . The Porsche 911
11132-423: The production of two-seat sports cars being limited to smaller manufacturers such as Aston-Martin (350 Astons built from 1921 to 1939) and Frazer-Nash (323 cars built from 1924 to 1939). Then by the late 1920s, the cost of producing racing cars (especially Grand Prix cars) escalated, causing more manufacturers to produce cars for the growing sports car market instead. Significant manufacturers of sports cars in
11253-433: The proper speed to run at overdrive. All engines have a range of peak efficiency and it is possible for the use of overdrive to keep the engine out of this range for all or part of the time of its use if used at inappropriate speeds, thus cutting into any fuel savings from the lower engine speed. Overall drivetrain reduction comes down to three basic factors: transmission gearing (including overdrive), differential gearing (in
11374-407: The prototype: the full-width rear bumper was replaced by two part-bumpers curving around each corner, with overriders. Mechanicals derived from the Herald saloon/sedan, with the notable addition of front disc brakes. Bodywork was bolted to the much-modified Herald chassis, the outer rails and the rear outriggers having been removed; with structural outer sills to stiffen the overall design. The engine
11495-505: The rear suspension. In 1970, the rear suspension was decambered, by incorporating what Triumph called a "swing spring". One leaf was eliminated from the stack and only the bottom leaf was attached rigidly to the differential. The remaining leaves were mounted to pivot freely — thereby eliminating the worst characteristics of the original swing-axle design. The Spitfire was an inexpensive small sports car and as such received rather basic trim by today's standards, including rubber mats and
11616-399: The revs on whatever gears it was used on by 22% (.778). For instance, the overdrive system applied to a Triumph TR5 operates on 2nd, 3rd and top gear. When engaged, the overdrive would drop the revs from 3000 by 666 RPM, or from 3500 the drop would be 777 RPM to 2723 net. The advantages this reduced rpm had on fuel consumption was most often quite near 22% decrease during highway driving. In
11737-429: The same as the engine RPM at that power, a transmission is used with a gear ratio to convert one to the other. At even slightly lower speeds than maximum, the total drag on the vehicle is considerably less, and the engine needs to deliver this greatly reduced amount of power. In this case the RPM of the engine has changed significantly while the RPM of the wheels has changed very little. Clearly this condition calls for
11858-406: The speed of the vehicle, while the latter varies with the square of the speed. Calculating these from first principles is generally difficult due to a variety of real-world factors, so this is often measured directly in wind tunnels and similar systems. The power produced by an engine increases with the engine's RPM to a maximum, then falls away. This is known as the point of maximum power . Given
11979-558: The sporting events of the period, bringing renown to successful entrants. The Prince Henry Tours started the evolution of reasonably large and technically advanced production sports cars. In England, the development of sporting cars was inhibited by the Motor Car Act 1903 , which imposed a speed limit of 20 mph (32 km/h) on all public roads. This led to the 1907 opening of the Brooklands motor circuit , which inspired
12100-408: The sports car is traced to the early 20th century touring cars and roadsters , and the term 'sports car' would not be coined until after World War One. A car considered to be "a sports-car years ahead of its time" is the 1903 Mercedes Simplex 60 hp , described at the time as a fast touring car and designed by Wilhelm Maybach and Paul Daimler . The Mercedes included pioneering features such as
12221-476: The sports car, but also the most important and diverse technical developments [and] very rapid and genuine improvement in the qualities of every modern production car; assisted by new design and manufacturing techniques a consistently higher level of handling properties has been achieved." In Italy, a small but wealthy market segment allowed for the manufacture of a limited number of high-performance models directly allied to contemporary Grand Prix machines, such as
12342-516: The transmission may "hunt" between OD and the next highest gear, shifting back and forth. In this case, switching it off can help the transmission to "decide". It may also be advantageous to switch it off if engine braking is desired, for example when driving downhill. The vehicle's owner's manual will often contain information and suitable procedures regarding such situations, for each given vehicle. Virtually all vehicles (cars and trucks) have overdrive today whether manual transmission or automatic. In
12463-643: The transmission. For example, the ZF 8HP transmission has 8 forward gears, two of which are overdrive (< 1:1) gear ratios. In older vehicles, it is sometimes actuated by a knob or button, often incorporated into the gearshift knob, and does not require operation of the clutch . Newer vehicles have electronic overdrive in which the computer automatically adjusts to the conditions of power need and load. The vast majority of overdrives in European cars were invented and developed by Edgar de Normanville , and manufactured by
12584-459: The use of front-wheel drive layouts, the gearbox and final drive are combined into a single transaxle. There is no longer a drive shaft between them and so the notion of "direct drive" is inapplicable. Although "overdrive" is still referred to, this is now mostly a marketing term to refer to any extra-high ratio for efficient cruising, whether it is achieved through the gearbox ratios, or by an unusually high final drive. Generally speaking, overdrive
12705-478: The war, but a small number of manufacturers returned it to prominence. In 1948, the Porsche 356 was released as the debut model from Porsche. The significance of the Porsche 356 and its successors was described in 1957 as "future historians must see them as among the most important of mid-century production cars". The 1954 Mercedes-Benz 300 SL is another significant car from this era. The 1961 Jaguar E-Type
12826-415: Was a pioneering all-wheel drive sports car. The 1995 Porsche 911 Turbo (993) saw the 911 Turbo model switch to all-wheel drive, a drivetrain layout that the model uses to this day. The BMW M3 was released in 1986 and has been produced for every generation since. The 1993-1996 Mercedes-Benz W124 E36 AMG was the mass-produced AMG model. Audi's equivalent division, called "RS", was launched in 1994 with
12947-521: Was also provided to lock out the unit mechanically. Using overdrive with the main 3-speed transmission in 2nd gear was similar in ratio to 3rd gear, and with the main transmission in third, the overall ratio was fractional (i.e., "true overdrive"). This was important in reducing wear, tear, noise, and difficulty in control. Such add-on overdrive boxes were available from the 1930s to the 1970s for cars and light trucks. Today, most petrol and diesel cars and trucks come with an overdrive transmission because of
13068-450: Was an 1,147 cc (70.0 cu in) four-cylinder with a pushrod OHV cylinder head and two valves per cylinder, using twin SU carburettors . The Herald's rack and pinion steering and coil-and-wishbone front suspension carried over, having derived from systems used by the former Alford & Alder company that had been acquired by Standard-Triumph in 1959. Rear suspension was by
13189-684: Was an unusual arrangement for a car used to compete in rallying, nonetheless it was very successful and won the World Rally Championship in 1974 , 1975 , and 1976 . The Lancia Montecarlo was produced from 1975 to 1981 and is a mid-engine two-seater, available as a coupé or a targa-top. It was sold as Lancia Scorpion in the USA. Its racing variant, Montecarlo Turbo, won the 1979 World Championship for Makes in its division and overall for 1980 World Championship for Makes and 1981 World Endurance Championship for Makes . Montecarlo also won
13310-627: Was another significant sports car of the pre-war era and is now among the most valuable cars in the world. The T57 was successful in sports car races, including winning the 1937 24 Hours of Le Mans and 1939 24 Hours of Le Mans . Another successful Bugatti sports car was the Bugatti Type 55 (1932-1935), which was based on the Type 51 Grand Prix racing car. The decade following the Second World War saw an "immense growth of interest in
13431-561: Was available as a factory option. The model was named after the famed Supermarine Spitfire fighter plane of World War II. The Spitfire evolved over five iterations: The Spitfire was conceived of by Standard-Triumph to compete in the small sports car market against the Austin-Healey Sprite . The Sprite used the drive train of the Austin A30/A35 in a new lightweight body, while the Spitfire used mechanicals from
13552-430: Was chosen to give the ratio for maximum speed. The gearbox was designed so that, for efficiency, the fastest ratio would be a "direct-drive" or "straight-through" 1:1 ratio, avoiding frictional losses in the gears. Achieving an overdriven ratio for cruising thus required a gearbox ratio even higher than this, i.e. the gearbox output shaft rotating faster than the engine. The propeller shaft linking gearbox and rear axle
13673-485: Was in 1928. Sports cars started to become popular during the 1920s. The term initially described two-seat roadsters (cars without a fixed roof), however, since the 1970s the term has also been used for cars with a fixed roof (which were previously considered grand tourers ). Attributing the definition of 'sports car' to any particular model can be controversial or the subject of debate among enthusiasts. Authors and experts have often contributed their ideas to capture
13794-490: Was now at the 100 mph (160 km/h) mark, and 0 to 60 mph (97 km/h) was reached in 13.2 seconds. Fuel economy was reduced to 29mpg. Further improvements to the suspension followed with the 1500 included longer swing axles and a lowered spring mounting point for more negative camber and a wider rear track. The wider, lower stance gave an impressive skid pad result of 0.87g average. The gearbox gained synchromesh on its bottom gear. The American market Spitfire 1500
13915-694: Was produced until 1980. Other successful lightweight roadsters include the Triumph Spitfire (1962-1980) and the Alfa Romeo Spider (1966-1993). The Fiat X1/9 (1972-1989) was unusual for its use of a mid-engine design in an affordable roadster model. A late entrant to the affordable roadster market was the 1975 Triumph TR7 , however by the late 1970s the demand for this style of car was in decline, resulting in production ceasing in 1982. The original Lotus Elan (1962-1975) two-seat coupe and roadster models are an early commercial success for
14036-675: Was released in 1964 and has remained in production since. The 911 is notable for its use of the uncommon rear-engine design and the use of a flat-six engine . Another successful rear-engine sports car was the original Alpine A110 (1961-1977), which was a successful rally car during the Group 4 era. In 1965, the BMW New Class Coupes were released, leading to the BMW 6 Series which remains in production to this day. The Lamborghini Miura (1966) and Alfa Romeo 33 Stradale (1967) mid-engined high-performance cars are often cited as
14157-487: Was replaced with a bored-out 1,296 cc unit (the bore increasing from 69.3 mm (2.73 in) to 73.7 mm (2.90 in), stroke retained at 76 mm (3.0 in)), as fitted on the new Triumph Herald 13/60 and Triumph 1300 saloons. A new quieter exhaust gave a sweet distinct note and reduced cabin noise. In SU twin-carburettor form, the engine put out a claimed 75 bhp (56 kW) at 6,000 rpm, and 75 lb⋅ft (102 N⋅m) of torque at 4,000 rpm, and made
14278-510: Was short-lived, however, as the ratio was again reduced to 7.5:1 for the remaining years of production. In the UK the 9:1 compression ratio, less restrictive emissions control equipment, and the Type HS2 SU carburettors now being replaced with larger Type HS4 models, led to the most powerful variant to date. The 1500 Spitfire now produced 71 hp (DIN) at 5,500 rpm, and produced 82 lb⋅ft (111 N⋅m) of torque at 3,000 rpm. Top speed
14399-687: Was the last and the heaviest Spitfire, weighing 1,875 lb (850.5 kg). Base prices for the 1980 model year were $ 7,365 in the US and £3,631 in the UK. Assembled at Canley in August 1980 shortly before the factory closed, the last Spitfire was an Inca Yellow UK-model including the factory hardtop and overdrive options. Never sold to the public, it remains on display at the British Motor Museum . Popular in street and rally racing, Spitfires won numerous SCCA National Sports Car Championships in F and G Production classes; won its class at
14520-412: Was to allow the drive shaft to run at lower torque, by using higher RPM. As power is the product of RPM and torque , running the shaft at higher RPM allowed more power to be transferred at lower torque. Doing so reduced the torque the driveshaft had to carry, and thus the strength and weight required. Although the designer was theoretically free to choose any ratio for the gearbox and final drive, there
14641-417: Was without a doubt the first attempt to give real performance to a road car. Many of its features, such as a honeycomb radiator and gate gear change, were continued on the much improved version which Paul Daimler designed in 1899-1900. This was of course the famous Mercedes. It also laid down standards of chassis design which were to be followed, almost unthinkingly, for the next thirty years. Several variants of
#174825